Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Vehicle testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Fourier Analysis and Design of a Shielded 120kW Inductive Wireless System

High-power inductive wireless power transfer (WPT) systems for EVs are designed to meet specifications such as stray field, power level, efficiency, misalignment tolerance, and ground clearance. These metrics are all heavily influenced by the coil geometry. Herein this paper proposes a coil design method based on the Fourier Analysis Method (FAM) which is an analytical method for directly designing coil geometries to meet stray field and power level requirements through an optimization of Fourier basis function coefficients. In this work, two 120 kW WPT proof-of-concept demonstrators with low stray field and high efficiency are built from FAM optimization results to validate the models and show the impact of the FAM design process. Experimental validation of the Gen. 2 demonstrator at 120 kW output power resulted in a measured DC/DC efficiency of 97.2% at alignment with a 125 mm airgap. At the 120 kW test point, the stray fields 80 cm away from the center of the airgap between the coil assemblies were 3.4 µT(rms) on the X-axis and 3.5 µT(rms) on the Y-axis, much lower than the 27 µT(rms) ICNIRP limit.

42 ENGINEERING↗
DOE OSTI2024

Hydrogen Leak Modeling for Development of Smart Distributed Monitoring Under Unintended Releases

Hydrogen is a versatile and clean energy carrier that can be produced from various renewable sources such as wind, solar, and hydropower. Hydrogen has the potential to play a crucial role in decarbonizing industrial processes that are currently reliant on fossil fuels and provide long-duration and/or seasonal energy storage to enable electricity decarbonization. Hydrogen can also be used as a fuel for fuel cell vehicles, providing a zero-emission alternative to traditional internal combustion engines. DOE launched the Hydrogen Energy Earthshot (Hydrogen Shot) in June 2021 to reduce the cost of clean hydrogen by 80% to $1 per 1 kilogram in 1 decade ("1 1 1"). While promising, Hydrogen is highly-flammable, and in the presence of oxygen, it can form explosive mixtures. . Therefore, understanding leak scenarios is essential to evaluate and mitigate the safety risks associated with potential hydrogen leaks. An increased understanding of leak behavior, and having tools to model leaks, can help assess how hydrogen would disperse in different environments, influencing emergency response plans and safety measures, and identify potential issues with materials and design systems that can withstand the challenges posed by hydrogen. Recently, researchers have attempted to study hydrogen leaks for development of risk management strategies. However, the focus has been on closed or semi-closed spaces like storage rooms, vehicles, garages, and fueling stations - all promising locations for future hydrogen infrastructure. In this presentation, the modeling environment extends the span of research further by modeling hydrogen leak in an outdoor, open space. We will present the key challenges with modeling hydrogen leaks in an uncontrollable environment, how they were handled, and how modeling results informed sensor selection and placement. A Hydrogen research facility at the National Renewable Energy Laboratory (NREL) was used as a case study to model hydrogen leaks. In the future, Hydrogen wide area detection methodologies will be developed and tested at this site to monitor for unintended and operational hydrogen releases. The data generated from modeling will be used to develop a predictive model to detect hydrogen leak location based on concentration measured by sensors in this open space. Furthermore, the facility was also chosen because controlled hydrogen releases can be performed. A computational fluid dynamics (CFD) based modeling approach was taken to model hydrogen leak. The full-scale hydrogen facility was modeled with a large ambient domain. The electrolyzer at the facility can produce a controlled release rate of 27 kg-H2/hr. Site-specific atmospheric and weather condition data such as wind direction, wind speed at various altitudes, and temperature were used as inputs to the model. To capture the variability of weather conditions, a subset of the weather conditions experienced during daytime hours without precipitation over the course of three months was generated; using established data clustering techniques, a total of 100 condition sets were chosen. The results show statistical distributions and ranges of hydrogen concentrations at locations throughout the domain. These distributions are compared to experimental data from a constant mass flow, controlled hydrogen release at the facility. The stochastic wind conditions of the release make direct validation difficult, therefore, statistical comparison approaches were used. Wind conditions are found to significantly impact the release behavior, including direction and concentration. Sensor selection and placement is proposed for the facility and is now based on release behavior predicted for the facility given its weather patterns; this is much more informed than without the modeling results. The methodology and analysis procedure can be translated to other facilities using modified geometries and site-specific weather conditions. Hydrogen holds great promise as a renewable energy fuel, but ensuring safety in its production, storage, and use is paramount. Studying potential leak scenarios in an open space will help develop sensors to detect hydrogen on a large spectrum of concentration and eventually build a smart distributed monitoring system.

CFD↗
DOE OSTI2021

AN AUTOMATED ANCHORING SYSTEM FOR AN UNMANNED SURFACE VEHICLE

The goal of this thesis is to simulate, design and build an automated device that allows unmanned vessels to anchor themselves in specified locations while being United States Coast Guard Navigation Rules compliant. This is a part of a larger project funded by the U.S. Department of Energy for Florida Atlantic University to build an unmanned platform with an Undershot Water Wheel on it. By simulating the environment of the South Florida Intercoastal Water Ways, forces acting on the line, anchor and the vessel are analyzed. These forces are used as the guide for the design and build of a line locking mechanism that takes the tension off the winch and a sensor package to monitor the environment the platform is in as well as control of the system. Based off experimental testing, the system was successful in handling all emulated environments with loads exceeding 150lbs of tension.

Fosbrook, Amanda↗
DOE OSTI2023

Key Considerations in Assessing the Safety and Performance of Camera-Based Mirror Systems

Camera-based mirror systems (CBMSs) are a relatively new technology in the automotive industry, and much of the United States’ medium- and heavy-duty commercial fleet has been reluctant to convert from standard glass, or “west coast”, mirrors to CBMSs. CBMSs have the potential to reduce the number of truck and passenger vehicle incidents, improving overall fleet safety. CBMSs also have the potential to improve operational efficiency by improving aerodynamics and reducing drag, resulting in better fuel economy, and improving maneuverability. Improvements in overall safety are also possible; the field of view for the driver is potentially 360° with the addition of trailer cameras, allowing for visibility of the rear of the trailer and the front of the truck. These potential improvements seem promising, but the literature on driver surveys clearly shows that there is reluctance to adopt this technology for many reasons. Additionally, more robust testing in the laboratory and in the field is necessary to determine whether CBMSs are adequate to replace standard mirrors on trucks. This analysis provides an overview of key research questions for CBMS testing based on the current literature on the topic (surveys, standards, and previous testing). The purpose of this analysis is to serve as guidance in developing further testing of CBMSs, especially testing involving human subjects.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2021

Nuclear Safeguards: Feature Extraction for Machine Learning Enrichment Analysis of UF 6 Cylinders

With the increasing international interest in using nuclear material as sources of energy, comes the growing concern that we may see an increase in proliferation threats. Uranium hexafluoride (UF 6 ) is used in the nuclear fuel cycle for uranium enrichment. Inspectors from the International Atomic Energy Agency (IAEA) monitor the enrichment levels of UF 6 stored in transportation cylinders, to ensure the enrichments match that of a facility operator’s declarations. However, only a characteristic subset of UF 6 cylinders can be measured by inspectors from the IAEA during these inspections. In turn, the inspector may not identify a cylinder whose enrichment levels do not match the facility declarations. Therefore, our team attempts to develop a machine learning network that could determine the enrichment percentage of cylinders as they enter and exit facilities. The machine learning model must be robust against spectral variations due to factors that are internal and external to the UF 6 cylinder. Such factors include but are not limited to the speed and distance of the moving vehicle, cylinder type, cylinder orientation, and fill level. Many features in the spectral continuum can be used to identify and correct for some of these variations. As a consequence, the model must extract numerous features in the continuum. We investigate new approaches in continuum subtraction to verify enrichment percentage: interpolation and extrapolation of lines at the notable characteristic spectral peaks. It was determined that there was no clear answer on which method proved superior, therefore the decision was made to implement both new methods into the current codebase. We currently rely on synthetic training and testing data to analyze the results and fine tune our models but hope to test the system on measured data soon.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2024

300_underground robot (final research report)

Recent advancements in mobile robotics have displayed impressive capabilities in traversing and accessing areas that are inaccessible to humans either due to the characteristics of the environment or potential hazards. Furthermore, these advancements within the field of mobile robotics, more specifically uncrewed ground vehicles (UGVs), give the ability to potentially survey, observe, and map these inaccessible areas for humans. However, one of the most challenging areas to implement this technology is underground environments. The main challenge with implementing this technology in underground environments is the dependence on either GPS or RF communication for UGVs to navigate properly. Therefore, in order to properly demonstrate the mapping capabilities of the UGV this challenge must be resolved. The overall goal of this study is to demonstrate the mapping capabilities of a UGV while addressing this challenge and documenting the implementation and testing phase of the robot. The proposed solution to this challenge is to implement a SLAM algorithm onto the main computational device of the UGV utilizing the Robot Operating System (ROS). The algorithm is the open-source software package Slam Toolbox developed by Steve Macenski. Furthermore, the sllidar_ros2 package from Slamtec will be used to gather the lidar data from an A3M1 2D lidar. A separate program will be created to gather odometry information for our UGV robot. All of these software packages will run together in a Docker environment. Through working on this project I have developed a better understanding of the world of robotics/autonomous systems, especially with applications such as navigation and mapping. Furthermore, through this project, I have been given exposure to how research is conducted within a DOE lab setting. As robotics/autonomous systems become more advanced it's important to pursue more avenues of research such as this project as it will ensure the development of our capabilities.

42 ENGINEERING↗
DOE OSTI2024

Power Layout Design of a GaN HEMTs-Based High-Power High-Efficiency Three-Level ANPC Inverter for 800 V DC Bus System

Multiple commutation paths exist for switching devices in a three-level active neutral point clamped (3L-ANPC) inverter operation based on the selected switching state and current direction. In addition, the capacitive coupling path of the nonswitching device is a key design aspect for enabling high voltage and high current operation of gallium nitride (GaN) switches in 3L-ANPC topology. A comprehensive study of the switching transient events of inner, outer, and clamping devices of 3L-ANPC is presented in this article. The commutation mechanisms for worst-case transient voltage overshoots (TVOs) are identified. A simplified equivalent circuit model is presented to determine the design criteria for the power layout structure's parasitic inductances. A power layout strategy satisfying the design criteria is then proposed using an insulated metal substrate power printed circuit board (PCB) to enable efficient high-power operation. The proposed design minimizes the commutation and capacitive coupling path inductances to 6 nH and 11.5 nH, respectively. This enables the fast switching operation of GaN HEMTs at 800 V dc, 36 A with a low TVO of 31% verified through experimental three-level double pulse test results. Experimental evaluation of a three-phase 3L-ANPC hardware prototype based on the proposed power layout shows 99% efficiency at 800 V, 9.5 kVA and 50 kHz switching frequency. The proposed design achieves a low case-to-ambient thermal resistance of 2.3 °C/W.

42 ENGINEERING↗
DOE OSTI2023

Mitigating Corrosion in Mg Sheet in Conjunction with a Sheet-Joining Method that Satisfies Structural Requirements within Sub-assemblies

This work was undertaken as a LightMAT project funded by the DOE-Vehicles Technology Office. The goal of this work was to develop corrosion protection strategies that simultaneously mitigate corrosion and achieve Class-A surface finish for Mg components in automotive applications. While automotive metals such as steel and aluminum are protected against corrosion through a variety of coating schemes/packages, the efficacy of these existing coating schemes for Mg and Mg- joints is not clear and needs to be determined. Therefore, five commercially available coating schemes and two joining techniques (riveting and Arplas resistance spot welding) were evaluated. The corresponding individual Mg sheet coupons or Mg/Mg joint test coupons were provided by Magna that were then corrosion tested at PNNL using ASTM B117 procedure. The microstructures and mechanical properties of the coupons were analyzed to determine the effectiveness of the joining and corrosion mitigation strategies. Of the coating schemes evaluated, Henkel Bonderite MgC 2.0 pre-treatment + E-coat showed the best corrosion protection and surface finish for individual Mg coupons and Arplas resistance spot welded coupons. However, the strength of Mg/Mg welded joint was reduced after corrosion testing due to some corrosion at the weld nugget. Mg/Mg rivet joints in conjunction with Chemetall oxisilan pre-treatment + polyurethane coating showed good corrosion resistance and some discoloration on the surface finish. Coating schemes comprising pre-treatment with Alodine 5200 + E-coat or Bonderite 1455 + polyurethane coating, in conjunction with Al rivet joints, showed significant corrosion and extensive discoloration of the surface. We anticipate that the results from this work will provide useful guidance to the automotive industry in selecting the appropriate combinations of corrosion protection coatings and joining techniques to fabricate light-weight Mg-based automotive components.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ultrasonic Nondestructive Diagnosis of Cylindrical Batteries Under Various Charging Rates

Lithium-ion batteries have been used increasingly as electrochemical energy storage systems for electronic devices and vehicles. It is important to accurately estimate the state of charge (SoC) of a battery management system to control the battery operation to optimize performance, lifetime, and safety. The current work experimentally leverages ultrasonic diagnostic technology to investigate the SoC of lithium-ion batteries during the charge/discharge processes. A cylindrical-type nickel-cobalt-aluminum (NCA)–based 2500mAh 20A (INR18650-25R) battery was used for ultrasonic measurements with various charge/discharge rates of C/10.4, C/5.2, and C/1.3 at constant currents. The ultrasonic signals were analyzed for extracting wave velocity and wave attenuation. For all the testing rates, wave velocity increased in the charge process and decreased in the discharge process. Further, velocity profiles corresponding to lower rates of C/10.4 and C/5.2 exhibited primary peaks at the maximum SoCs, whereas the absolute wave velocity of C/1.3 rate showed primary peaks that occurred slightly after the SoC peak, indicating a delayed maximum Young's modulus. The wave attenuation computed for the C/10.4 rate had local maxima in the charge and discharge processes and depicted negative correlations with SoC, ranging from 0% to 18%, and positive correlations with SoC from 18% to 85%. On the other hand, the wave attenuation curves of the C/1.3 rate showed no local peaks and had negative correlations with SoC, ranging from 0% to 28%, and positive correlations with SoC ranging from 28% to 53%.

25 ENERGY STORAGE↗
DOE OSTI2021

Development of cathode-electrolyte-interphase for safer lithium batteries

Accompanied by the adoption of aggressive cathodes to continuously improve batteries energy density, enhancing their safety is becoming increasingly urgent for the electric vehicle development. In-situ controllable formation of robust cathode-electrolyte interphase (CEI) with high inorganic content seems to be the most promising strategy to address the thermal runaway concerns. Moreover, the in-situ formation strategy via suitable electrolyte replacement or electrolyte additives is extremely simple yet effective, especially for industrial manufacture of batteries. Here, this paper briefly reviews recent advanced CEIs formed by conventional carbonate-based electrolytes, fluorinated electrolytes, concentrated electrolytes, and solid state electrolytes. The focus on the thermal stability of the cathodes after CEI modification, and at the same time conduct safety tests at the material, cell, and module levels for comprehensive evaluation are encouraged. The review will provide inspiration for future developments in battery safety and push forward the practical applications of newly developed high-energy density batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Critical Barriers to Successful Implementation of Earth-Abundant, Mn-Rich Cathodes for Vehicle Applications and Beyond: The Effect of Particle Morphology

As the search for improved and next-generation cathodes continues, it is clear that a deeper understanding of synthesis–structure–electrochemical property relationships is of critical importance. The effects of primary and secondary particle morphologies on various transition metal oxides have been studied, but new findings are still being reported. To date, few studies have focused on the effects of particle morphologies on Li- and Mn-rich oxides (>50% Mn) and even fewer studies have focused on the influence over key properties such as electrode-level impedance. In this study, we report the effects of particle morphologies on the area-specific-impedance (ASI) and thermal behavior of Li- and Mn-rich oxides. Samples with a fixed, layered–layered–spinel (LLS), composition were synthesized with differing primary morphologies and tested under standardized, full-cell protocols. The results suggest that smaller primary particle size (i.e., higher surface area) leads to lower overall ASI, a delay in the increasing impedance at low states-of-charge (SOCs), and surprisingly, improved thermal behavior.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

The impacts of COVID-19 on clean energy labor markets: Evidence from multifaceted analysis of public health interventions and COVID-health factors

COVID-19 pandemic has affected clean energy labor market. Using real-time job vacancy data, this study analyzes the impacts of the pandemic on the U.S. clean energy labor market in 2020, including biomass, energy efficiency (EE), electric vehicle (EV), power/microgrid, solar, and wind industries. This study identifies how COVID-health factors and public health interventions influence clean energy job availability during the early COVID pandemic. Overall, California had the most energy jobs and experienced a significant decrease in April 2020. EV and solar had the highest percentages of job vacancies during the pandemic in general. Still, lockdowns had the most severe influence on EE and wind jobs. Stay-at-home orders negatively affected clean energy job vacancies in biomass, EV, power/microgrid, and wind. Social-gathering restrictions, however, did not have much influence. Increased COVID tests at the state level had the strongest and most positive influence on clean energy job postings, indicating the importance of a state's ability to manage public health infrastructure or crisis issues. COVID hospitalizations negatively influenced the job vacancies in biomass and wind but did not affect the other four sectors; conversely, as COVID death numbers increased, the number of jobs in biomass, EV, power grid, solar, and wind decreased, but not in EE jobs.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Value-based Insights from the Implementation of Hierarchical Control for Energy Savings and Demand Response in Residential Premises

As the adoption of distributed energy resources and electric vehicles at residential customer premises increases exponentially, behind-the-meter assets can be utilized to achieve energy cost reduction and demand response through coordination and control strategies. A hierarchical control architecture from the utility headend to residential premises is implemented to attain these objectives. This paper extracts the values from the development, implementation, and deployment of that control hierarchy. The development of the control philosophy is built upon the existing advanced metering infrastructure, communication protocols, and industry-compatible application programming interfaces. Results are presented visually with analytical insights by utilizing the data from hardware-in-the-loop testing and simulation analysis out of the collected data from the field.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Corrosion Protection and Dissimilar Material Joining for Next Generation Lightweight Vehicles

The Arconic Technology Center working with Honda R&D Americas, LLC and the Ohio State University evaluated the corrosion performance of several multi-material conditions and demonstrated the production worthiness of the Resistance Spot Riveting (RSR™) process. RSR is a new technology being developed by Howmet Fastening Systems (formerly Arconic, Inc.) that employs a fastener that is installed using conventional resistance spot welding equipment to produce multi-material joints. The goal of the 3-year project was to demonstrate the use of RSR to join aluminum to steel and aluminum to carbon fiber composites on a prototype scale. Deployment of this technology would help the automotive industry achieve an additional 10 to 20% weight reduction over high strength steels. These weight-savings to the body in white generally translates to 2.5-5.0% of overall vehicle curb weight. The resulting total weight-savings could provide a 1.5% to 3.0% total improvement in fuel efficiency for vehicles that incorporate RSR for multi-material joining. The RSR technology addresses several production barriers to achieving DOE’s fuel efficiency targets including eliminating the need of additional capital for new joining technologies and the flexibility to process conventional steel and multi-material structures with the same equipment. Additionally, the trend towards ultra-high strength steels limits the availability of conventional joining technologies that can effectively process these multi-material combinations. In order to accomplish these goals, the following program milestones were completed by the team: 1) Developed RSR process parameters, producing multi-material joints for mechanical testing and corrosion assessments. 2) Conducted corrosion evaluation of RSR and baseline joints assembled between automotive type aluminum alloys, steels, and carbon fiber using several corrosion mitigation strategies. 3) Developed a production ready feed system and integrate into a robotic resistance spot welding station to simulate automotive production conditions. 4) Produced demonstration assemblies for testing and evaluation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

SCALED-PRODUCTION OF RARE EARTH OXIDES AND CRITICAL MATERIALS FROM COAL-BASED SOURCES

A projected exponential increase in the production of electric vehicles and high-end advanced technologies including those used in the defense industrial is expected to require nearly double the amount of rare earth elements (REEs) and critical elements currently available worldwide. As such, recovery from secondary sources such as coal and coal byproducts may be needed to meet the increased demand. A project has been initiated to evaluate methods and technologies integrated in an existing rare earth pilot plant that have the potential to improve the economics of extracting rare earths and critical materials from coal-based materials. This presentation will provide details about the technologies and results from pilot plant testing.

Honaker, Rick Q↗
DOE OSTI2021

DISTRIBUTION TRANSFORMER ASSET MONITORING ON THE GRID EDGE USING SMART SENSOR DATA

As new loads such as rooftop photovoltaics, electric vehicles and other distributed energy resources become commonplace on the distribution grid, the stress on already aging assets begins to escalate. This increased loading and changing dynamics can exacerbate failure rates. While traditional monitoring efforts focus on transmission and generation assets, utilities are now beginning to pay close attention to distribution assets in order to increase reliability indices and reduce cost from unexpected outages. This research develops low-cost and scalable methods to monitoring the health of a critical distribution grid asset: the service transformer. Existing methods in literature are either invasive and thus difficult to implement or require the device to be tested offline in an expensive lab setting. Data from the ubiquitous smart meter as well as a novel Bluetooth based transformer monitor are leveraged to automatically notify the utility of deteriorating or damaged transformers. Voltage, temperature, and vibration are some of the signals measured and analyzed by the proposed algorithms to predict transformer failures. Furthermore, these algorithms are designed to keep the implementation and processing costs low by taking advantage of edge computing where possible.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Evaluation of H-Canyon Ventilation Exhaust Tunnel Inspection at the Savannah River Site - 20052

The Department of Energy (DOE) H-Canyon Facility at the Savannah River Site (SRS) is operated by Savannah River Nuclear Solutions (SRNS). The Facility Structural Integrity Program [1] provides a process to inspect, evaluate, and document the conditions of passive safety related structural systems and components, their degradation mechanisms and their impact on the safety envelope. The Structural Integrity Program performs periodic visual inspections to confirm the systems and components can perform their safety function and recommend corrective actions before the function is compromised. The H-Canyon Exhaust Tunnel is part of the H-Canyon Ventilation System and is periodically inspected under the Structural Integrity Program. The Tunnel performs a Safety Class passive design feature function that is available 100% of the time. The underground reinforced concrete Tunnel directs Canyon process air from the Canyon to the Sand Filter System. The radiological and chemical airborne activity coupled with the physical configuration of the tunnel precludes a manned entry into the tunnel to perform the inspection. Unlike active systems that can be subjected to physical testing to confirm capability, qualification calculations, including modeling, is performed to assess passive design feature capabilities relative to operational, accident and natural phenomena hazards events. Input for these calculations come from knowledge of field conditions, design drawings and conservative assumptions. The knowledge of field conditions comes from concrete and soil testing activities as well as inspection data. The use of cameras on crawlers to obtain inspection data and how that data is used in qualification calculations is the focus of this discussion. Remote Tunnel inspections have been performed using cameras on a stick, referred to as pole cameras, prior to Calendar Year 2003 (CY2003). Since CY2003, six camera equipped crawlers have been used. Crawlers have evolved and improved by incorporating lessons learned from the previous inspections. The latest 2019 crawler successfully traveled the entire length of the tunnel between the Canyon and Sand Filter System and captured images that were previously unseen, thus providing key visual data for the Structural Integrity Program report [2]. The inspection data serves as 1) input to qualification calculations, 2) validates current conditions remain bounded by qualification calculations, and 3) documents a record of change over time. This data is vital for the effective evaluation of the tunnel structure and aids with predicting the life cycle service life safety envelope to protect the public, environment, and facility worker. The goal of the 2019 deployment was to use a more robust vehicle to ensure travel over obstacles, perform the inspection with higher resolution cameras, and have the ability to elevate the cameras to view surfaces previously obscured by abandon-in-place ducts in the tunnel. The inspection information will serve to strengthen the input basis for qualification calculations, versus using excessive conservative calculation assumptions. This 2019 inspection was compared with previous crawler visual evidence to identify change over time to project remaining service life and confirm field conditions remain bounded by qualification calculations. The results of the 2019 Exhaust Tunnel inspection continue to improve and provide a firm basis to make sound engineering judgements regarding tunnel capability and approaches in projecting remaining service life with an aging system and component. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Recent developments in Pt–Co catalysts for proton-exchange membrane fuel cells

Development of Pt-based oxygen reduction reaction catalysts with high efficiency and high durability is central to the application of proton-exchange membrane fuel cell systems. Pt–Co bimetallic catalysts have drawn extensive attention owing to their capability of delivering high performance and long lifetime for fuel cell applications including light-duty and heavy-duty vehicles. However, further improvements in durability and performance are needed to meet market requirements. To fully exploit the potential of Pt–Co catalysts, new insights into the relationship between catalyst properties and fuel cell performance and durability are needed, and more effective methods to tailor the features of Pt–Co catalysts need to be developed. This review provides a summary and perspective on recent efforts, including work on customizing the Pt shell and Pt:Co ratio, tailoring the crystal structure, and improving carbon support properties, with a particular emphasis on mechanisms leading to enhancement of mass activity, power density, and durability in membrane electrode assembly testing.

25 ENERGY STORAGE↗