Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pu”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Measurements of effective actinides neutron capture cross sections in a cadmium-filtered epithermal neutron spectrum

In this work, a total of 20 actinide samples were irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL): 233 U (1), 235 U (1), 236 U (1), 238 U (1), 237 Np (2), 239 Pu (1), 240 Pu (1), 242 Pu (2), 244 Pu (2), 241 Am (2), 243 Am (2), 244 Cm (2), and 248 Cm (2). The samples were loaded in a basket containing a 1.1-mm thick cadmium filter. The presence of the filter drastically changes the neutron spectrum in the samples and accentuates the reaction rates in the resonance region. Isotopic ratios were determined using Multi-Collector Inductively Coupled Plasma Mass Spectrometry (MC-ICP-MS) that allowed inferring effective capture cross sections. Detailed best-estimate MCNP models of the experiment using ENDF/B-VII.0 nuclear data were developed to calculate the effective neutron cross sections and, subsequently, compare them with the cross sections inferred from experimental results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Evidence of an oxidation induced phase transformation for a delta phase plutonium-gallium alloy

The oxidation of an ~1.5 at% Ga plutonium metal alloy in dry air as a function of time was studied using a combination of FIB-SEM, AES, and XRD. Analysis of SEM images of FIB cross-sections of the oxide allowed for direct measurement of the oxide thickness as well as determination of heterogeneity in the extent of the oxide. AES analysis performed on cross-sections of the oxide allowed for quantitative analysis of the atomic composition and semi-quantitative analysis of the chemical composition. Initial preparation of the sample was found to induce a martensitic transformation to α' - Pu with an average thickness of 233 nm. Electropolishing was found to be sufficient to fully remove the α' layer with creation of only a minimum oxide layer. Growth of the oxide in dry air was found to initially follow parabolic kinetics, with a parabolic rate constant orders of magnitude higher than expected for δ-Pu but in-line with values extrapolated to room temperature for α-Pu. Following complete oxidation of the initial α` layer, further regions of plutonium metal depleted in gallium were observed to form at the oxide / metal interface. However, gallium, as Ga 2 O 3 , was found to be enriched at the surface and present in the oxide in an amount comparable to the relative Ga:Pu ratio of the bulk metal alloy. Finally, the results presented here serve to bridge a diverse array of previous experimental and theoretical data and provide the first comprehensive view of the fate of the δ-stabilizer during formation of an oxide.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Measurement of PuO 2 film thickness by electron probe microanalysis (EPMA) calibration curve method

Plutonium (Pu) surfaces are highly reactive toward oxygen containing species and, therefore, invariably covered with oxides (e.g. PuO 2 ) during transport and handling. The actual thickness of the surface oxide may dictate if a plutonium part is suitable for a certain application. As a result, a cost-effective, quick, non-destructive, yet reliable means to measure the oxide layer thickness formed on Pu samples is desirable. In this study, the cross-sections of a series of room temperature grown oxides on Pu samples were trenched by focus ion beam (FIB) then observed by scanning electron microscopy (SEM) to measure the surface oxide thicknesses, which were then combined with the corresponding oxygen k-ratios provided by electron probe microanalysis (EPMA) to form calibration curves. Oxide thickness measurements for the calibration curves were made on samples within the typical SEM observable range for PuO 2 (35–400 nm). The portion of the calibration curve in the thinner oxide region (<35 nm) were approximated via Pouchou and Pichoir’s Φ(ρz) theory. Two specimens with micrometer-thick PuO 2 standards (one formed at room temperature and the other at higher temperature with a higher level of crystallinity) were made for the k-ratios in this study, allowing EPMA users to choose the standard that best suits their needs. If the surface corrosion is known to be PuO 2 (from the environment in which the Pu sample is stored) or if the stoichiometry of the surface oxide is confirmed by a preliminary/compliment technique, these calibration curves allow EPMA users to quickly and efficiently determine PuO 2 thicknesses from the measured oxygen k-ratios of their samples. The methodology presented in this study can also be used as a template for creating calibration curves for oxides grown on other actinides.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Raman and infrared spectra of plutonium (IV) oxalate and its thermal degradation products

For over 80 years, plutonium dioxide has been routinely produced via thermal decomposition of hydrated plutonium(IV) oxalate. Despite the longstanding utility of this process, the chemical structures of starting materials and intermediates produced during this thermal conversion remain ill-defined. To help resolve this uncertainty, we measured high-resolution Raman and infrared spectra of Pu(C 2 O 4 ) 2 ·6H 2 O that was heated to 25, 100, 220, 250, 350, and 450 °C in air. Our measurements show that Pu(C 2 O 4 ) 2 ·6H 2 O has a rich vibrational spectrum with at least 15 Raman bands between 180 cm -1 and 1900 cm -1 and 9 infrared bands between 800 cm -1 and 4000 cm -1 . As Pu(C 2 O 4 ) 2 ·6H 2 O is heated, water is liberated, and the oxalate ligand decomposes to produce plutonium oxycarbide species. When heated to 350 °C or higher, vibrational spectra are consistent with PuO 2 with some residual carbon-containing species. Full vibrational spectra, powder X-ray diffraction, and scanning electron microscopy measurements of Pu(C 2 O 4 ) 2 ·6H 2 O and its thermal degradation products are presented herein along with approximate assignments for observed spectral bands. These data can be used to validate and potentially improve existing computational models that describe the chemical structure of compounds produced during thermal degradation of plutonium (IV) oxalate. Given the utility of plutonium (IV) oxalate in synthesizing plutonium dioxide, these results are expected to provide value in the fields of nuclear fuel processing, nuclear nonproliferation, and nuclear forensics.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2023

Probing the thermal decomposition of plutonium (III) oxalate with IR and Raman spectroscopy, X-ray diffraction, and electron microscopy

The thermal decomposition of Pu(III) oxalate was analyzed by Raman microspectroscopy, infrared spectroscopy, scanning electron microscopy, and powder X-ray diffraction. These data show that crystalline Pu 2 (C 2 O 4 ) 3 •9H 2 O progressively loses water and oxalate ligands as it is heated, which leads to a decrease in long-range lattice ordering, though minimal changes are observed in gross crystalline morphology. The onset of PuO 2 formation was observed between 200 - 250 °C. Thermal decomposition of oxalate ligands leads to the formation of CO 2 and plutonium oxalate-carbonate moieties, which had not been observed in previously published thermogravimetric measurements of Pu(III) oxalate. Formation of plutonium oxalate-carbonate moieties is believed to be associated with a change in the plutonium oxidation state from 3+ to 4+, which occurs prior to PuO 2 formation. The data provided herein demonstrate the rich spectroscopic nature of a rather underexplored, and technologically relevant, plutonium system. Ideally these results will further future investigations into the Pu(III) oxalate system both experimentally and computationally.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural characterization of U-20Pu-10Zr-4Sb and U-20Pu-10Zr-4Sb-4Ln

Antimony is being investigated as a potential additive to metallic fuel to control fuel-cladding chemical interactions (FCCI). The most detrimental elements involved in FCCI are fission product lanthanides, leading to brittle intermetallics and low melting eutectic phases. Previous investigations of Sb as an additive focused on U-10Zr, in wt. %, as the fuel. The current investigation expands that to include Pu in the fuel. Here, two alloys, U-20Pu-10Zr-4Sb and U-20Pu-10Zr-4Sb-4Ln (wt. %, Ln=53Nd-25Ce-16Pr-6La) have been investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) to characterize the fuel as-cast microstructure and the microstructure after introduction of lanthanides. Sb reacts with Zr initially, forming Zr 2 Sb and Zr 5 Sb 3 , with as much as 20 at. % interstitial Pu present. In the presence of lanthanides, Sb forms Ln 4 Sb 3 with the lanthanides, containing ~14 at. % Pu. The Pu is substitutional for the lanthanides in the crystal lattice.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Nuclear Data Sheets for A=245

Available information pertaining to the nuclear structure of ground and excited states for all known nuclei with mass numbers A=245 have been compiled and evaluated. In this work, the adopted level and decay schemes, as well as the detailed nuclear properties and configuration assignments based on experimental data, are presented for these nuclides. When there are insufficient data, expected values from systematics of nuclear properties and/or theoretical calculations are utilized. Unexpected or discrepant experimental results are also noted. Since the last evaluation, new rotational bands in 245 Pu have been observed to high spin from transfer reaction 244 Pu( 209 Bi, 208 Biγ) by 2014Ho16. While in 245 Am, the 249 Bk α decay measurements by 2013Ah03 added a new rotational band based on π3/2[521] configuration. The 245 Pu β - decay scheme is basically what was proposed in the late 60's and 47 γ rays have still not been placed. In 245 Cm, precise alpha energies and intensities were measured by 2015Ah03 in 249Cf α decay. Their reported alpha energies of the main α group were about 2 keV lower than in the previous evaluation. The spin and parity of the g.s. of 245 Es is still ambiguous as more detailed information on the decay is needed. With the production of 249 No via fusion evaporation reaction by groups in Dubna and GSI, it's alpha decay was studied and some properties of the daughter 245 Fm were published and included in this evalaution. Information on the other nuclides is scarce and not much has been investigated since the last evaluation. A summary and compilation of the discovery of the various nuclides in this mass region is given in: 2013Fr02 ( 245 Pu, 245 Am, 245 Cm, 245 Bk, 245 Cf), 2011Me01 ( 245 Es), and 2013Th02 ( 245 Md, 245 Fm).

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Modeling of Am-241 as an alternative fuel source in a radioisotope thermoelectric generator

Radioisotope thermoelectric generators (RTGs) have been utilized in the USA to power satellites and space exploration equipment for over half a century. In our preceding paper, Dustin and Borrelli (2021), we assessed the performance of 241 Am as an alternative to 238 Pu by modeling the specific decay-heat and gamma spectra of several potential radioisotopes in SCALE-ORIGEN, and comparing these with 238 Pu An analysis of heat output, heat stability, safety, availability and required mass showed that of the isotopes reviewed, 241 Am had the greatest potential for replacing 238 Pu, with additional design considerations. In our current work, we have assessed radiation transport for two configurations of an 241 Am powered Multi-Mission Radioisotope Thermoelectric Generator (MMRTG), due to the potential health effects for operators, fabricators, and others with the potential to be exposed to neutrons and lower energy gamma rays. We have modeled the use of americium as a fuel source replacement for plutonium in current MMRTG designs. The assessment has been performed using MCNP6, in terms of neutron and gamma emissions that might interfere with sensitive equipment and power system production. The radiation transport behavior in terms of dose rate of the 241 Am fueled models is compared with that of a 238 Pu fueled model. Finally, additional work was performed to validate modeling simplifications with regards to thermocouple material configurations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Scanning tunneling spectroscopy of surface-oxidized Gallium-stabilized δ -phase plutonium

Here, the first contiguous experimental scanning tunneling spectroscopy (STS) measurements of the electronic structure of a plutonium (Pu) surface are presented and compared to current theoretical results. The experiments took place under UHV conditions, for which Pu is known to retain a native surface oxide. The STS data shows that no band gap is observable at room temperature. Theoretical calculations predict that bulk Pu oxides are semiconductors, but the spectral results for the cleaned Pu surface native oxide under UHV conditions could be better characterized as that of a semimetal.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Transport Modeling of Kinetically Limited Microscale Extraction Systems: Droplet and Supported Liquid Membrane Separations

Microfluidic droplet extraction devices can be used to efficiently measure solute phase transfer kinetics in liquid–liquid extraction systems. In this work, a droplet extraction apparatus was constructed using off-the-shelf and custom 3D printed parts for less than 110 USD. The interfacial kinetics of the transfer of Pu(IV) between an aqueous nitric acid phase and a 5 v/v% tridodecylamine (TDA) in toluene phase were characterized by determining the extent of Pu(IV) transfer between phases at different flow rates. Forward interfacial rate constants calculated from this data using an analytical model are 5.6 × 10 –3 mm s –1 under extraction (aqueous-to-organic solute transfer) conditions and 3.3 × 10 –3 mm s –1 under stripping (organic-to-aqueous solute transfer) conditions. The analytical model is valid when the rate of solute transfer across the interface between the two liquid phases has pseudo-first-order reversible reaction kinetics and is slow relative to the rate of solute transport to the interface. The change in the outlet concentration with residence time determined using the analytical model was compared with the results of a numerical model accounting for advection/diffusion to the interface in addition to kinetically limited interfacial solute transfer. These calculations revealed that for systems with forward interfacial rate constants greater than approximately 10 –2 mm s –1 , the analytical model must be supplemented with a numerical transport model accounting for an additional advection/diffusion mass transfer resistance. This threshold corresponds to a Damköhler number of one. The measured interfacial kinetic rate constants for Pu(IV)/TDA were used in a supported liquid membrane (SLM) numerical model, which showed that the Pu(IV) phase transfer kinetics are fast enough for use in a practical separation.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2024

Formation of Fully Stoichiometric, Oxidation-State Pure Neptunium and Plutonium Dioxides from Molecular Precursors

Amidate-based ligands (N-(tert-butyl)isobutyramide, ITA) bind κ 2 to form homoleptic, 8-coordinate complexes with tetravalent 237 Np (Np(ITA) 4 , 1-Np) and 242 Pu (Pu(ITA) 4 , 1-Pu). These compounds complete an isostructural series from Th, U–Pu and allow for the direct comparison between many of the early actinides with stable tetravalent oxidation states by nuclear magnetic resonance (NMR) spectroscopy and single crystal X-ray diffraction (SCXRD). The molecular precursors are subjected to controlled thermolysis under mild conditions with the exclusion of exogenous air and moisture, facilitating the removal of the volatile organic ligands and ligand byproducts. The preformed metal–oxygen bond in the precursor, as well as the metal oxidation state, are maintained through the decomposition, forming fully stoichiometric, oxidation-state pure NpO 2 and PuO 2 . Powder X-ray diffraction (PXRD), scanning transmission electron microscopy (STEM), and energy dispersive X-ray spectroscopy (EDS) elemental mapping supported the evaluation of these high-purity materials. This chemistry is applicable to a wide range of metals, including actinides, with accessible tetravalent oxidation states, and provides a consistent route to analytical standards of importance to the field of nuclear nonproliferation, forensics, and fundamental studies.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2021

Blending Polyurethane Thermosets Using Dynamic Urethane Exchange

Recycling crosslinked polyurethanes (PUs) is accomplished through mechanical or chemical processes that are energy-intensive or produce plastics of lesser value. Polymer recycling processes are notably intolerant of polymer mixtures, yet the ability to reprocess and compatibilize two or more crosslinked PUs together will make this process more amenable to mixed waste streams while offering an opportunity to tune the properties of the recycled polymer products. Here, we blend a rigid polyester PU and a soft polyether PU using twin-screw extrusion to yield materials with tunable mechanical properties based on the feed composition. Their material properties were compared to those of compression-molded reprocessed blends and blends where the monomers were mixed prior to synthesis. The extruded materials showed similar mechanical and thermal properties to newly prepared blends and had higher-value mechanical properties compared to the samples reprocessed via compression molding. The morphologies of the blends were observed using phase imaging via atomic force microscopy to show that there is less phase separation in the extruded materials compared to compression-molded blends. The mechanical properties of these materials were tunable from soft to elastomeric to rigid based on the feed composition, and this tunability was demonstrated through four consecutive reprocessing cycles, through which the mechanical properties were steadily varied from rigid to soft by incorporating increasing amounts of soft polyether PU material. Here, this blending method for reprocessing mixed waste compatibilizes different PUs and provides a means to tune the mechanical properties of a PU product, even if starting from waste streams of varying compositions. As such, this process represents an intriguing new approach for polymer reprocessing.

Extrusion↗
DOE OSTI2024

Renewable and Biodegradable Polyurethane Foams with Aliphatic Diisocyanates

The transition to renewable plastics will require the development of substitutes with existing industrial standards and manufacturing processes. Polyurethanes (PU), versatile plastics, are traditionally dominated by aromatic diisocyanates, which are challenging to derive from renewable sources. However, for higher biocontent, it is crucial to utilize aliphatic diisocyanates, which can be sourced from renewable plant or algae waste streams. Historically, PU foams relied on aromatic diisocyanates for essential hard segments, resulting in desired physical properties. Here, we report the generation of high-performance renewable and biodegradable PU foams utilizing aliphatic diisocyanates and aromatic polyols, translating hard segments into the polyester polyol component using biosourced furan dicarboxylic acid (FDCA) monomers. We demonstrate that an FDCA-based PU is suitable for foams with performance characteristics that meet commercial tolerances and can biodegrade under backyard compost conditions. Here, this demonstrates steps toward redesigning traditional petrochemical-based polymers to accommodate new biological monomers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Covalency of M–N Bonds in Isomorphous Lanthanide and Actinide 5-(2-Pyridyl)-1H-tetrazolate Complexes

Experimental and computational analyses of [M(pdtz) 3 (H 2 O) 3 ]·3.5H 2 O (M 3+ = Pu 3+ −Cm 3+ , La 3+ −Nd 3+ , and Sm 3+ −Ho 3+ , pdtz− = 5-(2-pyridyl)-1H-tetrazolate) were conducted to understand potential differences in bonding between lanthanide and actinide complexes with a N-donor ligand. Structural analyses show that the An−N bond distances in the Pu 3+ , Am 3+ , and Cm 3+ complexes are within error of one another. Whereas in the lanthanide series, there is a nearly linear decrease in the Ln−N bond lengths from La 3+ to Ho 3+ (excluding Pm 3+ ). The An−N bond lengths are ∼0.015 Å shorter than their similarly-sized lanthanide analogs, in agreement with computational results that suggest greater covalent character in these bonds versus those with lanthanides. QTAIM analysis indicates that the An−N orbital mixing remains essentially unchanged from Pu 3+ to Cm 3+ , consistent with the nearly identical An−N bond lengths. However, upon deconvolution of the NLMOs into orbital compositions, the metal orbital contributions to An−N bonding decreases slightly overall wherein the 6d involvement remains constant, 7s involvement slightly increases, and 5f participation decreases. The molecular orbital energy diagram indicates that energy degeneracy between the 5f metal and 2p ligand orbitals increases from Pu 3+ to Cm 3+ and counteracts the contraction of the 5f orbtials. Together with prior reports of decreasing energy degeneracy between 5f and 3p orbitals from Np 3+ to Cf 3+ , these observations provide guidance on understanding how chemical bonding evolves in the actinide series.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Modeling the impact of extreme weather events and future climate on the radiologically contaminated sites of Enewetak Atoll

Enewetak Atoll underwent 43 historical nuclear tests from 1948 to 1958, including the first hydrogen bomb test, resulting in a substantial nuclear material fallout contaminating the Atoll and the lagoon waters. The radionuclide fallout material deposited in lagoon sediments and land soil will remain for decades to come. With intensifying climate and extreme weather events, the possibility of redistribution of deposited radionuclide material has become a great concern. This study uses a numerical modeling approach to estimate the potential elevated radionuclide concentrations that can be distributed during storm events under current and future climates. We simulated three historical storm scenarios that are most likely to impact Atoll’s environment and remobilize the radionuclide-bound sediments. WRF-ARW was used to reconstruct these storm scenarios under current year (2015) and future year (2090) climates. Storm-induced ocean hydrodynamics conditions were generated using FVCOM. FVCOM-ICM was externally coupled to simulate the fate and transport of radionuclides. Given that the 239 Pu is the largest inventory of the lagoon and Atoll islands, the model results show the highest average 239 Pu concentration that an island may be exposed to is 3.25E-4 Bq/m 3 (becquerel per cubic meters), which is an increase of 84 times the average baseline/existing 239 Pu concentration without the storm conditions. The overall increase in 239 Pu average over all the islands of Atoll is about 20 folds relative to the baseline concentration. Despite the high relative increase ratios, the significantly low activity concentrations may not pose an immediate exposure risk. However, due to the limitations of the study and uncertainties/biases in the historical data used, further research supported by field surveys to better characterize the current contamination level may be needed to make more accurate predictions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

2.2.2-Cryptand complexes of neptunium(III) and plutonium(III)

New coordination environments are reported for Np(III) and Pu(III) based on pilot studies of U(III) in 2.2.2-cryptand (crypt). The U(III)-in-crypt complex, [U(crypt)I 2 ][I], obtained from the reaction between UI 3 and crypt, is treated with Me 3 SiOTf (OTf = O 3 SCF 3 ) in benzene to form the [U(crypt)(OTf) 2 ][OTf] complex. Similarly, the isomorphous Np(III) and Pu(III) complexes were obtained similarly starting from [AnI 3 (THF) 4 ]. All three complexes (1-An; An = U, Np, Pu) contain an encapsulated actinide in a THF-soluble complex. Finally, absorption spectroscopy and DFT calculations are consistent with 5f 3 U(III), 5f 4 Np(III), and 5f 5 Pu(III) electron configurations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Expanded Intercomparison of Nuclear Data Libraries Using Jupiter and Jupiter High-240 Experiments

There is a limited availability of plutonium experiments with sensitivity to lead in the ICSBEP (International Handbook of Evaluated Criticality Safety Benchmark Experiments) Handbook. The Jupiter and Jupiter High-240 experiments were performed at the National Criticality Experiments Research Center as a collaborative effort between Los Alamos National Laboratory and the Japan Atomic Energy Agency to assess lead void coefficients in a plutonium-lead system containing weapons- and reactor-grade plutonium, respectively. Concurrent with benchmark development, an intercomparison of calculations using different nuclear data libraries has been performed to assess the usability of the experimental data for nuclear data adjustment in a “softer-that-fast” neutron energy spectrum. Eigenvalue calculations using MCNP with the ENDF/B-VIII.0 and TENDL-2021 nuclear data libraries calculate closest to the benchmark values for Jupiter. Calculations using JENDL-5 and ENDF/B-VIII.1 match best with the Jupiter High-240 values. Lead void worth calculations using the various nuclear data libraries are all within 3σ of their respective measured values. Perturbation studies between ENDF/B-VIII.0 and ENDF/B-VIII.1 demonstrate an approximate increase in calculated eigenvalues for the Jupiter series experiments by ~240 pcm for plutonium (mostly 239 Pu) and ~120 pcm for lead accompanied by a decrease contributed by ~113 pcm for copper and ~13 pcm for stainless steel. Nuclear data sensitivities and uncertainties investigated using Whisper show slightly lower sensitivity to scatter than a lead-reflected plutonium sphere but greater sensitivity to neutron capture. The sensitivities between Jupiter and Jupiter High-240 for lead are very similar for both ENDF/B-VIII.0 and ENDF/B-VIII.1 nuclear data. These benchmarks are more sensitive to neutron capture in lead than other plutonium benchmark experiments and would be useful for both lead and 240 Pu validation. In conclusion, with the high degree of compensating effects between copper, lead, and plutonium cross sections, additional isolated Pb-Pu and Cu-Pu benchmarks would be beneficial in improving these nuclear data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Four-decade follow-up of a plutonium-contaminated puncture wound treated with Ca-DTPA

Contaminated wounds are a common route of internal deposition of radionuclides for nuclear and radiation workers. They may result in significant doses to radiosensitive organs and tissues in an exposed individual's body. The United States Transuranium and Uranium Registries' whole-body donor (Case 0303) accidentally punctured his finger on equipment contaminated with plutonium nitrate. The wound was surgically excised and medically treated with intravenous injections of Ca-DTPA. A total of 16 g Ca-DTPA was administered in 18 treatments during the 2 months following the accident. Ninety-three urine samples were collected and analysed over 14 years following the accident. An estimated 239 Pu activity of 73.7 Bq was excreted during Ca-DTPA treatment. Post-mortem radiochemical analysis of autopsy tissues indicated that 40 years post-accident 21.6 ± 0.2 Bq of 239 Pu was retained in the skeleton, 12.2 ± 0.3 Bq in the liver, and 3.7 ± 0.1 Bq in other soft tissues; 1.35 ± 0.02 Bq of 239 Pu was measured in tissue samples from the wound site. To estimate the plutonium intake, late urine measurements, which were unaffected by chelation, and post-mortem radiochemical analysis results were evaluated using the IMBA Professional Plus software. The application of the National Council on Radiation Protection and Measurements wound model with an assumption of intake material as a predominantly strongly retained soluble plutonium compound with a small insoluble fraction adequately described the data (p = 0.46). The effective intake was estimated to be 50.2 Bq of plutonium nitrate and 1.5 Bq of the fragment. Here, the prompt medical intervention with contaminated tissue excision and subsequent Ca-DTPA decorporation therapy reduced 239 Pu activity available for uptake and long-term retention in this individual's systemic organs by a factor of 38.

239Pu↗