Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “beam control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Performance analysis and simulation of the SPS reference phase control system

The solar power satellite (SPS) concept envisions several hundred thousand synchronized microwave power amplifiers operating in parallel to produce an aggregate power output of 5-10 GW. This power is to be transferred to earth with the aid of a microwave/millimeter-wave beaming system operating in a synchronous orbit. The reference phase control system is considered along with aspects of pilot signal parameter selection. A power transponder analysis is conducted and an SPS performance evaluation is performed. Attention is given to system jitters and imperfections, the definition of power transfer efficiency, and the effects of system imperfections on SPS efficiency. It is found that the power transfer efficiency is relatively insensitive to the amplitude jitters. However, the effects of location jitters can produce a severe degradation of efficiency.

Chie, C. M.↗
NASA NTRS1991

Application of a robust linear control design to a truss structure with nonlinear joints

An efficient nonlinear equivalent beam finite-element method for the application of a full state feedback design is described, which is robust to plant uncertainties to a beamlike truss structure with nonlinear elements. The method may be extended to model nonlinear structures with other types of control systems, such as model-based compensators.

Webster, Mark↗
NASA NTRS1982

Early experiments in charged particle beams from the Space Shuttle

Characteristics of studies on board the Shuttle involving the interaction of particle beams with the atmosphere and the ionosphere, and the effects of the beams on the electrical potential of the platform, are discussed. Noting that the Shuttle allows greater weight and power demands by scientific payloads than previous satellite launches, the OSS-1 Vehicle Charging and Potential experiment and the Spacelab 1 Particle Accelerator and Phenomena Induced by Charged Particle Beams are described. Instrumentation details are provided, including charge and current probes, the Spherical Retarding Potential Analyzer, the Fast Pulse Electron Generator, and digital control and interface units. The SEPAC equipment, which comprises an electron beam accelerator, and MPD plasma jet, and diagnostic units are detailed, and operating procedures and experiment objectives are outlined.

Raitt, W. J.↗
NASA NTRS2007

'NASA Invention of the Year' Controls Noise and Vibration

Developed at NASA's Langley Research Center, the Macro-Fiber Composite (MFC) is designed to control vibration, noise, and deflections in composite structural beams and panels. Smart Material Corporation specializes in the development of piezocomposite components, and licensed the MFC technology from Langley in 2002. To date, Smart Material Corporation has sold MFCs to over 120 customers, including such industry giants as Volkswagen, Toyota, Honda, BMW, General Electric, and the tennis company, HEAD. The company estimates that its customers have filed at least 100 patents for their various unique uses of the technology. In addition, the company's product portfolio has grown to include piezoceramic fibers and fiber composites, piezoceramic actuators and sensors, and test equipment for these products. It also offers a compact, lightweight power system for MFC testing and validation. Consumer applications already on the market include piezoelectric systems as part of audio speakers, phonograph cartridges and microphones, and recreational products requiring vibration control, such as skis, snowboards, baseball bats, hockey sticks, and tennis racquets.

Source record↗
NASA NTRS2003

Effects of a Scanning Reflectarray Antenna on Modulated Data Modeled

The ferroelectric reflectarray is a new type of scanning antenna under development for space and ground communications and radar applications at the NASA Glenn Research Center. The reflectarray offers tremendous cost, gain, and efficiency advantages in comparison to the state-of-the-art phased arrays, but there is an inherent intersymbol interference (ISI) problem with digital communication data streams processed through the array because of the way the reflectarray is operated. This interference stems from the fact that the antenna beam is formed by the superposition of reflected waves from the array elements. The delays from the elements to the observation point of each wave differ. Ferroelectric phase shifters are designed to compensate for the modulo-2p phase differences so that the waves will constructively interfere at the sinusoidal carrier level; however, the delays of the integer-number multiple of the carrier period are not compensated for. This lack of compensation causes ISI in digital modulated signals. ISI has not been a problem with analog modulations and low-rate digital modulations since the distortion (or ISI) introduced is negligible. The problem becomes acute when the data rate gets higher, and the electrical size of the array gets bigger. Moreover, there are intrinsic transient effects associated with the phase shifters and the controller that executes the algorithm to direct the beam. That is, phase shifter updates to redirect the beam may be initiated simultaneously, but nonlinearity will cause different settling times. The ISI problem and other effects ultimately limit the size (gain) and data rate of the reflectarray. An ISI analysis was required to prove or disprove the suitability of the reflectarray antenna for high-rate digitally modulated signals and to give guidance for determining antenna parameters. In this research, the nature of the ISI of the reflectarray has been mathematically modeled.

Romanofsky, Robert R.↗
NASA NTRS2008

Deflection-Compensating Beam for use inside a Cylinder

A design concept for a beam for a specific application permits variations and options for satisfying competing requirements to minimize certain deflections under load and to minimize the weight of the beam. In the specific application, the beam is required to serve as a motion-controlled structure for supporting a mirror for optical testing in the lower third portion of a horizontal, cylindrical vacuum chamber. The cylindrical shape of the chamber is fortuitous in that it can be (and is) utilized as an essential element of the deflection-minimizing design concept. The beam is, more precisely, a table-like structure comprising a nominally flat, horizontal portion with vertical legs at its ends. The weights of the beam and whatever components it supports are reacted by the contact forces between the lower ends of the legs and the inner cylindrical chamber wall. Whereas the bending moments arising from the weights contribute to a beam deflection that is concave with its lowest point at midlength, the bending moments generated by the contact forces acting on the legs contribute to a beam deflection that is convex with its highest point at midlength. In addition, the bending of the legs in response to the weights causes the lower ends of the legs to slide downward on the cylindrical wall. By taking the standard beam-deflection equations, combining them with the geometric relationships among the legs and the horizontal portion of the beam, and treating the sliding as a component of deflection, it is possible to write an equation for the net vertical deflection as a function of the load and of position along the beam. A summary of major conclusions drawn from the equation characterization is included.

Goodman, Dwight↗
NASA NTRS1991

LDEF-space environmental effects on materials: Composites and silicone coatings

The objective of the Lockheed experiment is to evaluate the effects of long term low Earth orbit environments on thermal control coatings and organic matrix/fiber reinforced composites. Two diverse categories are reported: silicone coatings and composites. For composites physical and structural properties were analyzed; results are reported on mass/dimensional loss, microcracking, short beam shear, CTE, and flexural properties. The changes in thermal control properties, mass, and surface chemistry and morphology are reported and analyzed for the silicon coatings.

Petrie, Brian C.↗
NASA NTRS1995

Propagation of beam-driven VLF waves from the ionosphere toward the ground

As part of the Cooperative High Altitude Rocket Gun Experiment (CHARGE-2B) rocket mission, an electron beam was injected into the ionosphere with a modulated beam current in an effort to generate very low frequency (VLF) waves. The propagation of the beam-driven VLF waves through the ionosphere is examined here to determine whether it is possible to detect these wave emissions with ground receivers. The paths of the VLF waves from where they were generated near the rocket were followed to the bottom of the ionosphere and the decrease in wave amplitude due to wave-particle resonance and collisional damping was calculated. It was found that due to collisional damping, which for these VLF waves becomes large at altitudes below about 150 km, wave amplitudes were decreased below the background atmospheric noise level. A number of different beam injection events have been examined and in all of these cases studied the waves were sufficiently damped such that detection on the ground would not be possible. This is in agreement with observations on the ground in which no wave emissions were observed during the CHARGE-2B mission. Control parameters that would be more favorable for beam-generated VLF propagation to the ground are discussed for future experiments of this type.

Schriver, David↗
NASA NTRS1975

A 10.6 micron ladar for space rendezvous and docking

The paper describes a 10.6 micron ladar (a laser detection and ranging device) which is considered as a baseline sensor for space rendezvous and docking applications. The sensor uses a passively Q-switched CO2 laser as the transmitter active element, and a four-quadrant photodiode array, operated as a coherent receiver element in the heterodyne mode. The aperture will be about 3 inches, and the telescope will be able to steer the beam in a 40 by 40 degree window. Various aspects of the ladar system are examined in detail, including the laser control loop, the transmitter, the local oscillator, the telescope, and the output beam scanning.

Lowrey, D. O.↗
NASA NTRS1986

Anisotropic etching of Al by a directed Cl2 flux

A new Al etching technique is described that uses an ion beam from a Kaufman ion source and a directed Cl2 flux. The ion beam is used primarily to remove the native oxide and to allow the Cl2 to spontaneously react with the Al film forming volatile Al2Cl6. By controlling both the flux equivalent pressure of Cl2 and the ion beam current, this etching technique makes possible the anisotropic etching of Al with etch rates from 100 nm/min to nearly 10 microns/min with a high degree of selectivity.

Efremow, N. N.↗
NASA NTRS1981

An interferometer-based phase control system

A system for focusing and pointing the SPS power beam is discussed. The system is ground based and closed loop. One receiving antenna is required on earth. A conventional uplinked data channel transmits an 8-bit phase error correction back to the SPS for sequential calibration of each power module. Beam pointing resolution is better than 140 meters at the rectenna.

Ott, J. H.↗
NASA NTRS1980

An interferometer-based phase control system

A system for focusing and pointing the SPS power beam is discussed. The system is ground based and closed loop. One receiving antenna is required on Earth. A conventional uplink data channel transmits an 8-bit phase error correlation back to the SPS for sequential calibration of each power module. Beam pointing resolution is better than 140 meters at the Rectenna.

Ott, J. H.↗
NASA NTRS1980

Control systems design for large flexible space structures

Several approaches for the design of reduced-order linear-quadratic-Gaussian type controllers for large space structures were proposed and evaluated using a continuous model of a long free-free beam. Sufficient conditions were derived for the asymptotic stability with this type of controller. A finite-element model of a free-free-free-free square plate was obtained for use in control systems studies. A method was developed for optimal damping enhancement in large space structures.

Joshi, S. M.↗
NASA NTRS1980

Electron-beam welder circle generator

Generator rotates electron beam and performs other convenient functions during welding process. Device eliminates time-consuming techniques relying heavily on operator's skill. Welding speed is varied with frequency selector, and amplitudes of x- and y-axes are varied by adjusting phase shift. Both high and low-range adjustments are available, and each axis can be separately controlled. Crosshair is provided for set-up and beam alinements.

Burley, R. K.↗
NASA NTRS1993

Real-time dynamics and control strategies for space operations of flexible structures

This project (NAG9-574) was meant to be a three-year research project. However, due to NASA's reorganizations during 1992, the project was funded only for one year. Accordingly, every effort was made to make the present final report as if the project was meant to be for one-year duration. Originally, during the first year we were planning to accomplish the following: we were to start with a three dimensional flexible manipulator beam with articulated joints and with a linear control-based controller applied at the joints; using this simple example, we were to design the software systems requirements for real-time processing, introduce the streamlining of various computational algorithms, perform the necessary reorganization of the partitioned simulation procedures, and assess the potential speed-up realization of the solution process by parallel computations. The three reports included as part of the final report address: the streamlining of various computational algorithms; the necessary reorganization of the partitioned simulation procedures, in particular the observer models; and an initial attempt of reconfiguring the flexible space structures.

Park, K. C.↗
NASA NTRS1980

Line spread instrumentation for propagation measurements

A line spread device capable of yielding direct measure of a laser beam's line spread function (LSF) was developed and employed in propagation tests conducted in a wind tunnel to examine optimal acoustical suppression techniques for laser cavities exposed to simulated aircraft aerodynamic environments. Measurements were made on various aerodynamic fences and cavity air injection techniques that effect the LSF of a propagating laser. Using the quiescent tunnel as a control, the relative effect of each technique on laser beam quality was determined. The optical instrument employed enabled the comparison of relative beam intensity for each fence or mass injection. It was found that fence height had little effect on beam quality but fence porosity had a marked effect, i.e., 58% porosity alleviated cavity resonance and degraded the beam the least. Mass injection had little effect on the beam LSF. The use of a direct LSF measuring device proved to be a viable means of determining aerodynamic seeing qualities of flow fields.

Bailey, W. H., Jr.↗
NASA NTRS1980

Microwave system performance summary

The design of the microwave system for the solar power satellite is described. Design modifications recommended include changes in phase control to the power module level, a reduction in allowable amplitude jitter, the use of metal matrix waveguides, and sequences for startup/shutdown procedures. Investigations into reshaping the beam pattern to improve overall rectenna collection efficiency and improve sidelobe control are surveyed.

Arndt, G. D.↗