Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “below- threshold ionization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Electron-Impact-Induced Fragmentation of a Glutamine Molecule

The formation of ionized products upon single and dissociative ionization of a glutamine (C{sub 5}H{sub 10}N{sub 2}O{sub 3}) molecule by electron impact at low (70 eV) and high (11.5 MeV) energies has been studied by method of mass spectrometry. The mass spectra of glutamine molecules have been obtained upon electron irradiation to various doses (0, 5, 10, and 20 kGy) and for various threshold functions of ion fragment yield. The absolute values of ion fragment appearance energies are determined. Electron beams were generated by a three-electrode gun and electron accelerator (microtron). Comparative analysis of the measured mass spectra of unirradiated and irradiated glutamine molecules showed that high-energy irradiation produced irreversible changes in the molecular structure.

74 ATOMIC AND MOLECULAR PHYSICS↗

Short Circuit Detection and Voltage Sense for High Voltage Ionization Tube Power Supplies

Fermilab's PIP-II upgrade requires new rack-mounted power supplies for Beam Loss Monitor (BLM) ionization tubes compatible with the microTCA 4.1 standard, supporting high-side current measurement for short circuit detection, voltage sense telemetry, and low-side current measurement for beam loss readout. This work presents the design and preliminary schematic of such a supply. A resistive current sensing approach was chosen over inductive, optical, and Hall-effect alternatives for its independence from cable length and component availability. A 500 mΩ inline shunt steps the 2 kV common mode voltage down to roughly 70 V, producing a ~27 μV pulse during a short, which is amplified 500x, compared against a 14-bit DAC threshold, and latched to drive a fault line. Voltage sense steps the 2 kV output down at a 1V/1000V ratio, buffers it with a low bias current amplifier, and digitizes it via a 24-bit ADC over SPI. Onboard power is regulated from 12 V down to isolated 5 V and 3.3 V rails, with capacitive isolation on FPGA communication lines. Lumped parameter models were developed for the ionization tube (0.327 nF, 20 to 200 GΩ dynamic resistance) and the RG-58 coaxial cable to support the design. Component selection is complete and a preliminary schematic has been drawn in Altium Designer, forming the foundation for future prototyping and validation.

Yu, Kellen [Cornell U.]↗

The Significance of the Bystander Effect: Modeling, Experiments, and More Modeling

Non-targeted (bystander) effects of ionizing radiation are caused by intercellular signaling; they include production of DNA damage and alterations in cell fate (i.e. apoptosis, differentiation, senescence or proliferation). Biophysical models capable of quantifying these effects may improve cancer risk estimation at radiation doses below the epidemiological detection threshold. Understanding the spatial patterns of bystander responses is important, because it provides estimates of how many bystander cells are affected per irradiated cell. In a first approach to modeling of bystander spatial effects in a three-dimensional artificial tissue, we assumed the following: (1) The bystander phenomenon results from signaling molecules (S) that rapidly propagate from irradiated cells and decrease in concentration (exponentially in the case of planar symmetry) as distance increases. (2) These signals can convert cells to a long-lived epigenetically activated state, e.g. a state of oxidative stress; cells in this state are more prone to DNA damage and behavior alterations than normal and therefore exhibit an increased response (R) for many end points (e.g. apoptosis, differentiation, micronucleation). These assumptions were implemented by a mathematical formalism and computational algorithms. The model adequately described data on bystander responses in the 3D system using a small number of adjustable parameters. Mathematical models of radiation carcinogenesis are important for understanding mechanisms and for interpreting or extrapolating risk. There are two classes of such models: (1) long-term formalisms that track pre-malignant cell numbers throughout an entire lifetime but treat initial radiation dose-response simplistically and (2) short-term formalisms that provide a detailed initial dose-response even for complicated radiation protocols, but address its modulation during the subsequent cancer latency period only indirectly. We argue that integrating short- and long-term models is needed. As an example of this novel approach, we integrated a stochastic short-term initiation/inactivation/repopulation model with a deterministic two-stage long-term model. Within this new formalism, the following assumptions are implemented: radiation initiates, promotes, or kills pre-malignant cells; a pre-malignant cell generates a clone, which, if it survives, quickly reaches a size limitation; the clone subsequently grows more slowly and can eventually generate a malignant cell; the carcinogenic potential of pre-malignant cells decreases with age. The effectiveness of high-LET radiation per unit dose increases as dose rate decreases. This “inverse dose rate effect” is seen in radon-induced lung carcinogenesis. We suggest a biologically-motivated mechanism based on radiation-induced direct and bystander-effect-related risks: During radon exposure, only a fraction of cells are traversed by alpha particles. These irradiated cells have an increased probability of being initiated into a pre-malignant state. They release signals, which convert some nearby unirradiated cells to an activated state. When already pre-malignant cells are activated, their proliferation (promotion) rate increases. If a radiation dose is sufficient to activate most susceptible cells, protracting the exposure does not substantially decrease the number of activated cells, but prolongs the activated state during which pre-malignant cell proliferation is accelerated. This mechanism is implemented in a low-dose-rate extension of our carcinogenesis model, which integrates both short- and long-term modeling approaches, and was applied to radiotherapy-induced second cancer risk estimation. Model predictions adequately describe the data on radon-induced lung carcinogenesis in humans and rats, using few adjustable parameters. Conclusions about the relative importance of promotion vs. initiation for radon carcinogenesis are similar to those reported with the two-stage clonal expansion model, but a mechanistic explanation for promotion is provided.

59 BASIC BIOLOGICAL SCIENCES↗

Attosecond time delays at Cooper minima in valence-shell photoionization of alkali-metal and alkaline-earth-metal atoms

Ji et al. [New J. Phys. 26, 093014 (2024)] established a direct link between the photoionization cross section and the attosecond time delay near Cooper minima (CM) in the valence shells of noble-gas atoms. This link is based on the analytic properties of the ionization amplitude in the complex plane of the photoelectron energy, and is particularly sensitive to the winding number of the amplitude around the origin of the complex energy plane. Here, in this study, we demonstrate an analogous relation for photoionization of the valence 𝑛⁢𝑠 shells of alkali-metal atoms (AMA), from Na (𝑛 = 3) to Cs (𝑛 = 6), as well as alkaline-earth-metal atoms (AEMA), from Mg (𝑛 = 3) to Ba (𝑛 = 6). To this end, we employ a fully relativistic formalism that separates the two complementary 𝑛⁢𝑠 1/2 → 𝐸⁢𝑝 1/2 and 𝐸⁢𝑝 3/2 ionization channels. Each of these channels exhibits a phase variation close to 𝜋, but in opposite directions, near their respective Cooper minima. This phase variation vanishes in a nonrelativistic formulation, where the two channels become degenerate. For AMA, due to the threshold proximity of the CM, the universal Coulomb contribution to the time delay must be subtracted. The remaining component of the time delay is target-specific, angular-dependent, and accessible through comparative measurements.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Hyper-Velocity Nanoparticle Plasma Jet as Fast Probe for Runaway Electrons in Tokamak Disruptions

The large energy focalized deposition of the runaway electron (RE) beam on the first wall can potentially yield to destructive effects on the reactor vessel during the explosive instability of a major disruption in a large tokamak (e.g. RE beam estimation is multi-MA of ~10 MeV energy in ITER.) Impurity injection is seen as an effective way to suppress REs after thermal quench (TQ). Injected material in solid state is advantageous, but it must be in small size grain form, with large surface-to-mass ratio to facilitate its rapid ablation within plasma. However, the results using shattered pellet injection (SPI), a technique aiming to satisfy these condition, indicated that the relatively unexplored RE evolution phases and RE beam-plasma interaction are far from being properly diagnosed and fully understood. We proposed the idea to probe REs with a pulsed power hyper-velocity large-mass nanoparticle plasma jet (NPPJ). NPPJ provides a high specific surface area and swift injection to core, hence fast increase of three basic parameters: 1) the electron density ne (bound and free through ionization, if the cold post-TQ plasma has a still high enough T e ), 2) the effective charge (Z eff ) which rises both the dynamical friction force and plasma resistivity, and, finally, 3) the value of the (Dreicer and critical) threshold E-field above which electrons are accelerated and become REs. But the fast transient phenomena of RE ”seed” creation, RE ”avalanche” multiplication, and RE beam formation and interaction with the background plasma all take place dominantly in the core plasma, where the induction E-field has its maximum. Thus, the RE probe success requires a rapid (1 - 2 ms) injection of sufficient mass able to penetrate through the strong toroidal magnetic field (2 - 5 T) over a long distance (~1 - 2 m) with a large assimilation fraction in the core plasma. As a RE probe, NPPJ is a unique combination of fast response with trigger-to-delivery time of few milliseconds, large mass-velocity (>75 mg at several km/s) and deep injection into post-TQ central plasma. The Objectives of this Category #1 project (concept development) were as follows: 1: We investigated the essential basic physics aspects of creating a plasma with ~10 15 to 10 16 cm -3 boron nitride (BN) NP density suited for a pulsed power plasma gun acceleration to several km/s. We concluded that, for RE NPPJ probe, BN (diameter Ø10 to 100 nm NPs) are in all respects usable. 2: We advanced solutions to get BN NPPJ by adapting FAR-TECH’s technology for C 60 NPPJ. 3: We developed self-consistent models for RE current density j RE (R; t) evolution in the TQ aftermath, with fast and simultaneous increase of n e (R; t) and Z eff (R; t) > 1 upon the specific injection of C 60 (i.e. C ions) and BN NP (i.e. B and N ions), respectively. We showed that prompt post-TQ injection and high velocity are of essence in RE probe diagnostics and suppression. 4: We used the in-house HEM-2D code to simulate the C$_{60}^{q+}$ NPPJ transverse penetration through tokamak-level B-field (BT ~2 to 5 T) and distance (~1 to 2m), with fragmentation of C$_{60}^{q+}$ and developed the algorithm for BN Q+ NPPJ ablative sublimation of BN Q+ NP by the collisions with post-TQ plasma electrons. HEM-2D results indicated that fragmenting C$_{60}^{1+}$ NPPJ penetrates up to ~60 cm in 100 us when injecting at 1.6 ms after TQ and gradually released C 2 fragments and C ions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The AGORA High-resolution Galaxy Simulations Comparison Project. VI. Similarities and Differences in the Circumgalactic Medium

Abstract We analyze the circumgalactic medium (CGM) for eight commonly-used cosmological codes in the AGORA collaboration. The codes are calibrated to use identical initial conditions, cosmology, heating and cooling, and star formation thresholds, but each evolves with its own unique code architecture and stellar feedback implementation. Here, we analyze the results of these simulations in terms of the structure, composition, and phase dynamics of the CGM. We show properties such as metal distribution, ionization levels, and kinematics are effective tracers of the effects of the different code feedback and implementation methods, and as such they can be highly divergent between simulations. This is merely a fiducial set of models, against which we will in the future compare multiple feedback recipes for each code. Nevertheless, we find that the large parameter space these simulations establish can help disentangle the different variables that affect observable quantities in the CGM, e.g., showing that abundances for ions with higher ionization energy are more strongly determined by the simulation’s metallicity, while abundances for ions with lower ionization energy are more strongly determined by the gas density and temperature.

79 ASTRONOMY AND ASTROPHYSICS↗

Volume nanograting formation in laser-silica interaction as a result of the 1D plasma-resonance ionization instability

The initial stage of the small-scale ionization-induced instability developing inside the fused silica volume exposed to the femtosecond laser pulse is studied as a possible initial cause of the self-organized nanograting formation. We have calculated the spatial spectra of the instability with the electron-hole diffusion taken into account for the first time and have found that it results in the formation of some hybrid (diffusion-wave) 1D structure with the spatial period determined as the geometrical mean of the laser wavelength and characteristic diffusion length of the process considered. Near the threshold of the instability, this period occurs to be approximately equal to the laser half-wavelength in the silica, close to the one experimentally observed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Radiation leukaemogenesis at low doses

This report provides a complete summary of the work undertaken and results obtained under US Department of Energy grant DF-FG02-05 ER 63947, Radiation leukaemogenesis at low doses. There is ample epidemiological evidence indicating that ionizing radiation is carcinogenic in the higher dose range. This evidence, however, weakens and carries increasing uncertainties at doses below 100-200 mSv. At these low dose levels the form of the dose-response curve for radiation-induced cancer cannot be determined reliably or directly from studies of human populations. Therefore animal, cellular and other experimental systems must be employed to provide supporting evidence on which to base judgements of risk at low doses. Currently in radiological protection a linear non-threshold (LNT) extrapolation of risk estimates derived from human epidemiological studies is used to estimate risks in the dose range of interest for protection purposes.

59 BASIC BIOLOGICAL SCIENCES↗

Two-electron photoionization of ground-state lithium

We apply the convergent close-coupling (CCC) formalism to single-photon two-electron ionization of the lithium atom in its ground state. We treat this reaction as single-electron photon absorption followed by inelastic scattering of the photoelectron on a heliumlike Li{sup +} ion. The latter scattering process can be described accurately within the CCC formalism. We obtain integrated cross sections of single photoionization leading to the ground and various excited states of the Li{sup +} ion as well as double photoionization extending continuously from the threshold to the asymptotic limit of infinite photon energy. Comparison with available experimental and theoretical data validates the CCC model.

74 ATOMIC AND MOLECULAR PHYSICS↗

HIGH-TEMPERATURE IONIZATION IN PROTOPLANETARY DISKS

We calculate the abundances of electrons and ions in the hot (≳500 K), dusty parts of protoplanetary disks, treating for the first time the effects of thermionic and ion emission from the dust grains. High-temperature ionization modeling has involved simply assuming that alkali elements such as potassium occur as gas-phase atoms and are collisionally ionized following the Saha equation. We show that the Saha equation often does not hold, because free charges are produced by thermionic and ion emission and destroyed when they stick to grain surfaces. This means the ionization state depends not on the first ionization potential of the alkali atoms, but rather on the grains’ work functions. The charged species’ abundances typically rise abruptly above about 800 K, with little qualitative dependence on the work function, gas density, or dust-to-gas mass ratio. Applying our results, we find that protoplanetary disks’ dead zone, where high diffusivities stifle magnetorotational turbulence, has its inner edge located where the temperature exceeds a threshold value ≈1000 K. The threshold is set by ambipolar diffusion except at the highest densities, where it is set by Ohmic resistivity. We find that the disk gas can be diffusively loaded onto the stellar magnetosphere at temperatures below a similar threshold. We investigate whether the “short-circuit” instability of current sheets can operate in disks and find that it cannot, or works only in a narrow range of conditions; it appears not to be the chondrule formation mechanism. We also suggest that thermionic emission is important for determining the rate of Ohmic heating in hot Jupiters.

79 ASTRONOMY AND ASTROPHYSICS↗

Total and partial electron impact ionization cross sections of fusion-relevant diatomic molecules

We discuss calculations of total (and absolute) electron-impact ionization cross sections (EICSs) for the fusion-relevant diatomic molecular species BeH, BeN, BeO, WH, WBe, WN, WO, O 2 , and N 2 by means of the Deutsch-Märk and the binary-encounter-Bethe approaches in the energy range from threshold to 10 keV. In addition, we discuss an empirical scheme to estimate partial cross sections from the total ones based on reaction energetics and empirical threshold laws and explore its accuracy by assessing available experimental data on total and partial EICSs. Lastly, we also observe parameters obtained by fitting the calculated cross sections to an expression commonly used in fusion edge plasma modeling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Color-Center Production and Formation in Electron-Irradiated Magnesium Aluminate Spinel and Ceria

Single crystals of magnesium aluminate spinel (MgAl2O4) with (100) or (110) orientations and cerium dioxide or ceria (CeO2) were irradiated by 1.0-MeV and 2.5-MeV electrons in a high fluence range. Point-defect production was studied by off-line UV-visible optical spectroscopy after irradiation. For spinel, regardless of both crystal orientation and electron energy, two characteristic broad bands centered at photon energies of 5.4 eV and 4.9 eV were assigned to F and F+ centers (neutral and singly-ionized oxygen vacancies), respectively, on the basis of available literature data. No clear differences in colour-centre formation were observed for the two crystal orientations. Using calculations of displacement cross sections by elastic collisions, these results are consistent with a very large threshold displacement energy (200 eV) for oxygen atoms at RT. A third very broad band centered at 3.7 eV might be attributed either to an oxygen hole center (V-type center) or an F2 dimer center (oxygen di-vacancy). The onset of recovery of these color centers took place at 200°C with almost full bleaching at 600°C. Activation energies (~0.3-0.4 eV) for defect recovery were deduced from the isochronal annealing data by using a first-order kinetics analysis. For ceria, a sub band-gap absorption feature peaked at ~3.1 eV was recorded for 2.5-MeV electron irradiation only. Assuming a ballistic process, we suggest that the latter defect might result from cerium atom displacement on the basis of computed cross sections.

36 MATERIALS SCIENCE↗

Atmospheric-pressure Molecular Imaging of Biological Tissues and Biofilms by LAESI Mass Spectrometry

Ambient ionization methods in mass spectrometry allow analytical investigations to be performed directly on a tissue or biofilm under nativelike experimental conditions. Laser ablation electrospray ionization (LAESI) is one such development and is particularly well-suited for the investigation of water-containing specimens. LAESI utilizes a mid-infrared laser beam (2.94 μm wavelength) to excite the water molecules of the sample. When the ablation fluence threshold is exceeded, the sample material is expelled in the form of particulate matter and these projectiles travel to tens of millimeters above the sample surface. In LAESI, this ablation plume is intercepted by highly charged droplets to capture a fraction of the ejected sample material and convert its chemical constituents into gas-phase ions. A mass spectrometer equipped with an atmospheric-pressure ion source interface is employed to analyze and record the composition of the released ions originating from the probed area (pixel) of the sample. A systematic interrogation over an array of pixels opens a way for molecular imaging in the microprobe analysis mode. A unique aspect of LAESI mass spectrometric imaging is depth profiling that, in combination with lateral imaging, enables threedimensional (3D) molecular imaging. With current lateral and depth resolutions of ~100 μm and ~40 μm, respectively, LAESI mass spectrometric imaging helps to explore the molecular structure of biological tissues. Herein, we review the major elements of a LAESI system and provide guidelines for a successful imaging experiment.

59 BASIC BIOLOGICAL SCIENCES↗

Radiation Response of Ga 2 O 3 MOSFETs Probed via Focused Particle Beams

Gallium Oxide (Ga 2 O 3 ), particularly in its β-phase, is attracting lots of interest for high-power and high-voltage electronics due to its wide bandgap, high breakdown field, and thermal stability. This study investigates the radiation response of Ga 2 O 3 Metal-Oxide-Semiconductor Field-Effect Transistors (MOSFETs) under Total Ionizing Dose (TID) and Displacement Damage (DD) conditions, which are critical for applications in radiation environments. Utilizing a dual-beam Focused Ion Beam and Scanning Electron Microscope setup, microscale analysis of radiation effects on individual devices is performed. The findings reveal distinct behaviors under TID and DD + TID conditions, with TID leading to threshold voltage shifts due to trapped charges, while DD results in decreased drive current attributed to increased carrier scattering from lattice defects. Notably, it is demonstrated that the TID effect can be mitigated through dynamic threshold voltage adjustments and that the predicted TID from ions calculated by Monte Carlo simulations overestimates actual TID due to unaccounted charge yield effects. In conclusion, this research enhances the understanding of Ga2O3 MOSFETs' performance in harsh radiation environments, providing insights for the design of robust electronic devices for space and nuclear applications.

MOSFET↗

Design and implementation of a data analysis pipeline for paper spray ionization mass spectrometry of UO 2 Cl 2

Ambient mass spectrometry is an emerging characterization method for nuclear materials analysis. SRNL has recently acquired a new JEOL AccuTOF™-DART® LP 4G with a Filter Spray™ front end sample injection system, to develop new methods for ambient mass spectrometry of uranium analytes. Preliminary measurements of uranium-containing samples have demonstrated a need to rapidly evaluate large datasets generated with tailored data analysis scripts. To address this gap a data analysis pipeline written in R within the R Studio environment has been developed. The pipeline comprises a series of processing steps where the data are ingested, analyte peaks of interest are extracted, subsequent ratio and normalization calculations are performed, and results are presented in a series of graphical plots. In detail, the data files containing up to several hundred chronological spectra of a single sample in netCDF format were first extracted into RStudio. Then, initial 3D plots of the data were created in respect to the time, intensity, and mass to charge domains. These graphics serve as an initial easily visualized survey of instrument data. Next, a .csv format file containing the names, masses, and abundances of isotopes of interest were ingested into RStudio and were used to automatically collect intensity values at the mass value. Uranium isotope ratios were plotted against gadolinium isotope ratios (gadolinium was used as an internal standard) and assessed for ion beam stability and intensity. The spectra were filtered by applying a threshold intensity for the 158GdO+ mass channel. A Monte Carlo experiment was performed by creating a theoretical distribution of the data in order to determine the ratio of the uranium isotopes. The results show that the developed data analysis pipeline successfully filters high quality data from overall poor quality runs. Our results also support the idea that paper spray ionization mass spectrometry can be used for both detection and quantification of trace amounts of uranium compounds.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Enhanced Ionization Charge Identification in the Short-Baseline Neutrino Program Neutrino Detectors with Deep Neural Networks

We present a deep neural net-based region of interest detection method (DNN ROI) for signal processing in the liquid argon time projection chambers of the Short-Baseline Neutrino (SBN) Program, SBND and ICARUS. DNN ROI addresses limitations of the traditional wire-by-wire thresholding algorithm by leveraging the full two-dimensional detector readout and cross-plane matching information. To account for detector performance variations, we explore training with augmented samples. We find that DNN ROI outperforms the traditional method in both low-level ROI identification performance and high-level reconstruction metrics for high-energy cosmic and accelerator neutrino interaction products, while also being more robust against detector variations, with or without sample augmentation.

Abratenko, P. [Tufts U.]↗

A new version of the LUPIN detector: Improvements and latest experimental verification

LUPIN-II is an upgraded version of LUPIN, a novel rem counter first developed in 2010 specifically conceived to work in pulsed neutron fields (PNFs). The new version introduces some modifications that improve the performance of the detector, in particular extending its upper detection limit in PNFs. This paper discusses the characteristics and the performance of the instrument. Measurements have been carried out in radiation fields characterized by very different conditions: the detector has first been exposed in PNFs with intensity up to 5 μSv per burst, where it could keep the H*(10) underestimation below 20% up to 500 nSv per burst. It has then been tested in operational conditions around particle accelerators, where it has shown performances similar to that of ionization chambers. Its proper functioning has also been verified in high energy mixed fields, where the experimental results matched the Monte Carlo predictions. Its neutron/photon discrimination capability has been tested in a steady-state photon field where, via an innovative technique based on a threshold set on the derivative of the current signal, it was capable of rejecting a photon H*(10) rate of about 25 mSv/h, and in a mixed neutron/photon field, where a time-based discrimination method was employed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Non-thermal fluence threshold for femtosecond pulsed x-ray radiation damage in perovskite complex oxide epitaxial heterostructures

Intense hard x-ray pulses from a free-electron laser induce irreversible structural damage in a perovskite oxide epitaxial heterostructure when pulse fluences exceed a threshold value. The intensity of x-ray diffraction from a 25-nm thick epitaxial BiFeO 3 layer on a SrTiO 3 (STO) substrate measured using a series of pulses decreases abruptly with a per-pulse fluence of 2.7 x 10(6) photons mu m -2 at a photon energy of 9.7 keV but remains constant for 1.3 x 10 6 photons mu m -2 or less. The damage resulted in the destruction of the BiFeO 3 thin film within the focal spot area and the formation of a deep cavity penetrating into the STO substrate via the removal of tens of nanometers of material per pulse. The damage threshold occurs at a fluence that is insufficient to heat the absorption volume to the melting point. The morphology of the ablated sample is consistent with fracture rather than melting. Together, these results indicate that the damage occurs via a nonthermal process consistent with ultrafast ionization of the absorption volume.

36 MATERIALS SCIENCE↗