Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RUPTURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Creep of A508/533 Pressure Vessel Steel

ABSTRACT Evaluation of potential Reactor Pressure Vessel (RPV) steels has been carried out as part of the pre-conceptual Very High Temperature Reactor (VHTR) design studies. These design studies have generally focused on American Society of Mechanical Engineers (ASME) Code status of the steels, temperature limits, and allowable stresses. Initially, three candidate materials were identified by this process: conventional light water reactor (LWR) RPV steels A508 and A533, 2¼Cr-1Mo in the annealed condition, and Grade 91 steel. The low strength of 2¼Cr-1Mo at elevated temperature has eliminated this steel from serious consideration as the VHTR RPV candidate material. Discussions with the very few vendors that can potentially produce large forgings for nuclear pressure vessels indicate a strong preference for conventional LWR steels. This preference is based in part on extensive experience with forging these steels for nuclear components. It is also based on the inability to cast large ingots of the Grade 91 steel due to segregation during ingot solidification, thus restricting the possible mass of forging components and increasing the amount of welding required for completion of the RPV. Grade 91 steel is also prone to weld cracking and must be post-weld heat treated to ensure adequate high-temperature strength. There are also questions about the ability to produce, and very importantly, verify the through thickness properties of thick sections of Grade 91 material. The availability of large components, ease of fabrication, and nuclear service experience with the A508 and A533 steels strongly favor their use in the RPV for the VHTR. Lowering the gas outlet temperature for the VHTR to 750°C from 950 to 1000°C, proposed in early concept studies, further strengthens the justification for this material selection. This steel is allowed in the ASME Boiler and Pressure Vessel Code for nuclear service up to 371°C (700°F); certain excursions above that temperature are allowed by Code Case N-499-2 (now incorporated as an appendix to Section III Division 5 of the Code). This Code Case was developed with a rather sparse data set and focused primarily on rolled plate material (A533 specification). Confirmatory tests of creep behavior of both A508 and A533 are described here that are designed to extend the database in order to build higher confidence in ensuring the structural integrity of the VHTR RPV during off-normal conditions. A number of creep-rupture tests were carried out at temperatures above the 371°C (700°F) Code limit; longer term tests designed to evaluate minimum creep behavior are ongoing. A limited amount of rupture testing was also carried out on welded material. All of the rupture data from the current experiments is compared to historical values from the testing carried out to develop Code Case N-499-2. It is shown that the A508/533 basemetal tested here fits well with the rupture behavior reported from the historical testing. The presence of weldments significantly reduces the time to rupture. The primary purpose of this report is to summarize and record the experimental results in a single document.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Seismic Analysis of Spatio-Temporal Fracture Generation During EGS Resource Development

This DOE GTO funded project was a collaborative effort between Array Information Technology and the University of California at Berkeley. The project goal is to improve technology to assess in-situ stress magnitude and orientation, kinematic fracture parameters, rupture size, rupture orientation as well as temporal changes and volumetric distribution of the injected fluid during Enhanced Geothermal System (EGS) resource development. The project leveraged high-frequency seismic data recorded by the LBNL 34-station permanent geophone network and seismic broadband data recorded by a temporary 33-station seismometer network that operated in The Geysers during the injection phase of the DOE GTO funded EGS demonstration project at the well Prati-32. The operation of the broadband network with high station density and good azimuthal coverage to monitor the injection phase produced an unprecedented dataset that is typically unavailable for EGS operations. The two datasets offer the advantages of studying the parameters under investigation over a broader frequency band and the higher sensitivity of the broadband seismometers resulted in a richer dataset with a lower magnitude of completeness. Moment tensor (MT) inversion have been employed to develop a catalog of earthquake source solutions including moment tensor and finite source rupture area. This resulted in a 168-event waveform-based seismic moment tensor catalog for events 0.7≤Mw≤3.9 based on a semi-automated moment tensor analysis technique. The MT solutions were used for in-situ stress estimation during the EGS injection phases. We found an approximate 15-degree counterclockwise rotation of the least compressive stress sigma-3, and a rotation of the maximum compressive stress sigma-1 toward the vertical as the injected volume of water increased. We developed a rupture-area magnitude scaling relationship of The Geysers earthquakes obtained from finite-source inversion for fault slip that reveals a very high correlation to published results. Based on the rupture area-magnitude relationship we mapped Mw from the LBNL earthquake catalog to estimate the activated fracture area, its location and orientation within the injection volume of Prati-32. The double-difference Wadati (DDW) technique was applied to high-accuracy P- and S-wave differential travel times derived from waveform cross correlation to image fluid saturation in the subsurface based on Vp/Vs-ratio. The recently developed technique has been applied to estimate temporal changes of fluid distribution in fault zones and in volcanic regions but not yet in engineered geo-reservoirs. The improvement of the technology includes high-resolution waveform cross correlation applied to the high-quality datasets with lower magnitude of completeness resulting in a higher number of recorded events. The improvement allowed to estimate both, the spatial and temporal distribution of injected fluids and the state of the injected fluid during reservoir stimulation. Results of the DDW analysis revealed the development of an injection-derived steam plume during the early injection phase, particularly in the northern part of the Prati-32 study area.

15 GEOTHERMAL ENERGY↗

Initial study of notch sensitivity of Grade 91 using mechanisms motivated crystal plasticity finite element method

This report describes the development of a crystal plasticity finite element method (CPFEM) model for the multiaxial creep rupture of Grade 91 steel. The report demonstrates that core blocks in heat pipe reactor designs will see significantly different stress states than those typically found in conventional advanced reactor components where structures can often be represented as thin-walled pressure vessels. Current design practice uses effective stress measures calibrated to biaxial creep test data to account for the effect of stress multiaxiality on rupture life. Because these models rely on biaxial data they may not be accurate for the truly 3D, triaxial states found in heat pipe microreactor core blocks. A physically-based model, like the CPFEM model developed here, may be able to more accurately represent creep rupture under triaxial stresses when compared to conventional, empirical methods. This report describes the development, implementation, and validation of such a model and then applies the model to predict the effect of stress triaxiality on rupture in Grade 91 steel. The model results are used to assess the effective stress measures currently used in high temperature design codes and makes specific recommendations on improving these effective stresses to better account for the effect of 3D stress states on rupture in Grade 91. The validation and then implementation of these recommendations in design codes and standards could lead to safer, more effective heat pipe microreactor core block designs.

36 MATERIALS SCIENCE↗

Anisotropy of nickel-base superalloy single crystals

The influence of orientation on the tensile and stress rupture behavior of 52 Mar-M247 single crystals was studied. Tensile tests were performed at temperatures between 23 and 1093 C; stress rupture behavior was examined between 760 and 1038 C. The mechanical behavior of the single crystals was rationalized on the basis of the Schmid factor contours for the operative slip systems and the lattice rotations which the crystals underwent during deformation. The tensile properties correlated well with the appropriate Schmid factor contours. The stress rupture lives at lower testing temperatures were greatly influenced by the lattice rotations required to produce cross slip. A unified analysis was attained for the stress rupture life data generated for the Mar-M247 single crystals at 760 and 774 C under a stress of 724 MPa and the data reported for Mar-M200 single crystals tested at 760 C under a stress of 689 MPa. Based on this analysis, the stereographic triangle was divided into several regions which were rank ordered according to stress rupture life for this temperature regime.

Mackay, R. A.↗

Analysis of coseismic surface displacement gradients using radar interferometry: New insights into the Landers earthquake

The map of the coseismic displacement field generated by interferometric processing of synthetic aperture radar (SAR) images taken before and after the June 28, 1992, Landers earthquake sequence brings new insights into the nature of deformation caused by these earthquakes. We use the interferometric map generated by Massonnet et al. (1993) to analyze the surface displacement field in the vicinity of the fault trace. Complexities in the fringe pattern near the fault reflect short-wavelength variations of the surface rupture and slip distribution, and attest to large displacement gradients. Along two sections of the fault, characteristic fringe patterns can be recognized, contrasting in density and direction with patterns observed away from the rupture. In order to understand the observed fringe patterns, we compute synthetic interferograms in three simple cases: (1) rigid-body rotations about a vertical axis, (2) about a horizontal axis (tilt), and (3) distributed, simple shear. The orientation and spatial separation of interferometric fringes predicted by these models help constrain near-field deformation and rupture parameters. Where the Kickapoo fault connects with the Homestead Valley fault, the interferogram shows a clear pattern of parallel N20 deg W fringes separated by about 160 m. This pattern and vertical offsets measured along the Kickapoo fault suggest that the block between this fault and the Johnson Valley fault may have been tilted, down to the west. A 5-km block lifted by 1 m on one side would be tilted by an angle of 0.01 deg (190 microrad), producing fringes separated by about 160 m, parallel to the tilt axis. Such a tilt, parallel to a N20 deg W direction, would account for the gradual, northward increase of the vertical slip component observed along the Kickapoo fault. This tilt may also explain the 1 m of reverse slip observed along the 'slip gap' section of the Homestead Valley break. Between the southern end of the Johnson Valley fault and the Eureka Peak fault, where no surface rupture has been mapped, the dense pattern of fringes implies distributed shear, probably resulting from fault slip at depth. The density and direction of the fringes in the gap are consistent with a right-lateral slip of 1.2-3.8 m on a blind fault locked above the depth of 1.5-2 km. Such observations of small wavelength features in the SAR interferogram bring new insights into the near-field displacement gradient and thus on response of the uppermost crust to seismic rupture.

Peltzer, Gilles↗

Time/Temperature Dependent Tensile Strength of SiC and Al2O3-Based Fibers

In order to understand and model the thermomechanical behavior of fiber-reinforced composites, stress-rupture, fast-fracture, and warm-up rupture studies were conducted on various advanced SiC and Al2O3-based fibers in the,temperature range from 20 to 1400 C in air as well as in inert environments. The measured stress-rupture, fast fracture, and warm-up rupture strengths were correlated into a single master time/temperature-dependent strength plot for each fiber type using thermal activation and slow crack growth theories. It is shown that these plots are useful for comparing and selecting fibers for CMC and MMC reinforcement and that, in comparison to stress rupture tests, the fast-fracture and warm-up tests can be used for rapid generation of these plots.

Yun, Hee Mann↗

Numerical study on spontaneous ignition of pressurized hydrogen release through a length of tube

The issue of spontaneous ignition of highly pressurized hydrogen release is of important safety concern, e.g. in the assessment of risk and design of safety measures. This paper reports on recent numerical investigation of this phenomenon through releases via a length of tube. This mimics a potential accidental scenario involving release through instrument line. The implicit large eddy simulation (ILES) approach was used with the 5th-order weighted essentially non-oscillatory (WENO) scheme. A mixture-averaged multi-component approach was used for accurate calculation of molecular transport. The thin flame was resolved with fine grid resolution and the autoignition and combustion chemistry were accounted for using a 21-step kinetic scheme. The numerical study revealed that the finite rupture process of the initial pressure boundary plays an important role in the spontaneous ignition. The rupture process induces significant turbulent mixing at the contact region via shock reflections and interactions. The predicted leading shock velocity inside the tube increases during the early stages of the release and then stabilizes at a nearly constant value which is higher than that predicted by one-dimensional analysis. The air behind the leading shock is shock-heated and mixes with the released hydrogen in the contact region. Ignition is firstly initiated inside the tube and then a partially premixed flame is developed. Significant amount of shock-heated air and well developed partially premixed flames are two major factors providing potential energy to overcome the strong under-expansion and flow divergence following spouting from the tube. Parametric studies were also conducted to investigate the effect of rupture time, release pressure, tube length and diameter on the likelihood of spontaneous ignition. It was found that a slower rupture time and a lower release pressure will lead to increases in ignition delay time and hence reduces the likelihood of spontaneous ignition. If the tube length is smaller than a certain value, even though ignition could take place inside the tube, the flame is unlikely to be sufficiently strong to overcome under-expansion and flow divergence after spouting from the tube and hence is likely to be quenched. (author)

08 HYDROGEN↗

Long-Term Follow-Up After Endovascular Treatment of Acute Aortic Emergencies

Purpose. To investigate the long-term outcome and efficacy of emergency treatment of acute aortic diseases with endovascular stent-grafts. Methods. From September 1995 to April 2007, 37 patients (21 men, 16 women; age 53.9 {+-} 19.2 years, range 18-85 years) with acute complications of diseases of the descending thoracic aorta were treated by endovascular stent-grafts: traumatic aortic ruptures (n = 9), aortobronchial fistulas due to penetrating ulcer or hematothorax (n = 6), acute type B dissections with aortic wall hematoma, penetration, or ischemia (n = 13), and symptomatic aneurysm of the thoracic aorta (n = 9) with pain, penetration, or rupture. Diagnosis was confirmed by contrast-enhanced CT. Multiplanar reformations were used for measurement of the landing zones of the stent-grafts. Stent-grafts were inserted via femoral or iliac cut-down. Two procedures required aortofemoral bypass grafting prior to stent-grafting due to extensive arteriosclerotic stenosis of the iliac arteries. In this case the bypass graft was used for introduction of the stent-graft. Results. A total of 46 stent-grafts were implanted: Vanguard/Stentor (n = 4), Talent (n = 31), and Valiant (n = 11). Stent-graft extension was necessary in 7 cases. In 3 cases primary graft extension was done during the initial procedure (in 1 case due to distal migration of the graft during stent release, in 2 cases due to the total length of the aortic aneurysm). In 4 cases secondary graft extensions were performed-for new aortic ulcers at the proximal stent struts (after 5 days) and distal to the graft (after 8 months) and recurrent aortobronchial fistulas 5 months and 9 years after the initial procedure-resulting in a total of 41 endovascular procedures. The 30-day mortality rate was 8% (3 of 37) and the overall follow-up was 29.9 {+-} 36.6 months (range 0-139 months). All patients with traumatic ruptures demonstrated an immediate sealing of bleeding. Patients with aortobronchial fistulas also demonstrated a satisfactory follow-up despite the necessity for reintervention and graft extension in 3 of 6 cases (50%). Two patients with type B dissection died due to mesenteric ischemia despite sufficient mesenteric blood flow being restored (but too late). Two suffered from neurologic complications, 1 from paraplegia and 1 from cerebral ischemia (probably embolic), 1 from penetrating ulcer, and 1 from persistent ischemia of the kidney. Five of 9 (56%) patients with symptomatic thoracic aneurysm demonstrated endoleaks during follow-up and there was an increase in the aneurysm in 1. Conclusion. Endovascular treatment is safe and effective for emergency treatment of life-threatening acute thoracic aortic syndromes. Results are encouraging, particularly for traumatic aortic ruptures. However, regular follow-up is mandatory, particularly in the other pathologies, to identify late complications of the stent-graft and to perform appropriate additional corrections as required.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Uniaxial creep response of Alloy 800H in impure helium and in low oxygen potential environments for nuclear reactor applications.

Studies were conducted on the creep behavior of Alloy 800H in impure helium and in a 1%CO-CO{sub 2} environment. At relatively low applied stresses and at low temperatures, the presence of methane in helium reduced the rupture strain significantly while increasing the rupture life relative to the behavior in pure helium. The degradation in rupture strain is due to the occurrence of cleavage fracture in the He + CH{sub 4} environment; this explanation is also supported by high activation energy (Q = 723 kJ/mol) for creep in He + CH{sub 4}. At higher applied stresses and also at higher temperatures, creep-rupture behavior in He and He + CH{sub 4} was similar. Creep response in pure He and in CO-CO{sub 2} follows a dislocation climb-controlled power-law behavior whereas that in He + CH{sub 4} has a different behavior as indicated by the high stress exponent (n = 9.8). The activation energy for creep in pure He was 391 kJ/mol and in CO-CO{sub 2} was 398 kJ/mol, and appeared to be independent of stress in both environments. On the other hand, in He + CH{sub 4}, the activation energy (Q = 723 kJ/mol) seems to be dependent on stress.

03 NATURAL GAS↗

Real-Time Fault Tracking and Ground Motion Prediction for Large Earthquakes With HR-GNSS and Deep Learning

Earthquake early warning (EEW) systems aim to forecast the shaking intensity rapidly after an earthquake occurs and send warnings to affected areas before the onset of strong shaking. The system relies on rapid and accurate estimation of earthquake source parameters. However, it is known that source estimation for large ruptures in real-time is challenging, and it often leads to magnitude underestimation. In a previous study, we showed that machine learning, HR-GNSS, and realistic rupture synthetics can be used to reliably predict earthquake magnitude. This model, called Machine-Learning Assessed Rapid Geodetic Earthquake model (M-LARGE), can rapidly forecast large earthquake magnitudes with an accuracy of 99%. Here, we expand M-LARGE to predict centroid location and fault size, enabling the construction of the fault rupture extent for forecasting shaking intensity using existing ground motion models. We test our model in the Chilean Subduction Zone with thousands of simulated and five real large earthquakes. The result achieves an average warning time of 40.5 s for shaking intensity MMI4+, surpassing the 34 s obtained by a similar GNSS EEW model. Our approach addresses a critical gap in existing EEW systems for large earthquakes by demonstrating real-time fault tracking feasibility without saturation issues. This capability leads to timely and accurate ground motion forecasts and can support other methods, enhancing the overall effectiveness of EEW systems. Additionally, the ability to predict source parameters for real Chilean earthquakes implies that synthetic data, governed by our understanding of earthquake scaling, is consistent with the actual rupture processes.

58 GEOSCIENCES↗

Alternative Techniques for Injecting Massive Quantities of Gas for Plasma Disruption Mitigation

Injection of massive quantities of noble gases or D2 has proven to be effective at mitigating some of the deleterious effects of disruptions in tokamaks. Two alternative methods that might offer some advantages over the present technique for massive gas injection are shattering massive pellets and employing closecoupled rupture disks. Laboratory testing has been carried out to evaluate their feasibility. For the study of massive pellets, a pipe gun pellet injector cooled with a cryogenic refrigerator was fitted with a relatively large barrel (16.5 mm bore), and D2 and Ne pellets were made and were accelerated to speeds of ~600 and 300 m/s, respectively. Based on the successful proof-of-principle testing with the injector and a special double-impact target to shatter pellets, a similar system has been prepared and installed on DIII-D, with preliminary experiments already carried out. To study the applicability of rupture disks for disruption mitigation, a simple test apparatus was assembled in the lab. Commercially available rupture disks of 1 in. nominal diameter were tested at conditions relevant for the application on tokamaks, including tests with Ar and He gases and rupture pressures of ~54 bar. Some technical and practical issues of implementing this technique on a tokamak are discussed.

disruption↗

Ground-motions site and event specificity: Insights from assessing a suite of simulated ground motions in the San Francisco Bay Area

This article presents the results of a research that is part of a larger collaborative effort between the Lawrence Berkeley National Laboratory and the Pacific Earthquake Engineering Research Center, funded by the US Department of Energy Office of Cybersecurity, Energy Security and Emergency Response. The main objective of this study is to assess a suite of near and far-field simulated ground motions obtained from 20 realizations of an M7 Hayward Fault earthquake in the San Francisco Bay Area, California USA, and inform the selection of rupture simulation parameters leading to strong motions. To this aim, comparisons are conducted with NGA-W2 and directivity ground-motion models and a selected population of records. An archetypal steel moment-resisting frame is utilized to assess infrastructure response distributions. The analyses carried out for each simulated event and subdomain with consistent properties in terms of shallow shear-wave velocity proved to be instrumental for better interpreting the differences between simulated motions and empirical models. The main reasons identified for variances between simulations and empirical relationships included (1) directivity effects fully captured by the simulations across the full breadth of rupture models; (2) site vicinity to ruptures that incorporate large-slip patches, particularly if these are in the forward-directivity direction; and (3) presence of geologic structures that can “trap” seismic waves and produce ground motions with large amplitude and long signal duration. The analyses carried out in this work provide a path for interpreting ground-motion site and event specificity obtained from a suite of physics-based simulations, differing only in the rupture model characterization, to inform the selection of simulation scenarios for site-specific engineering analyses under strong excitations. Evidence from this work points to the possibility that current hazard models may underestimate ground-motion intensities in areas where the combined effect of directivity and site conditions results in large ground-motion amplitudes.

58 GEOSCIENCES↗

Verification of Allowable Stresses In ASME Section III Subsection NH For Grade 91 Steel & Alloy 800H

The database for the creep-rupture of 9Cr-1Mo-V (Grade 91) steel was collected and reviewed to determine if it met the needs for recommending time-dependent strength values, S{sub t}, for coverage in ASME Section III Subsection NH (ASME III-NH) to 650 C (1200 F) and 600,000 hours. The accumulated database included over 300 tests for 1% total strain, nearly 400 tests for tertiary creep, and nearly 1700 tests to rupture. Procedures for analyzing creep and rupture data for ASME III-NH were reviewed and compared to the procedures used to develop the current allowable stress values for Gr 91 for ASME II-D. The criteria in ASME III-NH for estimating S{sub t} included the average strength for 1% total strain for times to 600,000 hours, 80% of the minimum strength for tertiary creep for times to 600,000 hours, and 67% of the minimum rupture strength values for times to 600,000 hours. Time-temperature-stress parametric formulations were selected to correlate the data and make predictions of the long-time strength. It was found that the stress corresponding to 1% total strain and the initiation of tertiary creep were not the controlling criteria over the temperature-time range of concern. It was found that small adjustments to the current values in III-NH could be introduced but that the existing values were conservative and could be retained. The existing database was found to be adequate to extend the coverage to 600,000 hours for temperatures below 650 C (1200 F).

36 MATERIALS SCIENCE↗

GCR: Development of Improved Alloy 800H Weldment

In Section III, Division 5 of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code, Alloy 800H is qualified for elevated-temperature nuclear construction for temperatures up to 760°C (1400°F) and a maximum service life of 300,000 hours. There are two permissible filler metals for Alloy 800H weldments specified in Division 5: ENiCrFe-2 (Alloy A) and ERNiCr-3 (Alloy 82). Low creep-rupture strengths of these weldments at the upper limits of the qualified temperatures and service lives may restrict the design envelope for elevated-temperature nuclear construction with Alloy 800H. As a result, an alternative filler metal is desired to improve the creep-rupture strengths of Alloy 800H weldments for the qualified temperatures and service lives. This work investigates an overmatched filler metal. Specifically, a weldment with Alloy 800H base metal and Alloy 617 filler metal fabricated by semiautomated gas tungsten arc welding is investigated. A scoping creep-rupture test program was conducted of cross-weld specimens at temperatures ranging from 750 to 1000°C (1292 to 1832°F). Preliminary results on the creep-rupture strengths of the Alloy 800H weldment with an Alloy 617 filler metal do not show significant improvement compared to the filler metals currently qualified in Division 5 for Alloy 800H weldments. Consequently, work is in progress to investigate a matching filler metal, UTP A 2133 Mn.

36 MATERIALS SCIENCE↗

How far can a rubber molecule stretch before breaking? Ab initio study of tensile elasticity and failure in single-molecule polyisoprene

We present ab initio calculations of the internal C-C bond dissociation curve for single molecules of (cis 1,4) polyisoprene, polybutadiene, and polyethylene, all of comparable length. We define 'bond rupture' as that point on the reaction coordinate where the unrestricted Kohn-Sham, or diradical, solution falls below the restricted, or closed-shell, solution. Using this well-defined though crude approximation, we find that rupture occurs at a tensile force of 6.8 nN for poly isoprene and 7.2 nN for polybutadiene. Their respective rupture strains are 45% and 42%. Our calculations show that the energy density vs. extension is not sensitive to the length of the molecule, i.e., it is essentially independent of the number of isoprene units contained. These relatively large rupture strains have important implications for understanding the failure mechanism in rubber, and imply that purely enthalpic chain stretching must commence well before tensile failure occurs.

74 ATOMIC AND MOLECULAR PHYSICS↗

Large earthquake processes in the northern Vanuatu subduction zone

Abstract The northern Vanuatu (formerly New Hebrides) subduction zone (11°S to 14°S) has experienced large shallow thrust earthquakes with M w > 7 in 1966 ( M S 7.9, 7.3), 1980 ( M w 7.5, 7.7), 1997 ( M w 7.7), 2009 ( M w 7.7, 7.8, 7.4), and 2013 ( M w 8.0). We analyze seismic data from the latter four earthquake sequences to quantify the rupture processes of these large earthquakes. The 7 October 2009 earthquakes occurred in close spatial proximity over about 1 h in the same region as the July 1980 doublet. Both sequences activated widespread seismicity along the northern Vanuatu subduction zone. The focal mechanisms indicate interplate thrusting, but there are differences in waveforms that establish that the events are not exact repeats. With an epicenter near the 1980 and 2009 events, the 1997 earthquake appears to have been a shallow intraslab rupture below the megathrust, with strong southward directivity favoring a steeply dipping plane. Some triggered interplate thrusting events occurred as part of this sequence. The 1966 doublet ruptured north of the 1980 and 2009 events and also produced widespread aftershock activity. The 2013 earthquake rupture propagated southward from the northern corner of the trench with shallow slip that generated a substantial tsunami. The repeated occurrence of large earthquake doublets along the northern Vanuatu subduction zone is remarkable considering the doublets likely involved overlapping, yet different combinations of asperities. The frequent occurrence of large doublet events and rapid aftershock expansion in this region indicate the presence of small, irregularly spaced asperities along the plate interface.

Cleveland, K. Michael↗

Dynamic fault weakening and strengthening by gouge compaction and dilatancy in a fluid-saturated fault zone

Fault gouge deformation likely plays a significant role in controlling the strength of mature, large-displacement faults. Experiments show that intact gouge deforms in an overall ductile and stable manner, readily compacting, but dilates and experiences brittle failure under large strain rate. Inelastic gouge compaction and dilatancy are modeled here using a combined Mohr-Coulomb and end-cap yield criterion in a dynamic rupture model of a strike-slip fault with strongly velocity-weakening friction. We show that large shear stress concentration ahead of the rupture associated with the rupture front causes the gouge layer to compact (e.g., by structural collapse and comminution), leading to rapidly elevated pore pressure and significant weakening of the principal fault surface. Shortly after the rupture front passes, strong dilatancy during strength drop and rapid sliding reduces pore pressure and strengthens the fault, promoting slip pulses. Large strain localization in the gouge layer occurs as a result of rapid gouge dilatancy and strain softening. The combination of prerupture weakening from compaction and restrengthening from dilatancy hardening leads to a smaller-strength drop, and limits the stress concentration outside the gouge layer. Furthermore, this leads to a reduction of inelastic shear strain in the damage zone, which is more consistent with geological observations and high-speed frictional experiments. With the presence of well-developed fault gouge, the strength of mature faults may be limited by end-cap rather than Mohr-Coulomb failure; thus, their frictional strengths are significantly smaller than Byerlee friction.

58 GEOSCIENCES↗

Creep Behavior and Phase Equilibria in Model Precipitate Strengthened Alumina-Forming Austenitic Alloys

Abstract Creep-rupture behavior and microstructural response in alumina-forming austenitic (AFA) alloys with two different precipitation strengthening mechanisms, “Laves-phase + M 23 C 6 carbide” and “coherent L1 2 γ′-Ni 3 (Al,Ti),” were explored as “model” cases of multi-phase, multi-scale heat-resistant AFA alloys for 650–750°C use. These alloys will be used to guide and verify computational alloy design and life-prediction modeling under an on-going eXtremeMAT project through the Office of Fossil Energy and Carbon Management, US Department of Energy. Computational thermodynamics were used to design and predict the amounts of strengthening and deteriorating secondary phases at 750°C. Creep-rupture lives of the alloys tested at 750°C and 100 MPa were in a range of 4000–9000 h, and the microstructure at the gage/grip after creep-rupture testing was compared with isothermally aged alloys for 1500 h, as well as the calculated phases. Detailed microstructure characterization includes phase identification, volume fraction measurement, and compositional analysis, which were correlated with the creep-rupture properties. High-temperature oxidation resistance was also screened and compared with commercial, chromia-forming heat-resistant steels. These model alloys also provide the basis for further design and optimization of next generation AFA alloys with improved creep resistance.

36 MATERIALS SCIENCE↗