Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Scanning electron microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Strength, stiffness, and microstructure of Cu(In,Ga)Se{sub 2} thin films deposited via sputtering and co-evaporation

This work examines Cu(In,Ga)Se{sub 2} thin films fabricated by (1) selenization of pre-sputtered Cu-In-Ga and (2) co-evaporation of each constituent. The efficiency disparity between films deposited via these two methods is linked to differences in morphology and microstructure. Atomic force microscopy and scanning electron microscopy show that selenized films have rougher surfaces and poor adhesion to molybdenum back contact. Transmission electron microscopy and electron energy loss spectroscopy revealed multiple voids near the Mo layer in selenized films and a depletion of Na and Se around the voids. Residual stresses in co-evaporated films were found to be ∼1.23 GPa using wafer curvature measurements. Uniaxial compression experiments on 500 nm-diameter nanopillars carved out from co-evaporated films revealed the elastic modulus of 70.4 ± 6.5 GPa. Hertzian contact model applied to nanoindentation data on selenized films revealed the indentation modulus of 68.9 ± 12.4 GPa, which is in agreement with previous reports. This equivalence of the elastic moduli suggests that microstructural differences manifest themselves after the yield point. Typical plastic behavior with two distinct failure modes is observed in the extracted stress-strain results, with the yield strength of 640.9 ± 13.7 MPa for pillars that failed by shearing and 1100.8 ± 77.8 MPa for pillars that failed by shattering.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Multiphase Microstructure in a Metastability-Assisted Medium Carbon Alloy Steel

A medium carbon alloy steel is processed by austenizing at 900 °C for 30 min, then rapid quenching into a patented quenching liquid and holding at 170 °C for 5 min, finally isothermally holding at 250 °C for different times. The morphology and mechanical properties are performed by using optical microscopy and scanning electron microscopy. A multiphase microstructure characterized by a mixture of lenticular prior martensite (PM), fine needle bainitic ferrite and filmy retained austenite (RA) is obtained. It is found that the PM formed firstly upon quenching can accelerate the subsequent bainitic transformation and promote refinement of multiphase colonies. The results show that an optimum mechanical property of a 4000.9 MPa bending strength and a 2030 MPa tensile strength is achieved at 250 °C for 120 min, which is attributed to the multiphase microstructural characteristics and a high product of the volume fraction of RA and the carbon content of austenite.

36 MATERIALS SCIENCE↗

Structure of Ti-6Al-4V nanostructured titanium alloy joint obtained by resistance spot welding

The structure of weld joints of the titanium alloy Ti-6Al-4V in the initial ultrafine-grained state, obtained by resistance spot welding, is studied using the optical and scanning electron microscopy method and the X-ray structure analysis. The carried out studies show the relationship of the metal structure in the weld zone with main joint zones. The structure in the core zone and the heat affected zone is represented by finely dispersed grains of needle-shaped martensite, differently oriented in these zones. The change in the microhardness in the longitudinal section of the weld joint clearly correlates with structural changes during welding.

36 MATERIALS SCIENCE↗

Pulsed laser powder bed fusion additive manufacturing of A356

Highlights: • Dense A356 specimens (98 ± 0.4%) were fabricated using a customized P-LPBF system. • Microstructure and grain morphology were examined using LOM, SEM, and EBSD. • Solidification front velocities (R) were evaluated through the KGT model. • A columnar grain structure was observed and predicted by the Hunt's criterion. - Abstract: A356 (Al7SiMg) specimens were fabricated through pulsed laser powder bed fusion (P-LPBF) additive manufacturing. Microstructural examinations and analyses were carried out through the usage of light optical microscopy (LOM), scanning electron microscopy (SEM), and electron backscatter diffraction (EBSD). The results revealed a fine cellular microstructure with the intercellular network consisting of Al cells and defined by a network of Si arms. The Al cells at the center of the melt pools and within the melt pool boundary bands were measured to be 423 ± 49 nm and 664 ± 76 nm, respectively. The presence of a fine columnar grain structure and epitaxial growth on partially melted grains was observed and explained by the KGT model and Hunt's criterion.

36 MATERIALS SCIENCE↗

Biodegradation of Yerba Mate Waste Based Fertilizer Capsules. Effect of Temperature

Yerba mate waste based urea fertilizer capsules were obtained and characterized. Yerba mate powder (YMP) content in these encapsulation systems ranged from 52 to 82% for the different formulations. The aim of the study was to evaluate the effect of yerba mate powder:calcium alginate ratio and the assay temperature on capsule degradation and urea release rate in soil. Degradation evolution was monitored by microbiological tests, environmental scanning electronic microscopy, differential scanning calorimetry and Fourier transform infrared spectrometry. Encapsulation efficiency increased with YMP content. The green fertilizing systems generated did not inhibit microorganism development in soil. Degradation was slower for capsules with higher YMP content. Capsules with high YMP content released lower amounts of urea. Both degradation and release rates increased with assay temperature. The recycling of yerba mate powder as a green composite material originated a new fertilizer system.

36 MATERIALS SCIENCE↗

Controllable synthesis and optical properties of NdOHCO{sub 3} dodecahedral microcrystals

NdOHCO{sub 3} dodecahedral microcrystals with an orthorhombic structure have been successfully synthesized by the hydrothermal method used urea as the precipitator. Experimental parameters, such as the reaction temperature, the reaction time, and the molar ratio of the starting reagents were examined. The as-synthesized products were characterized by powder X-ray diffraction, transmission electron microscopy, field-emission scanning electron microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and photoluminescence. The possible growth process of NdOHCO{sub 3} dodecahedral microcrystals was discussed.

36 MATERIALS SCIENCE↗

Effects of Vanadium on Modification of Iron-Rich Intermetallics and Mechanical Properties in A356 Cast Alloys with 1.5 wt.% Fe

Formation of Fe-rich intermetallics and mechanical properties of vanadium-modified A356 cast alloys with 1.5 wt.% Fe were investigated using image analysis, scanning electron microscopy, differential scanning calorimetry, and a tensile test. The results showed that V content has no apparent influence on α-Al grain size in A356 alloys with high Fe content. Also, 0.8 wt.% V is beneficial for improving mechanical properties in A356 cast alloys with high Fe content. Specifically, these results can be attributed to the formation of Chinese script or block α-Fe phases, refined needle-like β-Fe (Al{sub 5}FeSi), and decreased porosities. An excessive amount of V deteriorates mechanical properties of alloys because it leads to VSi{sub 2} formation, large sized iron-rich intermetallics, and increased porosities.

36 MATERIALS SCIENCE↗

A study of thermal properties of sodium titanate nanotubes synthesized by microwave-assisted hydrothermal method

Highlights: • The microwave-assisted hydrothermal route was used for titanate nanotubes synthesis. • Conversion to single-phase nanotube morphology completes after 8 h reaction time. • The nanotube morphology is stable up to 600 °C, as determined by in-situ XRD and SEM. • Sodium ions migrate to the surface due to thermal motion and structure condensation. - Abstract: Sodium titanate nanotubes (NaTiNTs) were synthesized by microwave-assisted hydrothermal treatment of commercial TiO{sub 2}, at constant temperature (135 °C) and different irradiation times (15 min, 1, 4, 8 and 16 h). The products were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, differential scanning calorimetry and specific surface area measurements. The irradiation time turned out to be the key parameter for morphological control of the material. Nanotubes were observed already after 15 min of microwave irradiation. The analyses of the products irradiated for 8 and 16 h confirm the complete transformation of the starting TiO{sub 2} powder to NaTiNTs. The nanotubes are open ended with multi-wall structures, with the average outer diameter of 8 nm and specific surface area up to 210 m{sup 2}/g. The morphology, surface area and crystal structure of the sodium titanate nanotubes synthesized by microwave-assisted hydrothermal method were similar to those obtained by conventional hydrothermal method.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

FeCo Nanorods Preparation Using New Chemical Synthesis

The as-prepared and annealed iron/cobalt (FeCo) magnetic nanoparticles (NPs) were obtained using a simple method by iron chloride hexahydrate (FeCl{sub 3}.6H{sub 2}O) and cobalt chloride hexahydrate (CoCl{sub 3}.6H{sub 2}O) as precursors and sodium borohydride (NaBH{sub 4}) agent. The samples were characterized by high-resolution transmission electron microscopy (HRTEM), field effect scanning electron microscopy (FESEM), x-ray diffraction (XRD), electron-dispersive spectroscopy (EDS), and Fourier transform infrared spectroscopy (FTIR). The XRD patterns of FeCo samples showed the body center cubic (bcc) structure with a lattice constant of 2.70 Å. The SEM images showed that the particle size of the as-prepared sample was around 15 nm and the annealed sample was around 35 nm in diameter at 500 {sup ∘}C. It was found that by increasing annealing temperature, the size of the FeCo NPs increased to 60 nm at 1100 {sup ∘}C. TEM studies showed the rod-like particles for annealed sample. The sharp peaks in FTIR spectrum determined the element of FeCo NPs. EDS shows peaks of iron and cobalt with impurities in prepared samples. The result of magnetic measurements showed a good coercive field and saturation magnetization around 1158 Oe and 22 emu g{sup − 1}, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Characterization of high-temperature mechanical properties of plasma-cladded coatings with thermo-mechanical coupling

High temperature mechanical properties was detected here to study the failure and strengthening mechanism of the coating-substrate (cobalt-based coatings were fabricated on FV520B substrate) integral structure with thermo-mechanical coupling effects. Microstructure, phase composition, element distribution of the coatings was characterized by optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscope (TEM), electron back scattering diffraction (EBSD), X-ray diffraction (XRD), electron probe microanalysis (EPMA) and energy dispersive X-ray analysis (EDS). Results elucidate that fracture occurs in the coating for Co50 coating-substrate structure from 300 °C to 700 °C, but failure position transfer to substrate from coating at elevated temperatures with the addition of niobium and cerium oxide. Throughout, there is no crack originated from the interface. Fracture mechanism: the dislocation pile-up causes great stress concentration in the grain boundary, which results in the nucleation of the crack, and then the crack extends along the hard brittle Fe-Cr phase until the material fails. HRTEM shows the high density dislocation and the severe lattice distortion was formed during tensile deformation. On the macro level, the fracture tends to occur in the coarse dendrites region.

36 MATERIALS SCIENCE↗

Structural, photoconductivity, and dielectric studies of polythiophene-tin oxide nanocomposites

Highlights: • Synthesis of polythiophene-tin oxide nanocomposites confirmed by FTIR and EDAX. • SEM shows SnO{sub 2} nanoparticles embedded within polythiophene matrix. • Stability and isoelectric point suggest nanoparticle–matrix interaction. • High dielectric constant due to high Maxwell–Wagner interfacial polarization. - Abstract: Polythiophene-tinoxide (PT-SnO{sub 2}) nanocomposites were prepared by in situ chemical oxidative polymerization, in the presence of various concentrations of SnO{sub 2} nanoparticles. Samples were characterized by X-ray diffraction, Fourier-transform infrared spectroscopy, thermogravimetric analysis, X-ray photoelectron spectroscopy and Zeta potential measurements. Morphologies and elemental compositions were investigated by transmission electron microscopy, field-emission scanning electron microscopy and energy-dispersive X-ray spectroscopy. The photoconductivity of the nanocomposites was studied by field-dependent dark and photo conductivity measurements. Their dielectric properties were investigated using dielectric spectroscopy, in the frequency range of 1kHz–1 MHz. The results indicated that the SnO{sub 2} nanoparticles in the PT-SnO{sub 2} nanocomposite were responsible for its enhanced dielectric performance.

36 MATERIALS SCIENCE↗

Interfacial characterization of SLM parts in multi-material processing: Metallurgical diffusion between 316L stainless steel and C18400 copper alloy

Multi-material processing in selective laser melting using a novel approach, by the separation of two different materials within a single dispensing coating system was investigated. 316L stainless steel and UNS C18400 Cu alloy multi-material samples were produced using selective laser melting and their interfacial characteristics were analyzed using focused ion beam, scanning electron microscopy, energy dispersive spectroscopy and electron back scattered diffraction techniques. A substantial amount of Fe and Cu element diffusion was observed at the bond interface suggesting good metallurgical bonding. Quantitative evidence of good bonding at the interface was also obtained from the tensile tests where the fracture was initiated at the copper region. Nevertheless, the tensile strength of steel/Cu SLM parts was evaluated to be 310 ± 18 MPa and the variation in microhardness values was found to be gradual along the bonding interface from the steel region (256 ± 7 HV{sub 0.1}) to the copper region (72 ± 3 HV{sub 0.1}). - Highlights: • Multi-material processing was successfully implemented and demonstrated in SLM. • Bi-metallic laminates of steel/Cu were successfully produced with the SLM process. • A substantial amount of Fe and Cu diffusion was observed at the bond interface. • Good metallurgical bonding was obtained at the interface of the steel/Cu laminates. • Highly refined microstructure was obtained due to rapid solidification in SLM.

36 MATERIALS SCIENCE↗

Evaluation of the microstructure and mechanical properties of WC particle reinforced aluminum matrix composites fabricated by friction stir processing

Highlights: • FSP was used for the preparation of aluminum matrix composites reinforced with WC particle. • WC particles were uniformly distributed in the composite. • WC particles refined the grains of aluminum matrix. • WC particles enhanced the hardness and tensile strength, but decreased the ductility. - Abstract: Tungsten carbide (WC) is an attractive reinforcing material for aluminum and its alloys. However, it is technically challenging to fabricate WC particle reinforced aluminum matrix composites (AMCs) with homogeneous distribution of WC particles by liquid state processing techniques because of large density gradient. The present work aim to produce WC particle reinforced aluminum matrix composites (AMCs) through friction stir processing (FSP) and analyze the effect of its volume fraction on the microstructural features and the mechanical behavior of the developed AMCs. Microstructural evaluation was conducted on the cross-sections of the samples by optical microscopy (OM), scanning electron microscopy (SEM) and electron backscattered diffraction (EBSD). Microhardness testing was conducted across the cross-sections of FSPed samples to obtain hardness profiles and tensile test was conducted on as-received Al and FSPed samples. The fabricated AMCs exhibited the homogeneous distribution of WC particle with no obvious particle clustering in the stir zone, irrespective of position and WC particle volume fraction. Excellent WC/Al interfacial bonding was obtained in all FSPed AMCs with obviously refined grains. The average size of WC particles after FSP was slightly reduced with the increased volume fraction. It was also found that increasing the volume fraction of WC particles favored the grain refinement, improved the hardness and strength, but decreased the ductility. This improvement in the hardness and strength was attributed to the grain refinement strengthening and homogeneous distribution of WC particles. The decreased ductility resulted from the introduction of more WC particles. Increasing the volume fraction of WC particles caused the nature of fracture to move towards brittle nature.

36 MATERIALS SCIENCE↗

Metallography and microstructure interpretation of some archaeological tin bronze vessels from Iran

Archaeological excavations in western Iran have recently revealed a significant Luristan Bronzes collection from Sangtarashan archaeological site. The site and its bronze collection are dated to Iron Age II/III of western Iran (10th–7th century BC) according to archaeological research. Alloy composition, microstructure and manufacturing technique of some sheet metal vessels are determined to reveal metallurgical processes in western Iran in the first millennium BC. Experimental analyses were carried out using Scanning Electron Microscopy–Energy Dispersive X-ray Spectroscopy and Optical Microscopy/Metallography methods. The results allowed reconstructing the manufacturing process of bronze vessels in Luristan. It proved that the samples have been manufactured with a binary copper–tin alloy with a variable tin content that may relates to the application of an uncontrolled procedure to make bronze alloy (e.g. co-smelting or cementation). The presence of elongated copper sulphide inclusions showed probable use of copper sulphide ores for metal production and smelting. Based on metallographic studies, a cycle of cold working and annealing was used to shape the bronze vessels. - Highlights: • Sangtarashan vessels are made by variable Cu-Sn alloys with some impurities. • Various compositions occurred due to applying uncontrolled smelting methods. • The microstructure represents thermo-mechanical process to shape bronze vessels. • In one case, the annealing didn’t remove the eutectoid remaining from casting. • The characteristics of the bronzes are similar to other Iron Age Luristan Bronzes.

36 MATERIALS SCIENCE↗

Effect of gadolinium addition on microstructural evolution and solidification characteristics of Al-15%Mg2Si in-situ composite

Highlights: • The Al{sub 3}Gd is the heterogeneous nucleation of primary Mg{sub 2}Si in Al-15%Mg{sub 2}Si composite. • Addition of Gd to Al-15%Mg{sub 2}Si resulted in the formation of Al{sub 2}Si{sub 2}Gd and AlSiGd intermetallic compounds. • Absorption of Gd atoms preferentially on {100} facets of Mg{sub 2}Si crystals changed its growth manners. • Primary Mg{sub 2}Si transformed from coarse-dendritic to perfect truncated octahedral shape after treating with 1.0 wt% Gd. • Gd addition increased the nucleation and growth temperatures of primary Mg{sub 2}Si. - Abstract: The current study investigated the effects of gadolinium (Gd) addition (0, 0.3, 0.5, 1.0, and 2.0 wt%) on microstructural development and solidification characteristics of hypereutectic Al-15%Mg{sub 2}Si in-situ composite. Microstructural examinations were carried out via optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), and electron backscattered diffraction (EBSD). The results showed that an addition of 1.0 wt% Gd, changed the morphology of primary Mg{sub 2}Si from coarse dendritic to fine truncated octahedral shape. Furthermore, the average size of primary Mg{sub 2}Si particles decreased from 40 μm to 20 μm and density increased from 495 to 1167 particles/mm{sup 2}. Besides that, cooling curve thermal analysis (CCTA) technique revealed that Gd addition increased nucleation and growth temperatures of primary Mg{sub 2}Si phase. It is proposed that modification and refinement mechanism of Gd addition are mainly attributed to formation of tiny Al{sub 3}Gd particles as the heterogeneous nucleation substrates for primary Mg{sub 2}Si, which results in a refined distribution of these particles and poisoning effect by adsorbing Gd atoms, preferentially on {100} facets of Mg{sub 2}Si crystals. Moreover, it is believed that formation of Gd intermetallic compounds is responsible for refinement of primary Mg{sub 2}Si particles.

36 MATERIALS SCIENCE↗

Self-assembly of multiferroic core-shell particulate nanocomposites through DNA-DNA hybridization and magnetic field directed assembly of superstructures

Multiferroic composites of ferromagnetic and ferroelectric phases are of importance for studies on mechanical strain mediated coupling between the magnetic and electric subsystems. This work is on DNA-assisted self-assembly of superstructures of such composites with nanometer periodicity. The synthesis involved oligomeric DNA-functionalized ferroelectric and ferromagnetic nanoparticles, 600 nm BaTiO{sub 3} (BTO) and 200 nm NiFe{sub 2}O{sub 4} (NFO), respectively. Mixing BTO and NFO particles, possessing complementary DNA sequences, resulted in the formation of ordered core-shell heteronanocomposites held together by DNA hybridization. The composites were imaged by scanning electron microscopy and scanning microwave microscopy. The presence of heteroassemblies along with core-shell architecture is clearly observed. The reversible nature of the DNA hybridization allows for restructuring the composites into mm-long linear chains and 2D-arrays in the presence of a static magnetic field and ring-like structures in a rotating-magnetic field. Strong magneto-electric (ME) coupling in as-assembled composites is evident from static magnetic field H induced polarization and low-frequency magnetoelectric voltage coefficient measurements. Upon annealing the nanocomposites at high temperatures, evidence for the formation of bulk composites with excellent cross-coupling between the electric and magnetic subsystems is obtained by H-induced polarization and low-frequency ME voltage coefficient. The ME coupling strength in the self-assembled composites is measured to be much stronger than in bulk composites with randomly distributed NFO and BTO prepared by direct mixing and sintering.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Synthesis and characterization of low softening point high Bi{sub 2}O{sub 3} glasses in the K{sub 2}O-B{sub 2}O{sub 3}-Bi{sub 2}O{sub 3} system

Synthesis of a new series of lead free low softening point (< 470 deg. C) high Bi{sub 2}O{sub 3} (40-90 mol%) glasses in the K{sub 2}O-B{sub 2}O{sub 3}-Bi{sub 2}O{sub 3} system by the melt-quench technique has been demonstrated here. Their structural, optical, thermal, electrical and other physical properties have been evaluated by X-ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscopy (FESEM), FT-infrared reflection (FTIRR) spectroscopy, UV-Visible spectroscopy, dilatometer, LCR meter, etc. techniques. The glass softening point, glass transition temperature and glass deformation temperature are found to vary in the ranges 410-465 deg. C, 354-409 deg. C and 376-427 deg. C respectively which are found to correlate well with the boron anomaly phenomenon (as revealed by FTIRRS) with gradual addition of Bi{sub 2}O{sub 3} in the glass matrix. The coefficient of thermal expansion shows a decreasing trend from 153 down to 109 x 10{sup -7} K{sup -1} whereas the dielectric constant increases from 21 to 34 with the increase in Bi{sub 2}O{sub 3} content. The theoretical optical basicity is found to increase from 0.93 to 1.15 while the optical band gap decreases from 2.86 down to 2.30 eV with the addition of Bi{sub 2}O{sub 3}. The formation of metallic bismuth in these glasses during melting in air has been confirmed by the XRD, TEM, selected area electron diffraction (SAED) and high resolution TEM (HRTEM) analyses. The formation of a Bi{sub 2}O{sub 3} rich secondary phase in the glasses and their particle size distribution have been examined by the FESEM photomicrograph analysis. - Research Highlights: {yields} Synthesis of low softening point (< 470 deg. C) high Bi{sub 2}O{sub 3} content (40-90 mol%) glasses. {yields} Study of boron anomaly phenomenon with gradual addition of Bi{sub 2}O{sub 3} in the glass. {yields} Co-efficient of thermal expansion decreases from 153 to 109 x 10{sup -7} K{sup -1}. {yields} Dielectric constant increases from 21 to 34 with increase in Bi{sub 2}O{sub 3} content. {yields} Formation of metallic bismuth in the glass confirmed by the XRD and TEM analyses.

36 MATERIALS SCIENCE↗