Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “composition and microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Additive Manufactured Composite Phase-Change Material for Thermal Energy Storage Applications

Phase-change materials play a critical role in industrial energy storage applications to drive efficiency improvements, thermal energy management, and carbon emissions reductions. Recently, it has been shown that rapid solidification of alloys with metastable immiscibility in the liquid phase has the potential to form unique microstructures in which a low-melting phase is uniformly distributed in a high-melting matrix. This feature can be exploited using additive manufacturing to produce components with complex geometries containing such unique phase-change microstructures. Phase-field simulations utilizing high-performance computing were used to provide a detailed description of the evolution of the active phase during service in terms of their morphology and composition in different polycrystalline matrix grain morphologies that are typically produced during additive manufacturing. Phase field simulations were performed using, MEUMAPPS-SL (Microstructure Evolution Using Massively Parallel Phase-field Simulations – Solid Liquid) code that was developed in-house by the Oak Ridge National Laboratory. The simulations utilized the capabilities of the Kestrel supercomputer at the National Renewable Energy Laboratory. The simulation results were compared with experimental results generated at Siemens Energy, Inc. The results indicate that the kinetics of liquid spreading along grain boundaries is largely determined by the mobility of the triple line along the intersection of the grain boundary liquid and the grain boundary plane.

25 ENERGY STORAGE↗
DOE OSTI2023

Compositional inhomogeneity and its effect on the hardness of nanostructured refractory high-entropy alloys

The pronounced compositional inhomogeneity observed in refractory high-entropy alloys (HEAs), as opposed to non-refractory HEAs, has an important influence on their mechanical properties, thereby posing a significant challenge for the development of high-performance refractory HEAs. In this work, by combining transmission electron microscopy imaging, chemical analysis, and nano-hardness tests, we investigate the compositional inhomogeneities in a series of sintered nanostructured HEAs and elucidate their influence on the material's hardness. Further, we reveal that the compositional inhomogeneity of the sintered nanostructured HEAs is temperature- and component- dependent. By correlating the hardness of nanostructured HEAs to the evolving compositional inhomogeneity, our work demonstrates that the compositional inhomogeneity in nanostructured HEAs can be tuned by sintering temperature or alloying towards optimized microstructure and hardness.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Aging heat treatment design for Haynes 282 made by wire-feed additive manufacturing using high-throughput experiments and interpretable machine learning

Wire-feed additive manufacturing (WFAM) produces superalloys with complex thermal cycles and unique microstructures, often requiring optimized heat treatments. To address this challenge, we present a hybrid approach that combines high-throughput experiments, precipitation simulation, and machine learning to design effective aging conditions for the WFAM Haynes 282 superalloy. Our results demonstrate that the γ’ radius is the critical microstructural feature for strengthening Haynes 282 during post-heat treatment compared with the matrix composition and γ’ volume fraction. New aging conditions at 770°C for 50 hours and 730°C for 200 hours were discovered based on the machine learning model and were applied to enhance yield strength, bringing it on par with the wrought counterpart. This approach has significant implications for future AM alloy production, enabling more efficient and effective heat treatment design to achieve desired properties.

CALPHAD↗
DOE OSTI2021

Structure-Property Relationships of Additively Manufactured Ni-Nb Alloys [Slides]

In this work, scratch and nanoindentation testing was used to determine hardness, fracture toughness, strain rate sensitivity, and activation volumes on additively manufactured graded and uniform Ni-Nb bulk specimens. Characterization showed the presence of a two phase system consisting of Ni 3 Nb and Ni 6 Nb 7 intermetallics. Intermetallics were multimodal in nature, having grain and cell sizes spanning from a few nanometers to 10s of micrometers. The unique microstructure resulted in impressively high hardness, up to 20 GPa in the case of the compositionally graded sample. AM methods with surface deformation techniques are a useful way to rapidly probe material properties and alloy composition space.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Structure-Property Relationships of Additively Manufactured Ni-Nb Alloys [Slides]

In this work, scratch and nanoindentation testing was used to determine hardness, fracture toughness, strain rate sensitivity, and activation volumes on additively manufactured graded and uniform Ni-Nb bulk specimens. Characterization showed the presence of a two phase system consisting of Ni 3 Nb and Ni 6 Nb 7 intermetallics. Intermetallics were multimodal in nature, having grain and cell sizes spanning from a few nanometers to 10s of micrometers. The unique microstructure resulted in impressively high hardness, up to 20 GPa in the case of the compositionally graded sample. AM methods with surface deformation techniques are a useful way to rapidly probe material properties and alloy composition space.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Additive Manufacture of Multi-Functional, Large-Scale Components

The poster summarizes the main results for a LDRD focused on developing a arc-based additive manufacturing (AM) system capable of fabricating large components with a composition gradient otherwise known as functionally graded materials (FGMs). FGMs are capable of addressing local extreme conditions in an optimal and cost-effective manner. The AM system (referred to as multi-Wire Arc Additive Manufacturing or m-WAAM) consisted of modifying a standard automated gas tungsten arc welding system to deliver multiple welding wires to the weld pool at controlled rates to deposit desired alloy compositions at critical locations. Numerous shapes and composition gradients were fabricated with the system and the effect of various deposition parameters on the nature of the composition profile were evaluated. Additionally, heat treatment of the FGM was performed to develop graded microstructures which should enhance dynamic impact performance of inexpensive steels. The project highlights the potential of m-WAAM to efficiently fabricate FGMs. However, this project only explored the science behind the technique and additional development work will be required to develop a fully-functional system that can build more complex components.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Phase equilibria and microstructure evolution in the Ni-rich region of binary Ni-Ce and ternary Ni-Ce-X (X=Al, Nb, Cr, Ti) systems at 900 °C

The equilibrium compositions of all phases in the Ni-rich region of binary Ni-Ce and ternary Ni-Ce-X (X=Al, Nb, Cr, Ti) systems at 900 °C were determined experimentally through isothermal annealing for up to 500 h and compared with currently available computational thermodynamic descriptions. Additionally, the study examined how adding a third element to the binary system affects the microstructure by analyzing changes in the volume fraction of the intermetallic phase in the eutectic region. It was observed that Nb and Ti addition lowered the intermetallic fraction in the eutectic region while Al and Cr addition did the opposite. The fraction of intermetallic phase in the eutectic region is very important because it contributes to extreme brittleness of these alloys. Also, Al, Nb and Ti addition promoted different precipitates upon annealing when added in sufficient amounts. The collected data on composition and phase equilibria provides crucial information for improving the thermodynamic assessments of the binary and ternary alloy systems.

energy dispersive spectrometry↗
DOE OSTI2026

Synthesis, Characterization, and Testing of High-Lithium-Density Composite Breeders

Solid tritium breeder materials must first and foremost have sufficiently high concentrations of lithium to enable a plant-scale tritium breeding ratio greater than 1:1. However, in addition to lithium content, such breeder materials must also meet other performance metrics including high tritium release rates, thermal conductivities, and irradiation damage tolerance. Perhaps most importantly, tritium breeders must maintain their mechanical integrity during reactor operation so as to avoid degradation which can jeopardize the functionality of the tritium breeder blanket module, which in most designs takes the form of a pebble bed geometry. Unfortunately, the mechanical robustness of most lithium-bearing ceramics under investigation for fusion applications is often inversely related to the lithium atom density. For example, a material such as lithium oxide (Li2O), which has one of the highest lithium atom densities, has a much lower mechanical splitting strength than lithium metatitanate (Li2TiO3), though Li2TiO3 has less than half the lithium atom density of Li2O. This work seeks to provide an alternative to monolithic ceramic tritium breeders, in the form of metal-reinforced composite tritium breeders. Specifically, composite tritium breeders have been synthesized combining Li2O with various ferrous metal reinforcements via electric field assisted sintering (EFAS), also known as spark plasma sintering (SPS). As the metal reinforcement content is increased, metallic networks are observed, via electron microscopy and X-ray computed tomography, to form throughout the composite material. Through destructive mechanical testing, even dilute metal reinforcement loading enables drastic mechanical strength improvements over pure Li2O while higher loadings give rise to quasi-ductile behavior and higher ultimate strengths than Li2TiO3 – while still maintaining a higher density of lithium atoms than Li2TiO3 and many other breeder candidates. In addition to microstructural characterization and mechanical testing, thermal property measurements and hydrogen permeability testing are underway to further assess the suitability of such composites for fusion reactor applications.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Novel Materials R&D for Next-Generation Accelerator Target Facilities

High-Entropy Alloys and Electrospun Nanofiber materials are two classes of novel materials that can offer improved resistance to beam-induced radiation damage and thermal shock. Research to develop these new materials specifically for multi-megawatt accelerator target applications, such as beam windows and particle-production targets, are ongoing at Fermilab within the scope of a DOE Early Career Research Program. The research program combines in-beam experiments with complementary simulations to tailor the microstructures of these novel materials for use in next-generation accelerator target facilities. Iterative simulations to optimize the material composition, physics performance, and beam-induced thermomechanical response will guide the material design and fabrication processes based on established figures of merit. This will be followed by material irradiation experiments using low-energy ions and prototypic high-energy protons with extensive post-irradiation material characterization to assess and qualify the selected novel materials. This talk will describe the alloy design and synthesis, microstructural pre-characterization of the alloys, and plans for the eventual down selection following low-energy ion irradiation studies.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Residual stress and microstructure in IN718-René41 graded superalloy fabricated by laser blown directed energy deposition

Additively printed Ni-based superalloy with a compositionally graded transition from IN718 to René41 was fabricated by laser blown-powder directed energy deposition (DED/LB-M), with the goals of meeting location-specific temperature capability and reducing component cost for hot gas path turbine components. Residual stress distribution in thin wall specimens with three sets of DED build parameters in the as-built and stress-relieved states was measured by neutron diffraction. For calculating residual stress, the calculated d0 method was found to be more appropriate as stress-free reference than using the lattice spacing measured from the stress-relief heat treated specimens. Longer dwell time (lower interpass temperature), higher energy input, smaller layer thickness resulted in a higher magnitude of tensile residual stresses at edges and compressive residual stresses at center of the specimens. The residual stress results did not show a strong dependence on graded compositions, indicating that the residual stress build-up was more geometry and process dependent. Non-destructive neutron imaging based on the attenuation coefficient qualitatively visualized the compositional variation in the bulk and showed good agreement with quantitative Electron Probe Micro-Analysis (EPMA) measurement. Grain structure, texture, and residual plastic strain along the build direction were characterized by Electron Backscatter Diffraction (EBSD). Long columnar grains with (001) preferred grain orientation were dominant along the build direction. Compositional change did not show an obvious effect on the epitaxial growth of dendrites and the continuation of the columnar grains. Residual plastic strain was relatively low in the as-built specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Genesis of a novel high-rate composite manufacturing process using large-scale additive manufacturing – compression molding (AM-CM) system: Possibilities and limitations

Oak Ridge National Laboratory (ORNL) has developed a highly automated manufacturing process for thermoplastic composites that combines the benefits of Additive Manufacturing and Compression Molding (AM-CM) to produce high-performance functional composite structures at automotive production rates. Here, the AM-CM process creates highly precise preforms by additively placing extruded fiber-filled polymers (with controlled fiber orientations and multi-material configurations) in the desired mold location before undergoing a secondary compression molding process immediately before the preform cools down. Preforms can be in the form of short, long-chopped, or continuous fiber-filled thermoplastic polymers (e.g., CF/GF-filled ABS, PC, LM-PAEK, etc.). The AM-CM process combines the benefits of controlled fiber alignment, that is only achievable in AM-printed parts with the classical CM process, which eliminates porosity and good surface finish. A preform created using AM-CM can integrate various materials to enable additional architectural functionalities, including over-molding, selective stiffening, and the incorporation of electrically or thermally conductive channels. All these advantages come with a fast part production cycle time. The AM-CM process can manufacture multi-material, multi-functional parts in under 3 min, starting from raw material (pellets) to the final product. The novel AM-CM process offers superior microstructural control and enhanced multi-functionality previously unattainable with any other traditional high-rate thermoplastic composite manufacturing method. This work covers the manufacturing concept, system development, materials and applications of AM-CM process in detail.

Kumar, Vipin [Oak Ridge National Laboratory (ORNL)↗
DOE OSTI2021

Cement stress and microstructure evolution during curing in semi-rigid high-pressure environments

The process of cement slurry curing into a solid has a direct effect on the initial state of stress in a composite concrete and steel structure. Failure models for critical infrastructure and wellbores could benefit from measurements of this initial stress because it greatly influences structural performance. Here, we present measurements of the initial stress state (total stress, effective stress, and pore pressure) of multiple cement formulations cured under a high-pressure of 40 MPa within a semi-rigid steel pipe. Our results show that cements cured in this restrained environment exhibit dense microstructures with low permeability (nano-Darcy), develop an anisotropic stress state greater than zero and less than the curing pressure, and undergo a staged curing process where hydration and mechanical behaviors evolve from a slurry into a pre-stressed porous medium. Both drained and undrained scenarios were investigated, revealing a feedback from the semi-rigid boundary towards improved cement performance.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Mechanical Behavior of Neutron Irradiated Refractory Multi-Principal Element Alloys Processed via Spark Plasma Sintering

The search for advanced materials capable of withstanding the extreme conditions of Generation IV reactors is a critical area in materials science research. These reactors operate under severe environments, including high temperatures, corrosion, stress, and irradiation damage. Consequently, there is a need for innovative alloy systems to ensure the reliability and longevity of proposed Generation IV reactor components. Refractory multi-principal-element alloys (RMPEA) have emerged as a promising candidate due to their exceptional properties. These alloys, characterized by their composition of multiple principal elements in near-equiatomic ratios, exhibit superior resistance to irradiation damage, reduced void swelling, enhanced microstructural stability, and minimal irradiation-induced hardening. While initial studies on RMPEAs have shown promising results, most research has been limited to thin films, nanocrystalline microstructures, and ion irradiation, which do not accurately represent the behavior of bulk materials. To address this gap, our research focused on the neutron irradiation of bulk RMPEAs. We aim to conduct comprehensive post-irradiation examinations (PIE) of RMPEAs irradiated at the Advanced Test Reactor at Idaho National Laboratory. The RMPEAs were synthesized using spark plasma sintering (SPS) with mechanically alloyed metallurgical powder. The RMPEA specimens are a MoNbTi alloy system with additions of -Zr, and -ZrV. Furthermore, PIE consisted of mechanical testing and advanced materials characterization. The mechanical testing consisted of sub-sized tensile testing, micro- and nano- indentation. Microstructural characterization included scanning electron microscopy and transmission electron microscopy. Mechanical testing coupled with advanced microscopy techniques provides insight into phase morphology and its effects on the mechanical properties of the RMPEA specimens. The results indicate that both pristine and irradiated RMPEA specimens exhibited brittle behavior during tensile testing, which can be attributed to their heterogeneous microstructure. The SPS manufacturing process did not include any post treatment, which resulted in a heterogeneous microstructure. Energy-dispersive X-ray spectroscopy revealed the presence of intermetallic such as laves phases within the microstructure. Specifically, Ti-rich precipitates were observed in the MoNbTi specimen, while Mo-rich precipitates were found in the MoNbTiZrV specimen. Nano-hardness testing of pristine samples showed that the laves phases exhibited higher hardness values compared to the matrix phase, suggesting that precipitate hardening is likely the dominant hardening mechanism in these specimens. The results from this work will be used to build a finite element model to predict mechanical behavior of future MPEA compositions. Thus, enabling for a streamlined approach to developing novel MPEAs for the nuclear industry.

36 - MATERIALS SCIENCE↗
DOE OSTI2020

High temperature air oxidation behavior of Hastelloy X processed by Electron Beam Melting (EBM) and Selective Laser Melting (SLM)

The microstructure and oxidation behavior of Laser Beam Melted, Electron Beam Melted and wrought Hastelloy X were studied at 950 °C in dry air, 50 h cycles, up to 1000 h. The variability of processing parameters and powder compositions strongly impacted the oxidation and spallation behavior. Finally, the alloys with high Mn and Si were associated with higher oxidation rates, finer Cr 2 O 3 grain microstructure and increased spallation was observed for the alloys with large elongated grain microstructures (aspect ratio of 10 ± 3).

36 MATERIALS SCIENCE↗
DOE OSTI2020

High-Resolution Comonomer Sequencing of Blocky Brominated Syndiotactic Polystyrene Copolymers Using 13C NMR Spectroscopy and Computer Simulations

This work demonstrates the first high-resolution comonomer sequencing of Blocky brominated syndiotactic polystyrene (sPS-co-sPS-Br) copolymers based on pentad assign- ments of the quaternary carbon region of the nuclear magnetic resonance spectrum. Copolymers containing p-bromostyrene (Br-Sty) units were prepared in matched sets using postpolymerization bromination methods carried out in the heterogeneous gel state (Blocky) and homogeneous solution state (Random). Quantitative information from the quaternary carbon spectra, heteronuclear multiple bond correlation spectroscopy, electronic structure calculations, and simulated statistically random copolymers was correlated to confirm the carbon resonance assignments for all 20 possible pentad comonomer sequences. Using the experimental pentad sequence prevalences, a computer code was developed to simulate chains with microstructures typical of each sample as a means to visually represent the copolymer blockiness with quantitative precision. Based on the microstructure and distribution of run lengths in these chains, the simulations revealed that the Blocky copolymers contain a high degree of blockiness. By comparing the run lengths in the simulated chains to the average number of styrene units in a crystalline segment of sPS (found by small-angle X-ray scattering), copolymer crystallizability was predicted. For the simulated Blocky B-21% (21 mol % Br-Sty) chain, the probability of randomly selecting a styrene unit in a crystallizable block was 25.8%, while that in the simulated Random R-18% was zero, in excellent agreement with the experimental crystallization behavior measured by differential scanning calorimetry. Additionally, these predictions confirmed that the simulated chains accurately represent the ensemble of chains in their respective copolymer samples. Furthermore, each simulated Blocky chain contained one or more long sPS blocks that paralleled the measured 38-40 styrene units spanning a crystalline segment within the sPS/CCl4 gel. This finding affirmed that the long sPS segments originated from the precise lamellar structure within the heterogeneous gel morphology (i.e., block length is correlated with lamellar thickness). Overall, the ability to tailor the copolymer microstructure through control of the semicrystalline gel morphology opens the door to synthesizing ordered copolymers by postpolymerization functionalization processes with unprecedented levels of compositional control.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Variations in Creep Performance of P92 Steel Within Its Composition Range: Influence of N Solubility

Underspecified composition ranges often lead to alloys with unpredictable mechanical performance. To better understand the changes in microstructure and mechanical performance associated with variations of key elements, three versions of P92 are formulated within, or close to, the specified allowable for N, B, and C ranges. Chromium and Si are also varied to influence N solubility. Different service conditions (i.e., temperature and stress) are explored. It is observed that >80% decrease in creep life occurs at 625 °C and 155 MPa for the highest B and N containing alloy. Multiscale characterization reveals key changes due to the trace element variation. The high B and N containing alloy forms deleterious BN precipitates with morphology that promotes crack nucleation and damage accumulation, but this alloy additionally forms higher fractions of beneficial MX precipitates. The alloy with the lowest B and N concentrations but greater C content shows the best creep performance—a consequence of the refined M 23 C 6 carbide precipitate population and the absence of large-scale inclusions or BN precipitates. Calculations of creep activation energy reveal that the high B and N containing alloy is more prone to damage accumulation which causes an early onset of accelerating creep and greater minimum creep rate.

36 MATERIALS SCIENCE↗