Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pressure Core”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

New technique for the direct measurement of core noise from aircraft engines

The core noise levels from gas turbine aircraft engines were measured using a technique which requires that fluctuating pressures be measured in the far field and at two locations within the engine core. The cross spectra of these measurements are used to determine the levels of the far-field noise that propagated from the engine vore. The technique makes it possible to measure core noise levels even when other noise sources dominate. The technique was applied to signals measured from an Avco Lycoming YF102 turbofan engine. Core noise levels as a function of frequency and radiation angle were measured and are presented over a range of power settings.

Krejsa, E. A.↗
NASA NTRS2003

Facesheet Delamination of Composite Sandwich Materials at Cryogenic Temperatures

The next generation of space transportation vehicles will require advances in lightweight structural materials and related design concepts to meet the increased demands on performance. One potential source for significant structural weight reduction is the replacement of traditional metallic cryogenic fuel tanks with new designs for polymeric matrix composite tanks. These new tank designs may take the form of thin-walled sandwich constructed with lightweight core and composite facesheets. Life-time durability requirements imply the materials must safely carry pressure loads, external structural loads, resist leakage and operate over an extremely wide temperature range. Aside from catastrophic events like tank wall penetration, one of the most likely scenarios for failure of a tank wall of sandwich construction is the permeation of cryogenic fluid into the sandwich core and the subsequent delamination of the sandwich facesheet due to the build-up of excessive internal pressure. The research presented in this paper was undertaken to help understand this specific problem of core to facesheet delamination in cryogenic environments and relate this data to basic mechanical properties. The experimental results presented herein provide data on the strain energy release rate (toughness) of the interface between the facesheet and the core of a composite sandwich subjected to simulated internal pressure. A unique test apparatus and associated test methods are described and the results are presented to highlight the effects of cryogenic temperature on the measured material properties.

Gates, Thomas S.↗
DOE OSTI2021

On the very high energy confinement observed in super H-mode DIII-D experiments

Analysis of recent super H-mode experiments on DIII-D shows that high rotation, not high pedestal, plays the essential role in achieving very high confinement H98y2 > 1.5. Very high confinement is reached early on in the H-mode phase of these discharges, when the pedestal is still very low, but after the toroidal rotation has already built-up to very high levels in the core. As the discharge evolves, the rotation drops, and so does the energy confinement, despite a sustained very high pressure pedestal. During this evolution, the confinement quality is linearly correlated with the core toroidal rotation, which varies according to different levels of injected neutral beam torque per particle. Core transport modeling shows that the contribution from rotation in the E×B shear is responsible for confinement quality significantly in excess of standard H-mode (H98y2 ∼ 1).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

The Effect of Pressure on NO x Entitlement and Reaction Timescales in a Premixed Axial Jet-In-Crossflow

This paper investigates the pressure dependency of a lean premixed jet injected into a lean vitiated crossflow with an experimentally verified detailed chemistry computational fluid dynamics (CFD) model and 53 species considered. Experimental data were taken in an axially staged combustor with an optically accessible test section, allowing the use of particle image velocimetry (PIV) and CH* chemiluminescence techniques as well as point measurement of species concentration, temperature, and pressure. The experimental data cases at one, three, and five atmospheres were selected to describe the flame stabilization dependency on pressure and gain the required knowledge for an extrapolation to engine condition. Simulated exit nitrogen oxide levels were validated with experimental emission data, and a global emission trend for the NO reduction at elevated pressure and constant turbine inlet temperature level was defined. The nitrogen oxide benefit at elevated operating pressure was justified with the significantly smaller flame surface area: the analysis of the simulated spanwise and top-view profiles showed a relatively short receded core flame with nitrogen oxide production in the center at high pressure relative to a longer and larger shear layer flame at atmospheric condition that produced NO toward the inner and outer side of the flame. Furthermore, decomposition of the Damköhler number revealed the strong influence of the reaction timescales with higher reaction rates at elevated pressure, along with a moderate influence of the turbulent timescales, showing higher turbulence intensity in the lee-side recirculation zone at lower pressure.

03 NATURAL GAS↗
DOE OSTI2023

Multi-Physics System-level Simulations of a Generic Pebble Bed High-Temperature Gas Cooled Reactor with Coupled SAM/Griffin Model

A SAM model for a 200 MWth generic pebble bed high-temperature gas-cooled reactor (PBHTGR) is presented in this work. As an extension to the modeling effort from FY-22 (Ooi et al. (2022)), an improved core channel approach is used to model the pebble bed of the reactor. The improvement greatly simplifies the model and reduces the run time of the model. Furthermore, the SAM model is coupled to the Griffin reactor physics model from Stewart et al. (2021) using the MOOSE MultiApp system where neutronics calculations are performed by the Griffin model and thermal hydraulics calculations by the SAM model. Favorable predictions are produced by the SAM/Griffin coupled model for steady-state normal operating condition. A load-following transient is also simulated with the coupled model where the neutronics and thermal hydraulics responses of the core are predicted correctly by the model. A protected Pressurized Loss of Forced Cooling (PLOFC) accident is simulated with the SAM model, in which the reactor power is determined using the decay heat curve, and therefore the Griffin model is not needed and thus decoupled. A simplified RCCS (Reactor Cavity Cooling System) loop is added to the model to remove decay heat from the core during the transient. Qualitatively, the prediction by the SAM model matches the expected behavior of a PB-HTGR during a PLOFC accident.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Preliminary design analysis workflow for Division 5 HHA-3200 requirements for graphite core components

This report presents a design analysis workflow for graphite core components and assemblies, based on the design rules of ASME Boiler Pressure and Vessel Code, Section III, Division 5, Article HHA-3000. The workflow contains three stages: developing the design of the graphite core component, modeling the component with the finite element software MOOSE, and assessing if the component passes/fails the criteria of the HHA-3000 design rules. Since the design rules use probabilistic metrics specifically established to evaluate brittle materials, we developed a python library that performs all the statistical calculations necessary for the evaluations of the HHA-3000 criteria.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1993

Experimental investigation of vortex-fin interaction

An experimental investigation has been conducted to examine the mechanisms of vortex-fin interaction on a twin-fin configuration. The investigation included a parametric study of the effect of tail location. The vortices were generated by a 76 deg sharp-edged delta wing with vertical tails mounted behind the wing. The model included both a dynamically-scaled flexible tail and a pressure instrumented rigid tail. Surface oil-flow patterns, off-body laser light sheet visualizations, aerodynamic load measurements, mean and unsteady flexible tail response, and unsteady tail surface pressure measurements were obtained. The results show that the tail location did not affect the upstream trajectory of the delta wing vortex. The tail location did affect the location of vortex breakdown, the global structure of the flow field, the aerodynamic loads, and the fin buffeting levels. The buffeting levels were reduced as the fins were moved laterally toward the vortex core trajectory. Two distinct peaks were observed in the pressure excitation spectra in the post-breakdown flow. Finally, the presence of the flexible tail opposite the rigid pressure tail altered the pressure measurements at one angle of attack.

Washburn, Anthony E.↗
DOE OSTI2020

On the very high energy confinement observed in super H-mode DIII-D experiments

Analysis of recent super H-mode experiments on DIII-D shows that high rotation, not high pedestal, plays the essential role in achieving very high confinement H 98y2 >1.5. Very high confinement is reached early on in the H-mode phase of these discharges, when the pedestal is still very low, but after the toroidal rotation has already built-up to very high levels in the core. As the discharge evolves, the rotation drops, and so does the energy confinement, despite a sustained very high-pressure pedestal. During this evolution, the confinement quality is linearly correlated with the core toroidal rotation, which varies according to different levels of injected neutral beam torque per particle. Core transport modeling shows that the contribution from rotation in the E×B shear is responsible for confinement quality significantly in excess of standard H-mode (H 98y2 ~1).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Hydrogen solubility in FeSi alloy phases at high pressures and temperatures

Abstract Light elements alloying with metallic Fe can change the properties and therefore play a key role in the structure and dynamics of planetary cores. Hydrogen and silicon are possible light elements in the rocky planets’ cores. However, hydrogen storage in Fe-Si alloy systems remains unclear at high pressures and high temperatures because of experimental difficulties. Taking advantage of pulsed laser heating combined with high-energy synchrotron X-ray diffraction, we studied reactions between FeSi and H in laser-heated diamond-anvil cells (LHDACs) up to 61.9 GPa and 3500 K. We found that under H-saturated conditions the amount of H alloying with FeSi (0.3 and <0.1 wt% for the B20 and B2 structures, respectively) is much smaller than that in pure Fe metal (>1.8 wt%). Our experiments also suggest that H remains in the crystal structure of FeSi alloy when recovered to 1 bar. Further density functional theory (DFT) calculations indicate that the low-H solubility likely results from the highly distorted interstitial sites in the B20 and B2 structures, which are not favorable for H incorporation. The recovery of H in the B20 FeSi crystal structure at ambient conditions could open up possibilities to understand geochemical behaviors of H during core formation in future experiments. The low-H content in FeSi alloys suggests that if a planetary core is Si-rich, Si can limit the ingassing of H into the Fe-rich core.

Geochemistry & Geophysics↗
DOE OSTI2022

Argon metastable density and temperature of a 43 GHz microplasma

Argon (1s 5 ) metastable density and translational gas temperature are experimentally measured using laser diode absorption spectroscopy within a 43 GHz microplasma. The plasma is initiated and sustained within a photonic crystal constructed from a rectangular array of alumina rods, each 1 mm in diameter. This configuration generates stable microplasma from 10 to 600 Torr using millimeter wave power from 100 to 1200 mW. The metastable density is in the order of 10 18 m –3 at low pressure. However, Ar(1s 5 ) density decreases to undetectable levels with increasing pressure and wave power. The gas temperature is extracted from the Lorentzian line shape of the absorption profile at 811.53 nm. The gas temperature increases from approximately 400 K at low pressure to 2000 K at 320 Torr (427 mbar, 4.27 × 10 4 Pa). Furthermore, these data are compared with previous results and suggest that the microplasma has a dense core of electrons that depletes the metastable density at high gas pressure and wave power.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Identifying High-Performance Metal–Organic Frameworks for Low-Temperature Oxygen Recovery from Helium by Computational Screening

Metal–organic frameworks (MOFs) are an important class of porous crystalline materials for applications ranging from gas adsorption and separation to catalysis. There are thousands of potential MOFs available for separation applications. Here, we developed a computational approach to screen MOFs for the separation of oxygen–helium mixtures at low temperatures (100–200 K), conditions that were motivated by issues associated with propulsion in space-based settings. We used detailed molecular simulations for a small number of MOFs to develop screening methods that were then used to estimate the optimum temperatures for separations using pressure swing adsorption for 2932 MOFs from the CoRE MOF database and the swing capacity and oxygen–helium selectivity at these temperatures. We used the stability of the best-performing structures in the presence of moisture as a means to provide a short list of high-performance materials. In addition to identifying specific materials for oxygen–helium separations, this approach could prove useful for selecting adsorbents for other gas separations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Network stability of FKM rubber compounds under hydrogen pressure

Fluorocarbon-based rubber (FKM) compounds are typically utilized in the aeronautical industry due to its exceptional chemical and thermal resistance and recently has drawn significant interest from the hydrogen community for various hydrogen applications, but there exists little data evaluating its hydrogen compatibility. In this paper, a formulated FKM compound was exposed to ultrahigh hydrogen pressure (90 MPa) and analyzed by attenuated total reflectance Fourier-transform infrared (ATR-FTIR) spectroscopy and crosslinking densities by solvent swelling measurement. ATR-FTIR spectroscopic data demonstrated that high-pressure hydrogen not only caused cleavages in polymer backbone and cross linkages, but also induced additional degradation of FKM compounds by breaking intermolecular hydrogen bonding between carboxylic acids, which were produced during rubber molding and post curing processes. This hydrogen pressure-driven degradation was significantly higher towards the core of the material than at the surface due to its weaker bonding between polymers and fillers.

Polymers, hydrogen, stability, degradation, Charac↗
DOE OSTI2022

Design of a Compact Dry Cooler With an Aluminum Heat Exchanger Core for a Supercritical CO2 Power Cycle Is Evaluated for a Concentrating Solar Power Application

Abstract As the supercritical CO2 power cycle develops and the component technologies mature, there is still a need to reduce the associated capital and operating costs to maintain a competitive levelized cost of electricity (LCOE) in order to enter the market. When considering concentrating solar power (CSP) coupled with an sCO2 power block and sensible thermal storage, the technology presents a clean source for utility-scale power generation to support baseload or peak-load electrical demand. However, the LCOE of the technology is still considered higher than the competing technologies and should be reduced to better compete in the market; 2030 targets for dispatchable solar plants are 5¢/kWh for baseload CSP and 10¢/kWh for peaker plants, as set by the United States Department of Energy. In response to this need, this study is targeting improvements in the power cycle precooler to reduce power block contribution to LCOE. This study considers a dry cooler, as CSP plants are sensitive to water consumption because many installations are slated for remote or arid locations where solar irradiance is very high, but water is scarce. Furthermore, the power block footprint for an sCO2 system is quite compact, especially as compared to a steam cycle. Therefore, there is interest in installing a more compact dry cooler that is proportional to the reduced footprint sCO2 power block, while conventional dry coolers are an order of magnitude larger. The competing goals of size, performance, and cost were considered in this study to develop a compact dry cooler that can easily be packaged with the power block, significantly reducing the installation and transport cost compared to the current state of the art, while maintaining or improving upon the heat transfer performance and impact on plant LCOE. This paper details the high-level findings of a large dry cooler sensitivity study for design point selection, design of the compact dry cooler, expected year-round performance for the dry cooler and the power cycle, and the predicted LCOE for a 30-year plant life. It was found that an aluminum heat exchanger core can be suitably designed to meet the pressure and temperature requirements for a precooler in an sCO2 recompression Brayton cycle. The dry cooler assembly was found to have improved heat transfer performance, allowing for increased cycle efficiencies and a reduced plant LCOE. When coupled with a centrifugal blower and compact transition duct, the dry cooler assembly was able to reduce the installation footprint by over 50%.

14 SOLAR ENERGY↗
DOE OSTI2024

Differential Organic Carbon Mineralization Responses to Soil Moisture in Three Different Soil Orders Under Mixed Forested System: Supporting Data

This data contains data from 90-day long incubation study which aimed to look at the soil moisture-texture relationship on soil organic carbon (SOC) cycling. Soils were collected from three distinct soil textures from mixed forests in 2017: sandy (Georgia, 2017-05-01), loamy (Missouri, 2017-06-14) and clayey (Texas, December 2017) were incubated at different soil moisture levels (air-dried, 25% water holding capacity (WHC), 50% WHC, 100% WHC and 175% WHC) at room temperature for a period of 90 days. Files contain microbial respiration, active and slow SOC pools, and their respective mineralization rates, extractable organic carbon (C), and C-acquiring extracellular enzymes. Findings from these data were used in Singh et al. (2021). This study aimed to examine the interactive effect of soil moisture and texture on SOC mineralization. Soil samples of three distinct textures (sandy, loamy, and clayey) were collected from mixed forests of Georgia, Missouri, and Texas, respectively. Soil cores of 5 cm diameter were collected from numerous random locations at each site from 0-15 cm depth after scraping the litter layer and mixed thoroughly to obtain a composite sample per site. Three additional soil cores were collected to determine the WHC using pressure plate extractors. Soil samples were composited, and triplicate soil samples were incubated in mason jars for a period of 90 days at room temperature under different moisture regimes: air dried, 25% WHC, 50% WHC, at WHC and 100% saturation. Soil respiration was measured weekly, and destructive sampling was conducted at 1, 15, 60, and 90 days to determine extractable organic C, C acquiring enzyme activity, and active and slow SOC pools with their respective mineralization rates. The C acquiring enzyme activity was the total activity of α-glucosidase, β-glucosidase, cellobiohydrolase, and β-xylosidase enzymes. Gas samples for microbial respiration measurements were collected from headspace of incubation jars through the sampling ports on the lids and then analyzed using a Shimadzu Gas Chromatograph (GC-2014). Prior to sampling, the vials were evacuated. Blank correction was also done by collecting gas samples from empty incubation jars. Double pool exponential decay model was used in SigmaPlot to determine the active and slow SOC pools and their mineralization rates (Farrar et al., 2012; Jagadamma et al., 2014). The C-acquiring extracellular enzymes were measured using the microplate method by German et al., (2011). Microbial community structure was determined using the phospholipid fatty acid (PLFA) and neutral lipid fatty acid (NLFA) analyses (Buyer and Sasser, 2012). This dataset has seven data files provided in comma-separate (*.csv) format. Additional metadata are provided: seven data dictionaries and a file-level metadata file in comma separate (*.csv) format and a user guide in PDF (*.pdf) format.

Carbon acquiring enzyme activity↗
NASA NTRS1966

Models of the Earth's magnetic field.

Geomagnetic field model based on definition of core field, crustal field, ionospheric currents and plasma pressures, examining trapped particle behavior

GEOMAGNETIC FIELD↗
NASA NTRS1976

Methods for testing high voltage connectors in vacuum, measurements of thermal stresses in encapsulated assemblies, and measurement of dielectric strength of electrodes in encapsulants versus radius of curvature

Internal embedment stress measurements were performed, using tiny ferrite core transformers, whose voltage output was calibrated versus pressure by the manufacturer. Comparative internal strain measurements were made by attaching conventional strain gages to the same type of resistors and encapsulating these in various potting compounds. Both types of determinations were carried out while temperature cycling from 77 C to -50 C.

Bever, R. S.↗
NASA NTRS1979

Coannular supersonic ejector nozzles

The nozzles described exhibit a flow field which is supersonic except for the initial flow region, and the secondary mass flow is typically about five percent of the primary core flow. The features to improve the accuracy of the performance calculations are discussed. A special calculation is made to get as realistic a sonic line as possible for this geometry, using an analysis developed by Brown. The mixing between the secondary and core flows is treated to account for entrainment of the secondary flow into core. Both of these phenomena directly affect the pressure distribution on the shroud and therefore, the thrust that the nozzle produces. The importance of using a realistic sonic line and a mixing analysis is stressed.

Bishop, A. R.↗