Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “backing layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Optimizing CdTe Solar Cell Performance: Impact of Variations in Minority-Carrier Lifetime and Carrier Density Profile

Using numerical simulations, we study the combined effects of nonuniform minority-carrier lifetime t and carrier density NA on device performance. In a uniformly doped device, maximum open-circuit voltage V oc is obtained for high t and high NA . The fill-factor (FF) is mainly dependent on the lifetime. When the lifetime is low, and NA is high, the FF suffers losses due to voltage-dependant carrier collection. For a low carrier density and low lifetime, the electric field strength is low, recombination is a competitive process to drift, and the FF is reduced. Simulations predict that it might be possible to increase the device efficiency with lower carrier density, if the back of the absorber is highly doped. This configuration increases the built-in potential and the electric field close to the junction region, while keeping the space-charge region wide. In addition, a device with such a profile is very tolerant toward lifetime variations of the highly doped layer. With our simulation parameters, when the absorber properties are uniform, efficiencies >;18% require experimentally unrealistic doping and lifetime values. If the back of the absorber is doped significantly higher than the rest, such efficiencies can be achieved with realistic values of doping and lifetime.

14 SOLAR ENERGY↗

Carrier gradients and the role of charge selective contacts in lateral heterojunction all back contact perovskite solar cells

Realizing photovoltaic devices that achieve the full potential of the metal halide perovskite material will require improved insight regarding the role of selective contacts and how key interfaces operate when mobile defects are present. However, measuring interface properties in typical device stacks where the perovskite layer is thin and sandwiched between two contacts has been a challenge. Here, we fabricate p-i-n and p-n lateral heterojunctions with nickel oxide/titanium oxide all back contacts, permitting us to employ a comprehensive analysis approach, including ultraviolet and X-ray photoemission spectroscopy (UPS/XPS), angle-resolved X-ray absorption spectroscopy (XAS), Kelvin probe force microscopy (KPFM), surface photovoltage (SPV), hyperspectral imaging (HSI), and time-resolved fluorescence lifetime imaging microscopy (TR-FLIM) to discern the role of selective contacts. Specifically, we tune the selectivity of the contacts, changing the gradient in the carrier concentration across the surface of the active layer, which is connected to carrier extraction at the buried interface, and thus the device functionality.

25 ENERGY STORAGE↗

Method of forming contacts for a back-contact solar cell

Methods of forming contacts for solar cells are described. In one embodiment, a method includes forming a silicon layer above a substrate, forming and patterning a solid-state p-type dopant source on the silicon layer, forming an n-type dopant source layer over exposed regions of the silicon layer and over a plurality of regions of the solid-state p-type dopant source, and heating the substrate to provide a plurality of n-type doped silicon regions among a plurality of p-type doped silicon regions.

Manning, Jane↗

Method of forming contacts for a back-contact solar cell

Methods of forming contacts for solar cells are described. In one embodiment, a method includes forming a silicon layer above a substrate, forming and patterning a solid-state p-type dopant source on the silicon layer, forming an n-type dopant source layer over exposed regions of the silicon layer and over a plurality of regions of the solid-state p-type dopant source, and heating the substrate to provide a plurality of n-type doped silicon regions among a plurality of p-type doped silicon regions.

14 SOLAR ENERGY↗

Numerical case study of the aerosol–cloud interactions in warm boundary layer clouds over the eastern North Atlantic with an interactive chemistry module

The presence of warm boundary layer stratiform clouds over the eastern North Atlantic (ENA) region is commonly influenced by the Azores High, especially during the summer season. To investigate comprehensive aerosol–cloud interactions, this study employs the Weather Research and Forecasting model coupled with a chemistry component (WRF-Chem), incorporating aerosol chemical components that are relevant to the formation of cloud condensation nuclei (CCN) and accounting for aerosol spatiotemporal variation. This study focuses on aerosol indirect effects, particularly the long-range transport of aerosols, in the ENA region under three different weather regimes: a ridge with a surface high-pressure system, a post-trough with a surface high-pressure system, and a weak trough. The WRF-Chem simulations conducted at a near-large-eddy scale offer valuable insights into the model's performance, especially in terms of its ability to use high spatial resolution to capture mesoscale cloud features across various weather regimes. Our result shows that introducing 5 times more aerosols to either non-precipitating or precipitating clouds significantly increases ambient CCN numbers, resulting in, to varying degrees, higher liquid water path (LWP) values. The substantial aerosol–cloud interaction especially occurs in the precipitating clouds and demonstrates the susceptibility of the LWP to changes in CCN under different regimes. Conversely, thin, non-rain clouds at the edges of a cloud system are prone to evaporation, exhibiting an aerosol drying effect. The aerosols released during this process transition back to the accumulation mode, facilitating future activation. This dynamic behavior is not adequately represented in prescribed-aerosol simulations.

54 ENVIRONMENTAL SCIENCES↗

Comparison of Methods to Determine Tropical Tropopause Layer Cirrus Formation Mechanisms

A new method of estimating Tropical Tropopause Layer Cirrus (TTLC) formation mechanism (object method) is compared to interpretations of formation from previous studies using back trajectory calculations matched to convection identified from satellites and statistical relationships of TTLC with temperature and water vapor. The object method groups neighboring Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) TTLC cloud profiles into cloud objects and classifies them as convective (35% of TTLC) if they are directly attached to a convective cloud along the CALIPSO track. The percentage of back trajectory calculations that intersect convection (39-95% of TTLC within 5 days) depends strongly on the spatial and temporal resolution of the convection data set, and the manner in which deep convection is identified. Using minimum brightness temperature in 3 hourly, 1{sup o} resolution grid boxes to define convection, 46% of non-convective TTLC (37% of all TTLC) did not trace back to convection within 24 h. Back trajectory calculations of thin cirrus identified by the High Resolution Dynamics Limb Sounder (HIRDLS) gave similar results. Temperature is not a good proxy for formation mechanism as convective and non-convective TTLC frequencies both increase monotonically with decreasing temperature at approximately the same rate. Non-convective TTLC frequencies have a stronger relationship with relative humidity than convective TTLC frequencies, though are not sufficiently different to distinguish object method categories. A decrease in TTL cirrus frequency found at low temperatures in previous studies is caused by insufficient variability in reanalysis temperature data and is not indicative of TTLC formation mechanism.

58 GEOSCIENCES↗

Turbulent boundary-layer flow and structure on a convex wall and its redeveloment on a flat wall

Although the number of data sets which show the effects of convex curvature on turbulence has increased in the last 10 years, the development of really good calculational models is being held back by a lack of reliable data. The pesent investigation is concerned with a set of experiments which provide a litle more information regarding the response of a boundary-layer flow to convex curvature. Careful measurements were conducted to show the response of the boudnary layer to a sudden change from flat wall to curvature, and from curvature to flat wall. It was found that curvature effects were clearly apparent one or two boundary-layer thicknesses downstream of the start of curvature, while the disappearance of the curvature effects on a flat wall was an extremely slow process.

Gillis, J. C.↗

Epitaxial growth of high purity cubic InN films on MgO substrates using HfN buffer layers by pulsed laser deposition

Cubic InN films have been grown on MgO substrates with HfN buffer layers by pulsed laser deposition (PLD). It has been found that the use of HfN (100) buffer layers allows us to grow cubic InN (100) films with an in-plane epitaxial relationship of [001]{sub InN}//[001]{sub HfN}//[001]{sub MgO}. X-ray diffraction and electron back-scattered diffraction measurements have revealed that the phase purity of the cubic InN films was as high as 99%, which can be attributed to the use of HfN buffer layers and the enhanced surface migration of the film precursors by the use of PLD. - Graphical abstract: Cubic InN films have been grown on MgO substrates with HfN buffer layers by pulsed laser deposition (PLD). It has been revealed that the phase purity of the cubic InN films was as high as 99 %, which can be attributed to the use of HfN buffer layers and the enhanced surface migration of the film precursors by the use of PLD.

36 MATERIALS SCIENCE↗

SU-E-I-11: Cascaded Linear System Model for Columnar CsI Flat Panel Imagers with Depth Dependent Gain and Blur

Purpose: To implement a depth dependent gain and blur cascaded linear system model (CLSM) for optimizing columnar structured CsI indirect conversion flat panel imager (FPI) for advanced imaging applications. Methods: For experimental validation, depth dependent escape efficiency, e(z), was extracted from PHS measurement of different CsI scintillators (thickness, substrate and light output). The inherent MTF and DQE of CsI was measured using high resolution CMOS sensor. For CLSM, e(z) and the depth dependent MTF(f,z), were estimated using Monte Carlo simulation (Geant4) of optical photon transport through columnar CsI. Previous work showed that Monte Carlo simulation for CsI was hindered by the non-ideality of its columnar structure. In the present work we allowed variation in columnar width with depth, and assumed diffusive reflective backing and columns. Monte Carlo simulation was performed using an optical point source placed at different depth of the CsI layer, from which MTF(z,f) and e(z) were computed. The resulting e(z) with excellent matching with experimental measurements were then applied to the CLSM, Monte Carlo simulation was repeated until the modeled MTF, DQE(f) also match experimental measurement. Results: For a 150 micron FOS HL type CsI, e(z) varies between 0.56 to 0.45, and the MTF at 14 cycles/mm varies between 62.1% to 3.9%, from the front to the back of the scintillator. The overall MTF and DQE(f) at all frequencies are in excellent agreement with experimental measurements at all frequencies. Conclusion: We have developed a CLSM for columnar CsI scintillators with depth dependent gain and MTF, which were estimated from Monte Carlo simulation with novel optical simulation settings. Preliminary results showed excellent agreement between simulation results and experimental measurements. Future work is aimed at extending this approach to optimize CsI screen optic design and sensor structure for achieving higher DQE(f) in cone-beam CT, which uses high kVp.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Effect of resistivity gradient on laser-driven electron transport and ion acceleration

The effect of resistivity gradient on laser-driven electron transport and ion acceleration is investigated using collisional particle-in-cell simulation. The study is motivated by recent proton acceleration experiments [Gizzi et al., Phys. Rev. ST Accel. Beams 14, 011301 (2011)], which showed significant effect of the resistivity gradient in layered targets on the proton angular spread. This effect is reproduced in the present simulations. It is found that resistivity-gradient generation of magnetic fields and inhibition of electron transport is significantly enhanced when the feedback interaction between the magnetic field and the fast-electron current is included. Filamentation of the laser-generated hot electron jets inside the target, considered as the origin of the nonuniform proton patterns observed in the experiments, is clearly suppressed by the resistive magnetic field. As a result, the electrostatic sheath field at the target back surface acquires a relatively smooth profile, which contributes to the superior quality of the proton beams accelerated off layered targets in the experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High Efficiency, Inexpensive Thin Film III-V Photovoltaics using Single-Crystalline-Like, Flexible Substrates

An innovative, non-mainstream approach has been developed to fabricate inexpensive GaAs solar cells directly on epi-ready flexible metal substrates. Using templates made by ion beam assisted deposition (IBAD) and epitaxial germanium films made by Plasma Enhanced Chemical Vapor Deposition (PECVD), epitaxial GaAs films with high opto-electronic and structural quality have been grown on metal substrates using metal organic chemical vapor deposition (MOCVD). Crystallographic out-of-plane and in-plane texture spread less than 1 degree full-width-at-half-maximum (FWHM) was achieved in undoped, n-type and p-type GaAs films as well as in AlGaAs films on metal substrates. Electron mobility of >1300 cm 2 /V-s was attained in GaAs:Si n-type films. Also, hole mobility of >100 cm 2 /V-s was measured in GaAs:Zn films. Consistent doping was obtained in GaAs:Si (10 15 -10 18 cm -3 ), and GaAs:Zn films (10 17 -10 19 cm -3 ), necessary for the active device layers of a GaAs solar cell. Defect reduction techniques (thermal cycling, superlattice structures) were implemented to reduce defect density in GaAs films from 1 × 10 9 cm -2 to 9 × 10 7 cm -2 . Lifetime of 2.3 ns was obtained in AlGaAs/GaAs double-heterostructure device. Solar cells were fabricated based on designs using 1-dimensional and 2-dimensional simulations tailored to the specific properties of the GaAs films on metal substrates. All device fabrication processes (lithography, anti-reflection coating (ARC), device isolation and mesa formation and ohmic metal electrode formation) suitable for III-V solar cell fabrication on metal substrates were fully developed. A bi-layered ARC using ZnS and MgF 2 was used to minimize the reflection over wide range of spectrum. When this ARC was applied after removal of the parasitic absorption layer, the conversion efficiencies were improved up to 11.1% with V oc = ~0.621 V, J sc = ~24.5 mA/cm 2 , and FF = ~0.735. Yet another accomplishment in this project was the development of all electrically-conducting architecture for GaAs solar cells on metal substrates. Biaxial-texture was successfully achieved in all electrically-conducting buffer layer on metal substrate in structure based on IBAD TiN instead of IBAD MgO. The all electrically-conducting Ge/NiSi 2 /TiN/IBAD-TiN/Hastelloy substrate was used to fabricate back contacts for vertically conducting solar cell structures on metal substrates. A metallic resistivity as low as 4.17 μΩ•cm was obtained. A significant improvement of the texture of the Ge template was achieved using a Ag buffer layer between the TiN films. Epitaxial GaAs was successfully grown on the all-electrically-conducting buffer architecture. A Liquid Phase Epitaxy (LPE) method to drastically increase grain size of epitaxial Ge while maintaining the single-crystalline-like texture. Grain size up to 35 µm was achieved in LPE Ge grown on sputtered Ge with a grain size of ~ 1 µm on IBAD template on metal substrate. Epitaxial GaAs was grown on LPE Ge, with an out-of-plane texture of 0.34° compared to 0.98° in GaAs grown on sputter deposited Ge. A model was developed to simulate the effect of grain boundaries as a function of grain size of GaAs films on metal substrates. This model showed that even the very low angle grain boundaries (<1º misorientation) of our GaAs films led to decrease in Voc. Hydrogen plasma passivation treatment is being developed to improve open circuit voltage and the conversion efficiency of GaAs solar cells on flexible substrate.

14 SOLAR ENERGY↗

Back Contact Engineering for Increased Performance in Kesterite Solar Cells

The thin-film photovoltaic absorber Cu 2 ZnSn(S,Se) 4 (CZTSSe) holds considerable promise for large scale conversion of sunlight into electricity. CZTSSe is composed of Earth-abundant elements that exhibit low-toxicities, but improvements in device efficiency have been hampered by difficulties in increasing open circuit voltages (V OC ) due, at least in part, to disorder induced band tailing. We present a method to increase VOC through direct modification of the back contact; our approach involves the separation of fully functioning devices from their Mo/glass substrate to reveal the back CZTSSe surface. Formation of a new back contact consisting of a thermally deposited high work function material (MoO 3 ), together with a higly reflective (Au) capping layer, creates an electrostatic field that drives electrons to the front p-n junction and leads to a decrease in electron-hole recombination. Model simulations indicating an increase in V OC with decreasing absorber thickness are borne out by experiments with devices of varying thicknesses (0.7–2.0 μm). We report VOC increases of up to 49 mV for a 1 μm thick absorber, with even greater increases up to 61 mV when the back CZTSSe surface is etched with bromine-methanol.

14 SOLAR ENERGY↗

Structure and interface chemistry of MoO{sub 3} back contacts in Cu(In,Ga)Se{sub 2} thin film solar cells

Molybdenum oxide (MoO{sub 3}) is considered as a possible primary back contact for Cu(InGa)Se{sub 2} thin film solar cells for its potential as a transparent back contact for superstrate and bifacial devices. MoO{sub 3} films were deposited on Mo or ITO-coated soda lime glass substrates by reactive rf sputtering in an ambient of Ar + O{sub 2} with O{sub 2}/(O{sub 2} + Ar) = 35% on which Cu(In{sub 0.7}Ga{sub 0.3})Se{sub 2} alloy absorber layers were deposited using multi-source elemental evaporation. Scanning Electron Microscopy studies showed uniform coverage of the as-deposited MoO{sub 3} layer and good adhesion was obtained in all cases. X-ray Photoelectron Spectroscopy depth profile analysis showed that MoSe{sub 2} was not formed at the Cu(InGa)Se{sub 2} interface with either the Mo-MoO{sub 3} or ITO-MoO{sub 3} back contacts. Determination of the valence band offsets showed that the MoO{sub 3} layer at the interface changes the energy band alignment with Cu(InGa)Se{sub 2}, producing a primary contact with lower valence band offset than ITO. Cu(In,Ga)Se{sub 2} thin film solar cells prepared using an as-deposited Mo-MoO{sub 3} back contact yielded a best conversion efficiency of 14%, with V{sub OC} = 647 mV, J{sub SC} = 28.4 mA/cm{sup 2}, and FF = 78.1%. Cells with ITO-MoO{sub 3} back contact showed a best efficiency of 12%, with V{sub OC} = 642 mV, J{sub SC} = 26.8 mA/cm{sup 2}, and FF = 69.2%.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Toward Low-Thermal-Budget Hafnia-Based Ferroelectrics via Atomic Layer Deposition

Since the first report of ferroelectricity in fluorite structure oxides a decade ago, significant attention has been devoted to studying hafnia-based ferroelectric material systems due to their promising properties and opportunities. To achieve such ferroelectric fluorite structure oxides at low temperatures (below 400 °C), stabilizing the metastable noncentrosymmetric orthorhombic phase is crucial. This review provides a comprehensive overview of atomic layer deposition (ALD) techniques for obtaining the orthorhombic phase for low-temperature ferroelectric applications. We discuss optimization of the ALD process for synthesizing high-quality, low-temperature crystallizing ferroelectric films, including doping, precursor and oxygen source selection, deposition temperature, and interface engineering. In addition, the techniques for stabilizing the ferroelectric phase by regulating the thermal budget and stress with various annealing methods and stressors are discussed. In conclusion, the review focuses on different techniques to reduce the thermal budget required to acquire ferroelectricity, making hafnia-based ferroelectric materials compatible with back-end-of-line and three-dimensional integration for a variety of future applications, including flexible electronics applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Impact of Interposer Microstructure on Ionic Transport in Liquid-Phase Bicarbonate Electrolysis

The electrochemical reduction of CO 2 (CO 2 RR) is a potentially scalable approach for converting captured carbon dioxide into value-added products. Conventional gas-phase electrolysis systems can suffer from carbonate crossover, which limits the efficiency of the system. Liquid-phase (bi)carbonate electrolysis using bipolar membrane electrode assemblies (BPMMEA) has emerged as a promising alternative. The interposer layer, a porous mass-transport material between the BPM and the catalyst, is an essential component of the MEA, as it allows evolved CO 2 to reach the catalyst surface for reaction. In the absence of this layer, evolved CO 2 generated by the pH swing process at the BPM can be converted back into (bi)carbonate (CO 2 recapture) due to the high bulk pH. Thus, clear design guidelines are needed to maximize CO 2 conversion, minimize CO 2 recapture in the catholyte, and improve energy efficiency. Here, the transport properties of the interposer are systematically characterized by X-ray tomography and symmetric-cell impedance spectroscopy to quantify porosity, tortuosity, and the resulting MacMullin number. We then examine the correlation between these material properties and the electrolyzer performance. We focus on characterizing two commercial porous membrane filters, mixed cellulose ester (MCE) and poly(ether sulfone) (PES).

CO2 electrolysis↗

Magnetostructural Influences of Thin Mg Insert Layers in Crystalline CoFe(B)/MgO/CoFe(B) Magnetic Tunnel Junctions

It is common to find a thin ({approx}0.5 nm) layer of Mg deposited prior to the MgO tunnel barrier in crystalline CoFe(B)/MgO/CoFe(B) magnetic tunnel junctions, due to the improved device performance that results. However, despite their common usage, the reasons why such layers are effective are unclear. We use structures that model the lower electrode of such devices to show that a suitably thick Mg insert layer enhances the crystal quality of both MgO and CoFe(B), permits interfacial oxides to reduce back to a metallic ferromagnetic state, and hence improves magnetic switching of the CoFe(B) electrode, properties which are inextricably linked to device performance.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Tunable bilayer two-dimensional electron gas in LaAlO{sub 3}/SrTiO{sub 3} superlattices

We report magnetotransport properties of double heterointerfaces in LaAlO{sub 3}/SrTiO{sub 3}/LaAlO{sub 3}/SrTiO{sub 3}(001) (LAO/STO/LAO/STO). A strong nonlinearity in the Hall resistivity is found when the temperature is below 80 K. This effect is attributed to multichannel conduction of interfacial charges generated in double heterostructures of LAO/STO where two-dimensional electron gas (2DEG) is produced. The multichannel conduction is confirmed by back gating modulation of Hall effect. Our result suggests the possibility to achieve coupled bilayer 2DEG layers in LAO/STO superlattices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Strength, stiffness, and microstructure of Cu(In,Ga)Se{sub 2} thin films deposited via sputtering and co-evaporation

This work examines Cu(In,Ga)Se{sub 2} thin films fabricated by (1) selenization of pre-sputtered Cu-In-Ga and (2) co-evaporation of each constituent. The efficiency disparity between films deposited via these two methods is linked to differences in morphology and microstructure. Atomic force microscopy and scanning electron microscopy show that selenized films have rougher surfaces and poor adhesion to molybdenum back contact. Transmission electron microscopy and electron energy loss spectroscopy revealed multiple voids near the Mo layer in selenized films and a depletion of Na and Se around the voids. Residual stresses in co-evaporated films were found to be ∼1.23 GPa using wafer curvature measurements. Uniaxial compression experiments on 500 nm-diameter nanopillars carved out from co-evaporated films revealed the elastic modulus of 70.4 ± 6.5 GPa. Hertzian contact model applied to nanoindentation data on selenized films revealed the indentation modulus of 68.9 ± 12.4 GPa, which is in agreement with previous reports. This equivalence of the elastic moduli suggests that microstructural differences manifest themselves after the yield point. Typical plastic behavior with two distinct failure modes is observed in the extracted stress-strain results, with the yield strength of 640.9 ± 13.7 MPa for pillars that failed by shearing and 1100.8 ± 77.8 MPa for pillars that failed by shattering.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗