Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SILICATES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Chloride diffusivity, chloride threshold, and corrosion initiation in reinforced alkali-activated mortars: Role of calcium, alkali, and silicate content

The aim of this study is to investigate systematically the chloride diffusivity and chloride threshold of a wide range of calcium-rich and fly ash-dominated alkali-activated samples in light of their compositional differences. To this end, the effects of various fly ash (FA)-to-slag ratios, of alkali concentrations and of silicate content in the activator were investigated. The electrochemical aspects of the passive samples were also assessed. Results show the prominent role of calcium in the matrix to reduce the chloride diffusivity. While higher alkali concentration increased the porosity and chloride diffusivities in general, lower modulus ratios provided considerably better performance in the FA-dominated samples. Chloride threshold values range between 0.19 (wt% binder mass) for calcium-rich mortars fabricated at low levels of alkalinities and 0.69 for FA-dominated mortars fabricated with highly alkaline activators. Half-cell potential and polarization resistance of alkali-activated samples were in general lower than their Portland cement counterparts.

36 MATERIALS SCIENCE↗

Effects of pH on the nano/micro structure of calcium silicate hydrate (C-S-H) under sulfate attack

Calcium silicate hydrate (C-S-H), the most important Portland cement hydration product, determines the mechanical properties and durability of cementitious materials. In marine environment, C-S-H often suffers from sulfate attack – one of the most common and severe degradations for concrete. pH is considered as a critical factor in determining the deterioration behavior of C-S-H during sulfate attack, of which the significance may be overlooked. This study focused on the role of pH on the deterioration of C-S-H in terms of the composition and nano/micro structure under sulfate attack. The results show that lowering pH aggravates the decalcification of C-S-H, whereas a strong alkaline condition is beneficial to increase the resistance to deterioration. An increase in the mean chain length together with the proportion of large pores (>10 nm) is observed when C-S-H is subjected to low-pH sulfate attack (pH = 10–12), resulting in a relatively loose structure. The deep analysis on defective tobermorite model reveals that calcium at the interlayer of C-S-H nanostructure is readily removed under sulfate attack, thereby improving the potential of Si-O-Si groups formation and increases the mean chain length of C-S-H.

36 MATERIALS SCIENCE↗

Effective cation exchange capacity of calcium silicate hydrates (C-S-H)

The binding of alkalis and calcium to calcium silicate hydrate (C-S-H) can be measured by cation exchange using cobalt hexamine solution with adapted pH. The effective cation exchange capacity (CEC) decreased at higher Ca/Si in C-S-H. A maximum of charge{sub exch}/Si of 0.08–0.10 was measured at Ca/Si = 0.8 decreasing to 0.01–0.02 at Ca/Si = 1.6. At high Ca/Si, only a minor fraction of Ca was present at exchangeable sites, while most of the Ca{sup 2+} present in interlayer or surface was specifically bound and thus not exchangeable. In contrast, sodium was present only at exchangeable sites in the C-S-H, more at low than at high Ca/Si. An increase of pH in the presence of 100 mmol/L NaOH increased the effective CEC of C-S-H by 5–10% indicating a limited influence of pH on the deprotonation of the silanol groups.

36 MATERIALS SCIENCE↗

Near-field infrared microscopy: A novel analytic mapping technique to nanocharacterize calcium silicate-based cement materials

Infrared imaging via scattering-type scanning near-field optical microscopy (s-SNOM) allows chemical mapping of organic and inorganic materials with nanoscale spatial resolution. However, its potential adaptation to the complex multiphase structure of Portland cement is yet to be explored. Here we demonstrate the successful implementation of s-SNOM to spatially resolve coexisting chemical phases in tricalcium silicate, Portland cement's main compound, with 20-nm resolution. We found that s-SNOM is sensitive to different anhydrous polymorphic phases, revealing nanoscale domains that are ‘invisible’ to other microscopic techniques. Furthermore, s-SNOM's ability to distinguish the unhydrated and hydrated phases signifies its great promise as an analytical tool to study the complex hydration process of cement. The key to s-SNOM's application was nano-modifying the surface roughness of the cement samples, allowing nanoscale infrared imaging without topographical artifacts. Our study opens a window for infrared spectral microscopy in cement and other porous inorganic materials.

36 MATERIALS SCIENCE↗

Atomistic thermodynamics and kinetics of dicalcium silicate dissolution

Low-temperature cement manufacturing has garnered academic and industrial attention for its low environmental footprints. However, the sluggish hydration kinetics of the resultant cement affects their early-age strength development. This motivates fundamental studies to unravel the mechanistic picture of the dissolution process and discover science-informed pathways to accelerate hydration. Standard atomistic simulations seldomly exceed a microsecond making them impractical to study slow dissolution processes. We are using rare event sampling techniques, we provide the mechanistic picture of Ca 2+ ion dissolution from a kink site on the dicalcium silicate surface. The Ca 2+ ion dissolution is comprised of two sequential stages: breaking restraints from the kink sites to form a ledge adatom and detaching from the ledge/terrace adatom sites into the solution. The first and second stages feature free energy barriers of ~63 kJ/mol and ~ 29 kJ/mol respectively, making the first stage the rate-limiting step of the entire Ca 2+ dissolution kinetics. Using the reactive flux method, the rate and equilibrium constants for each reaction step are calculated, which yield the Ca 2+ ion activity of ~1.03 × 10 -5 . The diffusion calculations indicate that the surface effects lower the self-diffusion coefficient of Ca 2+ ions at the solid-water interface.

36 MATERIALS SCIENCE↗

Ultra-high gamma irradiation of calcium silicate hydrates: Impact on mechanical properties, nanostructure, and atomic environments

The concrete biological shield in a nuclear power plant receives ~100–200 MGy gamma dosage during an 80-year design life. However, precise changes in the mechanical properties and atomic environments of C-S-H at ultrahigh irradiation dosages have not been systematically documented. Here, we report that irradiation decreases C-S-H basal spacing (~ 0.6 ± 0.1 Å for 189 MGy) and increases its Young's modulus, which is attributed to the lower basal spacing as the nano porosity potentially increased and microporosity remained unchanged. Irradiation also decreased the molecular water content and increased hydroxyl groups in C-S-H, showing that interlayer water removal reduces the basal spacing. Finally, 1 H and 29 Si NMR results indicate some disorder in the local proton CaO-H species and slight depolymerization of the silicate structure. Together, these results indicate that the C-S-H gel stiffens upon ultrahigh gamma irradiation dosage, a finding which concerns long-term nuclear power plants operations worldwide.

1H NMR↗

Spherulite Crystallization Induces Fe-Redox Redistribution in Silicic Melt

Rhyolitic obsidians from Krafla volcano, Iceland, record the interaction between mobile hydrous species liberated during crystal growth and the reduction of ferric iron in the silicate melt. We performed synchrotron {mu}-FTIR and {mu}-XANES measurements along a transect extending from a spherulite into optically distinct colorless and brown glass zones. Measurements show that the colorless glass is enriched in OH groups and depleted in ferric iron, while the brown glass shows the opposite relationship. The color shift between brown and clear glass is sharp, suggesting that the colorless glass zone was produced by a redox front that originated from the spherulite margin and moved through surrounding melt during crystallization. We conclude that the most likely reducing agent is hydrogen, produced by magnetite crystallization within the spherulite. The Krafla obsidians dramatically capture redox disequilibrium on the micoscale and highlight the importance of hydrous fluid liberation and late-stage crystallization to the redox signature of glassy lavas.

08 HYDROGEN↗

Iron K-edge X-ray absorption near-edge structure spectroscopy of aerodynamically levitated silicate melts and glasses

Here, the local structure about Fe(II) and Fe(III) in silicate melts was investigated in-situ using iron K-edge X-ray absorption near-edge structure (XANES) spectroscopy. An aerodynamic levitation and laser heating system was used to allow access to high temperatures without contamination, and was combined with a chamber and gas mixing system to allow the iron oxidation state, Fe 3+ /ΣFe, to be varied by systematic control of the atmospheric oxygen fugacity. Eleven alkali-free, mostly iron-rich and depolymerized base compositions were chosen for the experiments, including pure oxide FeO, olivines (Fe,Mg) 2 SiO 4 , pyroxenes (Fe,Mg)SiO 3 , calcic FeO-CaSiO 3 , and a calcium aluminosilicate composition, where total iron content is denoted by FeO for convenience. Melt temperatures varied between 1410 and 2160 K and oxygen fugacities between FMQ – 2.3(3) to FMQ + 9.1(3) log units (uncertainties in parentheses) relative to the fayalite-magnetite-β-quartz (FMQ) buffer.

36 MATERIALS SCIENCE↗

Pore structure development during hydration of tricalcium silicate by X-ray nano-imaging in three dimensions

We report that tricalcium silicate (C 3 S) is the most important component among the four main clinker phases of Portland cement. Pure C 3 S is widely used as a simplified model system of cement in various researches. However, the spatial structure development of cement, even pure C 3 S during hydration at the nano-scale has been rarely directly reported. In this work, X-ray nano-computed tomography (X-ray Nano-CT), a non-destructive X-ray analytical method, was used to study the hydration of a pure C 3 S sample with a water/C 3 S mass ratio of 0.5. The three-dimensional (3D) structure of the hydrating C 3 S specimen was investigated to see the internal pore structure evolution within the hardened C 3 S paste. Investigation of the 3D structural development of the C 3 S specimen at different hydration times was performed to monitor the changes of pore shapes and sizes/volumes. Lastly, it is found that volumes of the sealed pores generally grow larger, and the open pores become smaller while the volume and the external morphology of the whole hardened C 3 S paste remains almost the same during hydration.

36 MATERIALS SCIENCE↗

Evolution of the structure and chemical composition of the interface between multi-component silicate glasses and yttria-stabilized zirconia after 40,000 h exposure in air at 800 °C

The chemical and structural stability of two commercial multicomponent silicate glasses (SCN and G6) in contact with yttria-stabilized zirconia (YSZ) was investigated after exposure times of up to 40,000 h in air at 800 °C. With exposure time, interfacial layers develop at the SCN-YSZ and G6-YSZ interfaces, which were characterized in detail using both quantitative chemical analysis and atomic-resolution imaging. At the SCN-YSZ interface, a Ca-Ba-Si-O reaction phase was found to grow by diffusion control. In G6-YSZ, Raman spectroscopy and electron microscopy revealed a disorganized interfacial reaction later between G6 and YSZ, and the occurrence of cubic to tetragonal to monoclinic phase transformations in YSZ. Finally, this microstructural evolution is discussed in terms of devitrification resistance of glass and diffusion processes at interfaces.

36 MATERIALS SCIENCE↗

Tin Valence and Local Environments in Silicate Glasses as Determined From X-ray Absorption Spectroscopy

X-ray absorption spectroscopy (XAS) was used to characterize the tin (Sn) environments in four borosilicate glass nuclear waste formulations, two silicate float glasses, and three potassium aluminosilicate glasses. Sn K-edge XAS data of most glasses investigated indicate Sn4+O6 units with average Sn-O distances near 2.03 Angstroms. XAS data for a float glass fabricated under reducing conditions show a mixture of Sn4+O6 and Sn2+O4 sites. XAS data for three glasses indicate Sn-Sn distances ranging from 3.43 to 3.53 Angstroms, that suggest Sn4+O6 units linking with each other, while the 4.96 Angstroms Sn-Sn distance for one waste glass suggests clustering of unlinked Sn4+O6 units.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Hole traps in sodium silicate: First-principles calculations of the mobility edge

Here, the structure and properties of (Na 2 O) 0.30 (SiO 2 ) 0.70 sodium silicate glass are studied by combined ab-initio and classical molecular dynamics simulations to identify the sources of electronic traps in the band gap. Structures from classical molecular dynamics melt-quench simulations are taken as initial configurations for first-principles density functional theory structural relaxation, from which electronic properties are determined. An ensemble of thirty glass structures, each containing 660 atoms, is prepared in order to perform statistical analyses. The inverse participation ratio is used as a metric to characterize localized states in the band gap and determine the mobility edge. Structures with varying amounts of local disorder (traps) are compared. The most localized and highest energy trap states are due to Si atoms with 2–3 non-bridging oxygen atoms. Control of the electronic properties of amorphous insulators and semiconductors is essential for the advancement of many technologies, such as photovoltaics and scintillators, for which the present analysis is indispensable.

36 MATERIALS SCIENCE↗

Physical properties of an alumino-silicate waste form for cesium and strontium.

Nuclear fuel reprocessing will be required to sustain nuclear power as a baseload energy supplier for the world. New reprocessing schemes offer an opportunity to develop a better strategy for recycling elements in the fuel and preparing stable waste forms. Advanced strategies could create a waste stream of cesium, strontium, rubidium, and barium. Some physical properties of a waste form containing these elements sintered into bentonite clay were evaluated. We prepared samples loaded to 27% by mass to a density of approximately 3 g/cm{sup 3}. Sintering temperatures of up to 1000 C did not result in volatility of cesium. Instead, the crystallinity noticeably increased in the waste form as temperatures increased from 600 to 1000 C. Assemblages of silicates were formed. Significant water evolved at approximately 600 C but no other gases were generated at higher temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Marginal Gaps between 2 Calcium Silicate and Glass Ionomer Cements and Apical Root Dentin

Introduction: The outcome of periapical surgery has been directly improved with the introduction of novel material formulations. The aim of the study was to compare the retrograde obturation quality of the following materials: calcium silicate (Biodentine; Septodont, Saint-Maur-des-Fosses, France), mineral trioxide aggregate (MTA+; Cerkamed Company, Stalowa Wola, Poland), and glass ionomer cement (Fuji IX; GC Corporation, Tokyo, Japan). Methods: Materials' wettability was calculated concerning the contact angles of the cements measured using a glycerol drop. Cements' porosity was determined using mercury intrusion porosimetry and micro computed tomographic (mu CT) imaging. Extracted upper human incisors were retrofilled, and mu CT analysis was applied to calculate the volume of the gap between the retrograde filling material and root canal dentin. Experiments were performed before and after soaking the materials in simulated body fluid (SBF). Results: No statistically significant differences were found among the contact angles of the studied materials after being soaked in SBF. The material with the lowest nanoporosity (Fuji IX: 2.99% and 4.17% before and after SBF, respectively) showed the highest values of microporosity (4.2% and 3.1% before and after SBF, respectively). Biodentine had the lowest value of microporosity (1.2% and 0.8% before and after SBF, respectively) and the lowest value of microgap to the root canal wall ({[}10 +/- 30] x 10(-3) mm(3)). Conclusions: Biodentine and MTA possess certain advantages over Fuji IX for hermetic obturation of retrograde root canals. Biodentine shows a tendency toward the lowest marginal gap at the cement-to-dentin interface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Compliant alkali silicate sealing glass for solid oxide fuel cell applications: Combined stability in isothermal ageing and thermal cycling with YSZ coated ferritic stainless steels

An alkali-containing silicate glass (SCN-1) is currently being evaluated as a candidate sealing glass for solid oxide fuel cell (SOFC) applications. The glass contains about 17 mole% alkalis (K+Na) and has low glass transition and softening temperatures. It remains vitreous and compliant around 750-800oC after sealing without substantial crystallization, as contrary to conventional glass-ceramic sealants, which experience rapid crystallization after the sealing process. The glassy nature and low characteristic temperatures can reduce residual stresses and result in the potential for crack healing. In a previous study, the glass was found to have good thermal cycle stability and was chemically compatible with YSZ coating during short term testing. In the current study, the compliant glass was further evaluated in a more realistic way in that the sealed glass couples were first isothermally aged for 1000h followed by thermal cycling. High temperature leakage was measured. The chemical compatibility was also investigated with powder mixtures at 700 and 800oC to enhance potential interfacial reaction. In addition, interfacial microstructure was examined with scanning electron microscopy and evaluated with regard to the leakage and chemical compatibility results.

30 DIRECT ENERGY CONVERSION↗

Sensitized red luminescence from Ce{sup 3+}, Mn{sup 2+}-doped glaserite-type alkaline-earth silicates

Bright red luminescence is observed from Ce, Mn-doped glaserite-type alkaline-earth silicates with M{sub 2}BaMgSi{sub 2}O{sub 8} (M: Ba, Sr, Ca) chemical composition. Under UV excitation, Ce-doped M{sub 2}BaMgSi{sub 2}O{sub 8} exhibits strong near-UV emission with asymmetric peak shape. UV-excited Mn-doped M{sub 2}BaMgSi{sub 2}O{sub 8} compounds show visible red emission only when Ce{sup 3+} ions are doped together. These results indicate that Mn{sup 2+}-derived red emission is caused by an efficient energy transfer from Ce{sup 3+} to Mn{sup 2+}. The red emission becomes intense with an increase in Ba-amount. This trend originates from the relaxation of the selection rule for 3d-3d transition in Mn{sup 2+} ions, which is caused by the structural deformation due to Ba{sup 2+} occupation for layer-pockets. - Graphical abstract: Glaserite-type red emitting phosphor, M{sub 2}BaMgSi{sub 2}O{sub 8}: Ce{sup 3+}, Mn{sup 2+} (M: Ba, Sr, Ca), was prepared by solid state reaction. Under UV excitation, Mn{sup 2+}-derived red emission is observed from the compounds only when Ce{sup 3+} ions are codoped, indicating that the red emission is caused by an energy transfer from Ce{sup 3+} to Mn{sup 2+}.

36 MATERIALS SCIENCE↗

Crystal structure study of new lanthanide silicates with silico-carnotite structure

The crystal structures of new rare earth-based silicate compounds (Ca{sub 3}Eu{sub 2}Si{sub 3}O{sub 12}, Ca{sub 3}Gd{sub 2}Si{sub 3}O{sub 12}, Ca{sub 3}Dy{sub 2}Si{sub 3}O{sub 12}, Ca{sub 3}Er{sub 2}Si{sub 3}O{sub 12} and Ca{sub 3}Lu{sub 2}Si{sub 3}O{sub 12}) have been determined using powder X-ray diffraction. From Rietveld refinement calculations on the collected powder patterns we observe a different distribution of the rare earth ions on the three available crystal sites characterized by different coordination numbers, depending on the ionic radius of the rare earth ion. The reasons of the instability of the silico-carnotite structure for lanthanide ions larger than Eu{sup 3+} have been deduced. In addition, in order to detect crystal phase transitions, the powder patterns of Ca{sub 3}Eu{sub 2}Si{sub 3}O{sub 12} and Ca{sub 3}Sm{sub 2}Si{sub 3}O{sub 12} samples have been collected as a function of the temperature (RT-1000 Degree-Sign C range), but no phase transitions have been observed. - Graphical abstract: Synchrotron X-ray diffraction allows us the accurate determination of the RE{sup 3+} ions distribution on the three available crystal sites of the silico-carnotite structure. Highlights: Black-Right-Pointing-Pointer The structure of the Ca{sub 3}M{sub 2}Si{sub 3}O{sub 12} (M=Eu, Gd, Dy, Er and Lu) was determined. Black-Right-Pointing-Pointer Different distribution of RE{sup 3+} ions on the three available crystal sites was observed. Black-Right-Pointing-Pointer The instability of the silico-carnotite structure for RE=La{yields}Sm was discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Well-aligned polycrystalline lanthanum silicate oxyapatite grown by reactive diffusion between solid La{sub 2}SiO{sub 5} and gases [SiO+1/2O{sub 2}]

The c-axis-oriented polycrystalline lanthanum silicate oxyapatite, La{sub 9.48}(Si{sub 5.89}□{sub 0.11})O{sub 26} (□ denotes a vacancy in the Si site), was successfully prepared by the reactive diffusion between randomly grain-oriented La{sub 2}SiO{sub 5} polycrystal and [SiO+1/2O{sub 2}] gases at 1873 K in Ar atmosphere. The polycrystal was characterized using optical microscopy, scanning electron microscopy equipped with energy dispersive X-ray spectroscopy, micro-Raman spectroscopy, X-ray diffractometry, and impedance spectroscopy. The crystal structure (space group P6{sub 3}/m) showed the deficiency of Si site at ca. 1.9%. The bulk oxide-ion conductivity along the grain-alignment direction steadily increased from 9.2 × 10{sup −3} to 1.17 × 10{sup −2} S/cm with increasing temperature from 923 to 1073 K. The activation energy of conduction was 0.23(2) eV. - Graphical abstract: We have successfully prepared the highly c-axis-oriented polycrystalline La{sub 9.48}(Si{sub 5.89}□{sub 0.11})O{sub 26} by the reactive diffusion between randomly grain-oriented La{sub 2}SiO{sub 5} polycrystal and [SiO + 1/2O{sub 2}] gases at 1873 K in Ar atmosphere. The crystal structure (space group P6{sub 3}/m) showed the deficiency of Si site of ca. 1.9%. - Highlights: • The c-axis-oriented polycrystalline La{sub 9.48}(Si{sub 5.89}□{sub 0.11})O{sub 26} is successfully prepared. • Crystal structure of La{sub 9.48}(Si{sub 5.89}□{sub 0.11})O{sub 26} is determined by single-crystal XRD. • The polycrystal shows relatively high oxide ion conductivity along the common c-axis. • Reactive diffusion is successfully used for the preparation of grain-aligned ceramics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗