SEARCH · Engineering Papers

Results for “STRENGTH CALCULATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

All sources NASA NTRS DOE OSTI

NASA NTRS1986

Combined bearing and bypass loading on a graphite/epoxy laminate

A combined experimental and analytical study was conducted to determine the behavior of a graphite/epoxy laminate subjected to combined bearing and bypass loading. Single-fastener quasi-isotropic specimens were loaded at various bearing-bypass ratios until damage was produced at the fastener hole. Damage-onset strengths and damage modes were then analyzed using local hole-boundary stresses calculated by a finite-element analysis. The tension data showed the expected linear interaction for combined bearing and bypass loading with damage developing in the net-section tension mode. However, the compression bearing-bypass strengths showed an unexpected interaction involving the bearing mode. Compressive bypass loads reduced the bearing strength by decreasing the bolt-hole contact arc and thus increasing the severity of the bearing loads. The bearing stresses at the hole boundary were not accurately estimated by superposition of the stress components for separate bearing and bypass loading. However, superposition produced reasonably accurate estimates for tangential stresses especially near the specimen net-section.

Crews, J. H., Jr.↗

NASA NTRS1986

Combined bearing and bypass loading on a graphite/epoxy laminate

Crews, J. H., Jr.↗

NASA NTRS1987

Effect of atmospheric turbulence on the bit error probability of a space to ground near infrared laser communications link using binary pulse position modulation and an avalanche photodiode detector

The effect of atmospheric turbulence on the bit error rate of a space-to-ground near infrared laser communications link is investigated, for a link using binary pulse position modulation and an avalanche photodiode detector. Formulas are presented for the mean and variance of the bit error rate as a function of signal strength. Because these formulas require numerical integration, they are of limited practical use. Approximate formulas are derived which are easy to compute and sufficiently accurate for system feasibility studies, as shown by numerical comparison with the exact formulas. A very simple formula is derived for the bit error rate as a function of signal strength, which requires only the evaluation of an error function. It is shown by numerical calculations that, for realistic values of the system parameters, the increase in the bit error rate due to turbulence does not exceed about thirty percent for signal strengths of four hundred photons per bit or less. The increase in signal strength required to maintain an error rate of one in 10 million is about one or two tenths of a db.

Safren, H. G.↗

NASA NTRS1978

Bar-driven spiral waves in disk galaxies

The response of rotating disks of gas to barlike perturbations in galactic gravitational fields is investigated. In particular, two-dimensional time-dependent numerical hydrodynamical calculations have been performed in order to determine the steady-state response of disks of gas to rotating barlike perturbations. Two types of barlike perturbations are considered: oval distortions in the axisymmetric gravitational field of the disk, and heterogeneous prolate spheroids. The calculations reveal that in the absence of gaseous self-gravity, a viscous differentially rotating disk of gas responds to a rotating barlike perturbation by forming a central gas bar with two trailing spiral waves. The local phase of the gas response is primarily a function of the number and spacing of the principal resonances in the disk. This result may be understood in terms of particle orbit theory. The gas response to barlike perturbations also depends on the relative strength and the effective axial ratio of the bar. In these calculations strong narrow bars produce offset shocks in the central gas bar. These shocks correspond in position to the long narrow dust lanes observed in many barred spiral galaxies.

Huntley, J. M.↗

DOE OSTI2020

Fullerene Negative Ions: Formation and Catalysis

We first explore negative-ion formation in fullerenes C 44 to C 136 through low-energy electron elastic scattering total cross sections calculations using our Regge-pole methodology. Then, the formed negative ions C 44 – to C 136 – are used to investigate the catalysis of water oxidation to peroxide and water synthesis from H 2 and O 2 . The exploited fundamental mechanism underlying negative-ion catalysis involves hydrogen bond strength-weakening/breaking in the transition state. Density Functional Theory transition state calculations found C 60 – optimal for both water and peroxide synthesis, C 100 – increases the energy barrier the most, and C 136 – the most effective catalyst in both water synthesis and oxidation to H 2 O 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Neutron-hole strength in N = 81 nuclei

A systematic study of neutron-hole strength in the N = 81 nuclei 137 Ba, 139 Ce, 141 Nd, and 143 Sm is reported. The single-neutron removal reactions (p,d) and ( 3 He,α) were measured at energies of 23 and 34 MeV, respectively. Spectroscopic factors were extracted from measured cross sections through a distorted-wave Born approximation analysis and centroids of single-particle strength have been established. Here, the change in these centroid energies as a function of proton number have been compared to calculations of the monopole shift for the s 1/2 and h 11/2 orbitals, where the majority of the strength has been observed. Significant fragmentation of strength was observed for the d and g 7/2 orbitals, particularly for the latter orbital which is deeply bound, with summed strengths that indicate a significant amount lies outside of the measured excitation energy range.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2022

Neutral-current neutrino cross section and expected supernova signals for 40 Ar from a three-fold increase in the magnetic dipole strength

In view of the great interest in liquid argon neutrino detectors, the 40 Ar(γ,γ') 40 Ar reaction was revisited to guide a calculation of the neutral current neutrino cross section at supernova energies. Using the nuclear resonance fluorescence technique with a monoenergetic, 99% linearly polarized photon beam, in this work we report a three-fold increase in magnetic dipole strength at around 10 MeV in 40 Ar. Based on shell-model calculations, and using the experimentally identified transitions, the neutral current neutrino cross sections for low-energy reactions on 40 Ar are calculated.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRS1972

Interpolation constants for calculation of transmittance and rate of dissociation of molecular oxygen in the mesosphere and lower thermosphere

Values of band oscillator strengths and rotational line widths for the Schumann-Runge band system have been used to derive interpolation constants from which the transmittance and rate of dissociation of molecular oxygen can be calculated. These constants, valid for temperatures between 150 and 300 K and for column densities between 1 x 10 to the 17th power/cm sq and 7 x 10 to the 24th power/cm sq, cover the wavelength range 1750 and 2050A.

Hudson, R. D.↗

DOE OSTI2020

Primary $\gamma$-ray intensities and $\gamma$-strength functions from discrete two-step $\gamma$-ray cascades in radiative proton-capture experiments

Background: Reaction rates of radiative capture reactions can play a crucial role in the nucleosynthesis of heavy nuclei in explosive stellar environments. These reaction rates depend strongly on $\gamma$-ray decay widths in the reaction products, which are, for nonresonant capture reactions at high excitation energies, derived from the $\gamma$-ray strength function and the nuclear level density. Recently, the ratio method was applied to primary $\gamma$ rays observed from ($\textit{d, p}$) reactions and nuclear resonance fluorescence measurements to extract the dipole strength in atomic nuclei and to test the generalized Brink-Axel hypothesis. Purpose: The purpose of this work is to apply the ratio method to primary $\gamma$-ray intensities of the 63,65 Cu($\textit{p},\gamma$) reactions to extract $\gamma$-ray strength information on the nuclei 64,66 Zn. Here, the impact of spin distribution, total $\gamma$-ray decay widths, level densities, and width fluctuations on the application of the ratio method will be discussed. Additionally, by comparing the relative $\gamma$-ray strength at different excitation energies, conclusions on the validity of the generalized Brink-Axel hypothesis can be made. Method: The radiative proton capture reaction measurements have been performed at the HORUS $\gamma$-ray spectrometer of the University of Cologne at one excitation energy for each reaction. Primary $\gamma$-ray intensities have been determined by normalizing secondary $\gamma$-ray transitions in two-step cascades using their absolute branching ratio. The ratio method was applied to the measured primary $\gamma$-ray intensities as well as to previous measurements by Erlandsson et al. at different excitation energies. Results: The relative strength function curve for 64 Zn from our measurement shows no significant deviation from the previous measurement at a different excitation energy. The same is true for 66 Zn where both measurements were at almost the same excitation energy. Absolute $\gamma$-strength function values have been obtained by normalizing the relative curves to quasiparticle random phase approximation calculations because of the absence of experimental data in the respective energy region. Conclusion: The generalized Brink-Axel hypothesis, i.e., the independence of the strength function on the excitation energy, seems to hold in the studied energy region and nuclei. The method to obtain primary $\gamma$-ray intensities from two-step cascade spectra was shown to be a valuable and sensitive tool although its uncertainties are connected to the knowledge of the low-energy level scheme of the investigated nucleus. The scaling in the ratio method should be taken with care, because the relative strength is not a simple sum of $f_{E1}$ and $f_{M1}$ but a somewhat complex linear combination dependent on the excitation energy of the nucleus.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2020

(U) PRAD0697 & PRAD0698: Complex Loading of CeO₂ Powder

Cerium(IV) oxide (CeO₂) powder is shock compressed using the Precision High Energy-density Liner Implosion eXperiment (PHELIX) platform. Experimental results are compared against several modeling approaches. Compaction behavior is best captured with a P-∝ model, which calculates CeO₂ powder bulk densities within 80-99% of experimental values but overpredicts densi cation at the cylindrical target's outer radius and center by up to 20%. Preliminary calculations suggest that accuracy could be increased with the inclusion of a coupled strength model. Several common computational modeling approaches for the shock compression response of granular materials and the magnetohydrodynamic (MHD) force upon the impactor/liner in pulsed power compression experiments are investigated and analyzed for their validity. The Bi-linear Ramp, P-∝ PACXP, and P-∝ Menikoff-Kober continuum compaction models are calibrated to planar impact Hugoniot data for CeO₂ powder and used to predict the powder's shock compaction response under non-planar shock wave compression. MHD calculations of the PHELIX pulsed power driver are performed using an idealized resistor-inductor-capacitor (RLC) circuit calibrated to previous experiments. All simulations are performed using the LANL code FLAG. Two validation experiments are computationally designed using the calibrated compaction and circuit models, executed using the PHELIX platform on CeO₂ targets with initial porous densities of 3.95 and 4.03 g/cm³, measured with proton radiography, and analyzed against the model predictions. The two P-∝ models more accurately describe CeO₂ powder densi cation than the Bi-linear Ramp model. However, the two P-∝ models overpredict bulk density of the shock compressed CeO₂ powder by up to 20% when the appropriate impact velocities are applied. MHD calculations for both validation experiments underpredict liner impact velocities by 4-11% when using the idealized RLC circuit model calibrated to previous experiments. Compensating underpredictions of impact velocity and overpredictions of powder densication lead to a false accuracy in pre-shot calculations compared to experimental data. To improve correlation between simulations and experiments, the following improvements are suggested: 1. A coupled strength model for CeO₂ powder that updates strength as a function of porosity and applied stress. 2. An improved MHD circuit model that more accurately captures the PHELIX machine.

36 MATERIALS SCIENCE↗

NASA NTRS1952

A Summary of Diagonal Tension Part I : Methods of Analysis

Previously published methods for stress and strength analysis of plane and curved shear webs working in diagonal tension are presented as a unified method. The treatment is sufficiently comprehensive and detailed to make the paper self-contained. Part 1 discusses the theory and methods for calculating the stresses and shear deflections of web systems as well as the strengths of the web, the stiffeners, and the riveting. Part 2, published separately, presents the experimental evidence. (author)

Kuhn, Paul↗

NASA NTRS1947

Strength analysis of stiffened beam webs

Explore the source record for details and available documents.

STRESS CALCULATIONS↗

NASA NTRS1976

An analytical study of noise generation by subsonic flows in the presence of rigid surfaces

A general analytical method is developed for determination of the radiated noise field from highly sheared, subsonic flows in the presence of rigid surfaces. The method is specifically formulated to use measurable flow field properties as the basis input data for calculations. The governing equations of a viscous, incompressible fluid are employed to determine approximately the so-called shear noise source strength distribution in the flow. Mean rates of strain and fluctuating velocity covariances are the fundamental input data for calculations. The method is applied to the wall jet region of a circular jet impinging at 45 deg to an infinite plane surface. Velocity field measurements of Foss are used to describe the required flow properties. Comparisons of calculated results with measured surface pressures and sound pressure levels are given and discussed.

Wooley, J. P.↗

DOE OSTI2022

Electron-phonon coupling strength from ab initio frozen-phonon approach

In this work, we propose a fast method for high-throughput screening of potential superconducting materials. The method is based on calculating metallic screening of zone-center phonon modes, which provides an accurate estimate for the electron-phonon coupling strength. This method is complementary to the recently proposed Rigid Muffin Tin (RMT) method, which amounts to integrating the electronphonon coupling over the entire Brillouin zone (as opposed to the zone center), but in a relatively inferior approximation. We illustrate the use of this method by applying it to MgB 2 , where the high-temperature superconductivity is known to be driven largely by the zone-center modes, and compare it to a sister compound AlB 2 . We further illustrate the usage of this descriptor by screening a large number of binary hydrides, for which accurate first-principle calculations of electron-phonon coupling have been recently published. Together with the RMT descriptor, this method opens a way to perform initial high-throughput screening in search of conventional superconductors via machine learning or data mining.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Fatigue performance of laser powder bed fusion hydride-dehydride Ti-6Al-4V powder

We report hydride-dehydride (HDH) Ti-6Al-4V alloy with particle size distribution of 50–120 µm is laser powder bed fusion (L-PBF) processed using optimum processing parameters and a near-fully dense structure with a density of 99.9 % is achieved. Microstructural observations and phase analyses indicate formation of columnar β grains with acicular α/α' phases in as-built condition. The roughness of the as-fabricated samples is significant with an average roughness of R a = 15.71 ± 3.96 µm and a root mean square roughness of R rms = 108.4 ± 24.9 µm, however, both values are reduced to R a = 0.19 ± 0.04 µm and R rms = 4.9 ± 0.6 µm after mechanical grinding. Mechanical tests are carried out on as-fabricated specimens followed by stress relief treatment. All samples are tested to failure in fatigue, under fully-reversed tension-compression conditions of R = –1. The as-built samples failed from the surface with crack initiation mainly at micro-notches, whereas after mechanically grinding, crack initiation changed to subsurface defects such as pores. Minimizing surface roughness by mechanically grinding eliminates surface micro-notches which improves fatigue strength in the high cycle fatigue region. Fatigue notch factor calculations showed that the effect of surface roughness was significantly lower when HDH powder is used compared to standard spherical powder. X-ray diffraction analysis revealed an in-plane compressive stress, micro-strain and grain refinement on the surface of the mechanically ground samples. Fractography observations (macroscale) revealed a fully brittle fracture in the first stage of crack growth with a transition to a dominantly ductile fracture in the third stage of crack growth. On the other hand, at the micro scale, even the brittle fracture regions showed evidence of ductile fracture within the α' martensite laths.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Unraveling Anion-Specific Inhibition and Structural Modulation of Gibbsite Crystallization: Implications for Aluminum Mobility in Natural and Engineered Systems

Gibbsite (α-Al(OH) 3 , sometimes designated as γ-Al(OH) 3 ) plays a crucial role in the chemistry of aluminum in the environment and industry, yet its crystallization behavior under multianionic conditions is not well understood. Here, in this study, we investigate how six common anions─fluoride (F – ), chloride (Cl – ), bromide (Br – ), nitrate (NO 3 – ), sulfate (SO 4 2– ), and phosphate (PO 4 3– )─influence the mineralization, structure, and morphology of gibbsite at room temperature. The results show that PO 4 3– , SO 4 2– , and F – strongly inhibit gibbsite formation, stabilizing amorphous or alternative crystalline phases such as nordstrandite and cryolite. On the contrary, Cl – , Br – , and NO 3 – allow partial to complete crystallization of gibbsite without significant morphological changes. Solid-state 27 Al magic angle spinning nuclear magnetic resonance provides crucial insight into aluminum coordination environments in both crystalline and amorphous phases, distinguishing between octahedral, pentahedral, and tetrahedral Al species. The density functional theory calculations reveal a direct correlation between the Al–X bond strength and the inhibition of crystallization, following the order: PO 4 3– > SO 4 2– > F – > NO 3 – > Cl – > Br – . These findings offer molecular-scale insights into anion-specific effects on aluminum hydroxide nucleation and transformation, improving the understanding of gibbsite formation and aluminum cycling in soils, phosphate retention, contaminant immobilization, and waste treatment strategies in nuclear and industrial settings. These insights can also guide the controlled synthesis of aluminum hydroxide materials with tailored crystallinity and morphology via liquid-assisted methods.

Anions effect↗

DOE OSTI2023

Proximate spin liquid and fractionalization in the triangular antiferromagnet KYbSe 2

The Heisenberg triangular-lattice quantum spin liquid and its phase transitions to nearby magnetic orders have received much theoretical attention, but clear experimental manifestations of these states are rare. Here we demonstrate that a spin-half delafossite material, namely, KYbSe 2 , shows close proximity to the triangular-lattice Heisenberg quantum spin liquid. Using neutron scattering, we identify a diffuse continuum with a sharp lower bound within the measured spectra. Applying entanglement witnesses to the data indicates multipartite entanglement spread between its neighbours, and an analysis of its magnetic-exchange couplings reveals close proximity to the theoretical quantum spin-liquid phase. The key features of the data are reproduced by Schwinger boson theory and tensor network calculations with a substantial next-nearest-neighbour coupling. The strength of the dynamical structure factor at the Brillouin-zone K point shows a scaling collapse down to 0.3 K, indicating the existence of a second-order quantum phase transition. Finally, comparing this with previous theoretical work suggests that the proximate phase at a larger next-nearest-neighbour coupling is a gapped $\mathbb{Z}_{2}$ spin liquid, resolving a long-debated issue. Similar content being viewed by others

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2022

Can a shock-induced phonon up-pumping model relate to impact sensitivity of molecular crystals, polymorphs and cocrystals?

Impact sensitivity engineering of high-energy molecular crystals requires accurate predictive models. For this purpose, the promising multi-phonon based approach is selected, assessing a bit more its strengths and weaknesses. Presently used with high-quality phonon calculations of 22 molecular crystals, using a physics-based criterion to determine the phonon bath extent, the resulting intrinsic shock sensitivity index (SSI) is compared to the most common marker of impact sensitivity, h 50 , as determined from drop-weight impact tests. Selecting a data subset from experiments performed under very similar conditions (2.5 kg hammer with grit and 30–40 mg samples), the model can predict h 50 values for mono-molecular crystals with very good accuracy, including the ability to discriminate the polymorphs of HMX and CL20. This very good agreement validates an initial indirect up-pumping mechanism occurring under these conditions, where the doorway modes also interact with the phonon bath. However, the phonon bath criterion for mono-molecular crystals does not transfer well to cocrystals. Owing to the vibrational coupling of the co-molecules, it seems a broader phonon bath should be considered. Additionally recalling experimental uncertainty and various experimental factors affecting h 50 values for a given compounds, we recommend that the density of the sample, granularity and morphology be systematically considered and reported along with measurements, which will in turn allow for more systematic data and predictive capabilities for sensitivity models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗