Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TiN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1944

The Surface Structure of Ground Metal Crystals

The changes produced on metallic surfaces as a result of grinding and polishing are not as yet fully understood. Undoubtedly there is some more or less marked change in the crystal structure, at least, in the top layer. Hereby a diffusion of separated crystal particles may be involved, or, on plastic material, the formation of a layer in greatly deformed state, with possible recrystallization in certain conditions. Czochralski verified the existence of such a layer on tin micro-sections by successive observations of the texture after repeated etching; while Thomassen established, roentgenographically by means of the Debye-Scherrer method, the existence of diffused crystal fractions on the surface of ground and polished tin bars, which he had already observed after turning (on the lathe). (Thickness of this layer - 0.07 mm). Whether this layer borders direct on the undamaged base material or whether deformed intermediate layers form the transition, nothing is known. One observation ty Sachs and Shoji simply states that after the turning of an alpha-brass crystal the disturbance starting from the surface, penetrates fairly deep (approx. 1 mm) into the crystal (proof by recrystallization at 750 C).

Boas, W.↗
NASA NTRS2000

Erosion Coatings for High-Temperature Polymer Composites: A Collaborative Project With Allison Advanced Development Company

The advantages of replacing metals in aircraft turbine engines with high-temperature polymer matrix composites (PMC's) include weight savings accompanied by strength improvements, reduced part count, and lower manufacturing costs. Successfully integrating high-temperature PMC's into turbine engines requires several long-term characteristics. Resistance to surface erosion is one rarely reported property of PMC's in engine applications because PMC's are generally softer than metals and their erosion resistance suffers. Airflow rates in stationary turbine engine components typically exceed 2.3 kg/sec at elevated temperatures and pressures. In engine applications, as shown in the following photos, the survivability of PMC components is clearly a concern, especially when engine and component life-cycle requirements become longer. Although very few publications regarding the performance of erosion coatings on PMC's are available particularly in high-temperature applications the use of erosion-resistant coatings to significantly reduce wear on metallic substrates is well documented. In this study initiated by the NASA Glenn Research Center at Lewis Field, a low-cost (less than $140/kg) graphite-fiber-reinforced T650 35/PMR 15 sheet-molding compound was investigated with various coatings. This sheet-molding compound has been compression molded into many structurally complicated components, such as shrouds for gas turbine inlet housings and gearboxes. Erosion coatings developed for PMC s in this study consisted of a two-layered system: a bondcoat sprayed onto a cleaned PMC surface, followed by an erosion-resistant, hard topcoat sprayed onto the bondcoat as shown in following photomicrograph. Six erosion coating systems were evaluated for their ability to withstand harsh thermal cycles, erosion resistance (ASTM G76 83 "Standard Practice for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets") using Al2O3, and adhesion to the graphite fiber polyimide composite (ASTM D 4541 95 "Pull Off Strength of Coatings"). Glenn and Allison Advanced Development Company collaborated to optimize erosion coatings for gas turbine fan and compressor applications. All the coating systems survived aggressive thermal cycling without spalling. During erosion tests (see the final photo), the most promising coating systems tested had Cr3C2-NiCr and WC-Co as the hard topcoats. In all cases, these coating systems performed significantly better than that with a TiN hard topcoat. When material depth (thickness) loss is considered, the Cr3C2-NiCr and WC-Co coating systems provided, on average, an erosion resistance 8.5 times greater than that for the uncoated PMR 15/T650 35 composite. Similarly, Cr3C2-NiCr and WC-Co coating systems adhered to the PMC substrate during tensile tests significantly better than systems containing a TiN topcoat. Differences in topcoats of Cr3C2-NiCr and WC-Co were determined by considering issues such as cost and environmental impact. The preferred erosion-resistant coating system for PMR 15/T650 35 has WC-Co as the hard topcoat. This system provides the following benefits in comparison to the coating system with Cr3C2-NiCr topcoat: lower powder material cost (15 to 20 percent), environmentally friendly materials (Cr3C2-NiCr is hazardous), and higher deposition yield (10 to 15 percent), which results in less waste.

Sutter, James K.↗
NASA NTRS1988

Lead-acid battery construction

The power characteristics of a lead-acid battery are improved by incorporating a dispersion of 1 to 10% by weight of a thermodynamically stable conductivity additive, such as conductive tin oxide coated glass fibers (34) of filamentary glass wool (42) in the positive active layer (32) carried on the grid (30) of the positive plate (16). The avoiding of positive plate reversal to prevent reduction of the tin oxide is accomplished by (a) employing an oversized positive plate and pre-charging it; (b) by pre-discharging the negative plate; and/or (c) by placing a circuit breaker (26) in combination with the plates (16, 18) and terminals (22, 24) to remove the load when the voltage of the positive plate falls below a pre-selected level.

Rowlette, John J.↗
NASA NTRS1985

Unitary plate electrode

The unitary electrode (10) comprises a porous sheet (12) of fiberglass the strands (14) of which contain a coating (16) of conductive tin oxide. The lower portion of the sheet contains a layer (18) of resin and the upper layer (20) contains lead dioxide forming a positive active electrode on an electrolyte-impervious layer. The strands (14) form a continuous conduction path through both layers (16, 18). Tin oxide is prevented from reduction by coating the surface of the plate facing the negative electrode with a conductive, impervious layer resistant to reduction such as a thin film (130) of lead or graphite filled resin adhered to the plate with a layer (31) of conductive adhesive. The plate (10) can be formed by casting a molten resin from kettle (60) onto a sheet of glass wool (56) overlying a sheet of lead foil and then applying positive active paste from hopper (64) into the upper layer (68). The plate can also be formed by passing an assembly of a sheet ( 80) of resin, a sheet (86) of sintered glass and a sheet (90) of lead between the nip (92) of heated rollers (93, 95) and then filling lead oxide into the pores (116) of the upper layer (118).

Rowlette, John J.↗
NASA NTRS1996

Catalytic process for formaldehyde oxidation

Disclosed is a process for oxidizing formaldehyde to carbon dioxide and water without the addition of energy. A mixture of formaldehyde and an oxidizing agent (e.g., ambient air containing formaldehyde) is exposed to a catalyst which includes a noble metal dispersed on a metal oxide which possesses more than one oxidation state. Especially good results are obtained when the noble metal is platinum, and the metal oxide which possesses more than one oxidation state is tin oxide. A promoter (i.e., a small amount of an oxide of a transition series metal) may be used in association with the tin oxide to provide very beneficial results.

Kielin, Erik J.↗
NASA NTRS2006

Thermal Cycle Reliability of PBGA/CCGA 717 I/Os

Status of thermal cycle test results for a nonfunctional daisy-chained peripheral ceramic column grid array (CCGA) and its plastic ball grid array (PBGA) version. both having 560 I/Os. were presented in last year's conference. Test results included environmental data for three different thermal cycle regimes (-55 C/125 C, -55 C/100 C, and -50 C /75 C). Update information on these - especially failure type for assemblies with high and low solder volumes-were presented. The thermal cycle test procedure followed those recommended IPC-9701 for tin-lead solder joint assemblies. Revision A of this specification covers guideline thermal cycle requirements for Pb-free solder joints. Some background information discussed during release of this specification with its current guideline recommendations were also presented. In a recent reliability investigation a fully populated CCGA with 717 I/Os was also considered for assembly reliability. evaluation. The functional package is a field-programmable gate array that has much higher processing power than its previous version. This new package is smaller in dimension, has no interposer, and has a thinner column wrapped with copper for reliability improvement. This paper will also present thermal cycle test results for this package assembly and its plastic version with 728 I/Os. both of which were exposed to three different cycle regimes. Two cycle profiles were those specified by IPC- 9701A for tin-lead, i.e. -55 to 100 C and -55 to 125 C and one was a cycle profile specified by Mil-Std-883, i.e.. -65 C/150 C which is generally used for ceramic hybrid packages. Per IPC-9701 A, test vehicles were built using daisy chain packages and were continuously monitored. The effects of many process and assembly variables-including corner staking commonly used for improving resistance to mechanical loading such as drop and vibration loads--were also considered as part of the test matrix. Optical photomicrographs were taken at various thermal cycle intervals to document damage progress and behavior. Representative samples of these along with cross-sectional photomicrographs at higher magnification taken by scanning electron microscopy (SEM) to determine crack propagation and failure analyses for packages are also presented.

staking↗
NASA NTRS2010

Environmental Regulations as Drivers of Materials Obsolescence

This slide presentation reviews the operations of the Principal Center for Regulatory Risk Analysis and Communication (RRAC-PC) and the impact of environmental regulations in making some materials obsolete. The center is NASA's resource for identifying and managing risks associated with changing environmental regulations. To this end the center acts as an regulatory early warning system, to review track and analyze emerging regulations, collaborate with the technical community on regulatory risk analysis and interpretation and to represent NASA's interests to the regulatory agencies. Regulations frequently result in making some materials unavailable forcing a change to another material. Processes may also be changed due to environmental regulations. For example some items that were sprayed with a chemical may now have to be painted or dipped with the chemical. Sometimes a regulation changes the use of a certain product, which does not affect the usage on Earth, but has significant implications in space. An example of this is the use of lead-free solders of basically tin, which don't appear to have any problem on Earth, but in space applications tin whiskers have resulted in several confirmed satellite failures.

Scroggins, Sharon↗
NASA NTRS2012

Lead-Free Experiment in a Space Environment

This Technical Memorandum addresses the Lead-Free Technology Experiment in Space Environment that flew as part of the seventh Materials International Space Station Experiment outside the International Space Station for approximately 18 months. Its intent was to provide data on the performance of lead-free electronics in an actual space environment. Its postflight condition is compared to the preflight condition as well as to the condition of an identical package operating in parallel in the laboratory. Some tin whisker growth was seen on a flight board but the whiskers were few and short. There were no solder joint failures, no tin pest formation, and no significant intermetallic compound formation or growth on either the flight or ground units.

Blanche, J. F.↗
NASA NTRS2015

Catalyst for Decomposition of Nitrogen Oxides

This invention relates generally to a platinized tin oxide-based catalyst. It relates particularly to an improved platinized tin oxide-based catalyst able to decompose nitric oxide to nitrogen and oxygen without the necessity of a reducing gas.

Schryer, David R.↗
NASA NTRS2016

Solar Array at Very High Temperatures: Ground Tests

Solar array design for any spacecraft is determined by the orbit parameters. For example, operational voltage for spacecraft in Low Earth Orbit (LEO) is limited by significant differential charging due to interactions with low temperature plasma. In order to avoid arcing in LEO, solar array is designed to generate electrical power at comparatively low voltages (below 100 volts) or to operate at higher voltages with encapsulation of all suspected discharge locations. In Geosynchronous Orbit (GEO) differential charging is caused by energetic electrons that produce differential potential between the coverglass and the conductive spacecraft body in a kilovolt range. In such a case, the weakly conductive layer over coverglass, indium tin oxide (ITO) is one of the possible measures to eliminate dangerous discharges on array surface. Temperature variations for solar arrays in both orbits are measured and documented within the range of minus150 degrees Centigrade to plus 1100 degrees Centigrade. This wide interval of operational temperatures is regularly reproduced in ground tests with radiative heating and cooling inside a shroud with flowing liquid nitrogen. The requirements to solar array design and tests turn out to be more complicated when planned trajectory crosses these two orbits and goes closer to the Sun. The conductive layer over coverglass causes a sharp increase in parasitic current collected from LEO plasma, high temperature may cause cracks in encapsulating (Room Temperature Vulcanizing (RTV) material; radiative heating of a coupon in vacuum chamber becomes practically impossible above 1500 degrees Centigrade; conductivities of glass and adhesive go up with temperature that decrease array efficiency; and mechanical stresses grow up to critical magnitudes. A few test arrangements and respective results are presented in current paper. Coupons were tested against arcing in simulated LEO and GEO environments under elevated temperatures up to 2000 degrees Centigrade. The dependence of leakage current on temperature was measured, and electrostatic cleanness was verified for coupons with antireflection (AR) coating over the indium tin oxide (ITO) layer.

differential charging↗
NASA NTRS2018

Impact of Powder Variability on the Microstructure and Mechanical Behavior of Selective Laser Melted Alloy 718

Powder-bed additive manufacturing processes use fine powders to build parts layer-by-layer. Alloy 718 powder feedstocks for selective laser melting (SLM) additive manufacturing are produced commercially by both gas and rotary atomization and are available typically in the 10-45 or 15-45 microns size ranges. A comprehensive investigation was conducted to understand the impact of powder variability on the microstructure and mechanical behavior of SLM 718 heat treated to Aerospace Material Specification (AMS) 5664. This study included sixteen virgin powders and three once-recycled powders within the 10-45 and 15-45 microns size ranges that were obtained from seven direct source suppliers and one reseller. Although alike as highly regular spheroids, these powders showed distinct differences in composition (especially Al, C and N contents), particle size distributions, and powder features such as degree of agglomeration, fusion and surface roughness. Compositional differences expectedly had the strongest impact on microstructure. High N and C contents formed TiN-nitrides and/or (Nb,Ti,Mo)-C carbides on the grain boundaries, prevented recrystallization during heat treatment, and resulted in retained (001)-scalloped shaped grains that ranged from 19 to 41 microns in average size. In the absence of this particle pinning, the average grain size of the heat treated SLM 718 ranged from 51 microns to 90 microns. Room temperature tensile and high cycle fatigue (HCF) testing compared as-fabricated (AF) and low stress ground (LSG) surface conditions. Tensile testing revealed consistent behavior between the two surface conditions and amongst the powder lots. The finer grained SLM 718 builds displayed the lowest tensile properties. A SLM 718 build fabricated from a powder with eight times lower C content showed statistically better tensile properties presumably due to enhanced coarsening of (delta)-Ni3Nb precipitates. The specimens from once-recycled powders had slightly higher tensile strengths and slightly higher ductility compared to their virgin equivalents; once-recycling also did not substantially degrade the mean HCF life. The LSG fatigue lives agreed with conventionally manufactured 718 data, while AF lives exhibited a knock-down due to surface roughness. The fatigue lives of AF specimens were statistically equivalent across powder lots except for one and failures typically initiated at stress concentrators associated with SLM surface asperities. Fatigue testing of low stress ground specimens result in both transgranular and within facet crack initiations. More than half of the cracks initiated from these facets for the machined condition; however, these facets appeared to be within grains that were larger-than-average in size. A nitrogen-atomized powder with fine prior particles of TiN-nitrides and M(Ti,Nb,Mo)C carbides from atomization on powder surfaces resulted in the best fatigue performance with segregation of these particles to the SLM 718 grain boundaries leading to higher resistance to early-stage crack propagation. Typically the fine-grained builds with minor phases along the grain boundaries did not perform well in fatigue, whereas a larger-grain build with lower carbon content and coarser delta-Ni3Nb precipitates showed the next best HCF response. Further details of the build microstructure and its impact on tensile and fatigue behavior was considered.

laser deposition↗
NASA NTRS2022

Ab initio Screening of Refractory Nitrides and Carbides for High Temperature Hydrogen Permeation Barriers

Density functional theory was used to screen eleven refractory materials – two pure metals, six nitrides, and three carbides–as high-temperature hydrogen permeation barriers to prevent hydrogen embrittlement. Activation energies were calculated for atomic hydrogen (H) diffusion into the first subsurface layer from the lowest energy surface of the high-temperature phase of each candidate material. The candidate barrier materials with the highest activation energies are h-BN, c-BN, HfN, and ZrN with predicted barriers of 3.25 eV, 3.23 eV, 3.14 eV, and 2.76 eV, respectively. Strain energies, Bader charges, and density of states were calculated for the diffusing H at the relaxed initial state and the transition state to provide insight into contributing factors to high energy barriers. The diffusing H atom in materials with the highest predicted barriers are protic. In addition, interstitial H atoms induce mid-gap states in the density of states of both BN polymorphs. The nitrogen retention of each nitride material at high temperatures was predicted using nitrogen vacancy formation energies with respect to gaseous nitrogen. Experimental evaluation of nitrogen retention in h-BN, ZrN, and TiN confirmed their resistance to nitrogen loss at 1773 K. However, of these nitrides, TiN is predicted to be the least stable. This work identifies multiple promising materials that are predicted to be effective hydrogen barriers at high temperatures and that are stable at temperatures above 2700 K, with BN predicted to perform best.

Density Functional Theory (DFT)↗
DOE OSTI2020

Photonic near infrared heater

A multilayer photonic stack comprising a lower plurality of alternating layers comprising at least A and B and an upper plurality of alternating layers comprising at least C and D, layer A comprises at least one of Al, Au, W, Ag, Ni, Ti, Pt, and Cr, layer B comprises at least one of Al2O3, AlN, MgO, SiO2, TiO2, Si3N4, MgF2, Ta2O5, SiC, Si, Ge, and Indium Tin Oxide (ITO), and layers C and D comprise at least one of Al2O3, AlN, MgO, SiO2, TiO2, Si3N4, MgF2, Ta2O5, SiC, Si, Ge, and Indium Tin Oxide (ITO).

Prasher, Ravi Shankar↗
DOE OSTI2023

Polyoxometalate derivatized metal oxide electrodes

A porous transparent electrode is formed where a film comprising of semiconducting nanoparticles is decorated with polyoxometalates (POMs) bonded to their surfaces. The semiconducting nanoparticles are transparent metal oxide. The semiconducting nanoparticles include tin-doped indium oxide (ITO), fluorine-doped tin oxide (FTO), or titanium dioxide (TiO 2 ). In an embodiment, the POM is [SiW 12 O 40 ]L 4− ; [α-P 2 W 18 O 62 ] 6− ; or [α 2 -P 2 W 17 O 61 ] 10− . The semiconducting nanoparticles bond to the POM through a combination of electrostatic interactions and hydrogen bonds. The porous transparent electrode can be placed in a protonated form or ion-paired with alkali metal cations or tetraalkylammonium cations.

Dares, Christopher J.↗
DOE OSTI2026

Microstructural Characterization of Nb$_3$Sn Thin Films Using FIB Tomography

The accelerating gradient of N b3Sn superconducting radiofrequency (SRF) cavities is currently limited, and the underlying cause remains an open question in the field. One leading hypothesis attributes this limitation to the presence of tin-deficient regions within the N b3Sn coating, which can suppress the superheating field. Due to the relatively large coherence length of N b3Sn, defects near the surface may significantly interact with the RF field. However, these subsurface defects have proven difficult to characterize. This research aims to investigate the structure and distribution of subsurface Sn deficient regions to better understand their influence on cavity performance. We employ focused ion beam (FIB) tomography to analyze the subsurface microstructure of N b3Sn thin films. This technique enables threedimensional reconstruction of both the tin distribution and the grain structure within the film. By correlating Sn content with grain structure, we find that Sn deficient regions are more prevalent that previously thought. However, the Sn deficient regions are consistently located below the surface of the film where RF fields are strongly attenuated by supercurrent screening and are likely not a limiting factor for cavity performance

Viklund, Eric [Fermilab]↗
DOE OSTI2025

Status Report on the Development of Cladding Inner-wall and Outer-wall Coatings

Advanced cladding is critical for nuclear reactors with enhanced performance in radiation tolerance, neutron transparency and reactor safety. Using advanced cladding will ensure the adequate thermal conductivity and mechanical stability of the cladding base material, corrosion resistance and high-temperature coolant compatibility of the cladding surface, and chemical stability in the cladding inner wall against fuel cladding chemical interaction (FCCI). An innovative cladding with a three-layer structure (i.e., a modified outer surface, a robust clad base material, and a modified inner wall) promises to meet all these requirements. In this status report, the initial efforts on the development of cladding inner-wall and outer-wall coatings are summarized. The activities covered in this report are (1) High-resolution TEM studies of TiN/HT-9 interface atomic structure and chemistry after ion irradiation, (2) High-resolution TEM studies of TiN/14YWT ODS interface atomic structure after thermal cycling, (3) Inner-wall TiN coating for an experimental 14YWT ODS cladding, and (4) Corrosion test of TiN coated Ziracloy-4 bar samples.

36 - MATERIALS SCIENCE↗
DOE OSTI2021

Direct Deposition of Nonaqueous SnO 2 Dispersion by Blade Coating on Perovskites for the Scalable Fabrication of p–i–n Perovskite Solar Cells

Tin(IV) oxide materials have been extensively used as electron transport materials in n–i–p perovskite solar cells (PSCs) due to their superior optoelectronic properties, low-temperature processability, and high chemical stability. However, solvent incompatibility and processing temperature have limited the direct deposition of fully solution-processed SnO 2 in p–i–n devices. In this study, we overcome this limitation by the functionalization of SnO 2 nanoparticles with acetate through ligand exchange, allowing their dispersion in anhydrous ethanol. The SnO 2 dispersion was deposited on the perovskite absorber by blade coating without damaging the underlying perovskite layer, as determined by X-ray diffraction and scanning electron microscopy. Photoluminescence spectroscopy confirmed effective electron extraction. The champion device shows 14.1% initial power conversion efficiency (PCE) which is unprecedented for a p–i–n device employing solution-phase SnO 2 . Finally, PSCs stored for 40 days in a nitrogen flow box retained an average of 95.8% of the initial PCE.

14 SOLAR ENERGY↗