Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “error analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Surface pyrometry in presence of radiation from other sources with application to turbine blade temperature measurement

Surface pyrometry is feasible even when the amount of surface radiation is exceeded by radiation from surrounding sources. To measure and correct for this interfering radiation, several methods that use multiple wavelength pyrometry were compared by an error analysis. For a specific application to turbine blade temperature measurement in a turbofan engine, a two wavelength method was best. Auxiliary measurements at the same wavelengths substantially improve the accuracy of the method.

Buchele, D. R.↗

The development of convective instability, wind shear, and vertical motion in relation to convection activity and synoptic systems in AVE 4

Data from the Fourth Atmospheric Variability Experiment were used to investigate conditions/factors responsible for the development (local time rate-of-change) of convective instability, wind shear, and vertical motion in areas with varying degrees of convective activity. AVE IV sounding data were taken at 3 or 6 h intervals during a 36 h period on 24-25 April 1975 over approximately the eastern half of the United States. An error analysis was performed for each variable studied.

Davis, J. G.↗

Pitfalls and guidelines for the numerical evaluation of moderate-order system frequency response

The design and evaluation of a feedback control system via frequency response methods relies heavily upon numerical methods. In application, one can usually develop low order simulation models which for the most part are devoid of numerical problems. However, when complex feedback interactions, for example, between instrument control systems and their flexible mounting structure, must be evaluated, simulation models become moderate to large order and numerical problems become common. A large body of relevant numerical error analysis literature is summarized in a large language understandable to nonspecialists. The intent is to provide engineers using simulation models with an engineering feel for potential numerical problems without getting intertwined in the complexities of the associated mathematical theory. Guidelines are also provided by suggesting alternate state of the art methods which have good numerical evaluation characteristics.

Frisch, H. P.↗

Recent assessment of the performance and accuracy of a chemiluminescent rocket sonde for upper atmospheric ozone measurements

The chemiluminescent rocket ozonesonde utilizing rhodamine-B as a detector and self-pumping for air sampling has been improved. The instrument employs standard meteorological sounding systems and is the only technique available for routine nighttime ozone measurements above balloon altitudes. The chemiluminescent detector, when properly calibrated, is shown to be specific to ozone, stable, and of sufficient sensitivity for accurate measurements of ozone from about 65-20 km. An error analysis indicates that the measured ozone profiles have an absolute accuracy of about + or - 12% and a precision of about + or - 6%. Approximately 20 flights have been conducted for geophysical investigations, while additional flights were conducted with other rocket and satellite ozone soundings for comparisons. In general, these comparisons showed good agreement.

Hilsenrath, E.↗

Research developing closed loop roll control for magnetic balance systems

Computer inputs were interfaced to the magnetic balance outputs to provide computer position control and data acquisition. The use of parameter identification of a means of determining dynamic characteristics was investigated. The thyraton and motor generator power supplies for the pitch and yaw degrees of freedom were repaired. Topics covered include: choice of a method for handling dynamic system data; applications to the magnetic balance; the computer interface; and wind tunnel tests, results, and error analysis.

Covert, E. E.↗

SAR calibration technology review

Synthetic Aperture Radar (SAR) calibration technology including a general description of the primary calibration techniques and some of the factors which affect the performance of calibrated SAR systems are reviewed. The use of reference reflectors for measurement of the total system transfer function along with an on-board calibration signal generator for monitoring the temporal variations of the receiver to processor output is a practical approach for SAR calibration. However, preliminary error analysis and previous experimental measurements indicate that reflectivity measurement accuracies of better than 3 dB will be difficult to achieve. This is not adequate for many applications and, therefore, improved end-to-end SAR calibration techniques are required.

Walker, J. L.↗

Evaluation of the US/Canada wheat and barley exploratory experiment shakedown test analyst labeling results

Labeling accuracies using the reformatted labeling procedure are evaluated. The procedure is described and the decision logic applied to six LANDSAT segments from the 1978 crop year. Small grains and nonsmall grains are labeled, and small grains differentiated from barley. An error analysis was performed. Recommended changes to the reformatted procedure are presented.

Carnes, J. G.↗

A four dimensional variational analysis experiment

A demonstration that the four dimensional variational analysis method using the governing equations as exact constraints can be successfully employed for a perfect model and for a simple, but nonlinear, system is presented. The method is stable in an assimilation cycle. The method reconstructs the unobservable variables; in the case demonstrated, no velocity data was observed. The analysis errors are much smaller than the observing system errors.

Hoffman, R.↗

Proceedings of the NASA Workshop on Registration and Rectification

Issues associated with the registration and rectification of remotely sensed data. Near and long range applications research tasks and some medium range technology augmentation research areas are recommended. Image sharpness, feature extraction, inter-image mapping, error analysis, and verification methods are addressed.

Bryant, N. A.↗

Comparison of forward fuselage to Space Shuttle Orbiter flight pressure data to wind tunnel and analytical results in the hypersonic Mach number range

The Space Transportation System (STS) test program is unique in that it combines flight testing with operational flights using the first operational orbital vehicle (OV-102). The Space Shuttle Orbiter was instrumented to obtain various types of flight data. The instrumentation, designated Development Flight Instrumentation (DFI) includes pressure transducers, thermocouples, calorimeters, and accelerometers. A comparison is conducted between orbiter DFI forward fuselage flight pressure data obtained from OV-102 during the STS-1 reentry, and ground facility data obtained utilizing a 0.04 scale Orbiter forebody model. The comparisons are used to validate the existing experimental data base, optimize the pressure modeling technique, and make possible the refinement of error analysis relative to both. The obtained results indicate, in general, good agreement between flight and ground-based data.

Bradley, P. F.↗

High-resolution photographs in the rocket ultraviolet of the Orion Nebula

High-resolution photographs of the Orion Nebula have been obtained in UV bands centered near 1400, 1820, 2240 and 2620 by a 31-cm telescope mounted on an Astrobee sounding rocket. Reduction of the data by image processing, photometric calibration and error analysis steps was used to derive a matrix of values of specific intensity in absolute units. Data indicate that the Orion Nebula is primarily a reflection nebula in the UV, so that morphology is determined by the distribution of dust with respect to the illuminating stars. Ultraviolet color gradients for each color relative to the 1820-A image indicate reddening towards the outer parts of the nebula, as well as fairly symmetric dust scattering in the Theta 1 and Theta 2 Ori region. The color gradients also imply a monotonic change in scattering phase function asymmetry between 2620 and 1400 A. Total nebular flux in each bandpass is observed to be about 2.5 times the stellar flux from the Trapezium, indicating a high scattering efficiency.

Bohlin, R. C.↗

Rain measurements from space using a modified Seasat-type radar altimeter

The incorporation in the 13.5 GHz Seasat-type radar altimeter of a mode to measure rain rate is investigated. Specifically, an algorithm is developed relating the echo power at the various range bins, to the rain rate taking into consideration Mie scattering and path attenuation. The dependence of the algorithm on rain drop size distribution and nonuniform rain structure are examined and associated uncertainties defined. A technique for obtaining drop size distribution through the measurements of power at the top of the raincell and power difference through the cell also is investigated together with an associated error analysis. A description of the minor hardware modifications to the basic Seasat design is given for implementing the rain measurements.

Goldhirsh, J.↗

Turbulent boundary layer over solid and porous surfaces with small roughness

The wind tunnel models and instrumentation used as well as data reduction and error analysis techniques employed are described for an experimental study conducted to measure directly skin friction and obtain profiles of mean velocity, axial and normal turbulence intensity, and Reynolds stress in the untripped boundary on a large diameter axisymmetric body. Results are given for such a body with a (1) smooth, solid surface; (2) a sandpaper roughened, solid surface; (3) a sintered metal, porous surface; (4) a ""smooth'' performated titanium surface; (5) a rough, solid surface made of fine diffusion bonded screening; and (6) a rough, porous surface made of the same screening. The roughness values were in low range (k+ 5 to 7) just above what is normally considered ""hydraulically smooth''. Measurements were taken at several axial locations and tow or normal stream freestream velocities, 45.1 m/sec and 53.5 m/sec.

Kong, F. Y.↗

Development of computer models for the prediction of large distorted antenna characteristics

A program for calculating the radiation patterns of analytic reflector antennas, using geometric optics and aperture plane integration techniques, was modified and extended to include nonanalytic surfaces. The original program, while capable of predicting patterns for a variety of reflectors, both smooth and multipanelled, was subject to the restriction that the surface had to be expressed analytically, i.e., described by a set of mathematical equations. This restriction was removed by adapting a technique which allows the reflector configuration to be interpolated from a finite set of points measured on the surface. Criteria for choosing both the number and distribution of these measured surface points were developed by comparing the predicted antenna radiation patterns with measured laboratory results. Test cases involved relatively smooth as well as grossly distorted arbitrary surfaces. Finally, surface point accuracies were established by applying random error analysis to the measurement process.

Moskowitz, S. M.↗

The Deep Space Network: Noise temperature concepts, measurements, and performance

The use of higher operational frequencies is being investigated for improved performance of the Deep Space Network. Noise temperature and noise figure concepts are used to describe the noise performance of these receiving systems. The ultimate sensitivity of a linear receiving system is limited by the thermal noise of the source and the quantum noise of the receiver amplifier. The atmosphere, antenna and receiver amplifier of an Earth station receiving system are analyzed separately and as a system. Performance evaluation and error analysis techniques are investigated. System noise temperature and antenna gain parameters are combined to give an overall system figure of merit G/T. Radiometers are used to perform radio ""star'' antenna and system sensitivity calibrations. These are analyzed and the performance of several types compared to an idealized total power radiometer. The theory of radiative transfer is applicable to the analysis of transmission medium loss. A power series solution in terms of the transmission medium loss is given for the solution of the noise temperature contribution.

Stelzried, C. T.↗

Potential of dual-measurement techniques for accurate determination of instantaneous rainfall rate from space

The incorporation in the 13.5 GHz SEASAT type radar altimeter of a mode to measure rain rate is investigated. Specifically, an algorithm is developed relating the echo power at the various range bins to the rain rate, taking into consideration Mie scattering and path attenuation. The dependence of the algorithm on rain drop size distribution, and non-uniform rain structure are examined and associated uncertainties defined. A technique for obtaining drop size distribution through the measurements of power at the top of the raincell and power difference through the cell is also investigated together with an associated error analysis. A description of the minor hardware modifications to the basic SEASAT design is given for implementing the rain measurements.

Ulbrich, C. W.↗

Transformation of two and three-dimensional regions by elliptic systems

Finite difference methods for composite grids were analyzed. It was observed that linear interpolation between grids would suffice only where low order accuracy was required. In the context of fluid flow, this would be in regions where the flow was essentially free stream. Higher order interpolation schemes were also investigated. The well known quadratic and cubic interpolating polynomials would increase the formal accuracy of the overall numerical algorithm. However, it can also be shown that the stability of the algorithm may be adversely affected. Further numerical results are needed in order to assess the nature of this instability induced by the interpolation procedure. Finally, error analysis and the order of difference expressions on general curvilinear coordinates are discussed.

Thompson, J. F.↗