SEARCH · Engineering Papers

Results for “blade”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Minimum weight design of rectangular and tapered helicopter rotor blades with frequency constraints

The minimum weight design of a helicopter rotor blade subject to constraints on coupled flap-lag natural frequencies has been studied. A constraint has also been imposed on the minimum value of the autorotational inertia of the blade in order to ensure that it has sufficient inertia to autorotate in the case of engine failure. The program CAMRAD is used for the blade modal analysis and CONMIN is used for the optimization. In addition, a linear approximation analysis involving Taylor series expansion has been used to reduce the analysis effort. The procedure contains a sensitivity analysis which consists of analytical derivatives of the objective function and the autorotational inertia constraint and central finite difference derivatives of the frequency constraints. Optimum designs have been obtained for both rectangular and tapered blades. Design variables include taper ratio, segment weights, and box beam dimensions. It is shown that even when starting with an acceptable baseline design, a significant amount of weight reduction is possible while satisfying all the constraints for both rectangular and tapered blades.

Chattopadhyay, Aditi↗

NASA NTRS1988

Advancing-side directivity and retreating-side interactions of model rotor blade-vortex interaction noise

Acoustic data are presented from a 40 percent scale model of the four-bladed BO-105 helicopter main rotor, tested in a large aerodynamic wind tunnel. Rotor blade-vortex interaction (BVI) noise data in the low-speed flight range were acquired using a traversing in-flow microphone array. Acoustic results presented are used to assess the acoustic far field of BVI noise, to map the directivity and temporal characteristics of BVI impulsive noise, and to show the existence of retreating-side BVI signals. The characterics of the acoustic radiation patterns, which can often be strongly focused, are found to be very dependent on rotor operating condition. The acoustic signals exhibit multiple blade-vortex interactions per blade with broad impulsive content at lower speeds, while at higher speeds, they exhibit fewer interactions per blade, with much sharper, higher amplitude acoustic signals. Moderate-amplitude BVI acoustic signals measured under the aft retreating quadrant of the rotor are shown to originate from the retreating side of the rotor.

Martin, R. M.↗

NASA NTRS1988

SSME single-crystal turbine blade dynamics

A study was performrd to determine the dynamic characteristics of the Space Shuttle Main Engine high pressure fuel turbopump (HPFTP) blades made of single crystal (SC) material. The first and second stage drive turbine blades of HPFTP were examined. The nonrotating natural frequencies were determined experimentally and analytically. The experimental results of the SC second stage blade were used to verify the analytical procedures. The study examined the SC first stage blade natural frequencies with respect to crystal orientation at typical operating conditions. The SC blade dynamic response was predicted to be less than the directionally solidified base. Crystal axis orientation optimization indicated that the third mode interference will exist in any SC orientation.

Moss, Larry A.↗

NASA NTRS1987

Wall shear stress measurement in blade end-wall corner region

The magnitude and the direction of wall shear stress and surface pressure in the blade end-wall corner region were investigated. The measurements were obtained on a specially designed Preston tube, the tip of which could be concentrically rotated about its axis of rotation at the measurement location. The magnitude of wall shear stress in the vicinity of the corner was observed to increase significantly (170 percent) compared to its far-upstream value; the increase was consistently higher on the blade surface compared to the value on the plate surface of the blade end-wall corner. On both surfaces in the blade end-wall corner, the variation of the wall shear stress direction was found to be more predominant in the vicinity of the blade leading-edge location. The trend of the measured wall shear stress direction showed good agreement with the limiting streamline directions obtained from the flow visualization studies.

Bhargava, R.↗

NASA NTRS1987

The measurement of boundary layers on a compressor blade in cascade. I - A unique experimental facility

A unique cascade facility is described which makes it possible to use LDV for measuring blade boundary layer profiles. Because of the need for a laser access window, the facility cannot rely on continuous blade pack suction to achieve stable flow. Instead, a combination of tailboards and strong suction upstream of the blade pack is used to create a two-dimensional periodic flow field at a chord Reynolds number of 500,000. The distribution of the upstream suction is controlled through a complex baffling system. Details of the inlet and outlet flow are documented using five-hole pressure probes, blade static-pressure measurements, and sublimation flow visualization. Experimental data are presented on the flow field on the suction surface of the blade, the pressure surface, and near-wake flow fields.

Deutsch, Steven↗

NASA NTRS1987

Aeroelastic modeling of swept tip rotor blades using finite elements

A special finite element for the modeling of a swept tip rotor blade is derived. The swept tip blade undergoes moderate deflections in flap, lag and torsion. The nonlinear, partial differential equations of motion are discretized using a Galerkin finite element method. Tip sweep introduces flap-torsion and lag-axial couplings, and may lead to aeroelastic instabilities associated with frequency coalescence. When frequency coalescence does not occur, sweep is usually stabilizing. A comparison of the approximate model of a swept tip blade, using a blade with straight elastic axis and offsets of aerodynamic centers of gravity, with the exact swept tip model developed in this paper indicates that the approximate model can produce inaccurate results for the case of hingeless rotor blades.

Celi, R.↗

NASA NTRS1988

Minimum weight design of rectangular and tapered helicopter rotor blades with frequency constraints

The minimum weight design of a helicopter rotor blade subject to constraints on coupled flap-lag natural frequencies has been studied. A constraint has also been imposed on the minimum value of the autorotational inertia of the blade in order to ensure that it has sufficient inertia to aurorotate in the case of engine failure. The program CAMRAD is used for the blade modal analysis and CONMIN is used for the optimization. In addition, a linear approximation analysis involving Taylor series expansion has been used to reduce the analysis effort. The procedure contains a sensitivity analysis which consists of analytical derivatives of the objective function and the autorotational inertia constraint and central finite difference derivatives of the frequency constraints. Optimum designs have been obtained for both rectangular and tapered blades. Design variables include taper ratio, segment weights, and box beam dimensions. It is shown that even when starting with an acceptable baseline design, a significant amount of weight reduction is possible while satisfying all the constraints for both rectangular and tapered blades.

Chattopadhyay, Aditi↗

NASA NTRS1987

Oxide-dispersion-strengthened turbine blades. Volume 2

The overall objective of Project 4 was to develop and test a high-temperature, uncooled gas turbine blade using MA6000 alloy. Production scale up of the MA6000 alloy was achieved with a fair degree of tolerance to non-optimum processing. The blade manufacturing process was also optimized. The mechanical, environmental, and physical property evaluations of MA6000 were conducted. The ultimate tensile strength, to about 704 C (1300 F), is higher than DS MAR-M 247 but with a corresponding lower tensile elongation. Also, above 982 C (1800 F) MA6000 tensile strength does not decrease as rapidly as MAR-M 247 because the ODS mechanism still remains active. Based on oxidation resistance and diffusional stability considerations, NiCrAlY coatings are recommended. CoCrAlY coating should be applied on top of a thin NiCrAlY coating if hot corrosion is expected. Vibration, whirlpit, and high-rotor-rig tests were conducted to ensure successful completion of the engine test of the MA6000 TFE731 high pressure turbine blades. Test results were acceptable. In production quantities, the cost of the Project 4 MA6000 blade is estimated to be twice that of a cast DS MAR-M 247 blade.

Millan, P. P., Jr.↗

NASA NTRS1989

Structural optimization of rotor blades with straight and swept tips subject to aeroelastic constraints

The main conclusions obtained in the present study are summarized. Their application to the structural optimization of a helicopter blade should be limited by the assumptions used in obtaining the numerical results presented here. The optimum design procedure described here is very efficient, and can produce improved designs with a very limited number of precise analyses. The method of constructing the approximate problem is such that previously conducted aeroelastic analyses can be reused in a new optimization problem. For example, if an optimization study is preceded by a parametric study in which the effect of various combinations of blade design parameters is examined, all the aeroelastic analyses performed for the parametric study can be reutilized in the optimization study. This is not possible when the approximate problem is built from Taylor series expansions. The results of the optimization are quite sensitive to the aeroelastic stability margins required of the blade. In the optimization of case 2, changing the aeroelastic stability constraints from simply requiring that the blade be stable in hover, to requiring that the stability margins be maintained during the course of the optimization, reduced the gains in n/rev vibration levels by more than 50 percent. The introduction of tip sweep can reduce the n/rev vertical hub shears beyond the level that can be obtained by just modifying the mass and stiffness distributions of the blade.

Friedmann, Peretz P.↗

NASA NTRS1988

Unsteady heat transfer in turbine blade ducts - Focus on combustor sources

Thermal waves generated by either turbine rotor blades cutting through nonuniform combustor temperature fields or unsteady burning could lead to thermal fatigue cracking in the blades. To determine the magnitude of the thermal oscillation in blades with complex shapes and material compositions, a finite element Galerkin formulation has been developed to study combustor generated thermal wave propagation in a model two-dimensional duct with a uniform plug flow profile. The reflection and transmission of the thermal waves at the entrance and exit boundaries are determined by coupling the finite element solutions at the entrance and exit to the eigenfunctions of an infinitely long adiabatic duct. Example solutions are presented. In general, thermal wave propagation from an air passage into a metallic blade wall is small and not a problem. However, if a thermal barrier coating is applied to a metallic surface under conditions of a high heat transfer, a good impedance match is obtained and a significant portion of the thermal wave can pass into the blade material.

Baumeister, K. J.↗

NASA NTRS1989

Composite Blade Structural Analyzer (COBSTRAN) theoretical/programmer's manual

This manual describes the organization and flow of data and analysis in the computer code, COBSTRAN (COmposite Blade STRuctural ANalyzer). This code combines composite mechanics and laminate theory with an internal data base of fiber and matrix properties and was developed for the design and analysis of composite turbofan and turboprop blades and composite wind turbine blades. Inputs to the code are constituent fiber and matrix material properties, factors reflecting the fabrication process, composite geometry and blade geometry. COBSTRAN performs the micromechanics and laminate analyses of these fiber composites and generates a NASTRAN finite element model of the blade. This manual describes the equations formulated and solved in the code and the function of each of the seventy-two subroutines. COBSTRAN is written in FORTRAN 77.

Aiello, Robert A.↗

NASA NTRS1989

Effect of reduced aft diameter and increased blade number on high-speed counterrotation propeller performance

Performance data of 0.17-scale model counterrotation pusher propeller configurations were taken in the NASA Lewis 8- by 6-Foot Supersonic Wind Tunnel at Mach numbers of 0.66, 0.71, 0.75, and 0.79. These tests investigated the aerodynamic performance of the unducted fan (UDF) demonstrator propeller engine developed in a joint program by General Electric and NASA. Data were recorded to show the effect on counterrotation propeller cruise efficiency of two takeoff noise-reduction concepts. These two concepts are reduced aft blade diameter and increased forward blade number. The four configurations tested were a baseline (F1/A1 8/8) configuration, a reduced aft diameter (F1/A3 8/8) configuration, an increase forward blade number (F1/A1 9/8) configuration, and a combination of the latter two (F1/A3 9/8) configurations. Data were collected with a complex counterrotation propeller test rig via rotating thrust and torque balances and pressure instrumentation. Data comparisons documented the power differences between the baseline and the reduced aft diameter concepts. Performance comparisons to the baseline configuration showed that reducing the aft blade diameter reduced the net efficiency, and adding a blade to the front rotor increased the net efficiency. The combination of the two concepts showed only slightly lower net efficiency than the baseline configuration. It was also found that the counterrotation demonstrator propeller model (F7/A7 8/8) configuration outperformed the baseline (F1/A1 8/8) configuration.

Rose, Gayle E.↗

NASA NTRS1990

Performance Data from a Wind-Tunnel Test of Two Main-rotor Blade Designs for a Utility-Class Helicopter

An investigation was conducted in the NASA Langley Transonic Dynamics Tunnel to evaluate an advanced main rotor designed for use on a utility class helicopter, specifically the U.S. Army UH-60A Blackhawk. This rotor design incorporated advanced twist, airfoil cross sections, and geometric planform. For evaluation purposes, the current UH-60A main rotor was also tested and is referred to as the baseline blade set. A total of four blade sets were tested. One set of both the baseline and the advanced rotors were dynamically scaled to represent a full scale helicopter rotor blade design. The remaining advanced and baseline blade sets were not dynamically scaled so as to isolate the effects of structural elasticity. The investigation was conducted in hover and at rotor advance ratios ranging from 0.15 to 0.4 at a range of nominal test medium densities from 0.00238 to 0.009 slugs/cu ft. This range of densities, coupled with varying rotor lift and propulsive force, allowed for the simulation of several vehicle gross weight and density altitude combinations. Performance data are presented for all blade sets without analysis; however, cross referencing of data with flight condition may be useful to the analyst for validating aeroelastic theories and design methodologies as well as for evaluating advanced design parameters.

Singleton, Jeffrey D.↗

NASA NTRS1988

Measurement of the steady surface pressure distribution on a single rotation large scale advanced prop-fan blade at Mach numbers from 0.03 to 0.78

The aerodynamic pressure distribution was determined on a rotating Prop-Fan blade at the S1-MA wind tunnel facility operated by the Office National D'Etudes et de Recherches Aerospatiale (ONERA) in Modane, France. The pressure distributions were measured at thirteen radial stations on a single rotation Large Scale Advanced Prop-Fan (LAP/SR7) blade, for a sequence of operating conditions including inflow Mach numbers ranging from 0.03 to 0.78. Pressure distributions for more than one power coefficient and/or advanced ratio setting were measured for most of the inflow Mach numbers investigated. Due to facility power limitations the Prop-Fan test installation was a two bladed version of the eight design configuration. The power coefficient range investigated was therefore selected to cover typical power loading per blade conditions which occur within the Prop-Fan operating envelope. The experimental results provide an extensive source of information on the aerodynamic behavior of the swept Prop-Fan blade, including details which were elusive to current computational models and do not appear in the two-dimensional airfoil data.

Bushnell, Peter↗

NASA NTRS1990

An enhanced integrated aerodynamic load/dynamic optimization procedure for helicopter rotor blades

An enhanced integrated aerodynamic load/dynamic optimization procedure is developed to minimize vibratory root shears and moments. The optimization is formulated with 4/rev vertical and 3/rev inplane shears at the blade root as objective functions and constraints, and 4/rev lagging moment. Constraints are also imposed on blade natural frequencies, weight, autorotational inertia, centrifugal stress, and rotor thrust. The 'Global Criteria Approach' is used for formulating the multi-objective optimization. Design variables include spanwise distributions of bending stiffnesses, torsional stiffness, nonstructural mass, chord, radius of gyration, and blade taper ratio. The program CAMRAD is coupled with an optimizer, which consists of the program CONMIN and an approximate analysis, to obtain optimum designs. The optimization procedure is applied to an advanced rotor as a reference design. Optimum blade designs, obtained with and without a constraint on the rotor thrust, are presented and are compared to the reference blade. Substantial reductions are obtained in the vibratory root forces and moments. As a byproduct, improvements are also found in some performance parameters, such as total power required, which were not considered during optimization.

Chattopadhyay, Aditi↗

NASA NTRS1988

Analysis of nonuniform subsonic flows about a row of moving blades

The motion of a nonuniform flow about a row of moving blades is modeled as that of a three-dimensional rotational disturbance convected by the mean flow. The aerodynamic theories for such flows are reviewed for both linearly propagating disturbances and disturbances distorted by the mean flow. Linear theories results are examined to assess the effects of the gust variables, the Mach number, and the blade spacing, on the unsteady blade response. For loaded blades, the upstream disturbances are distorted by the blade mean flow. For a potential mean flow, the governing equations can be reduced to a single inhomogeneous nonconstant coefficient convective wave equation. A numerical procedure is developed using an elliptic grid system. The accuracy of the solutions strongly depends on the far-field radiation condition and the optimum determination of the grid system. Solutions are presently obtained for thick symmetric airfoils in three-dimensional gusts.

Atassi, H. M.↗

NASA NTRS1989

Effect of reduced aft diameter and increased blade number of high-speed counterrotation propeller performance

Gayle, E. Rose↗

NASA NTRS1990

Aeroelastic stability analysis of a high-energy turbine blade

The dynamic analysis for the SSME HPOTP first stage turbine blade is presented wherein the rotor aeroelastic stability is assessed. The method employs normal modes analysis to simulate the coupled blade/fluid system. A three-dimensional finite element model of the blade is used in conjunction with a two-dimensional linearized unsteady aerodynamic theory which accounts for steady aerodynamic loading effects. This unsteady aerodynamic model is applied in stacked axisymmetric strips along the airfoil span. The blade dynamic and aerodynamic behaviors are coupled within modal space by expressing the unsteady aerodynamic forces in the frequency domain. A complex eigenvalue problem is solved to determine the stability of the rotor assuming tuned blades. The present analysis indicates that the HPOTP rotor experiences very low aerodynamic damping in the first four vibrational modes. The edgewise mode was found to be dynamically unstable. This mode of the blade became stable when the effect of mechanical damping was considered.

Smith, Todd E.↗