Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “breakdown”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Numerical analysis of air dehumidification through electrospray-enhanced vortical flow cyclone separator

The dehumidification of air is a highly energy-intensive process, typically requiring vapor compression systems to cool the air significantly below its dew point temperature. Here, this study numerically investigates air dehumidification achieved by electrostatic and dielectrophoresis forces in a converging duct and centrifugal principles in cyclone separators. An electrospray was employed to energize water droplets, which then captured water vapor via dielectrophoresis. A novelty of the present study is the inclusion of a cyclone separator positioned downstream of the electrospray. This combination increased the dehumidification efficiency and controlled the flow of the condensate. By integrating electrospray technology and applying an electric field, this study examines the impact of particle separation efficiency, pressure drops, and cyclone performance on air dehumidification. The control parameters for air dehumidification were investigated. Three cyclones were modelled for airflow rates of 5 cubic feet per minute [cfm] (0.0024 m 3 /s), 38 cfm (0.0179 m 3 /s), and 200 cfm (0.094 m 3 /s). The results indicated air dehumidification was up to 5.7 % under environmental conditions, similar to those used to validate the CFD model. The degree of air dehumidification was primarily influenced by the electric charge acquired by the water droplets, their flight trajectory, and the vorticity intensity within the cyclone. Air dehumidification could increase by up to 13 % by increasing the number of droplets injected into the air stream, the flight time, and the electrical charge. The breakdown electric field strength threshold near the electrospray was a limiting factor for further enhancing dehumidification performance. This study examines the optimization of an electro-assisted dehumidification system that includes cyclone-based droplet separation through numerical analysis. The results provide insights into the design of energy-efficient air treatment technologies.

42 ENGINEERING↗
DOE OSTI2026

Metal additively manufactured wavy fin cold-plate architecture for improved thermal-hydraulic performance

Rapid growth in artificial intelligence and data center workloads demands high-performance liquid cooling to manage increasing chip power. This study presents two metal-additive-manufactured cold plates with sinusoidal fins, constant-amplitude wavy fins and linearly variable-amplitude wavy fins and compares them against metal-additive-manufactured straight fins using experiments conducted at 1 kW heat dissipation as well as high-fidelity 3D conjugate computational fluid dynamic simulations. The cold plates were printed in AlSi10Mg material and underwent design using a Python-automated workflow prior to manufacture and testing. The experiments show that wavy fins reduce the normalized thermal resistance by 35 to 45 % at water flow rates from 1 to 4 LPM. At a fixed 20 kPa pressure drop, the variable-waviness design lowered peak surface temperature by 9 °C and thermal resistance by 51 %, while edge-channel maldistribution in the constant wavy fin design limited gains. A thermal resistance breakdown revealed that 55–63 % of the total thermal resistance in wavy designs comes from base heat conduction, 27–33 % from fin heat conduction, and 9–13 % from fin heat convection, indicating the need to address conduction bottlenecks. Parametric sweeps identify a 3 mm fin pitch as optimal, and that horizontal inlet/outlet manifolds further reduce pressure drop by 30–60 % and thermal resistance by 9–16 % relative to vertical inlet-outlet manifolds. The results yield comprehensive guidelines for fin geometry, manifold alignment, material selection and additive-manufacturing constraints to realize high-performance liquid-cooled cold plates for power-dense electronics.

3d printing↗
DOE OSTI2020

Automotive fuel cell stack and system efficiency and fuel consumption based on vehicle testing on a chassis dynamometer at minus 18 °C to positive 35 °C temperatures

In this work we present an in-depth laboratory technology assessment of a 2016 Toyota Mirai Fuel Cell (FC) vehicle based on chassis dynamometer testing. The 114.6 kW FC stack has a high dynamic response, which makes this powertrain a FC-dominant hybrid electric vehicle. The measured peak efficiency is 66.0% FC stack and 63.7% FC system with an idle hydrogen flow rate of 4.39 g/hr. The high FC system efficiencies at low loads match typical vehicle power spectrums, resulting in a high average vehicle efficiency of 62% compared to 45% and 23% for a hybrid electric vehicle and a conventional vehicle, respectively. An energy breakdown accounts for the FC stack losses, FC system losses, air compressor loads, and heater loads for different drive cycles and different thermal conditions. The cold-start North American city drive cycle (UDDS) energy consumption values are, respectively, 758, 581, 226, and 321 Wh/km at ambient conditions of -18 degrees C, -7 degrees C, -25 degrees C and 35 degrees C with 850 W/m 2 of solar loading. The FC system shutdown and startup processes at temperatures below the freezing point contribute to the increased hydrogen consumption. Additionally, the raw test data files are available for download, thus providing the research community with a public reference data on a modern production automotive FC system.

08 HYDROGEN↗
DOE OSTI2021

Hydroxide melt induced corrosion of Ni at elevated temperatures under steam electrolysis conditions

Molten alkali electrolyte based high temperature water electrolysis (HTWE) process offers an efficient pathway to integrate renewable energy resources for large scale and economic hydrogen production. Long term and stable operation of these systems require an in-depth understanding of materials stability under anodic and cathodic exposure conditions of the cell and cell stacks. In the present study, we report our findings on the corrosion of Ni in the presence and absence of (LieNa) hydroxide melt at 600 °C under oxidizing and reducing conditions representative of HTWE. While the Ni electrode was found to remain thermodynamically stable in metallic form under cathodic (reducing) exposure conditions, the corrosion rate in molten hydroxide under oxidizing conditions was found to be nonparabolic in nature. A cyclic voltammetry study provides the breakdown of the passive metal-oxide surface layer at the anodic overpotential region between 0.45 V and 2 V in molten hydroxide under oxidizing conditions. As a result, a thermochemical process for accelerated corrosion based on the oxide scale fluxing in hydroxide melt has been developed.

08 HYDROGEN↗
DOE OSTI2022

Hedging direct simulation Monte Carlo bets via event splitting

We propose a new scheme for simulation of collisions with multiple possible outcomes in variable-weight DSMC computations. The scheme is applied to a 0-D ionization rate coefficient computation, and 1-D electrical breakdown simulation. We show that the scheme offers a significant (up to an order of magnitude) improvement in the level of stochastic noise over the usual acceptance-rejection algorithm, even when controlling for the slight additional computational costs. Furthermore, the benefits and performance of the scheme are analyzed in detail, and possible extensions are proposed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

The detrimental ratio ( ρ ): A critical metric complementing coulombic loss for long calendar-life silicon-based lithium-ion batteries

Silicon (Si) is a promising high-capacity anode in lithium-ion batteries but suffers from chronic chemical degradation and capacity fading during calendar aging, greatly hindering its automobile applications. Electrolyte engineering currently relies on conventional evaluation criteria of reducing coulombic consumption, which implicitly presume its equivalence to irreversible capacity loss and complicates battery development. Here, we introduce the detrimental ratio p to quantify the fraction of parasitic species that permanently degrades active material. This metric is independent and crucially complements total coulombic consumption for accurate performance evaluation. We systematically investigate multiple electrolyte formulations using high-precision leakage current measurements, open-circuit-voltage experiments, and post-mortem characterizations. Although some electrolytes exhibit similarly low coulombic consumption, they diverge significantly incapacity retention and p. Especially, dimethyl-carbonate-based localized-high concentration electrolyte can synergically achieve low coulombic consumption and detrimental ratio p during calendar aging, owing to its chemically inert and structurally resilient solidelectrolyte interface with minimal isolated Si material. By contrast, increasing fluoroethylene carbonate (FEC) additive content suppresses electrolyte breakdown but suffers aggravated chemical degradation of more LixSi isolation for irreversible capacity loss with arising p. This study critically reveals that the chemistry-characteristic detrimental ratio p establishes physically informed performance evaluation to pave the way for accelerating battery development.

Calendar aging↗
DOE OSTI2025

Enhancing low-temperature sintering in the MgO-LiF system: Mechanistic insights

In the present article, we provide compelling evidence that minor (1 wt%) additions of micron and nanometre-sized LiF particles in MgO decompose leading to free Li diffusing into MgO surfaces enhancing vacancy production during direct current sintering. The addition of nanometre-sized LiF particles leads to a > 500 °C reduction in the sintering temperature and over 99 % theoretical density of final consolidated compacts. Correlating differential scanning calorimetry with in-situ x-ray diffraction, together with Schottky calculations, post sintering electron microscopy and laser induced breakdown spectroscopy, we uncover critical insights into this impressive reduction in sintering temperature. Our quantitative analysis reveals that MgO and LiF interact at low temperatures with the diffusion of Li into the surface of MgO particles due to the intrinsic structural disorder of the LiF and MgO crystallites. Nanometre-sized LiF particles were found to react the most at low temperatures due to their increased structural disorder. Our multimodal characterization points to a Li-promoted densification and sintering mechanism. This impressive reduction in sintering temperature can be harnessed to promote low-temperature fabrication of MgO-based composites for technological applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microbial interactions with phosphorus containing glasses representative of vitrified radioactive waste

The presence of phosphorous in borosilicate glass (at 0.1 – 1.3 mol % P 2 O 5 ) and in iron-phosphate glass (at 53 mol % P 2 O 5 ) stimulated the growth and metabolic activity of anaerobic bacteria in model systems. Dissolution of these phosphorous containing glasses was either inhibited or accelerated by microbial metabolic activity, depending on the solution chemistry and the glass composition. The breakdown of organic carbon to volatile fatty acids increased glass dissolution. The interaction of microbially reduced Fe(II) with phosphorus-containing glass under anoxic conditions decreased dissolution rates, whereas the interaction of Fe(III) with phosphorous-containing glass under oxic conditions increased glass dissolution. Phosphorous addition to borosilicate glasses did not significantly affect the microbial species present, however, the diversity of the microbial community was enhanced on the surface of the iron phosphate glass. Results demonstrate the potential for microbes to influence the geochemistry of radioactive waste disposal environments with implication for wasteform durability.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Cobalt Dissolution from Metal Oxides and Battery Cathode Materials with Acetic Acid-Based Deep Eutectic Solvents

Recovery of critical metals with alternative solvents beyond those in traditional pyrometallurgy and hydrometallurgy is needed in consideration of environmental challenges and the growing demand for metals in energy technologies. Deep eutectic solvents (DESs) have emerged as sustainable alternatives for solvometallurgy in metal separation and recovery. In this study, DESs based on hydrogen bond acceptors (HBAs) including choline chloride (ChCl), acetylcholine chloride (AChCl), and betaine (Bet) were investigated for their effectiveness when paired with acetic acid (AA) as the hydrogen bond donor (HBD) for the dissolution of cobalt from cobalt oxide (CoO), lithium cobalt oxide (LiCoO 2 ), and lithium nickel manganese cobalt oxide (LNMC). Based on the spectroscopic analysis of the metal dissolution and coordination, Bet:AA was found to provide the highest solubility for CoO (0.33 M) in the form of an octahedral complex. On the other hand, ChCl:AA solvent was more effective at dissolving LiCoO 2 with 0.04 M Co 2+ corresponding to 17% dissolution efficiency and LNMC with 0.06 M Co 2+ corresponding to 72% dissolution efficiency at 50 °C, compared to Bet:AA (9% for LiCoO 2 and 31% for LNMC). Although the solubilities of LiCoO 2 and LNMC have not significantly improved in ChCl:AA, this difference in effectiveness between the solvents clearly reveals the role of the HBA in solubilization. The coordination synergy between the chloride and the –OH moiety facilitates the breakdown of the LiCoO 2 driven by the alteration of the solvent polarity. Cobalt in these solutions was found dominantly as a tetrahedral [CoCl 4 ] 2– complex. A chemical separation of cobalt oxalate from a mixed-metal oxide system based on Co, Fe, and Ni was also demonstrated, confirming the potential of these solvents for practical metal recovery.

Cobalt separation↗
DOE OSTI2022

Ab initio molecular dynamics (AIMD) simulations of NaCl, UCl 3 molten salts

Ab initio molecular dynamics (AIMD) simulations are used to calculate select thermophysical and thermodynamic properties of NaCl, UCl and NaCl-UCl 3 molten salts. Following established approaches, the AIMD simulations include a model for Van der Waals interactions. The Langreth & Lundqvist (vDW-DF2), DFT-D3, and density-dependent energy correction (DFT-dDsC) dispersion models are first tested for molten NaCl in order to assess their accuracy for density and heat capacity predictions across a range of temperatures. Based on the NaCl results, the vdW-DF2 and DFT-dDsC methods are extended to the UCl 3 system and compared to available experimental data. Next, mixtures of NaCl-UCl 3 are investigated and analyzed with respect to the deviation from ideal solution behavior. For the DFT-dDsC simulations, density deviates by up to 2% from an ideal mixture, with the maximum occurring close to the eutectic composition. The mixing energy also deviates from an ideal solution and exhibits a minimum of about -0.074 to eV per formula unit, again close to the eutectic composition. Finally, the compressibility and species diffusivity of the pure and mixed salt systems are calculated. The diffusivities are slightly reduced in the mixed compared to the pure systems and the compressibilities loosely follow a linear correlation as a function of the UCl 3 composition. The trends observed for mixing properties are rationalized by correlating them to the coordination chemistry, which emphasizes the importance of maintaining the extended network formed by U and Cl ions as the NaCl concentration increases. The concentration at which breakdown of the extended network occurs, roughly coincides with the minimum of both the mixing energy and the deviation from ideal solution behavior for density.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

The battery failure databank: Insights from an open-access database of thermal runaway behaviors of Li-ion cells and a resource for benchmarking risks

The thermal response of Li-ion cells can greatly vary for identical cell designs tested under identical conditions, the distribution of which is costly to fully characterize experimentally. The open-source Battery Failure Databank presented here contains robust, high-quality data from hundreds of abuse tests spanning numerous commercial cell designs and testing conditions. Data was gathered using a fractional thermal runaway calorimeter and contains the fractional breakdown of heat and mass that was ejected, as well as high-speed synchrotron radiography of the internal dynamic response of cells during thermal runaway. The distribution of thermal output, mass ejection, and internal response of commercial cells are compared for different abuse-test conditions, which when normalized on a per amp-hour basis show a strong positive correlation between heat output from cells, the fraction of mass ejected from the cells, their energy- and power-density. Ejected mass was shown to contain 10x more heat per gram than non-ejected mass. The causes of 'outlier' thermal and ejection responses i.e., extreme cases, are elucidated by high-speed radiography which showed how occurrences such as vent clogging can create more hazardous conditions. High-speed radiography also demonstrated how the time-resolved interplay of thermal runaway propagation and mass ejection influences the total heat generated.

25 ENERGY STORAGE↗
DOE OSTI2026

Optimizing Porous Transport Layer Porosity for Proton Exchange Membrane Water Electrolysis

An empirical model is presented that describes anode-side losses related to porous transport layer (PTL) morphology in proton exchange membrane water electrolysis (PEMWE). The model is based on an advanced voltage breakdown analysis that links various overpotentials to PTL morphology. Custom Ti PTLs, spanning uncommonly low porosities (22 - 31%), were fabricated and analyzed with X-ray CT to obtain pore and particle size distributions. Particle size distributions were consistent across samples with an average particle diameter of 12.0?..mu..m, whereas average pore diameters ranged from 6.0 to 7.0?..mu..m. The PTLs were tested in standard PEMWE cell assemblies with anode catalyst loadings of 0.1 mgIr cm-2 to obtain polarization curves, electrochemical impedance spectra, and augmented Tafel analysis. The PTL-dependent anode side losses were deconvoluted and assigned to excess utilization, concentration, ion transport resistance, and electrical contact resistance overpotentials. The data and model reveal an optimal 20 - 28% PTL porosity region where utilization and contact resistance overpotentials are minimized without triggering concentration and ion transport losses related to water deprivation. The optimal PTL porosity depends on the operating current density and is demonstrated at realistic PEMWE water flow rates to establish PTL design guidance for operation at scale.

08 HYDROGEN↗
DOE OSTI2023

Simulation of two nanoparticle melting to understand the conductivity drop of 3D-printed silver nanowires

The future flexible sensor technology will require low-temperature, fast processing 3D printing techniques that will rely heavily on the quality of nanoparticle (NP) Ink. Electrical conductivity has been found to decrease in majority of the 3D printed electronic wires. Herein we report a fundamental understanding in drop of electrical conductivity in processed silver (Ag) line wire, generally found in Ag-nanoparticle Ink, using large-scale atomistic molecular dynamics (MD) simulations of sintering of five different sizes of Ag NPs. To preserve the high conductivity of pure silver wires, the integrity of the pristine face-centered cubic (FCC) crystalline structure must be retained in the processed line wires. Simulations show that the pristine Ag FCC structures of the nanoparticles are not recovered after melting and resolidification, instead, the resolidified material is paracrystaline. The breakdown of pristine FCC structures might be the cause of the drop in conductivity of processed Ag wires. Simulation results suggest that the intermediate size nanoparticles retain highest percentage of the pristine silver face-centered cubic (FCC) structure after pulse treatments. Our results show that the most promising Ag-Ink should contain smaller to medium size silver NPs that can retain FCC structure after 3D printing of the Ag-Ink.

42 ENGINEERING↗
DOE OSTI2023

An investigation on the structural stability of $\mathrm{ZIF}$-8 in water versus water-derived oxidative species in aqueous environment

We report the zeolitic-imidazolate-framework-8 (ZIF-8) is one of the extensively studied metal-organic frameworks (MOF) materials because of its unique structure. For its potential applicability in numerous fields, it becomes crucial to have detailed studies on the structural stability of ZIF-8, especially in aqueous environments. A number of studies have been conducted to investigate the breakdown process of the ZIF-8 structure in water; which is known as the hydrolysis of ZIF-8. However, those studies reported different opposing experimental observations on the role of water on the structural stability of ZIF-8, which created obscurity in understanding this phenomenon. This study explored the effects of different water-derived species on the structural stability of ZIF-8; specifically, examined the effects of only water and water with different oxidative species that may be generated by water molecules' dissociation under external energy or catalyst presence. To this effort, we experimentally probed the physical and chemical structural changes of ZIF-8 in DI water and three different solutions of hydrogen peroxides (H 2 O 2 ); taking H 2 O 2 as the source of oxidative species. To assess the changes in elemental compositions, chemical bonds, functional groups, crystal structure, and morphology, all the samples were analyzed by X-ray photoelectron spectroscopy (XPS), energy-dispersive x-ray (EDX) spectroscopy, Fourier Transform Infrared (FTIR) spectroscope, X-ray diffractometer (XRD), and scanning electron microscope (SEM). Significant structural changes in ZIF-8 occurred mainly in the presence of oxidative species in water. Notably, oxidative species' concentration exceeding 1 M heightened the deformation of the ZIF-8 structure.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Modeling aqueous association constants and mineral solubilities at subcritical and supercritical temperatures

The need for sustainable power generation has increased interest in the use of hydrothermal fluids for industrial applications. New high-enthalpy geothermal systems and biowaste-to-fuel processes are two relevant examples that employ supercritical fluids which require an in-depth understanding of complex chemical reactions occurring near the supercritical temperature of water (374 °C). As these processes operate in thermodynamic regimes that are not currently covered by a standard molar Gibbs energy of formation model, only empirical fits for single reaction systems are available which limit the use of multi-component phase equilibria calculations that are standard practice for less extreme environments. Here, in this paper, we advance a standard molar Gibbs energy of formation model able to operate in these otherwise inaccessible thermodynamic states to include species needed for key mineral solubility systems and ion association reactions. This work extends a model based on molecular statistical thermodynamics (MST) into four new systems (Na 3 PO 4 -H 2 O, LiOH-H 2 O, KOH-H 2 O, and BaSO 4 -H 2 O) by extending the model to cover 10 new species. For each of these systems, model predictions were consistently within the experimental uncertainties for the new systems covered. A breakdown of MST contributions to the model revealed that electrostatic and hard sphere contributions were key to reproducing density dependencies of standard molar Gibbs energy of formation values around the critical point of water.

42 ENGINEERING↗
DOE OSTI2022

Susceptibility weighted MRI pinpoints spontaneous intracerebral hemorrhage in stroke-prone spontaneously hypertensive rats

Purpose: To find magnetic resonance imaging (MRI) precursors of spontaneous intracerebral hemorrhage in stroke-prone spontaneously hypertensive rats (SHRSP). Method: SHRSP rats were used with both a low/high salt (n = 18 or 11) Japanese diet and salty drinking water to generate spontaneous intracerebral hemorrhage (ICH). Various MRI sequences, and in particular, susceptibility weighted imaging (SWI), were used and combined with a gadolinium (Gd) contrast agent or oxygen gas to identify the rupture of the blood brain barrier (BBB) and the temporal ICH. Results: Most rats developed hypertensive ICH stroke in the high salt group during the 10–13 week period compared to only one third of rats in the low salt group during the 14–18 week period. The location of stroke for both the low/high-salt groups was highest in the striatum (58%/43%), followed by the cortex (21%/30%). The edematous enhancement on T2 weighted (T2W) imaging or Gd based T1 weighted (Gd-T1W) imaging due to the ruptured BBB preceded the striatal hemorrhages seen on SWI. The most recent bleeds were observed on temporal SWI or on oxygen-enhanced SWI. The mode of the volume of bleeds was 0.4 mm 3 . A positive correlation between susceptibility x volume and R2* x volume of the bleeds was observed. Conclusions: SHRSP rats with the high salt diet effectively generated a hypertensive hemorrhagic stroke which could be monitored by various MRI sequences. The venous dilation on SWI may precede any abnormality on T2W or Gd-T1W imaging. The edematous enhancement on T2W or Gd-T1W indicated a BBB breakdown that may precede striatal ICH by several days. This suggests the need for immediate treatment to improve outcome if this finding is observed. Here, the use of oxygen with SWI was able to help differentiate old bleeds from very recent bleeds.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Effects of applied stress and grain size on creep-rupture lifetime prediction for Haynes 282 alloy

A multiple-heat set of tensile and creep-rupture data generated from a single laboratory was used to establish and evaluate predictive equations for the average creep-limited lifetime of an aged wrought Haynes 282 alloy using two different time- and temperature-compensated parametric models (those of Larson and Miller and Wilshire et al.). The range of temperatures and stresses used to produce the creep-rupture data used in the analyses revealed that two distinct regimes, above and below the proportional limit, were necessary for more accurate predictions of creep lifetimes over the range of conditions studied. Furthermore, a 2x difference in grain size amongst the three heats revealed a breakdown in the relationship between ultimate tensile strength and creep-rupture time, thus impacting the predictive ability of the Wilshire model. Finally, lifetime predictions based on the formulations from the respective models were compared to other available Haynes 282 datasets and found to reasonably replicate the experimental trends established in other studies.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructural evolution and strengthening mechanisms in a heat-treated additively manufactured Al–Cu–Mn–Zr alloy

In this report the microstructural and strength evolution of an additively manufactured Al-8.6Cu-0.5Mn-0.9Zr alloy upon aging at 300, 350, and 400 °C is investigated. The strengthening phases of the alloy evolve significantly upon aging, with breakdown and spheroidization of the interconnected θ-Al 2 Cu network, dissolution of metastable θ'-Al 2 Cu precipitates, and precipitation of nanometric L1 2 -Al 3 Zr from a matrix supersaturated in Zr. In the peak-aged states, the alloy displays a favorable combination of strength and ductility, with a room-temperature yield strength of 314–341 MPa and ductility of 11–13%. The measured yield strengths for microstructures with different aging treatments are compared to predictions of yield strengths from grain boundary, solid solution, and particle strengthening contributions. The observed strain hardening behavior is related to fundamental precipitate and dislocation interactions. Comparison between predicted and measured strength values indicates a continued need for strengthening models specifically developed for the heterogeneous microstructures of additively manufactured alloys.

36 MATERIALS SCIENCE↗