Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Polymer morphology”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Blending Polyurethane Thermosets Using Dynamic Urethane Exchange

Recycling crosslinked polyurethanes (PUs) is accomplished through mechanical or chemical processes that are energy-intensive or produce plastics of lesser value. Polymer recycling processes are notably intolerant of polymer mixtures, yet the ability to reprocess and compatibilize two or more crosslinked PUs together will make this process more amenable to mixed waste streams while offering an opportunity to tune the properties of the recycled polymer products. Here, we blend a rigid polyester PU and a soft polyether PU using twin-screw extrusion to yield materials with tunable mechanical properties based on the feed composition. Their material properties were compared to those of compression-molded reprocessed blends and blends where the monomers were mixed prior to synthesis. The extruded materials showed similar mechanical and thermal properties to newly prepared blends and had higher-value mechanical properties compared to the samples reprocessed via compression molding. The morphologies of the blends were observed using phase imaging via atomic force microscopy to show that there is less phase separation in the extruded materials compared to compression-molded blends. The mechanical properties of these materials were tunable from soft to elastomeric to rigid based on the feed composition, and this tunability was demonstrated through four consecutive reprocessing cycles, through which the mechanical properties were steadily varied from rigid to soft by incorporating increasing amounts of soft polyether PU material. Here, this blending method for reprocessing mixed waste compatibilizes different PUs and provides a means to tune the mechanical properties of a PU product, even if starting from waste streams of varying compositions. As such, this process represents an intriguing new approach for polymer reprocessing.

Extrusion↗
NASA NTRS1989

A petrographic thin sectioning technique for evaluating composite materials

Petrographic thin sectioning by a low-speed diamond saw has been used in conjunction with transmission polarized light microscopy for the characterization of the microstructure and deformation mechanisms of a variety of polymer systems. It has proven possible by these means to study three types of thermoplastic matrices for composite applications: PEEK, BPA-based polycarbonate (PC), and a rubber-modified PC. The reinforcing fibers for these matrices were in all cases AS4 carbon fibers, unidirectionally arrayed. Superior analyzability of matrix morphology and subsurface fracture processes is achieved by thin sectioning.

Parker, D. S.↗
DOE OSTI2025

Characterization of the degradation of gamma-irradiated elastomers using Raman spectroscopy

This report presents key findings from Raman spectroscopic analysis of gamma-irradiated rubber samples extracted from a laminated lead-damped rubber (LDR) seismic isolation device. The samples were exposed to gamma radiation from a 60Co source in a Foss Therapy Services gamma irradiator, reaching absorbed doses up to 1600 kGy. A distinct threshold near 400 kGy was identified, beyond which significant spectral changes were observed. Two Raman peaks - at approximately 425 cm-1 and 2440 cm-1 - were tracked as a function of dose using Gaussian fitting. The 425 cm-1 peak, attributed to sulfur–sulfur (S–S) bond stretching (resulting from vulcanization of the rubber), exhibited a dose-dependent upshift, indicating radiation-induced crosslinking within the sulfur-based polymer network. Conversely, the 2440 cm-1 peak, likely associated with vibrational modes of additives or impurities, showed a downward shift with increasing dose, suggesting chain scission and degradation of non-rubber constituents. These results provide first-of-a-kind insights into the microstructural evolution of elastomers under high-dose gamma irradiation and establish a preliminary dose threshold for significant degradation. Future work will incorporate multi-modal characterization—including Fourier Transform Infrared (FTIR) spectroscopy, scanning electrom microscopy (SEM) of the rubber surface morphology, thermogravimetric analysis (TGA) to determine changes in thermal stability, and mechanical testing—to correlate molecular-level changes with macroscopic performance of these elastomers as damping media in seismic isolation devices. These findings are expected to provide regulatory guidance and design criteria for qualifying low-damping rubber seismic isolators in advanced nuclear reactor applications.

36 - MATERIALS SCIENCE↗
DOE OSTI2020

H-Mat Hydrogen Compatibility of Polymers and Elastomers

The H2@Scale program of the U.S. Department of Energy (DOE) Fuel Cell Technologies Office is supporting work on the hydrogen compatibility of polymers to improve the durability and reliability of materials for hydrogen infrastructure. The hydrogen compatibility program (H-Mat) seeks “to address the challenges of hydrogen degradation by elucidating the mechanisms of hydrogen-materials interactions with the goal of providing science-based strategies to design materials, (micro)structures, and morphology with improved resistance to hydrogen degradation.” This research has observed interactions of hydrogen and pressure with model rubber-material compounds resulting in volume change and compression-set differences in the materials. The materials were investigated using helium-ion microscopy (HeIM), which revealed significant morphological changes in the plasticizer-incorporating compounds after exposure, as evidenced by time-of-flight secondary ion mass spectrometry. Additional studies using transmission electron microscopy and nuclear magnetic resonance were performed to correlate morphological change to potential chemical change in the materials.

08 HYDROGEN↗
DOE OSTI2020

Influence of Coating Method on the Performance of Roll-to-Roll Coated PEM Fuel Cell Catalyst Layers

As production of fuel cell vehicles and power systems increases there is a need to understand the process science of fuel cell manufacturing. Industrial production of polymer electrolyte membrane fuel cell (PEMFC) electrodes will rely on continuous roll-to-roll (R2R) coating methods to meet the rates needed for mass production. There are a variety of coating methods that could be used to coat catalyst layers. The different physics of each method may result in different morphologies and performance. Here we present the results of a study comparing fuel cell catalyst layers coated using two R2R coating methods: slot-die and gravure. These two methods were selected because the physics of applying the liquid to the substrate is very different between the two cases. Pt/C catalysts layers were coated directly onto carbon-fiber gas diffusion media to create gas diffusion electrodes (GDEs), without the use of a decal transfer process. These GDEs were assembled into membrane electrode assemblies (MEAs) by hot pressing to Nafion membranes. In situ performance and other electrochemical diagnostics were used to determine the influence of coating method on catalyst layer electrochemical properties. Electron microscopy was utilized to understand the influence of coating method on electrode morphology and its influence on electrochemical properties. We also explored the influence of solvent ratio to understand the potential coupling between ink formulation and coating methodology.

DIRECT ENERGY CONVERSION,MATERIALS SCIENCE↗
NASA NTRS1977

Ion-beam-sputter modification of the surface morphology of biological implants

The surface chemistry and texture of materials used for biological implants may significantly influence their performance and biocompatibility. Recent interest in the microscopic control of implant surface texture has led to the evaluation of ion-beam sputtering as a potentially useful surface roughening technique. Ion sources, similar to electron-bombardment ion thrusters designed for propulsive applications, are used to roughen the surfaces of various biocompatible alloys or polymer materials. These materials are typically used for dental implants, orthopedic prostheses, vascular prostheses, and artificial heart components. Masking techniques and resulting surface textures are described along with progress concerning evaluation of the biological response to the ion-beam-sputtered surfaces.

Weigand, A. J.↗
DOE OSTI2025

Giant Electrostriction via Nanodomain Engineering in Relaxor Ferroelectric Polymers

Relaxor ferroelectric (RFE) polymers hold great promise for artificial muscles due to their high actuation strain, high loading stress, and fast response. However, the structural origin underlying their large electrostrictive deformation remains elusive. In this study, we investigate poly(vinylidene fluoride-co-trifluoroethylene) [P(VDF-TrFE)]-based RFE terpolymers, incorporating 1,1-chlorofluoroethylene (CFE) or chlorotrifluoroethylene (CTFE) (the terpolymers are denoted as terP-CFE and terP-CTFE, respectively) as termonomers. Although both terpolymers show similar semicrystalline morphology, drastically different electrostrictive properties are observed. Specifically, the terP-CFE annealed at 100 °C achieves a record-high transverse strain of ∼10.6%, whereas 100 °C-annealed terP-CTFE only shows a much lower actuation strain of ∼4.2% at the same poling field of 190 MV/m. To elucidate the origin of this difference, time-resolved wide-angle X-ray diffraction, small-angle X-ray scattering, and Fourier transform infrared experiments are performed during in situ electric poling. An RFE-to-ferroelectric (FE) crystal phase transition is observed for terP-CFE but is absent for terP-CTFE. Beyond the contribution of the crystalline phase, the oriented amorphous fraction and crystalline defects (e.g., taut-tie molecules) also play significant roles in enhancing electrostriction. In conclusion, this mechanistic insight provides a valuable foundation for the rational design of next-generation RFE polymers with tunable properties through defect engineering of their semicrystalline structures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Diazirine-based photo-crosslinkers for defect free fabrication of solution processed organic light-emitting diodes

The fabrication of solution deposited OLEDs is fraught with difficulties, largely due to the interlayer mixing and surface erosion during sequential deposition of the layers. We demonstrate that these problems can be circumvented by using photopolymerizable diazirine-based cross-linker capable of converting soluble organic materials into highly cross-linked insoluble networks. 3-Trifluoromethyl(aryl)diazirines photolyze readily upon the 10–15 min exposure of 365 nm UV irradiation to generate carbenes, which react with polymers or small molecules via C–H bond insertion producing highly cross-linked materials. This photo-generated cross-linking does not require any catalyst, initiator or short-wavelength UV light and is performed at room temperature, releasing molecular nitrogen as the only byproduct. To show the cross-linked polymer layers do not display inter-layer mixing, we deposited red-emitting regioregular poly(3-hexylthiophene-2,5-diyl) (P3HT) over cross-linked (10% cross-linker) blue emitting dioctyl polyfluorene (PFO) layer. The overlaid layers showed clear and well-defined boundary with no interlayer mixing. The surface morphology of the solution deposited layers was investigated by AFM to show that the cross-linked layers exhibited significant decrease in surface roughness. This is also shown on the example of the hole transporting material 4,4'-bis[N-(1-naphthyl)-N-phenylamino]-biphenyl (NPB) which displayed roughness average to decrease from 6.4 nm to 1.0 nm. The effect of decreased surface roughness on the performance of phosphorescent OLEDs was investigated by fabricating devices with configuration of ITO/PEDOT:PSS/NPB:(0%/5%/10%) cross-linker/MCP:6% Ir(mppy) 3 /TPBI/CsF/Al. Furthermore, following the diazirine-mediated cross-linking, the OLEDs displayed a decrease in turn-on voltage from 3.8 V to 3.0 V along with a six-fold enhancement of external quantum efficiency (EQE max ) from 1.1% to 6.8% and maximum luminous efficiency increase from 3.8 cd A -1 to 22.9 cd A -1 . These results demonstrate that the simple diazirine mediated photo-cross-linking using mild conditions compatible with organic layers is a promising strategy for improving the performance of the solution-processed OLEDs.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Polymer morphologh

All polymeric materials in their final application are aggregates of many molecules. For linear macromolecules, these aggregates are highly entangled and their macroscopic properties are affected in a little-known way by the interpenetration and entanglements of the molecules. Over the years, we have done occasional investigations of single molecule single crystals and found that there are many unsolved questions about their nucleation, growth, kinetically determined shape, and ultimate path to equilibrium morphology on annealing. This initial work could be extended by a study of the applicability of microgravity methods for the production and study of the formation of single molecule particles. The production of separated molecules of sufficient size to produce phase-like behavior would involve perhaps a spray of solutions containing single molecules, followed by evaporation of the volatiles, or precipitation out of dispersion droplets. Other methods may involve Langmuir films etc., as shown in our prior work. The microgravity environment should enhance the efficiency of any of these methods by avoiding the joining of growing particles by reduction of convection and settling due to density differences. Once produced, the single molecule droplets are to be quenched into the glassy state and analyzed morphologically and thermally. Their shape alone can be used for molecular mass determination (an old problem that suffered from the need to estimate the shape of collapsed (flat) droplets on a surface). Next would be the study of changes of properties as a function of time, temperature, and molecular mass (and distribution) on fusion to macroscopic single phases.

Wunderlich, Bernhard↗
DOE OSTI2023

Crystal structures of polymerized lithium chloride and dimethyl sulfoxide in the form of {2LiCl·3DMSO} n and {LiCl·DMSO} n

Two novel LiCl·DMSO polymer structures were created by combining dry LiCl salt with dimethyl sulfoxide (DMSO), namely, catena-poly[[chlorido­lithium(I)]-μ-(dimethyl sulfoxide)-κ 2 O:O-[chlorido­lithium(I)]-di-μ-(dimethyl sulfoxide)-κ 4 O:O], [Li 2 Cl 2 (C 2 H 6 OS) 3 ]n, and catena-poly[lithium(I)-μ-chlorido-μ-(dimethyl sulfoxide)-κ 2 O:O], [LiCl(C 2 H 6 OS)]n. The initial synthesized phase had very small block-shaped crystals (<0.08 mm) with monoclinic symmetry and a 2 LiCl: 3 DMSO ratio. As the solution evaporated, a second phase formed with a plate-shaped crystal morphology. After about 20 minutes, large (>0.20 mm) octa­hedron-shaped crystals formed. The plate crystals and the octa­hedron crystals are the same tetra­gonal structure with a 1 LiCl: 1 DMSO ratio. These structures are reported and compared to other known LiCl·solvent compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1972

Extended chain crystals of linear high polymers.

Studies of extended chain crystals carried out over the last 10 years have been reviewed. Crystallization in an extended chain conformation is possible either by chain folding followed by extension in the solid state, or by crystallization during polymerization. The equilibrium isometric crystal habit is only rarely exhibited. Crystals which derive from folded chain macroconformation by subsequent chain extension have lamellar habit, crystals which crystallize during polymerization often show fibrillar habit because of nucleation limitation. The morphology of extended chain crystals is analogous to folded chain crystals. Their properties have been shown to be close to the extrapolated equilibrium properties.

Wunderlich, B.↗
DOE OSTI2024

Solution-Processable Polymer Donor-Small Molecule Acceptor Bulk Heterojunction Organocatalysts for Enhancing CO 2 -to-CO Photoconversion

Metal-free organic semiconductors have emerged as a kind of promising star material in photocatalysis. However, their photocatalytic efficacy is impeded by the great recombination rate of the photogenerated charge carriers. Herein, we demonstrate the devising of solution-processable organic semiconductor bulk heterojunction (BHJ) systems with varying ratios by using BP3DT and PC 61 BM as the donor (D) and acceptor (A) candidates, respectively, for enhanced selective CO production from CO 2 photoreduction. The prepared BP3DT/PC 61 BM BHJs are solution-processed on both glass substrates (GS) and molecular sieves (MS) via a drop-casting technique to form an active thin film and porous photocatalysts to catalyze CO production. All BP3DT/PC 61 BM BHJs efficiently produce CO as the primary product in the existence of trace-level TEA/H 2 O (0.5 mL). Our results show that the photocatalytic efficiency depended on the D/A w% ratios and its nanoscale phase separation morphology within the BHJ, contributing to the promotion of exciton dissociation. Additionally, the BHJ undergoes an ostensible morphological transition from large-scale phase-separation to a fine mixed homogeneous nanoscale by varying the BP3DT/PC 61 BM blend ratio from 30/70 w% to 70/30 w%, which increases the interfacial area and shortens the distance of the exciton to the D/A surface, and promotes charge carrier separation, corroborated by photo-optical and photoelectrochemical experimental results. Accordingly, the resulting BP3DT/PC 61 BM BHJ@MS with a D/A ratio of 70/30 w% achieves a CO yield of 819 μmol·g cat -1 h -1 , surpassing those of pure PC 61 BM (126 μmol·g cat -1 h -1 ) and BP3DT (72 μmol·g cat -1 h -1 ) by 6.5- to 11.3-fold and also exceeding that of metal-free linear conjugated polymer-based organocatalysts reported to date. Specifically, this is the first work to develop an organic-semiconductor-based BHJ photocatalyst, which may offer a nascent way to design more efficient organocatalysts for CO 2 reduction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Synergistic Use of Pyridine and Selenophene in a Diketopyrrolopyrrole‐Based Conjugated Polymer Enhances the Electron Mobility in Organic Transistors

Abstract To achieve semiconducting materials with high electron mobility in organic field‐effect transistors (OFETs), low‐lying energy levels (the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO)) and favorable molecular packing and ordering are two crucial factors. Here, it is reported that the incorporation of pyridine and selenophene into the backbone of a diketopyrrolopyrrole (DPP)‐based copolymer produces a high‐electron‐mobility semiconductor, PDPPy‐Se. Compared with analogous polymers based on other DPP derivatives and selenophene, PDPPy‐Se features a lower LUMO that can decrease the electron transfer barrier for more effective electron injection, and simultaneously a lower HOMO that, however, can increase the hole transfer barrier to suppress the hole injection. Combined with thermal annealing at 240 °C for thin film morphology optimization to achieve large‐scale crystallite domains with tight molecular packing for effective charge transport along the conducting channel, OFET devices fabricated with PDPPy‐Se exhibit an n‐type‐dominant performance with an electron mobility (μ e ) as high as 2.22 cm 2 V −1 s −1 and a hole/electron mobility ratio (μ h /μ e ) of 0.26. Overall, this study demonstrates a simple yet effective approach to boost the electron mobility in organic transistors by synergistic use of pyridine and selenophene in the backbone of a DPP‐based copolymer.

Liu, Qian↗
DOE OSTI2021

Facilitating Large‐Scale Snow Shedding from In‐Field Solar Arrays using Icephobic Surfaces with Low‐Interfacial Toughness

Abstract Large‐scale accrual of snow and ice on solar arrays in northern latitudes can cause significant power generation losses during winter. Depending on environmental conditions, snow can encompass a wide range in physical characteristics from dry snow (modulus ≈100 kPa and density ≈0.1 g cm −3 ) to bulk ice (modulus ≈8 GPa and density ≈0.9 g cm −3 ). This variation in snow morphology has made the development of a passive, broad‐spectrum, snow and ice‐shedding surface challenging. Here, the authors develop one of the first surfaces that simultaneously possesses both low‐interfacial strength ( τ˄ ice < 50 kPa) and toughness (Γ ice < 0.5 J m −2 ) with ice. These surfaces, fabricated via the addition of mobile polymer chains/oils to a thin polymeric coating, require extremely low detachment forces for ice, enabling its passive shedding at virtually any accretion length scale. Preliminary evidence that the new surfaces can shed different forms of snow and ice from field‐deployed solar arrays, over a range of subzero temperatures for several weeks, leading to significant increases in power generation is provided. The optically transparent surfaces are easily scalable and can be widely deployed by the solar industry in areas that see persistent snow. Other applications include automotive windshields, LIDAR covers for autonomous vehicles, and cold climate optical sensors.

Dhyani, Abhishek↗
DOE OSTI2023

Appealing sheath‐core spun high‐performance composite carbon molecular sieve membranes

Abstract Carbon molecular sieve (CMS) membranes are attractive candidates to meet requirements for challenging gas separations. The added ability to maintain such intrinsic properties in an asymmetric morphology with a structure that we term a “Pseudo Wheel+Hub & Spoke” asymmetric form offers new opportunities. For CMS membrane, specifically, the structure provides both selective layer support and low flow resistance even for high feed pressures and fluxes in CO 2 removal from natural gas. This capability is unavailable to even rigid glassy polymers due to the much higher modulus of CMS materials. Combining precursor asymmetric hollow fiber formation and optimized pyrolysis creates a defect free CMS proof‐of‐concept membrane for this application. Facile formation of the sheath‐core spun precursor with a 6FDA‐DAM sheath and Matrimid® core also avoids the need to seal defects before or after the carbonization of the precursors. The composite CMS membrane shows CO 2 /CH 4 (50 : 50) mixed gas feed with an attractive CO 2 /CH 4 selectivity of 64.3 and CO 2 permeance of 232 GPU at 35 °C. A key additional benefit of the approach is reduction in use of the more costly high performance 6FDA‐DAM in a composite sheath‐core CMS membrane with the “Pseudo Wheel+Hub & Spoke” structure.

Cao, Yuhe↗
NASA NTRS1992

Characterization of polymer films retrieved from LDEF

One of the trays aboard LDEF was an experiment having the objective of assessing the effects of long term exposure of candidate balloon films, tapes, and lines to the hostile environment of space. The fortuitous location of these materials on LDEF minimized direct impact by atomic oxygen thus providing an opportunity to study the effects of low earth orbit environments on polymeric materials without the worry of atomic oxygen abrasion. The resulting chemical, morphological, and thermomechanical changes for polyethylene specimens are reviewed. In addition, preliminary data for fluorinated ethylene/propylene copolymers used for thermal blankets is presented. Polyethylene is observed to crosslink and branch from exposure to atomic oxygen and/or ultraviolet with a decrease in crystallinity.

Letton, Alan↗
DOE OSTI2024

Multiscale porosity characterization in additively manufactured polymer nanocomposites using micro-computed tomography

Extrusion-based additive manufacturing (AM) of polymer composites exhibits complex thermally driven phenomena that introduce severe discontinuities in the internal structure across length scales, especially voids or porosity. This study utilizes a high-throughput porosity characterization technique to analyze large datasets from numerous micro-computed tomography (mu CT) scans to capture the influence of AM print parameters on the size, shape, and location of porosity across multiple print layers (up to a few cm) on fused granular fabrication (FGF) printers. The materials investigated include nanocomposite formulations based on commercially relevant nylon-12 and polyether ketone ketone (PEKK) materials comprising nano- or micro- sized fillers. The estimated global porosity follows an inverse linear correlation against the bulk density of the printed samples. Increasing the extrusion multiplier (EM) and the nozzle temperature while decreasing the print speeds reduces the global porosity. Outlier analyses (local porosity morphology) show that faster print speeds and higher extrusion rates result in long, slender inter-layer voids, while lower nozzle temperatures lead to large, symmetrical, inter-bead voids (at the bead junction). Lack of active chamber temperature increases inter-layer and intra-bead voids with a two-fold increase in global porosity. Overall, the micro filler-reinforced composites exhibit higher global porosity than nanofiller-reinforced composites, which is attributed to the increased mismatch in the thermal expansion coefficient between the filler and the polymers used in the study.

36 MATERIALS SCIENCE↗