Results for “ROTORS” — Page 34

DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence R - Raw Data

Sequence R: Step AOA, No Probes (P) This sequence was designed to quantify the effect of the five-hole probes on the 3-D blade static angle-of-attack response in the presence of rotational influences by repeating Sequence K without five-hole probes. This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speeds ranged from 6 m/s to 20 m/s, and data were collected at yaw angles of 0° and 30°. The rotor rotated at 72 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read –99999.99. The blade pitch angle ramped continuously at 0.18°/s over a wide range of increasing and decreasing pitch angles. A step sequence was also performed. The blade pitch was stepped 5°; the flow was allowed to stabilize; and the pitch angle was held for 5 seconds. Then the pitch angle step was repeated. Again, a wide range of pitch angles was obtained, both increasing and decreasing. The file lengths for this sequence varied from 96 seconds to 6 minutes, depending on the pitch angle range. Some short points were collected at 0° yaw and 3° pitch to ascertain the functionality of the instrumentation and repeatability over time. The file name convention used the initial letter R, followed by two digits specifying wind speed, followed by two digits for yaw angle, followed by RU, RD, or ST, followed by the repetition digit. The angle of attack motion was differentiated by RU (ramp up), RD (ramp down), and ST (step down, then step up). This sequence is related to Sequences K and L.

17 WIND ENERGY↗

DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence S - Raw Data

Sequences S, T, and U: Upwind, No Probes (F); Upwind 2° Pitch (F); Upwind 4° Pitch (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of 0° to 180° were achieved for Sequence S, but the yaw angle remained at 0° for Sequences T and U. The blade tip pitch was 3° for Sequence S, 2° for Sequence T, and 4° for Sequence U. These three sequences were interleaved during testing because the pitch angle change was easily made by the turbine operator. The rotor rotated at 72 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to -99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. In addition to the standard 30-second campaigns, yaw sweeps were done at 7 m/s and 10 m/s for the Sequence S configuration. These 6-minute campaigns were collected while the yaw drive rotated the turbine 360° at a rate of 1°/s. The file names for these campaigns use the letter designation, followed by two digits for wind speed, followed by YSU, followed by 00.

17 WIND ENERGY↗

DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence T - Raw Data

Sequences S, T, and U: Upwind, No Probes (F); Upwind 2° Pitch (F); Upwind 4° Pitch (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of 0° to 180° were achieved for Sequence S, but the yaw angle remained at 0° for Sequences T and U. The blade tip pitch was 3° for Sequence S, 2° for Sequence T, and 4° for Sequence U. These three sequences were interleaved during testing because the pitch angle change was easily made by the turbine operator. The rotor rotated at 72 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to -99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. In addition to the standard 30-second campaigns, yaw sweeps were done at 7 m/s and 10 m/s for the Sequence S configuration. These 6-minute campaigns were collected while the yaw drive rotated the turbine 360° at a rate of 1°/s. The file names for these campaigns use the letter designation, followed by two digits for wind speed, followed by YSU, followed by 00.

17 WIND ENERGY↗

DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence U - Raw Data

Sequences S, T, and U: Upwind, No Probes (F); Upwind 2° Pitch (F); Upwind 4° Pitch (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of 0° to 180° were achieved for Sequence S, but the yaw angle remained at 0° for Sequences T and U. The blade tip pitch was 3° for Sequence S, 2° for Sequence T, and 4° for Sequence U. These three sequences were interleaved during testing because the pitch angle change was easily made by the turbine operator. The rotor rotated at 72 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to -99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. In addition to the standard 30-second campaigns, yaw sweeps were done at 7 m/s and 10 m/s for the Sequence S configuration. These 6-minute campaigns were collected while the yaw drive rotated the turbine 360° at a rate of 1°/s. The file names for these campaigns use the letter designation, followed by two digits for wind speed, followed by YSU, followed by 00.

17 WIND ENERGY↗

DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence V - Raw Data

Sequence V: Tip Plate (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 25 m/s, and the yaw angle was held at 0°. The blade pitch angle was 3°. The rotor rotated at 72 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. The standard tip blocks were replaced with a tip plate to simulate the effect of an undeployed tip-mounted aerodynamic brake as shown in Appendix A. Note that the blade radius was not changed during post-processing so the pressure tap locations are at the same radial location, but the reference to 30% represents 30% of 5.029 m, not 4.943 m. Throughout this report, references to the blade span are made for the 5.029- m radius, not the 4.943-m radius.

17 WIND ENERGY↗

DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence X - Raw Data

Sequence X: Elevated RPM (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 12 m/s, and yaw angles of ±30° were obtained. The blade pitch angle was 3°. The rotor rotated at 90 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. As described in Appendix F, the hydrostatic correction derived for operation at 72 RPM was applied to these data.

17 WIND ENERGY↗

DOE OSTI2022

Camera / Raw Data

The SUMR-D CART2 turbine data are recorded by the CART2 wind turbine's supervisory control and data acquisition (SCADA) system for the Advanced Research Projects Agency–Energy (ARPA-E) SUMR-D project located at the National Renewable Energy Laboratory (NREL) Flatirons Campus. For the project, the CART2 wind turbine was outfitted with a highly flexible rotor specifically designed and constructed for the project. More details about the project can be found here: https://sumrwind.com/. The data contain video data of the wind turbine blades during operation as well as while parked. Since the blades had a coning angle, the blades are only in frame of the video camera when the blades are in a pitched to run configuration.

17 WIND ENERGY↗

DOE OSTI2023

Wind Turbine / Reviewed Data

The SUMR-D CART2 turbine data are recorded by the CART2 wind turbine's supervisory control and data acquisition (SCADA) system for the Advanced Research Projects Agency–Energy (ARPA-E) SUMR-D project located at the National Renewable Energy Laboratory (NREL) Flatirons Campus. For the project, the CART2 wind turbine was outfitted with a highly flexible rotor specifically designed and constructed for the project. More details about the project can be found here: https://sumrwind.com/. The data include power, loads, and meteorological information from the turbine during startup, operation, and shutdown, and when it was parked and idle.

17 WIND ENERGY↗

DOE OSTI2026

OC6 Phase III: Validation of Wind Turbine Aerodynamic Loading During Surge/Pitch Motion

The objective of Phase III of the Offshore Code Comparison Collaboration, Continued, with Correlation and unCertainty (OC6) project was to validate the accuracy of aerodynamic load predictions by offshore wind modeling tools for a floating offshore wind turbine as it experiences large surge-translational and pitch-rotational motion, as would occur during normal operation. The test data considered were generated at Politecnico di Milano – a wind tunnel with a robotic excitation system to emulate wave loading on the wind turbine. Testing was performed using a scaled version of the DTU 10-MW reference model, and motion was prescribed as harmonic oscillations in the surge and pitch directions, independently. A variety of models were examined in the project, performing a three-way validation between engineering-level tools, higher-fidelity tools, and measurement data from two wind tunnel experimental campaigns. The Load Cases (LC) considered in this testing are as follows: LC 1.X - Steady Wind LC 2.X - Unsteady Wind - Surge Motion LC 3.X - Unsteady Wind - Pitch Motion Details on the results of the OC6 Phase III campaign can be found in the following reference: Bergua R., et al. OC6 project Phase III: validation of the aerodynamic loading on a wind turbine rotor undergoing large motion caused by a floating support structure, Wind Energ. Sci., 8, 465–485, https://doi.org/10.5194/wes-8-465-2023, 2023.

17 WIND ENERGY↗

DOE OSTI2025

Site E - Virtual Tower High-Frequency Wind Velocity / Derived Data

This dataset contains Dual-Doppler wind reconstruction from stare lidar scans two rotor diameters south of the King Plains G02 turbine. The line-of-sight velocity data can be found in sa5.lidar.z03.b0 and sa1.lidar.z03.b0. The reconstruction is done neglecting the contribution from vertical velocity.

17 WIND ENERGY↗

DOE OSTI2023

RAAW

High-fidelity wind turbine modeling advances necessitate model validation datasets of equally high fidelity. The Rotor Aerodynamics, Aeroelastics & Wake (RAAW) project was designed to address this need. This three-year project runs from October 2021 through October 2024 starting with a field data collection period followed by model validation activities. RAAW is a partnership between GE Renewable Energy and the United States Department of Energy (DOE) through the National Renewable Energy Laboratory (NREL) and Sandia National Laboratories. The field experiment is designed to make detailed measurements of the inflow, wind turbine response, and the resulting wake. The experimental dataset will be suitable for validating wind turbine models across the fidelity spectrum from actuator disk methods to blade-resolved codes.

17 WIND ENERGY↗

DOE OSTI2024

Spinning Hall Probe magnetic compass

In a large range of physics and space experiments, the direction of the magnetic field needs to be determined with an accuracy on the level of one milli radian or better. We have proposed a new type of magnetic compass - a rotation-based one, which provides an alternating signal from the Hall probe proportional to the value of the magnetic field transverse to the axis of rotation. The spinning Hall probe device has been realized. Alignment of the spinning axis for a minimum (zero) value of the signal allows us to find the direction of the magnetic field. The device does not require calibration and is free of any drift problems. The measurement of the rotation axis direction was accomplished by means of a laser and a flat mirror attached to the rotor. The constructed prototype achieved an accuracy for the magnetic field direction in the experiment with the polarized He-3 target on the level of one milli radian.

Wojtsekhowski, Bogdan↗

DOE OSTI2019

Contributing to Long-term Wind Resource Characterization through Buoy-based Observations of Meteorological and Oceanographic Conditions

The U.S. Department of Energy (DOE) supports development of renewable power generation within the U.S. with increasing emphasis on offshore wind energy. This development is currently impeded by a lack of long-term wind observations above the ocean surface at wind turbine rotor plane heights. Pacific Northwest National Laboratory (PNNL) procured two AXYS WindSentinelTM buoys on behalf of DOE to support offshore wind resource assessment. The buoys are available for loan to qualified users according to agency priorities. The Lidar Buoy Loan Program represents an opportunity for organizations with an interest in offshore wind energy to work together with DOE to provide valuable meteorological and oceanographic data to the offshore community that is needed for offshore wind resource characterization. The buoys have already begun to fill observational gaps in offshore winds during long-term deployments off the coasts of Virginia and New Jersey and are scheduled for deployment off the coast of California in 2020. This paper provides an overview of the Lidar Buoy Loan Program, along with highlights of previous deployments, a summary of the upgrades to the lidar systems, and a discussion of the planned activities related to the buoys and the Lidar Buoy Loan Program.

floating lidar, offshore wind energy, wind resourc↗

DOE OSTI2022

Accelerated Wind-Turbine Wake Recovery Through Actuation of the Tip-Vortex Instability

Advances in wind-plant control have often focused on more effectively balancing power between neighboring turbines. Wake steering is one such method that provides control-based improvements in a quasi-static way, but this does little to fundamentally change the wake recovery process, and thus, it has limited potential. This study investigates use of another control paradigm known as dynamic wake control (DWC) to excite the mutual inductance instability between adjacent tip-vortex structures, thereby accelerating the breakdown of the structures. The current work carries this approach beyond the hypothetical by applying the excitation via turbine control vectors that already exist on all modern wind turbines: blade pitch and rotor speed control. The investigation leverages a free-vortex wake method (FVWM) that allows a thorough exploration of relevant frequencies and amplitudes of harmonic forcing for each control vector (as well as the phase difference between the vectors for a tandem configuration) while still capturing the essential tip-vortex dynamics. The FVWM output feeds into a Fourier stability analysis working to pinpoint candidate DWC strategies suggesting fastest wake recovery. Near-wake length reductions of >80% are demonstrated, although without considering inflow turbulence. Analysis is provided to interpret these predictions considering the presence of turbulence in a real atmospheric inflow.

17 WIND ENERGY↗

DOE OSTI2023

Impact of Aerodynamic Modeling Assumptions on Flutter Speeds of Vertical-Axis Wind Turbines

Theodorsen’s unsteady aerodynamic theory has been used extensively in flutter speed prediction of wind turbine blades. In this study, three key assumptions of Theodorsen theory (thin airfoil, flat wake, and small angle of attack) have been revisited, and all three assumptions have been addressed in combination to obtain new lift and moment equations that are subsequently applied in flutter calculations for full-scale vertical-axis wind turbine (VAWT) rotors, not just of an individual airfoil or blade. Furthermore, edgewise aerodynamics terms are added to the lift and moment equations to include their effects on flutter speeds. The newly obtained equations were implemented in the OWENS (Offshore Wind ENergy Simulation) toolkit, which is an FEM (Finite Element Method)-based toolkit for aeroelastic analysis of VAWTs. The effect of modifying each of these assumptions has been studied for the flutter RPM prediction of three primary modes of flutter of VAWTs: propeller, butterfly, and tower modes. For the land-based case, the most change was observed for the flutter RPM of the propeller mode, with a maximum increase of 2.62% for the two-bladed UTD 5 MW VAWT case. For the floating offshore case, the primary flutter modes (tower and platform pitch) were not significantly affected.

Engineering↗

DOE OSTI2025

Effect of Surface Roughness on Dynamic Stall in Pitching Motion

Dynamic stall plays a critical role in determining the performance and stability of a wide range of fluid-dynamics systems in various engineering applications. This unsteady aerodynamic phenomenon is particularly significant for maneuvering aircraft wings, jet aircraft subjected to gust encounters, helicopter rotor blades, and wind turbine blades [1–3]. The prediction of the dynamic stall vortex (DSV) is challenging due to factors such as unsteady aerodynamics, three-dimensional (3-D) effects, turbulence and flow separation, incoming gust, and surface impact effects [4–6]. Hence, advanced computational techniques and modeling approaches in computational fluid dynamics (CFD) would be required to enhance the accuracy and reliability of DSV predictions in dynamic stall scenarios. In the past, Batther and Lee [7] employed delayed detached eddy simulations (DDES) to understand the flow physics associated with the onset of dynamic stall. Their approach demonstrated that DDES achieves results comparable to those obtained from large-eddy simulations at a reduced computational cost. In another study, Khalifa et al. [8] examined the 3-D aspects of dynamic stall on a NACA 0012 airfoil using DES solvers. In conclusion, the findings underlined the superiority of 3-D simulations over two-dimensional approaches, particularly in predicting the lift coefficient values and capturing dynamic stall stages more precisely.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2023

Toward the Advanced Manufacturing of Land-Based Wind Turbine Blades

The National Renewable Energy Laboratory and General Electric (GE) are partners within the Additive and Modular-Enabled Rotor Blades and Integrated Composites Assembly (AMERICA) project. AMERICA aims to develop advanced manufacturing solutions to reduce labor and cycle time while increasing recyclability of wind turbine blades. The project is funded by the U.S. Department of Energy's Advanced Manufacturing Office. This paper describes the techno-economic and life cycle analysis of the novel manufacturing process applied to the 15-meter long tip of the blade of a representative 3.4 MW land-based wind turbine. We establish a comparison to a standard manufacturing process, highlighting challenges and opportunities. Several uncertainties affect the analysis, but we highlight an opportunity space. With the current set of assumptions, the tip adopting advanced manufacturing is predicted to lower labor by 21%, cycle time by 39%, and total blade tip costs by 15% while simultaneously increasing production quality and adopting recyclable thermoplastic resin. A life cycle analysis returns comparable metrics for climate change impact and embodied energy between the two processes.

3D printing↗

DOE OSTI2024

Cellulose crystallinity index (CrI) of switchgrass measured by solid-state NMR

Here we present a curated dataset of switchgrass cellulose crystallinity index (CrI) measured using solid state nuclear magnetic resonance (NMR) spectroscopy. Seventy-two topline switchgrass lines grown in greenhouse were collected and ground to -20/+80 mesh. The switchgrass was then Soxhlet-extracted with toluene/ethanol for 24 h to remove extractives. The extractives-free switchgrass was holopulped by using peracetic acid at 5 g loading per g biomass and the solution consistency was adjusted to 5% with DI water. Holopulping was conducted at room temperature for 24 h with stirring. The obtained holocellulose was washed excessively with DI water and air-dried at room temperature for 24 h. The dried holocellulose was treated with hydrochloric acid (2.5 M) for 2 h to remove hemicellulose. The isolated cellulose was collected by filtration, rinsed with DI water, and used to analyze cellulose crystallinity by solid-state NMR. The NMR samples were prepared by packing the moisturized cellulose into 4-mm cylindrical Zirconia MAS rotors. Cross polarization/magic angle spinning (CP/MAS) NMR analysis of cellulose was carried out on a Bruker Avance III 400-MHz spectrometer operating at 100.59 MHz for 13C in a Bruker double-resonance MAS probe head at spinning speeds of 8 kHz. The CP/MAS experiments utilized a 5 ms (90°) proton pulse, 1.5 ms contact pulse, 4 s recycle delay and 4000 scans. The cellulose crystallinity index was determined from the areas of the cellulose crystalline C4 signal (δ 86-92 ppm) over the entire C4 regions (δ 79-92 ppm) in the NMR spectra.

Cellulose, crystallinity index, switchgrass, solid↗