SEARCH · Engineering Papers

Results for “SIDE EFFECTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

All sources NASA NTRS DOE OSTI

NASA NTRS2015

Cost Scaling of a Real-World Exhaust Waste Heat Recovery Thermoelectric Generator: A Deeper Dive

Cost is equally important to power density or efficiency for the adoption of waste heat recovery thermoelectric generators (TEG) in many transportation and industrial energy recovery applications. In many cases the system design that minimizes cost (e.g., the $/W value) can be very different than the design that maximizes the system's efficiency or power density, and it is important to understand the relationship between those designs to optimize TEG performance-cost compromises. Expanding on recent cost analysis work and using more detailed system modeling, an enhanced cost scaling analysis of a waste heat recovery thermoelectric generator with more detailed, coupled treatment of the heat exchangers has been performed. In this analysis, the effect of the heat lost to the environment and updated relationships between the hot-side and cold-side conductances that maximize power output are considered. This coupled thermal and thermoelectric treatment of the exhaust waste heat recovery thermoelectric generator yields modified cost scaling and design optimization equations, which are now strongly dependent on the heat leakage fraction, exhaust mass flow rate, and heat exchanger effectiveness. This work shows that heat exchanger costs most often dominate the overall TE system costs, that it is extremely difficult to escape this regime, and in order to achieve TE system costs of $1/W it is necessary to achieve heat exchanger costs of $1/(W/K). Minimum TE system costs per watt generally coincide with maximum power points, but Preferred TE Design Regimes are identified where there is little cost penalty for moving into regions of higher efficiency and slightly lower power outputs. These regimes are closely tied to previously-identified low cost design regimes. This work shows that the optimum fill factor Fopt minimizing system costs decreases as heat losses increase, and increases as exhaust mass flow rate and heat exchanger effectiveness increase. These findings have profound implications on the design and operation of various thermoelectric (TE) waste heat 3 recovery systems. This work highlights the importance of heat exchanger costs on the overall TEG system costs, quantifies the possible TEG performance-cost domain space based on heat exchanger effects, and provides a focus for future system research and development efforts.

cost analysis↗

NASA NTRS2009

Longitudinal Proximity Effects in Superconducting Transition-Edge Sensors

We have found experimentally that the critical current of a square thin-film superconducting transition-edge sensor (TES) depends exponentially upon the side length L and the square root of the temperature T, a behavior that has a natural theoretical explanation in terms of longitudinal proximity effects if the TES is regarded as a weak link between superconducting leads. As a consequence, the effective transition temperature T(sub c) of the TES is current-dependent and at fixed current scales as 1/L(sup 2). We also have found that the critical current can show clear Fraunhofer-like oscillations in an applied magnetic field, similar to those found in Josephson junctions. We have observed the longitudinal proximity effect in these devices over extraordinarily long lengths up to 290 micrometers, 1450 times the mean-free path.

Sadlier, John E.↗

NASA NTRS2010

Longitudinal Proximity Effects in Superconducting Transition-Edge Sensors

Sadleir, John E.↗

NASA NTRS2013

Analysis of Handling Qualities Design Criteria for Active Inceptor Force-Feel Characteristics

The force-feel system characteristics of the cyclic inceptors of most helicopters are set based on the characteristics of the mechanical components in the control system (mass, springs, friction dampers, etc.). For these helicopters, the force-feel characteristics typically remain constant over the entire flight envelope, with perhaps a trim release to minimize control forces while maneuvering. With the advent of fly-by-wire control systems and active inceptors in helicopters, the force-feel characteristics are now determined by the closed-loop response of the active inceptor itself as defined by the inertia, force/displacement gradient, damping, breakout force and detent shape configuration parameters in the inceptor control laws. These systems give the flexibility to dynamically prescribe different feel characteristics for different control modes or flight conditions, and the ability to provide tactile cueing to the pilot through the actively controlled side-stick or center-stick cyclic inceptor. For rotorcraft, a few studies have been conducted to assess the effects of cyclic force-feel characteristics on handling qualities in flight. An early study provided valuable insight into the static force-deflection characteristics (force gradient) and the number of axes controlled by the side-stick controller for the U.S. Army's Advanced Digital/Optical Control System (ADOCS) demonstrator aircraft [1]. The first of a series of studies providing insight on the inceptor dynamic force-feel characteristics was conducted on the NASA/Army CH-47B variable-stability helicopter [2]. This work led to a proposed requirement that set boundaries based on the cyclic natural frequency and inertia, with the stipulation of a lower damping ratio limit of 0.3 [3]. A second study was conducted by the Canadian Institute for Aerospace Research using their variable-stability Bell 205A helicopter [4]. This research suggested boundaries for stick dynamics based on natural frequency and damping ratio. While these two studies produced boundaries for acceptable/unacceptable stick dynamics for rotorcraft, they were not able to provide guidance on how variations of the stick dynamics in the acceptable region impact handling qualities. More recently, a ground based simulation study [5] suggested little benefit was to be obtained from variations of the damping ratio for a side-stick controller exhibiting high natural frequencies (greater than 17 rad/s) and damping ratios (greater than 2.0). A flight test campaign was conducted concurrently on the RASCAL JUH-60A in-flight simulator and the ACT/FHS EC-135 in flight simulator [6]. Upon detailed analysis of the pilot evaluations the study identified a clear preference for a high damping ratio and natural frequency of the center stick inceptors. Side stick controllers were found to be less sensitive to the damping. While these studies have compiled a substantial amount of data, in the form of qualitative and quantitative pilot opinion, a fundamental analysis of the effect of the inceptor force-feel system on flight control is found to be lacking. The study of Ref. [6] specifically concluded that a systematic analysis was necessary, since discrepancies with the assigned handling qualities showed that proposed analytical design metrics, or criteria, were not suitable. The overall goal of the present study is to develop a clearer fundamental understanding of the underlying mechanisms associated with the inceptor dynamics that govern the handling qualities using a manageable analytical methodology.

Malpica, Carlos A.↗

NASA NTRS2004

The Office of Inspector General (OIG)

The NASA Office of Inspector General is the Federal Law Enforcement Agency at NASA which conducts criminal and regulatory investigations in which NASA is a victim. The OIG prevents and detects crime, fiaud, waste and abuse and assists NASA management in promoting economy, efficiency, and effectiveness in its programs and operations. Investigations (OI) and the Office of Audits (OA). The investigations side deals with criminal Investigations, administrative investigations, and civil investigations. The Audits side deals with inspections and assessments as well as the Auditing of NASA Programs and Activities. Our mission at the OIG is to conduct and supervise independent and objective audits and investigations relating to agency programs and operations; to promote economy, effectiveness and efficiency within the agency; to prevent and detect crime, fraud, waste and abuse in agency programs and operations; to review and make recommendations regarding existing and proposed legislation and regulations relating to agency programs and operations. We are also responsible for keeping the agency head and the Congress fully and currently informed of problems in agency programs and operations. deal with False Claims, False Statements, Conspiracy, Theft, Computer Crime, Mail Fraud, the Procurement Integrity Act, the Anti-Kickback Act, as well as noncompliance with NASA Management Instructions, the Federal Acquisition Regulations (FAR), and the Code of Federal Regulations (CFR). Most of the casework that is dealt with in our office is generated through gum shoe work or cases that we generate on our own. These cases can come from Law Enforcement Referrals, GIDEP Reports, EPlMS (NASA Quality System), Defense Contract Audit Agency, Newspaper Articles, and Confidential Information. In many cases, confidentiality is the biggest factor to informants coming forward. We are able to maintain confidentiality because the 01 is independent of NASA Management and doesn t report to the Center Directors, therefore the informant s mangers and supervisors are unaware of the informants actions. The only time when an informant s confidentiality may be compromised is when it is needed in a Court of Law and is released through a Judicial Court Order. During my tenure here at the NASA OIG/OI at Glenn Research Center, I have been involved in many different tasks. They have ranged from updating Suspected Unapproved Parts case files to independently interviewing NASA employees to turn up general background information. The 01 has the duty of informing NASA aeronautical safety managers of potential Nonconforming products. My mission is to compile a database of Nonconformance reports for distribution. The background information that I turn up from my interviews is then used to determine NASA s susceptibility to acceptance of unapproved parts. The IG organization is divided up into two separate disciplines, the Office of 01 investigations primarily focus on violations of Federal laws. Some of these violations

Macisco, Christopher A.↗

NASA NTRS1975

Effect of symmetrical vortex shedding on the longitudinal aerodynamic characteristics of wing-body-tail combinations

An engineering prediction method for determining the longitudinal aerodynamic characteristics of wing-body-tail combinations is developed. The method includes the effects of nonlinear aerodynamics of components and the interference between components. Nonlinearities associated with symmetrical vortex shedding from the nose of the body are considered as well as the nonlinearities associated with the separation vortices from the leading edges and side edges of the lifting surfaces. The wing and tail characteristics are calculated using lifting surface theories which include effects of incidence, camber, twist, and induced velocities from external sources of disturbance such as bodies and vortices. The lifting surface theories calculate the distribution of leading edge and side edge suction which is converted to vortex lift using the Polhamus suction analogy. Correlation curves are developed to determine the fraction of the theoretical suction force which is converted into vortex lift. The prediction method is compared with experimental data on a variety of aircraft configurations to assess the accuracy and limitations of the method.

Mendenhall, M. R.↗

NASA NTRS1990

Unsteady surface pressure distributions on a delta wing undergoing large amplitude pitching motions

Wind tunnel experiments were performed on a 70-deg-sweep delta wing to determine the effect of a sinusoidal pitching motion on the pressure field on the suction side of the wing. Pressure taps were placed from 35-90 percent of the chord, at 60 percent of the local semi-span. Pressure coefficients were measured as functions of Reynolds number and pitch rate. The surface pressure distribution was seen to vary at the same frequency as the pitching frequency, though distortion due to the vortex breakdown was observed. Comparing the upstroke (angle of attack increasing) and downstroke (angle of attack decreasing) pressures for a specific angle of attack, a time lag in the pressure distribution was observed. The downstroke pressures were slightly larger at the forward chord locations. Vortex breakdown was seen to have the most significant effect at the 40-45-percent chord location, where an increase in local pressure was apparent, as well as a distortion of the periodic pressure fluctuation.

Thompson, S. A.↗

NASA NTRS1994

Wind Tunnel Results of Pneumatic Forebody Vortex Control Using Rectangular Slots a Chined Forebody

A subsonic wind tunnel investigation of pneumatic vortex flow control on a chined forebody using slots was accomplished at a dynamic pressure of 50 psf resulting in a R(n)/ft of 1.3 x 10(exp 6). Data were acquired from angles of attack ranging from -4deg to +34deg at side slips of +0.4deg and +10.4deg. The test article used in this study was the 10% scale Fighter Lift and Control (FLAC) advanced diamond winged, vee-tailed fighter configuration. Three different slot blowing concepts were evaluated; outward, downward, and tangential with ail blowing accomplished asymmetrically. The results of three different mass flows (0.067, 0.13, and 0.26 lbm/s; C(sub mu)'s of less than or equal to 0.006, 0.011. and 0.022 respectively) were analyzed and reported. Test data are presented on the effects of mass flows, slot lengths and positions and blowing concepts on yawing moment and side force generation. Results from this study indicate that the outward and downward blowing slots developed yawing moment and side force increments in the direction opposite of the blowing side while the tangential blowing slots generated yawing moment and side force increments in the direction towards the blowing side. The outward and downward blowing slots typically produced positive pitching moment increments while the tangential blowing slots typically generated negative pitching moment increments. The slot blowing nearest the forebody apex was most effective at generating the largest increments and as the slot was moved aft or increased in length, its effectiveness at generating forces and moments diminished.

Alexander, Michael↗

NASA NTRS1989

Surface pressure distributions on a delta wing undergoing large amplitude pitching oscillations

Wind tunnel experiments were performed on a 70 deg sweep delta wing to determine the effect of a sinusoidal pitching motion on the pressure field on the suction side of the wing. Twelve pressure taps were placed from 35 to 90 percent of the chord, at 60 percent of the local semi-span. Pressure coefficients were measured as a function of Reynolds number and pitch rate. The pressure coefficient was seen to vary at approximately the same frequency as the pitching frequency. The relative pressure variation at each chord location was comparable for each case. The average pressure distribution through each periodic motion was near the static distribution for the average angle of attack. Upon comparing the upstroke and downstroke pressures for a specific angle of attack, the downstroke pressures were slightly larger. Vortex breakdown was seen to have the most significant effect at the 40 to 45 percent chord location, where a decrease in pressure was apparent.

Thompson, Scott A.↗

NASA NTRS1992

Effect of free surface shape on combined thermocapillary and natural convection

Combined thermocapillary and natural convection in an open square cavity with differentially-heated side walls is studied numerically as well as experimentally. The test fluid is silicone oil with Prandtl number of 105. The shape of fluid-free surface is made either flat or curved to study its effect on the flow. A finite difference scheme to deal with a curved free surface is developed. The experimental results shown agree with the numerical results. With the curved-free surface, the flow and local heat transfer rate are reduced in the corner regions, and a sharp peak in heat transfer rate at the top edge of the cold wall disappears.

Kamotani, Yasuhiro↗

NASA NTRS1972

Effects of spanwise rotation on the structure of two-dimensional fully developed turbulent channel flow.

Experiments on fully developed turbulent flow in a channel which is rotating at a steady rate about a spanwise axis are described. The Coriolis force components in the region of two-dimensional mean flow affect both local and global stability. Three stability-related phenomena were observed or inferred: (1) the reduction (increase) of the rate of wall-layer streak bursting in locally stabilized (destabilized) wall layers; (2) the total suppression of transition to turbulence in a stabilized layer; (3) the development of large-scale roll cells on the destabilized side of the channel by growth of a Taylor-Gortler vortex instability. Local effects of rotational stabilization, such as reduction of the turbulent stress in wall layers, can be related to the local Richardson number in a simple way. This paper not only investigates this effect, but also, by methods of flow visualization, exposes some of the underlying structure changes caused by rotation.-

Johnston, J. P.↗

NASA NTRS2003

Modified Laser Flash Method for Thermal Properties Measurements and the Influence of Heat Convection

The study examined the effect of natural convection in applying the modified laser flash method to measure thermal properties of semiconductor melts. Common laser flash method uses a laser pulse to heat one side of a thin circular sample and measures the temperature response of the other side. Thermal diffusivity can be calculations based on a heat conduction analysis. For semiconductor melt, the sample is contained in a specially designed quartz cell with optical windows on both sides. When laser heats the vertical melt surface, the resulting natural convection can introduce errors in calculation based on heat conduction model alone. The effect of natural convection was studied by CFD simulations with experimental verification by temperature measurement. The CFD results indicated that natural convection would decrease the time needed for the rear side to reach its peak temperature, and also decrease the peak temperature slightly in our experimental configuration. Using the experimental data, the calculation using only heat conduction model resulted in a thermal diffusivity value is about 7.7% lower than that from the model with natural convection. Specific heat capacity was about the same, and the difference is within 1.6%, regardless of heat transfer models.

Lin, Bochuan↗

NASA NTRS1983

Surface pressures induced on a flat plate with in-line and side-by-side dual jet configurations

A jet in a crossflow is of interest in numerous practical situations including jet-powered VTOL aircraft. Two aspects of the problem have received little prior study. First is the effect of the angle of the jet to the crossflow. Second is the performance of dual-jet configurations both in-line and side-by-side. The test plan for this work was designed to address these two aspects. The experiments were conducted in the 7 x 10 tunnel at NASA Ames at velocities from 14.5 - 35.8 m/sec (47.6 - 117.4 ft/sec.). Detailed pressure distributions are presented for single and dual jets over a range of velocity ratios from 3 to 8, spacings from 2 to 6 diameters and injection angles of 90, 75, and 105 degrees. The effects of the various parameters and the differences between the axisymmetric and flat plate geometries on the nature, size, shape, and strength of the interaction regions on the body surfaces are shown.

Schetz, J. A.↗

NASA NTRS1952

A theoretical and experimental investigation of the effects of yaw on pressures, forces, and moments during seaplane landings and planing

A theory for the side force, rolling moment, yawing moment, and pressure distribution during yawed landings and planing of seaplanes was developed. For the special case of the straight-sided wedge without chine immersion, the results of the theoretical analysis are presented in the form of generalized curves covering all step landing conditions. Experimental impact and planing data are presented for a prismatic wedge having an angle of dead rise of 22.5 degrees and are shown to be in reasonable agreement with the theoretical predictions.

LOADS, LANDING - IMPACT, WATER↗

NASA NTRS1972

Propellant sidefeed-short pulse discharge thruster studies

The technique of feeding a solid propellant into the discharge from the sides of the discharge was evaluated. The thrust/power ratio could be significantly effected by the included angle of V-shaped propellants and by the electrode length. This result implies that when results are compared at the same specific impulse it is possible to obtain higher thrust efficiencies. In particular, it was found that for a given discharge energy the thrust/power ratio correlated with propellant mass. Increasing the integral simultaneously increases both the gas dynamic and electromagnetic thrust. An analytic expression was formulated for ablated mass which comprehensively describes experimental data in terms of geometry and electrical parameters. The correlation of the product impulse x specific impulse with discharge energy was also described. It is suggested that the reliability of dry energy storage capacitors does not equal the reliability of liquid impregnated units when the comparison is made at the same joules/Kg rating.

Palumbo, D. J.↗

NASA NTRS1977

Static and wind-on tests of an upper-surface-blown jet-flap nozzle arrangement for use on the Quiet Clean Short-haul Experimental Engine (QCSEE)

The internal aerodynamic performance, the static turning characteristics, and the forward-speed characteristics of two 1/12-scale upper surface-blown jet-flap exhaust-nozzle arrangements designed for use on the Quiet Clean Short-Haul Experimental Engine (QCSEE) were investigated. The nozzles were equipped with interchangeable area-control side doors in the aft sidewalls of the nozzle so that the effective nozzle area could be varied over a wide range. A simulated wing was used to evaluate installation losses for the nozzles. A smoothly curved flap was attached to the trailing edge of the simulated wing to allow an evaluation of the static turning characteristics of the nozzle arrangement. Forward-speed effects on the jet turning characteristics of the QCSEE nozzles were evaluated by mounting a single engine on a semispan wing designed to be representative of a four-engine STOL transport configuration.

Phelps, A. E., III↗

NASA NTRS1978

The execution of systematic measurements on plane cascades

The present state of development of the experimental technique regarding the flow through cascades and several points to be specially observed in the design of cascade wind tunnels were discussed. The equations required for the evaluation of the momentum measurements in two dimensional flow through cascades were developed. Regarding the effect of the jet contraction due to the boundary layer along the side walls a simple method for correction was also given in order to obtain two dimensional flow characteristics. Also given were the equations for the evaluation of the pressure distribution measurements. Another contribution was made regarding the presentation of the test results in the form of nondimensional quantities. The results of systematic measurements of cascades with symmetrical aerofoil were reported, and the above suggested method was applied for the evaluation of the measurements.

Scholz, N.↗

NASA NTRS1978

Computer image processing: Geologic applications

Computer image processing of digital data was performed to support several geological studies. The specific goals were to: (1) relate the mineral content to the spectral reflectance of certain geologic materials, (2) determine the influence of environmental factors, such as atmosphere and vegetation, and (3) improve image processing techniques. For detection of spectral differences related to mineralogy, the technique of band ratioing was found to be the most useful. The influence of atmospheric scattering and methods to correct for the scattering were also studied. Two techniques were used to correct for atmospheric effects: (1) dark object subtraction, (2) normalization of use of ground spectral measurements. Of the two, the first technique proved to be the most successful for removing the effects of atmospheric scattering. A digital mosaic was produced from two side-lapping LANDSAT frames. The advantages were that the same enhancement algorithm can be applied to both frames, and there is no seam where the two images are joined.

Abrams, M. J.↗