Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “composite matrix”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Impact of selenium addition to the cadmium-zinc-telluride matrix for producing high energy resolution X-and gamma-ray detectors

Abstract Both material quality and detector performance have been steadily improving over the past few years for the leading room temperature radiation detector material cadmium-zinc-telluride (CdZnTe). However, although tremendous progress being made, CdZnTe still suffers from high concentrations of performance-limiting defects, such as Te inclusions, networks of sub-grain boundaries and compositional inhomogeneity due to the higher segregation coefficient of Zn. Adding as low as 2% (atomic) Se into CdZnTe matrix was found to successfully mitigate many performance-limiting defects and provide improved compositional homogeneity. Here we report record-high performance of Virtual Frisch Grid (VFG) detector fabricated from as-grown Cd 0.9 Zn 0.1 Te 0.98 Se 0.02 ingot grown by the Traveling Heater Method (THM). Benefiting from superior material quality, we achieved superb energy resolution of 0.77% at 662 keV (as-measured without charge-loss correction algorithms) registered at room temperature. The absence of residual thermal stress in the detector was revealed from white beam X-ray topographic images, which was also confirmed by Infra-Red (IR) transmission imaging under cross polarizers. Furthermore, neither sub-grain boundaries nor their networks were observed from the X-ray topographic image. However, large concentrations of extrinsic impurities were revealed in as-grown materials, suggesting a high likelihood for further reduction in the energy resolution after improved purification of the starting material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Strain hardening magnesium-silicate-hydrate composites (SHMSHC) reinforced with short and randomly oriented polyvinyl alcohol microfibers

Magnesium-silicate-hydrate (M-S-H) cement has emerged as an alternative binder with potentially lower energy requirements and emissions. Due to the intrinsically low pH values of its matrix, however, normal steel reinforcement is not appropriate for M-S-H system. To toughen the matrix and to overcome the brittle nature of the material, a new strain hardening magnesium-silicate-hydrate composite (SHMSHC) is developed for the first time by incorporating 2 vol% short and randomly oriented polyvinyl alcohol (PVA) microfibers. The resulting SHMSHC exhibits significant strain hardening with a tensile strain capacity of more than 3%, a compressive strength beyond 50 MPa and a tensile strength of around 3 MPa. Remarkably, saturated multiple cracking with a tight crack width less than 10 μm invisible to the human naked eyes was observed. The newly developed SHMSHC addresses the fundamental challenge of M-S-H binder and is expected to widen possible application areas of M-S-H system.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multiple Stream Low-Cost Recycling Method

The global composite industry generates large quantities of waste and which mostly end as landfill due to lack of meaningful end-use applications for the multiple waste streams. In a recent report by the Electric Power Research Institute (EPRI), waste generated by the wind industry could reach 370,000 tons a year of composite wind energy blades being decommissioned and scrapped. Wind energy is just one major industry utilizing composite materials. The waste generated by industry includes End-of-Life (EoL) materials and manufacturing process scrap. GreenTex Solutions has developed a unique and innovative technology to recycle the composite waste streams in a range of forms made from production waste and EoL materials. This includes manufacturing waste materials such as dry chopped fiber tow, loose fibers, shredded fibers from reinforcement fabrics, cured/semi-cured prepregs, and it also includes fully-cured composite structure waste (such as edge trims from cured parts) from manufacturing aircraft, automobiles, wind blades, boats, and composite cylinders (tanks). Current recycling methods involve recovering the structural fiber by removing the matrix resin through methods such as pyrolysis. The resulting fibers are used in injection molding or wet laid nonwoven mats and other usable forms. The GreenTex technology bypasses these intermediate steps to create the lowest possible recycling processing costs and the lowest embodied energy/CO2 emissions. The end-product from the GreenTex technology is a finished industrial composite part/application versus intermediate fibers or fabrics. The GreenTex manufacturing process enables cross-industry reuse of recycled feedstock by taking waste from multiple industries (wind energy, aerospace, marine, etc.) and recycles the waste into a product used in other industries. The initial target market application is structural flooring for intermodal shipping containers and truck bodies. One of the team’s key partners is Wabash National which produced 29,000 truck bodies in 2019. The current flooring system is comprised of solid oak “butcher board” laminated panels. Additionally, Mediterranean Shipping Containers (MSC) transports over 1.8 million twenty-foot equivalent units per year in intermodal shipping containers. The current container floor is laminated hardwood that is harvested from the rain forests of Central and South America. The project is to develop a flooring system made from recycled composites that can be qualified for both companies (Wabash and MSC). Initial prototypes validated that the recycled composites panels are lighter and thinner with much higher mechanical strength. These results suggest a typical truck trailer would have 20% lower tare weight. The GreenTex technology is not limited to flooring and is widely applicable to other transportation elements such as walls, roof elements, cab areas and related structural components. Under this project different composite waste streams were evaluated and then combined to develop a formulation that would meet the targeted performance criteria for a flooring system. Wet compression molding was used to fabricate plaques at different tonnage using various composite waste streams. The plaques were tested for flexure and impact.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Alpha-Imaging Detector System Development for Large Area Monitoring

Effective management and disposal of legacy nuclear waste are essential for ensuring safe work environments and minimizing environmental impacts. Monitoring airborne actinide contamination is particularly critical due to the high internal dose potential of alpha-emitting radionuclides. Traditional continuous air monitoring systems (CAMs) used in the industry are limited in the volume of air they can sample, potentially leading to inaccurate radiation detection over large areas. For example, in 2018, elevated levels of airborne Plutonium-239 were detected beyond the controlled areas of the Hanford Plutonium Finishing Plant, highlighting the potential risks to both plant workers and nearby residents. To address these challenges, high-efficiency particulate absorbing (HEPA) air purifiers can enhance air flow by up to 1.5 orders of magnitude, thereby increasing monitoring efficiency and providing a cost-effective solution for large-area surveillance. To quantify the activities of alpha-emitting radionuclides on HEPA filters, the Savannah River National Laboratory is developing an advanced alpha-imaging detection system. This system includes scintillating materials combined with a digital scientific camera. A significant concern in operating such a large-area airborne monitoring system is the handling of HEPA filters, which may be contaminated with radioactive particles. To mitigate these hazards, it is crucial to ensure that any contamination is securely fixed onto the filters. Efforts have been made to optimize the sensitivity of scintillator-epoxy composites and apply them to HEPA filters. These materials were characterized using fluoroscence spectroscopy. These techniques confirmed the purity of the raw materials, the dispersion of scintillators in the epoxy matrix, and the stability of their optical and structural properties post-modification. The optimal scintillator-epoxy composite was selected for use on alpha-spiked HEPA filters to evaluate the efficiency of the sprayer. HEPA filters, embedded with alpha particles collected by an air purifier deployed in an airborne radiation area, have been tested to assess detection efficiency. Future work will focus on employing multiple imaging sensors simultaneously to enhance sensitivity across different regions of the HEPA filter.

Pham, Phuong [Savannah River National Laboratory (↗
DOE OSTI2021

An Atom Probe Tomography Study of the Through Wall Attenuation Effect on Cu-rich Precipitate Formation in a Reactor Pressure Vessel Steel

In this study, high-Cu weld material harvested from an ex service reactor pressure vessel (RPV) steel from Unit 1 of the decommissioned Zion Nuclear Generating Station has been characterized using atom probe tomography. Samples taken from 4 different positions through the thicknesses of the pressure vessel wall from the water-side to the air-side were characterized, along with an unirradiated baseline material. In the baseline material, no precipitates were found and the Cu was observed to be fully in solid solution; however, scanning transmission electron microscopy combined with energy dispersive spectroscopy (STEM-EDS) revealed the presence of ϵ -Cu that form during processing of the material and results in the concomitant decrease of matrix Cu. Following irradiation, a high number density of nano-scale Cu-rich precipitates (CRPs) were observed, uniformly distributed throughout the matrix. The Cu content within the CRPs was found to be ~30-35 at.% regardless of location in the wall. No statistically significant variation in the compositions, mean radius, number density, or volume fraction as a function of location within the wall was observed. The measured matrix Cu level excluding CRPs contribution was found to be ~90 appm higher than the solubility limit suggesting that further nucleation and growth of the CRPs under continued operations would have occurred. These results clearly demonstrate that the neutron energy attenuation has no significant effect on the precipitation kinetics of CRPs regardless of location in the wall in high-Cu RPV steels under irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Polyacrylonitrile Composites of Ag–Al–Si–O Aerogels and Xerogels as Iodine and Iodide Sorbents

Mechanically robust engineered sorbents were constructed by embedding Ag-loaded aerogels or xerogels in a polyacrylonitrile (PAN) matrix at 30 or 50 mass% loadings of gel in PAN. Here, the process for making the base gels as well as the composite materials is described herein, a technology that is very flexible for making hybrid sorbents using various inorganic or organic active sorbents. The PAN-gel composite materials were evaluated for iodine uptake in the form of gaseous iodine [I 2(g) ] at room temperature and at 150°C as well as iodide (I – ) at room temperature from simulated liquid nuclear wastes. The composites show high I 2(g) uptake and high I – uptake (= 93 mass%) in simulated liquid secondary waste spiked with 5 mg L -1 I – . These results demonstrate the utility of such a composite form for iodine removal from contaminated gas and liquid streams.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Recyclable Cellulose Fiber Reinforced Vitrimer Composite

Vitrimer is an innovative class of polymeric materials which demonstrates traditional thermoset-like mechanical and chemical resilience while still being able to flow on demand like a traditional thermoplastic through covalently adaptive dynamic linkages. Herein, high-performance cellulose fiber reinforced vitrimer composites are developed using an epoxy-based vitrimer and natural cellulose paper. The reinforced vitrimer composite was fabricated by impregnating the porous structure of cellulose paper with two curable monomers, followed by in-situ polymerization of the monomers inside the fibrous scaffold. The introduction of hydroxyl group present on the cellulosic framework assisted in a faster topological rearrangement of the crosslinked matrix through transesterification exchange reaction, thus imparting various sought-after properties like shape recovery and recyclability via simple thermal reprocessing. Moreover, the reinforced vitrimer composite exhibits superior tensile properties as high as 90 MPa with 15-25 volume% vitrimer loading due to the interfacial adhesion via ester exchange reaction between the epoxy matrix and functionalities on the cellulosic fibers. Noteworthily, the key ingredients of the resulting composite (i.e., epoxy-based vitrimer and cellulose fibers) can be comfortably recycled without using aggressive chemical treatment, enabling composite to be easily recycled or disposed of at the end of service life and assist in reducing the subsequent manufacturing cost. This study would shed light on the development of a recyclable polymer composite with exceptional mechanical properties while simultaneously demonstrating self-healing and shape memory capabilities.

Rohewal, Sargun Singh↗
DOE OSTI2024

Effects of mercerization and fiber sizing of coir fiber for utilization in polypropylene composites

The use of natural fibers as an alternative to synthetic fibers for reinforcing composites is increasing. However, the poor interfacial adhesion between natural fibers and polymer matrices limits their applications. Several approaches have been considered to improve fiber-matrix adhesion via chemical and/or physical treatment. However, the effectiveness of these treatments varies based on the type of fiber, its source, and its composition. Thus, it is imperative to understand the effectiveness of treatment conditions. In this study, we investigated the influence of alkali treatment and fiber sizing on the chemical, thermal, morphological, and mechanical properties of coir fibers and the interface between coir fiber and polypropylene matrix. Further, it was found that using a 5 wt% sodium hydroxide solution for 6 h at room temperature was the optimal treatment condition that led to an improvement in tensile strength by 58%, tensile modulus by 71%, and elongation at break by 37% compared to untreated fibers, and an increment in interfacial shear strength (IFSS) between coir fibers and polypropylene matrix by 32%. The alkali treatment removed the fiber surface impurities, made the fiber surface rough, and enhanced the fiber crystallinity. Sizing of the alkali-treated fiber led to an improvement in IFSS by 87% with no modification of the fiber’s mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Melt compounding of spray-dried cellulose nanofibrils/polypropylene and their application in 3D printing

Abstract Micro- and nano-scale cellulosic fillers exhibit excellent dispersion and distribution within a thermoplastic matrix during the process of melt compounding or injection molding. In this study, spray-dried cellulose nanofiber (SDCNF) powders were manufactured using a pilot-scale rotating disk atomizer spray dryer. Bleached Kraft pulp (BKP), unbleached Kraft pulp (UKP), and old corrugated cardboard pulp (OCC) fibrillated at a fines level of 90% were used as feedstock materials for spray-drying. BKP-, UKP-, and OCC- SDCNFs were compounded with polypropylene using a twin screw co-rotating extruder. Maleic anhydride grafted polypropylene (MAPP) was used as a coupling agent in the composite formulations. The tensile, flexural, and impact properties of SDCNF-filled PP composites increased at 10 wt% SDCNF loading. The presence of SDCNFs in the PP matrix resulted in faster crystallization and a 12% reduction in the degree of crystallinity of the neat PP. The coefficient of thermal expansion (CTE) of neat PP was reduced by up to 31% attributable to the presence of the SDCNFs. Application of the SDCNF-reinforced PP composites in 3D printing reduced the shrinkage rate of the printed neat PP by 39%, and the printability of the PP was significantly improved with the addition of the SDCNFs.

Materials Science↗
DOE OSTI2021

Design and Gas Separation Performance of Imidazolium Poly(ILs) Containing Multivalent Imidazolium Fillers and Crosslinking Agents

This work introduces a series of vinyl-imidazolium-based polyelectrolyte composites, which were structurally modified via impregnation with multivalent imidazolium-benzene ionic liquids (ILs) or crosslinked with novel cationic crosslinkers which possess internal imidazolium cations and vinylimidazolium cations at the periphery. A set of eight [C4vim][Tf2N]-based membranes were prepared via UV-initiated free radical polymerization, including four composites containing di-, tri-, tetra-, and hexa-imidazolium benzene ILs and four crosslinked derivatives which utilized tri- and tetra- vinylimidazolium benzene crosslinking agents. Structural and functional characterizations were performed, and pure gas permeation data were collected to better understand the effects of “free” ILs dispersed in the polymeric matrix versus integrated ionic crosslinks on the transport behaviors of these thin films. These imidazolium PIL:IL composites exhibited moderately high CO2 permeabilities (~20–40 Barrer), a 4–7× increase relative to corresponding neat PIL, with excellent selectivities against N2 or CH4. The addition of imidazolium-benzene fillers with increased imidazolium content were shown to correspondingly enhance CO2 solubility (di- < tri- < tetra- < hexa-), with the [C4vim][Tf2N]: [Hexa(Im+)Benz ][Tf2N] composite showing the highest CO2 permeability (PCO2 = 38.4 Barrer), while maintaining modest selectivities (αCO2/CH4 = 20.2, αCO2/N2 = 23.6). Additionally, these metrics were similarly improved with the integration of more ionic content bonded to the polymeric matrix; increased PCO2 with increased wt% of the tri- and tetra-vinylimidazolium benzene crosslinking agent was observed. This study demonstrates the intriguing interactions and effects of ionic additives or crosslinkers within a PIL matrix, revealing the potential for the tuning of the properties and transport behaviors of ionic polymers using ionic liquid-inspired small molecules.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Textile-Grade Carbon Fiber-Reinforced Polycarbonate Composites: Effect of Epoxy Sizing

In this work, epoxy-sized textile-grade polyacrylonitrile (PAN) carbon fiber (TCF) with 450 K filaments (CFTF, ORNL) was reinforced in the polycarbonate (PC) matrix using a compression molding technique. The epoxy sizing effect on the surface, thermal, and mechanical properties of TCF–PC was investigated. X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy results of the TCF–PC composite show the absence of an oxirane group (epoxy-sized TCF), which suggests a covalent bond formation between the oxirane ring and carbonyl groups from TCF and PC. Dynamic mechanical analysis results confirm a strong immobilized interface (b > 1) present between TCF and PC. The tensile, flexure, compression, and interlaminar shear strength of TCF–PC composites were 323 ± 53, 371 ± 31, 397 ± 87, and 36 ± 3 MPa, correspondingly. The fracture analysis through scanning electron microscopy shows good wettability between TCF and the PC matrix which validates the results obtained from surface and thermal characterization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Evaluating Effects of Shear Processing on 2D Crystalline Materials in 3D Metal Matrices: Atomistic Understanding of High Shear Deformation of Copper Graphene Composites

Composites made of copper and graphene demonstrate high strength, lubricity and enhanced electrical and thermal conductivity compared pure copper. However, manufacturing these composites at bulk volumes for industrial applications has been a big challenge. Shear deformation assisted processing is an effective method for manufacturing materials such as copper-graphene composites demonstrating ultra-fine grain structures and compositional homogeneity. Nevertheless, microstructural evolution of the composites and their property development under such conditions is not clearly understood currently. To rectify this gap in literature, high strain shear deformation of copper coated graphene foils was performed using a tribometer pin in this study. Changes in microstructure of the composite as well as the constituent components under shear deformation was correlated to process conditions. A sharp increase in the coefficient of friction attributed to rupture and smearing of graphene layer into copper substrate was observed during the shear processing. The coefficient of friction of the sheared copper/graphene composite was lower than that of pure copper, suggesting that partially worn graphene is effectively lubricious at the macroscale. A multimodal characterization of the processed region further revealed a shear deformation-induced ultrafine two-phase grain-structure consisting of copper and graphitic domains. Shear deformation reduced the copper grain size from around 50 – 100 µm to ~200 nm on an average and ~2 – 5 nm in some locations. The semicrystalline graphene films were observed to fracture into 10 – 50 µm size flakes. Oxygen enrichment was observed in the processed region. Finally, graphitic domain were identified for the first time in the copper matrix and not just at the grain boundaries providing evidence for a metastable composite microstructure as a result of solid phase processing at room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A de novo matrix for macroscopic living materials from bacteria

Engineered living materials (ELMs) embed living cells in a biopolymer matrix to create materials with tailored functions. While bottom-up assembly of macroscopic ELMs with a de novo matrix would offer the greatest control over material properties, we lack the ability to genetically encode a protein matrix that leads to collective self-organization. Here we report growth of ELMs from Caulobacter crescentus cells that display and secrete a self-interacting protein. This protein formed a de novo matrix and assembled cells into centimeter-scale ELMs. Discovery of design and assembly principles allowed us to tune the composition, mechanical properties, and catalytic function of these ELMs. This work provides genetic tools, design and assembly rules, and a platform for growing ELMs with control over both matrix and cellular structure and function.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Annual report for DOE VTO

Carbon fiber (CF)/polymer composites are a transformative class of high-performance, lightweight material, where high aspect-ratio CFs reinforce a polymer matrix and exceed the strength of steel alloys at a fraction of the density. Despite the advantages of such a class of material, the broader implementation of CF composites in a range of automotive, aerospace, and energy applications is hindered by limitations of current manufacturing methods. These current techniques (e.g., hand lay-up, wet filament winding) are costly and impose severe limitations on fiber placement, orientation, and angle, and thus a composite’s ultimate properties. Today’s CF composites are expensive to manufacture, limited in form factor, and utilize costly and sub-optimal continuous filament CF. Advanced additive manufacturing (AM) processes, combined with computational design optimization and new approaches to resin development, offer alternative design and manufacturing paradigms that have the realistic potential to lift these constraints. Such integrated AM approaches could thus help to realize the full potential of CF composite materials. One relevant application of CF composite materials where manufacturing constraints limit the cost-benefit ratio is in the manufacture of high-performance composite pressure vessels for onboard compressed natural gas (CNG) storage. Current CNG storage vessels (Types 3–5) are made from load-bearing filament-wound carbon-fiber composite and are ~3.5 times as expensive as an all-metallic Type-1 vessel. This cost is invariably tied to the complex and labor-intensive nature of conventional filament winding processes and the large volumes of expensive high tensile-strength CF tow feedstock required in manufacture. Our proposed approach to CNG storage vessel manufacture is based on a combination of AM technologies for CF composite printing and design optimization tools that were pioneered at Lawrence Livermore National Laboratory (LLNL), with advances in resin/composite formulation enabled by chemical and nano-material modification. Through the successful development of this technology, LLNL seeks to demonstrate the capability for advanced CNG storage vessel manufacture at reduced cost with no reduction in performance versus the most advanced, extant Type-5 designs.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Effects of processing temperature, pressure, and fiber volume fraction on mechanical and morphological behaviors of fully-recyclable uni-directional thermoplastic polymer-fiber-reinforced polymers

This work explores a type of composite called thermoplastic polymer-fiber-reinforced polymers (PFRPs), often referred to as self-reinforced composites (SRCs). A representative PFRP was exemplified using unidirectional (UD) ultra-high-molecular-weight polyethylene (UHMWPE) fibers embedded in a high-density polyethylene (HDPE) matrix. The effects of compression molding temperature and pressure on the mechanical and morphological behaviors of the filament-wound PFRPs with various fiber volume fractions (V f ) were experimentally investigated. The results elucidate the evolution of morphologies and tensile properties of the PFRPs due to thermal melting, fiber misalignment from pressure, and (V f )-induced structural variance, which has not been comprehensively reported yet. The highest specific tensile strength and modulus of the PFRP laminae reach 600 MPa/(g/cm 3 ) and 31 GPa/(g/cm 3 ), respectively. These properties are comparable to glass-/aramid-fiber-reinforced polymers (GFRPs, GFRTPs, AFRPs, and AFRTPs), with PFRPs exhibiting better ductility (specific strain at peak load ≈ 4%/(g/cm 3 )) than other common polymer composites. The motivation for this work was the high recyclability of PFRPs, which can be recycled by melting both the fibers and the matrix, and then reshaped them for re-manufacturing composites to maximize the efficiency in material reuse. This process simplifies the implementation of closed-loop recycling, re-manufacturing, and reuse to support sustainability in composites. This work aims to contribute to advancing thermoplastic PFRPs for their potential applications in various industries.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Compositionally graded aluminum-silicon alloy fabricated via friction extrusion

Herein, a novel solid-phase gradient alloying technique was developed for a high throughput composition-microstructure-mechanical property assessment. Friction extrusion of a two-piece billet setup facilitated the formation of a seamless compositionally graded aluminum (Al)-silicon (Si) extrudate rod, with Si concentration in Al matrix gradually increasing from ~1 at% at one end to ~7 at% at the other end of the rod. We observed a strong dependence of the Al grain size, morphology, and texture on the Si concentration. The Si particles pinned the recrystallized grain boundaries resulting in refined (< 10 µm) and textured grains in the high Si content region, while the Al grains in the low Si region are equiaxed, randomly textured, and with a larger average size (~50 µm). The hardness of Al-Si gradient extrudate increases by ~50% percent with a 6 at% increase in Si content due to Hall Petch and particle strengthening effects. Our approach demonstrates the use of a solid phase processing technique to successfully produce a defect-free continuously compositionally graded bulk components thus overcoming the limitations of porosity and material heterogeneities commonly observed in other techniques such as by additive laser deposition.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tailoring capping-layer composition for improved stability of mixed-halide perovskites

Incorporating a low dimensional (LD) perovskite capping layer on top of a perovskite absorber, improves the stability of perovskite solar cells (PSCs). However, in the case of mixed-halide perovskites, which can undergo halide segregation into single-halide perovskites, a systematic study of the capping layer's effect on mixed-halide perovskite absorber is still lacking. This study bridges this gap by investigating how the 1D perovskite capping layers on top of MAPb(I x Br 1–x ) 3 (x = 0, 0.25, 0.5, 0.75, 1) absorbers affect the films' stability. We utilize a new method, dissimilarity matrix, to investigate the image-based stability performance of capping-absorber pair compositions across time. This method overcomes the challenge of analyzing various film colors due to bandgap difference in mixed-halide perovskites. We also discover that the intrinsic absorber stability plays an important role in the overall stability outcome, despite the capping layer's support. Within the 55 unique capping-absorber pairs, we observe a notable 1D perovskite material, 1-methoxynaphthalene-2-ethylammonium chloride (2MeO–NEA–Cl or 9-Cl), that improves the stability of MAPbI 3 and MAPb(I 0.5 Br 0.5 ) 3 by at least 8 and 1.5 times, respectively, compared to bare films under elevated humidity and temperature. Surface photovoltage results also show that the accumulation of electrostatic charges on the film surface depends on the capping layer type, which could contribute to the acceleration/deceleration of degradation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗