Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrochemical modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Modelling and Experimental Validation of Improved Performance of Lithium-Ion Batteries Having Thick Electrodes with Laser-Ablated Micro-Structures

For widespread adoption of electric vehicles, lithium-ion batteries (LiBs) need to achieve energy densities of >275 Wh/kg, cost less than $100/Wh, and charge to more than 80% capacity within 15 minutes. Increasing the battery electrode thicknesses is one way to increase cell energy densities while also saving on cell manufacturing cost by increasing the ratio of electrode active material to inactive material within each cell. However, increased electrode loading is often accompanied by decreased Li+-ion diffusion across the full thick electrodes. This leads to significant cell polarization that prevents full capacity utilization and accelerates cell degradation, especially at fast charging/discharging rates. The introduction of secondary pore networks in thick battery electrodes alleviates some of the trade-offs between energy and power performance. These microstructures provide low tortuosity pathways for facile Li+-ion diffusion deep into the thick electrodes, diminishing detrimental concentration gradients within the cell. Ultrafast-pulsed laser ablation is a promising method to introduce micro pores or channels in thick battery electrodes as it allows for precise control of pattern geometries, results in minimal damage to the electrode and can be introduced into existing roll-to-roll electrode manufacturing lines. Herein, the limitations of thick planer electrodes and the advanced predictive models to identify optimal electrode patterns for improved cycling performance will be presented. The impact of electrode laser patterning to create secondary pore networks also will be discussed. Materials characterization techniques (SEM-EDS, XRD) were used to explore the affect ultrafast laser ablation had on the electrode materials’ morphology and structure. The improvements in the patterned electrodes’ electrochemical cycling performances and degrees of wetting will be compared to a pristine baseline case. Finally, the discrepancies between experimentally obtained data and model predictions will be explained.

DIRECT ENERGY CONVERSION,ENERGY STORAGE↗
DOE OSTI2024

Studying Transient Phenomena in Thin Films with Reinforcement Learning

Neutron reflectometry has long been a powerful tool to study the interfacial properties of energy materials. Recently, time-resolved neutron reflectometry has been used to better understand transient phenomena in electrochemical systems. Those measurements often comprise a large number of reflectivity curves acquired over a narrow q range, with each individual curve having lower information content compared to a typical steady-state measurement. In this work, we present an approach that leverages existing reinforcement learning tools to model time-resolved data to extract the time evolution of structure parameters. Further, by mapping the reflectivity curves taken at different times as individual states, we use the Soft Actor-Critic algorithm to optimize the time series of structure parameters that best represent the evolution of an electrochemical system. We show that this approach constitutes an elegant solution to the modeling of time-resolved neutron reflectometry data.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Electronic and Structural Properties of the Polymer-Electrolyte Interphase in Electrochemically Doped Polymers

The advance of soft, polymer-based (photo)electrochemical energy transformation and storage applications requires a framework for polymer and electrolyte design that includes a deep understanding of the polymer–electrolyte interphase. Here, we report on the investigations of two napthalenediimide (NDI)–bithiophene (T2)-based semiconducting copolymers using computational modeling and in situ, ex situ, and operando techniques to reveal how changes in electrolyte and polymer chemistry modulate the electronic and structural properties of polymer electrodes during electrochemical (de)doping. These systems are shown to host an ensemble of polarons, in contrast with the single polaron-like character often reported, whose properties vary with the nature of the local environment. Importantly, these polarons serve as reporters of the nanoscale environments in which they reside. We demonstrate that controlling the polymer and electrolyte chemistry regulates the nature of the charge carriers generated upon electrochemical doping and/or exciton dissociation in a photoelectrochemical solar cell: For instance, divalent counterions enable polaron and bipolaron formation at lower reducing potentials, while supporting more bipolaron formation than monovalent counterions. A novel application of NEXAFS reveals insights into charge (de)localization, providing a pathway for future investigation of electron transport mechanisms. Finally, simulations of polymer swelling of an amorphous interphase show that charge formation has a large impact on polymer swelling and ion penetration. These studies deliver insights to enable the control of charge-carrier and ion transport, the rates of electron transfer and catalytic efficiency, device stability, and overall device performance.

14 SOLAR ENERGY↗
DOE OSTI2024

Reversible Methane Electrochemical Reactors as Efficient Energy Storage for Fossil Power

The overall objective of the project was to conduct a comprehensive Research & Development (R&D) program to demonstrate the suitability and future advancement and integration of reversible methane protonic ceramic electrochemical reactors (PCERs) as an efficient Energy Storage System (ESS) with fossil fuel power plants. Fundamental process and system models are developed to conduct a preliminary conceptual study and investigate the power plant system integration requirements, performance requirements, and technical and non-technical gaps for eventual implementation at system level. Technology maturation requirements is also investigated through identifying the critical technical elements and networking with industrial technology developers and end-users.

08 HYDROGEN↗
DOE OSTI2023

Intermediate Temperature Proton‐Conducting Solid Oxide Electrolysis Cells with Improved Performance and Durability

Technical understanding: A high-performance and stable intermediate temperature proton-conducting solid oxide electrolysis cell (PCEC) will add significantly to the hydrogen roadmap of EERE. However, the low electrocatalytic activity of the air electrode and the instability of the electrolyte are technical barriers. In this research, we utilized computational fluid dynamic modeling and materials/microstructure engineering to investigate the complex reaction chain and to improve the performance and reliability of the protonic ceramic electrochemical cells. An active and stable Pr 1.8 Ba 0.2 NiO 4+δ -BaZr 0.1 Ce 0.7 Y 0.1 Yb 0.1 O 3-δ (BZCYYb) scaffold conformal coating electrode was rationally designed where the robust Pr 1.8 Ba 0.2 NiO 4+δ functions both as a catalytic active and a protective layer. The PCECs with porosity-optimized scaffold conformal coating electrodes demonstrate 1.46 Acm -2 under 1.3 V at 600°C, which is among the highest in recent years. The final optimization by computational fluid dynamic modeling and conformal coating technique was applied to evolve the PCEC air electrode from Pr 2 NiO 4+δ to Pr 1.8 Ba 0.2 NiO 4+δ -BaZr 0.1 Ce 0.7 Y 0.1 Yb 0.1 O 3-δ scaffold conformal coating. The electrolysis current was boosted from 0.445A/cm 2 to 1.46A/cm 2 at 600°C and 1.3V. A superior low degradation rate of 1mV/kh was achieved in a 5000-hour of operation. Technical effectiveness and economic feasibility: The effectiveness of this TCO conformal coating on electrolyte backbone as air electrode has been proven by long-term demonstration. Based on the highly conductive BZCYYb electrolyte and the TCO steam electrode PNO, this project rationally took advantage of the existent materials to structure a PCEC device with high TRL and low risk. The solution infiltration method used to structure the conformal coating is a standard method used by the solid oxide cell community. Very minimal adoption is needed in the current SOC fabrication process. It is a cost-effective, scalable method for manufacturing, and brings up remarkable impact on the current technical status of PCEC. Benefit to the public: The findings in the research showed the industry that the severe challenge in PCEC can be overcome in a practical way. A various energy-hydrogen ecosystem is not beyond reach. The success of this technology provides sustainable and affordable H 2 to society. It will stimulate investment from the governmental and private sectors in response to the device manufacture and deployment, and the related infrastructure construction. It will generate high-pay domestic jobs and environmental benefits to the general public in the United States.

08 HYDROGEN↗
DOE OSTI2022

Tuning Surface Acidity of Mixed Conducting Electrodes: Recovery of Si‐Induced Degradation of Oxygen Exchange Rate and Area Specific Resistance

Abstract Metal oxides are an important class of functional materials, and for many applications, ranging from solid oxide fuel/electrolysis cells, oxygen permeation membranes, and oxygen storage materials to gas sensors (semiconducting and electrolytic) and catalysts, the interaction between the surface and oxygen in the gas phase is central. Ubiquitous Si‐impurities are known to impede this interaction, commonly attributed to the formation of glassy blocking layers on the surface. Here, the surface oxygen exchange coefficient ( k chem ) is examined for Pr 0.1 Ce 0.9 O 2‐δ (PCO), a model mixed ionic electronic conductor, via electrical conductivity relaxation measurements, and the area‐specific resistance (ASR) by electrochemical impedance spectroscopy. It is demonstrated that even low silica levels, introduced by infiltration, depress k chem by a factor 4000, while the ASR increases 40‐fold and we attribute this to its acidity relative to that of PCO. The ability to fully regenerate the poisoned surface by the subsequent addition of basic Ca‐ or Li‐species is further shown. This ability to not only recover Si‐poisoned surfaces by tuning the relative surface acidity of an oxide surface, but subsequently outperform the pre‐poisoned response, promises to extend the operating life of materials and devices for which the catalytic oxygen/solid interface reaction is central.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Heterocyclic Chromophore Amphiphiles and their Supramolecular Polymerization

Abstract Supramolecular polymerization of π‐conjugated amphiphiles in water is an attractive approach to create functional nanostructures. Here, we report on the synthesis, optoelectronic and electrochemical properties, aqueous supramolecular polymerization, and conductivity of polycyclic aromatic dicarboximide amphiphiles. The chemical structure of the model perylene monoimide amphiphile was modified with heterocycles, essentially substituting one fused benzene ring with thiophene, pyridine or pyrrole rings. All the heterocycle‐containing monomers investigated underwent supramolecular polymerization in water. Large changes to the monomeric molecular dipole moments led to nanostructures with low electrical conductivity due to diminished interactions. Although the substitution of benzene with thiophene did not notably change the monomer dipole moment, it led to crystalline nanoribbons with 20‐fold higher electrical conductivity, due to enhanced dispersion interactions as a result of the presence of sulfur atoms.

Đorđević, Luka↗
DOE OSTI2023

Heterocyclic Chromophore Amphiphiles and their Supramolecular Polymerization

Abstract Supramolecular polymerization of π‐conjugated amphiphiles in water is an attractive approach to create functional nanostructures. Here, we report on the synthesis, optoelectronic and electrochemical properties, aqueous supramolecular polymerization, and conductivity of polycyclic aromatic dicarboximide amphiphiles. The chemical structure of the model perylene monoimide amphiphile was modified with heterocycles, essentially substituting one fused benzene ring with thiophene, pyridine or pyrrole rings. All the heterocycle‐containing monomers investigated underwent supramolecular polymerization in water. Large changes to the monomeric molecular dipole moments led to nanostructures with low electrical conductivity due to diminished interactions. Although the substitution of benzene with thiophene did not notably change the monomer dipole moment, it led to crystalline nanoribbons with 20‐fold higher electrical conductivity, due to enhanced dispersion interactions as a result of the presence of sulfur atoms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Concentration‐dependent Cycling of Phenothiazine‐based Electrolytes in Nonaqueous Redox Flow Cells

Increasing redox-active species concentrations can improve viability for organic redox flow batteries by enabling higher energy densities, but the required concentrated solutions can become viscous and less conductive, leading to inefficient electrochemical cycling and low material utilization at higher current densities. To better understand these tradeoffs in a model system, we study a highly soluble and stable redox-active couple, N-(2-(2-methoxyethoxy)ethyl)phenothiazine (MEEPT), and its bis(trifluoromethanesulfonyl)imide radical cation salt (MEEPT-TFSI). We measure the physicochemical properties of electrolytes containing 0.2–1 M active species and connect these to symmetric cell cycling behavior, achieving robust cycling performance. Specifically, for a 1 M electrolyte concentration, we demonstrate 94% materials utilization, 89% capacity retention, and 99.8% average coulombic efficiency over 435 h (100 full cycles). This demonstration helps to establish potential for high-performing, concentrated nonaqueous electrolytes and highlights possible failure modes in such systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Failure analysis of solid oxide fuel cells nickel-yttria stabilized zirconia anode under siloxane contamination

In this study, the failure process of the solid oxide fuel cell (SOFC) Ni-yttria-stabilized zirconia (YSZ) anode is investigated with D4 siloxane (octamethylcyclotetrasiloxane) contamination. In order to evaluate the influence of the electrochemical reaction on the siloxane deposition process, the SOFC experiments were operated at open circuit voltage (OCV) and 50 mA cm -2 conditions at 800°C. During the failure process, electrochemical, morphology and exhaust gas component analysis testing are conducted at the critical points. An equivalent circuit model and corresponding microstructure parameter calculations for separated physicochemical processes were utilized for the quantitative analysis of the failure process. Further, the results confirm the siloxane chemical adsorption deposition mechanism proposed in previous work. As a result, the failure of the anode was attributed to the gas diffusion blockage by dense silicon dioxide layer formation. The anode failure process with siloxane contamination is faster when the anode is operated under polarization.

25 ENERGY STORAGE↗
DOE OSTI2026

Analysis of the electrical double layer using electrochemical X-ray photoelectron spectroscopy

The element-sensitivity of X-ray spectroscopies offers the potential to disentangle the individual chemistries of water, ions, and adsorbates at the electrode-electrolyte interface in an element-by-element manner. However, targeted experimental design is needed to establish interface-sensitive in situ X-ray spectroscopy in a realistic electrochemical environment. Here, we demonstrate how electrochemical X-ray photoelectron spectroscopy (EC-XPS) in the dip-and-pull geometry can be used to specifically probe the behavior of ions in the electrical double layer. Taking the case study of a polycrystalline Au foil in 50 mM KClO 4 electrolyte, we tracked the electrochemical response of interfacial K + cations across a broad potential range. We show how, in combination with modeling, key parameters such as the potential of zero charge (PZC), ion packing behavior, dielectric saturation, and the electrostatic potential decay in the double layer can be extracted from the data. Importantly, we also analyze how the experimental conditions and non-idealities can influence the results and put forward criteria for reliable experimentation and data analysis.

Dip-and-pull↗
DOE OSTI2021

Bioinspired nonwetting surfaces for corrosion inhibition over a range of temperature and corrosivity

Applications of superhydrophobic (SHS) and lubricant infused surfaces (LIS) involve exposure to corrosive environments from the acidic to the basic, at a range of temperatures, that are not fully characterized. Here, we present for the first time a multifactorial study of the effects of surface fabrication method, surface modification, surface functionalization time, temperature and pH of the immersion medium on the corrosion performance of nonwetting copper surfaces. Bioinspired SHS and LIS fabricated using facile methods of etching and electrodeposition are systematically assessed using potentiodynamic polarization measurements for their corrosion resistance in saline solution (pH ≈7) over a temperature range 23–85°C. SHS and LIS are shown to exhibit diminished corrosion rate, by up to two orders of magnitude, compared to bare copper surface. An Arrhenius model is developed for the first time, describing the temperature- dependent corrosion rate of SHS and LIS. Electrochemical impedance spectroscopy is used to show that corrosion resistance of LIS is larger by three orders of magnitude in extremely acidic (pH = 1) and by an order magnitude in extremely alkaline (pH = 14) media compared to bare copper surface. Etched LIS are generally more resistant to corrosion compared to SHS at all temperatures with excellent microstructural durability.

42 ENGINEERING↗
DOE OSTI2024

Toward Spatial Control of Reaction Selectivity on Photocatalysts Using Area-Selective Atomic Layer Deposition on the Model Dual Site Electrocatalyst Platform

Photocatalytic water splitting is a promising route to low-cost, green H 2 . However, this approach is currently limited in its solar-to-hydrogen conversion efficiency. One major source of efficiency loss is attributed to the high rates of undesired side and back reactions, which are exacerbated by the proximity of neighboring oxidation and reduction sites. Nanoscopic oxide coatings have previously been used to selectively block undesired reactants from reaching active sites; however, a coating encapsulating the entire photocatalyst particle limits activity as it cannot facilitate both half-reactions. In this work, area selective atomic layer deposition (AS-ALD) was used to selectively deposit semipermeable TiO 2 films onto model metallic cocatalysts for enhancing reaction selectivity while maintaining a high overall activity. Pt and Au were used as exemplary reduction and oxidation cocatalyst sites, respectively, where Au was deactivated toward ALD growth through self-assembled thiol monolayers while TiO 2 was coated onto Pt sites. Electroanalytical measurements of monometallic thin film electrodes showed that the TiO 2 -encapsulated Pt effectively suppressed undesired H 2 oxidation and Fe(II)/Fe(III) redox reactions while still permitting the desired hydrogen evolution reaction (HER). A planar model photocatalyst platform containing patterned interdigitated arrays of Au and Pt microelectrodes was further assessed using scanning electrochemical microscopy (SECM), demonstrating the successful use of AS-ALD to enable local reaction selectivity in a dual-reaction-site (photo)electrocatalytic system. Finally, interdigitated microelectrodes having independent potential control were used to show that selectively deposited TiO 2 coatings can suppress the rate of back reactions on neighboring active sites by an order of magnitude compared with uncoated control samples.

08 HYDROGEN↗
DOE OSTI2023

Heterogenous electromediated depolymerization of highly crystalline polyoxymethylene

Abstract Post-consumer plastic waste in the environment has driven the scientific community to develop deconstruction methods that yield valued substances from these synthetic macromolecules. Electrocatalysis is a well-established method for achieving challenging transformations in small molecule synthesis. Here we present the first electro-chemical depolymerization of polyoxymethylene—a highly crystalline engineering thermoplastic (Delrin®)—into its repolymerizable monomer, formaldehyde/1,3,5-trioxane, under ambient conditions. We investigate this electrochemical deconstruction by employing solvent screening, cyclic voltammetry, divided cell studies, electrolysis with redox mediators, small molecule model studies, and control experiments. Our findings determine that the reaction proceeds via a heterogeneous electro-mediated acid depolymerization mechanism. The bifunctional role of the co-solvent 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP) is also revealed. This study demonstrates the potential of electromediated depolymerization serving as an important role in sustainable chemistry by merging the concepts of renewable energy and circular plastic economy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

How Interface Evolution at the Nanoscale Dictates Protonic Ceramic Cell Behavior

Understanding the effects of heterointerfaces in nanodevices remains a challenge in interface engineering for systems applied in solid oxide fuel cells, catalysis, sensors, and memristors [1]. Previous studies have shown that the presence of interfaces in ceramic oxide nanodevices affects their impedance properties compared to bulk systems [2]. In this work, we analyze a thin-film model system designed to study the interfaces between representative electrode and electrolyte materials employed in protonic ceramic electrochemical cells for the reversible conversion of hydrogen o electricity. The investigated device features a 21-layer architecture that alternates between an electrode material PBSCF (PrBa 0.5 Sr 0.5 Co 1.5 Fe 0.5 O 5+ϵ ) and a proton-conducting electrolyte BZY (BaZr 0.8 Y 0.2 O 3-δ ), with uniform 20 nm thickness for each layer. Here, the device was fabricated using Pulsed Laser Deposition (PLD) and supported on a conductive Nb-doped STO (Nb-SrTiO 3 ) substrate.

dos Santos, Gabriel T. [Northwestern University, E↗
DOE OSTI2021

Minimizing Cr-Evaporation from Balance Of Plant Components By Utilizing Cost-Effective Alumina-Forming Austenitic Steels

A solid oxide fuel cell (SOFC) is a clean and efficient energy conversion device. The development of intermediate-temperature SOFCs has made it preferable to use metallic interconnects (MICs) to greatly reduce the cost and significantly increase the efficiency compared to ceramic interconnect materials. However, gaseous chromium species will evaporate from the chromium-containing layer formed on the surface of commonly used MICs and balance of plant (BoP) components. Volatile chromium species have been shown to form solid deposits which poison the cathodes of SOFCs, causing drastic cell performance degradation and thereby limiting commercialization. In order to alleviate the Cr poisoning and achieve long-term high performance of SOFC stacks, various Al 2 O 3 -forming austenitic (AFA) stainless steels applied at different temperatures are evaluated in this project. Based on our Phase I results (500 h operation), it is shown that on the AFAs, an alumina-based protective layer forms under high temperature that is invulnerable to water vapor effects and suppresses the diffusion of chromium and manganese which can prevent the generation of spinels on the alloy surface. Therefore, 310S, OC4 and OC5 at 800 °C and 625, OC11 and OC11LZ at 900 °C are selected to be tested in the Phase II long-term operation. From the results, we find that besides the lower Cr evaporation rates and better oxidation resistance of AFAs than benchmark alloys after short-term (500 h) operation, AFAs also possess the sturdy and compact alumina layer after a long-term operation (5000 h). A protective oxide layer is of great importance for the long-term high-temperature operation of structural materials. The high-temperature oxidation behavior of AFAs and commercial 310S and 625 alloys in Air + 10% H 2 O at 800 °C and 900 °C is systematically investigated. Severe breakaway oxidation and minor spallation are observed for the 310S and 625 after the long-term operation, while the AFAs show high oxidation resistance. It is found that the formation of a continuous alumina layer could greatly prevent the volatilization of chromium vapors. In addition, the corresponding evolving models are discussed. Chromium evaporation from BoP components in high-temperature environment could severely deteriorate the electrochemical performance of SOFC. Several methods were applied to evaluate the Cr evaporation rates of BoP after 500 h exposure at 800 °C to 900 °C in air with 10% H 2 O. An optimal method was designed to exclude the effect of silicon (Si) deposits from quartz tube and sodium (Na) deposits from the sodium carbonate on the oxidation process and the chemical interaction between Cr gaseous species and alumina tube which could provide further quantitative correlation of the evaporated Cr species quantities and degradation rates of SOFC. Based on the great performance of AFAs after long-term operation, AFAs are assembled with Anode-supported cells (ASC) to investigate the the Cr deposition of anode-supported cell under a constant current density of 0.5 A cm -2 at 800 °C with AFA alloys compared with commercial alloys. In addition, the anodic and cathodic processes are deconvoluted by distribution of relaxation times (DRT) method which are comprehensively discussed. It is found out that the voltage exhibited a slight decrease of 5.09 % and 1.54 % in the presence of OC11 and OC11LZA alloy, respectively. However, a considerable decrease of 22.14 % and 12.06 % was determined in the presence of 310S and 625 alloy, respectively. AFAs possessing the low-cost, low Cr evaporation rates and the high oxidation resistance will make it of great potential to replace the existing BoP components.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Corrosion Behavior of Hydrophobic Coatings in Aqueous CO2 Environments

Internal corrosion is caused by gas impurities such as CO2, moisture, and H2S, leading to material degradation. To combat this, the National Energy Technology Laboratory (NETL) developed a novel hydrophobic coating to reduce surface hydrophobicity and enhance the corrosion resistance of steel. NETL’s approach uses multi-layer hydrophobic coatings, a novel and promising coating that could potentially revolutionize the industry's approach to internal corrosion mitigation. This work aims to investigate the corrosion performance of the hydrophobic coating and determine the water uptake. Electrochemical corrosion experiments were carried out on bare X65 carbon steel without and with coating in 3.5 wt.% NaCl saturated with CO2 at 20 °C to follow the water uptake as a function of exposure time. Linear polarization resistance (LPR) was used to determine the corrosion rate for carbon steel immersed in a NaCl electrolyte saturated with CO2. Electrochemical impedance spectroscopy (EIS) of uncoated and coated bare carbon steel was investigated. The analyses of impedance models and water uptake behaviors of hydrophobic coatings were studied for 200 hours during the corrosion process. The water uptake was estimated using the Brasher and Kingsbury relation. The results showed that the superhydrophobic coating that was developed used innovative nano-based materials to act as protection layers on the surface of metallic parts against mechanical aggressors, corrosion, and fouling agents.

corrosion behavior↗