Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Passive Thermal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

NanoSail-D

The "NanoSail-D" mission is currently scheduled for launch onboard a Falcon-1 Launch Vehicle in the early June 2008 timeframe. The NanoSail-D spacecraft will consist of a solar sail subsystem stowed in a 2U volume and a 1U spacecraft bus, provided by Ames Research Center. The primary objectives of the NanoSail-D technology demonstration mission are to fabricate, stow and deploy on-orbit a solar sail and perform a de-orbit maneuver to demonstrate a potential orbital debris mitigation technology. The NanoSail-D mission is being developed through a collaborative effort between the NASA Marshall Space Flight Center and the NASA Ames Research Center Small Spacecraft Office. Details of the NanoSail-D system will be presented, including: 1) design details of the solar sail reflective membrane quadrants, gossamer booms, deployment system and passive attitude control system, 2) design analysis results including structural, thermal, environmental, orbital debris and safety, and 3) test results including deployment, ascent venting, launch vibration and PPOD integration verification.

Montgomery, Edward E., IV↗
NASA NTRS2010

Wide-Band Heterodyne Submillimetre Wave Spectrometer for Planetary Atmospheres

We present calculations and measurements on a passive submillimetre wave spectroscopic sounder to gather data on the thermal structure, dynamics and composition of the upper atmosphere of a planet, e.g. the stratosphere of Jupiter, or the entire thickness of the atmosphere of Mars. The instrument will be capable of measuring wind speeds, temperature, pressure, and key constituent concentrations in the stratosphere of the target planet. This instrument consists of a Schottky diode based front end and a digital back-end spectrometer. It differs from previous space-based spectrometers in its combination of wide tunability (520-590 GHz), and rapid frequency switching between widely spaced lines within that range. This will enable near simultaneous observation of multiple lines, which is critical to the reconstruction of atmospheric pressure and density versus altitude profiles. At the same time frequency accuracy must be high to enable wind speeds to be determined directly by measurement of the line's Doppler shift.

Submillimeter↗
NASA NTRS2012

Precipitation from Space: Advancing Earth System Science

Of the three primary sources of spatially contiguous precipitation observations (surface networks, ground-based radar, and satellite-based radar/radiometers), only the last is a viable source over ocean and much of the Earth's land. As recently as 15 years ago, users needing quantitative detail of precipitation on anything under a monthly time scale relied upon products derived from geostationary satellite thermal infrared (IR) indices. The Special Sensor Microwave Imager (SSMI) passive microwave (PMW) imagers originated in 1987 and continue today with the SSMI sounder (SSMIS) sensor. The fortunate longevity of the joint National Aeronautics and Space Administration (NASA) and Japan Aerospace Exploration Agency (JAXA) Tropical Rainfall Measuring Mission (TRMM) is providing the environmental science community a nearly unbroken data record (as of April 2012, over 14 years) of tropical and sub-tropical precipitation processes. TRMM was originally conceived in the mid-1980s as a climate mission with relatively modest goals, including monthly averaged precipitation. TRMM data were quickly exploited for model data assimilation and, beginning in 1999 with the availability of near real time data, for tropical cyclone warnings. To overcome the intermittently spaced revisit from these and other low Earth-orbiting satellites, many methods to merge PMW-based precipitation data and geostationary satellite observations have been developed, such as the TRMM Multisatellite Precipitation Product and the Climate Prediction Center (CPC) morphing method (CMORPH. The purpose of this article is not to provide a survey or assessment of these and other satellite-based precipitation datasets, which are well summarized in several recent articles. Rather, the intent is to demonstrate how the availability and continuity of satellite-based precipitation data records is transforming the ways that scientific and societal issues related to precipitation are addressed, in ways that would not be otherwise possible. These developments have taken place in parallel with the growth of an increasingly interconnected scientific environment. Scientists from different disciplines can easily interact with each other via information and materials they encounter online, and collaborate remotely without ever meeting each other in person. Likewise, these precipitation datasets are quickly and easily available via various data portals and are widely used. Within the framework of the NASA/JAXA Global Precipitation Measurement (GPM mission, these applications will become increasingly interconnected. We emphasize that precipitation observations by themselves provide an incomplete picture of the state of the atmosphere. For example, it is unlikely that a richer understanding of the global water cycle will be possible by standalone missions and algorithms, but must also involve some component of data, where model analyses of the physical state are constrained alongside multiple observations (e.g., precipitation, evaporation, radiation). The next section provides examples extracted from the many applications that use various high-resolution precipitation products. The final section summarizes the future system for global precipitation processing.

Kucera, Paul A.↗
NASA NTRS1972

Thermal protection system trade studies on ablators and reuseable surface insulation

Analytical trade studies are presented that consider passive TPS configurations using the following material categories: (1) reuseable surface insulation - surface-coated rigidized ceramic fiber; (2) low density charring ablators; and (3) carbon-carbon and high density ablators for leading edge areas. Emphasized are effects on TPS weight by variations in entry trajectories and material thermal characteristics.

Strouhal, G.↗
NASA NTRS2011

A High-Resolution Measurement of Ball IR Black Paint's Low-Temperature Emissivity

High-emissivity paints are commonly used on thermal control system components. The total hemispheric emissivity values of such paints are typically high (nearly 1) at temperatures above about 100 Kelvin, but they drop off steeply at lower temperatures. A precise knowledge of this temperature-dependence is critical to designing passively-cooled components with low operating temperatures. Notable examples are the coatings on thermal radiators used to cool space-flight instruments to temperatures below 40 Kelvin. Past measurements of low-temperature paint emissivity have been challenging, often requiring large thermal chambers and typically producing data with high uncertainties below about 100 Kelvin. We describe a relatively inexpensive method of performing high-resolution emissivity measurements in a small cryostat. We present the results of such a measurement on Ball InfraRed BlackTM(BIRBTM), a proprietary surface coating produced by Ball Aerospace and Technologies Corp (BATC), which is used in spaceflight applications. We also describe a thermal model used in the error analysis.

Tuttle, Jim↗
NASA NTRS2024

Investigation into the Origin of the RF Phase Noise for the LISA Laser Transmitter

The Laser Interferometer Space Antenna (LISA) mission is a collaborative consortium led by the European Space Agency (ESA)in cooperation with the National Aeronautics and Space Administration (NASA). LISA’s goal is to capture gravitational wave events, such as spacetime distortions caused by massive orbiting bodies. Multiple low noise, single frequency master oscillator power amplifier (MOPA) lasers with a polarization-maintaining Yb-fiber amplifier will serve as the light sources for the LISA observatory. The NASA Goddard Space Flight Center (GSFC)is currently developing the laser transmitters for this project. The LISA lasers will carry radio frequency (RF)sidebands for exchanging reference RF clock information between spacecrafts. Excess phase noise, especially carrier-sideband differential phase noise added to the modulation side band by the phase modulator and the fiber amplifier, becomes a concern. In the gravitational wave frequency ranges, leading sources of this RF “differential” phase noise can be both intrinsic and extrinsic. Examples of intrinsic sources include thermal load on the active fiber, thermo-mechanical induced birefringence, and nonlinearities in the various passive and active fibers. Extrinsic sources can include external temperature fluctuations and infrasonic mechanical strain or vibrations. These noise spectra usually include both white and pink (1/f) thermal noise contributions. This work investigates the physical origins and impact of these sources of RF phase noise, and their characteristic spectra and management will be discussed.

Laser Interferometer Space Antenna↗
NASA NTRS2012

Heated-Atmosphere Airship for the Titan Environment: Thermal Analysis

Future exploration of Saturn's moon Titan can be carried out by airships. Several lighter-than-atmosphere gas airships and passive drifting heated-atmosphere balloon designs have been studied, but a heated-atmosphere airship could combine the best characteristics of both. This work analyses the thermal design of such a heated-atmosphere vehicle, and compares the result with a lighter-than-atmosphere (hydrogen) airship design. A design tool was created to enable iteration through different design parameters of a heated-atmosphere airship (diameter, number of layers, and insulating gas pocket thicknesses) and evaluate the feasibility of the resulting airship. A baseline heated-atmosphere airship was designed to have a diameter of 6 m (outer diameter of 6.2 m), three-layers of material, and an insulating gas pocket thickness of 0.05 m between each layer. The heated-atmosphere airship has a mass of 161.9 kg. A similar mission making use of a hydrogen-filled airship would require a diameter of 4.3 m and a mass of about 200 kg. For a long-duration mission, the heated-atmosphere airship appears better suited. However, for a mission lifetime under 180 days, the less complex hydrogen airship would likely be a better option.

Heller, R. S.↗
NASA NTRS1980

Passive microwave remote sensing of the ocean - A review

This paper reviews the current status of passive microwave remote sensing of the ocean. The physics of emission and instrumentation are highlighted in order to establish a relationship between the thermal emission and retrieved geophysical parameters. A discussion then follows on measurements of temperature, salinity, windspeed, etc. using passive microwave systems. These measurements are related to the accuracy and spatial resolution required by the users. The status of passive microwave remote sensing is summarized and recommendations for future research are presented.

Swift, C. T.↗
DOE OSTI2026

Advanced blade-shaped thermal energy storage device: Development and application

Thermal energy storage (TES) using phase change materials (PCMs) is a promising approach for capturing and reusing excess thermal energy, yet widespread adoption is limited by low thermal conductivity, bulky configurations, and inadequate scalability. Here, this study presents a modular, blade-shaped TES prototype designed to address these challenges. The device integrates a lightweight aluminum shell, an embedded serpentine coil for active or passive heat exchange, and a cost-effective corrugated metal mesh for enhanced PCM thermal conductivity. With thickness-to-length and thickness-to-width ratios of 0.03 and 0.08, respectively, the blade-shaped TES achieves a compact, modular form factor suitable for space-constrained applications. Experimental testing demonstrated the efficient charge and discharge behavior of blade-shaped TES, capturing PCM superheating, phase-change transitions, and subcooling dynamics, with charging and discharging efficiencies of 94.9% and 94.6%, respectively. Also, the system can potentially achieve higher energy density than that of conventional TES designs. When integrated into a household refrigerator during the study, three blade-shaped TES modules successfully shifted 100% of peak-time compressor operation to off-peak hours, reducing energy consumption while maintaining more stable compartment temperatures. The blade-shaped TES's thin geometry, modularity, and enhanced thermal performance support scalable deployment across residential, commercial, and industrial applications, providing a versatile, cost-effective solution for high-efficiency, demand-flexible thermal energy management.

Blade-shaped↗
NASA NTRS1999

The Effect of Penetration Depth on Thermal Contrast of NDT by Thermography

Nondestructive evaluation by Thermography (TNDE) is generally classified into two categories, the passive approach and the active approach. The passive approach is usually performed by measuring the natural temperature difference between the ambient and the material or structure to be tested. The active approach, on the other hand, requires the application of an external energy source to stimulate the material for inspection. A laser, a heater, a hot air blower, a high power thermal pulse, mechanical, or electromagnetic energy may provide the energy sources. For the external heating method to inspect materials for defects and imperfection at ambient temperature, a very short burst of heat can be introduced to one of the surfaces or slow heating of the side opposite to the side being observed. Due to the interruption of the heat flow through the defects, the thermal images will reveal the defective area by contrasting against the surrounding good materials. This technique is called transient Thermography, pulse video Thermography, or thermal wave imaging. As an empirical rule, the radius of the smallest defect should be at least one to two times larger than its depth under the surface. Thermography is being used to inspect void, debond, impact damage, and porosity in composite materials. It has been shown that most of the defects and imperfection can be detected. However, the current method of inspection using thermographic technique is more of an art than a practical scientific and engineering approach. The success rate of determining the defect location and defect type is largely depend on the experience of the person who operates thermography system and performs the inspection. The operator has to try different type of heat source, different duration of its application time, as well as experimenting with the thermal image acquisition time and interval during the inspection process. Further-more, the complexity of the lay-up and structure of composites makes it more difficult to determine the optimal operating condition for revealing the defects. In order to develop an optimal thermography inspection procedure, we must understand the thermal behavior inside the material subjected to transient heat in order to interpret the thermal images correctly. Fabrication of finite element models of characteristic defects in composite materials subjected to transient heat will enable the development of appropriate procedure for thermography inspection. Design of phantom defects could be modeled and behavior characterized prior to physically building these test parts. Since production of phantom test parts can be very time consuming and laborious, it is important to design good representative defects.

Chu, Tsuchin Philip↗
NASA NTRS1987

Composite Piston-Cap Structure

Design eliminates thermal stress between composite cap and metal piston. New, conically surfaced, composite piston-cap structure, passively retained in metallic piston, made from carbon/carbon material, machined to shape. Shape includes conical faces, conical extensions intersect at common vertex on cylindrical axis of piston body, allowing thermal-stress-free retention of cap at all temperatures. When assembly heated or cooled, metal expands or contracts radially from coincident vertex. Where metal makes contact with carbon/carbon cap, snugly fitting conical faces slide without interference. Since metal body free to expand, no thermal stress produced in metal body or carbon/carbon cap.

Taylor, Allan↗
NASA NTRS1984

The effect of the space environment on composite materials (A0138-9)

The objective is to test different types of materials (laminates, thermal coatings, and adhesives) to determine their actual useful lifetime. These experiments will also make is possible to integrate the histories of the thermal and mechanical characteristics into models of the composite structures. The experiment is passive and is located in one of the boxes in a 12-in.-deep peripheral tray with nine other experiments from France. The box will provide protection for the samples from contamination during the launch and reentry phases of the Long Duration Exposure Facility mission. The experiment revolves around four themes of study: thermal coatings, adhesives, dimensional stability, and mechanical characteristics. The various materials will be arranged in six levels within the box, so only the first level will be subjected to direct solar radiation. Each level will consist of plates from which test specimens will be cut after the mission.

Parcelier, M.↗
NASA NTRS1986

Thermal Analysis

The University of Georgia used NASTRAN, a COSMIC program that predicts how a design will stand up under stress, to develop a model for monitoring the transient cooling of vegetables. The winter use of passive solar heating for poultry houses is also under investigation by the Agricultural Engineering Dept. Another study involved thermal analysis of black and green nursery containers. The use of NASTRAN has encouraged student appreciation of sophisticated computer analysis.

Source record↗
DOE OSTI2022

Experimental and Numerical Study on the Effect of Annular Combustor Design on Thermal Uniformity Jet in Crossflow

Abstract Non-uniformity of the exit flow temperature represents one of the significant damages to gas-turbine components, particularly turbine blades. This may occur in the course of gas-turbine operation. This paper aims to provide passive techniques by modifying the combustor design rather than changing the flow parameters to improve the thermal uniformity and turbine blades to reduce thermal stresses and increase turbine blades’ life span. An acceptable agreement between the numerical and experimental results has been achieved, and the agreement includes the velocity and temperature profile. Four different angles have been tested numerically and experimentally with a maximum error of 5% at two different Reynolds numbers. Designing the outer combustor surface with a 45-deg angle bend can give a more uniform temperature distribution of 37% higher than the basic design with only a 0.5% higher pressure drop.

Energy & Fuels↗
NASA NTRS2005

The Impact of the Sun on Passive Remote Sensing at L-band

The sun is a strong source of radiation at L-band behaving roughly like a thermal source with a temperature ranging between 10(exp 5) - 10(exp 7) K, depending on solar activity. This is an important consideration at 1.4 GHz (the window set aside for passive use only) where future satellite sensors will operate to monitor soil moisture and sea surface salinity (e.g. SMOS, Aquarius, and Hydros). Straight forward calculations show that such a source of radiation can be a significant issue for these remote sensing applications, especially in the case of remote sensing of sea surface salinity. Radiation from the sun impacts passive remote sensing systems in several ways. First, is the solar radiation that comes directly from the sun (line-of-sight from sun to spacecraft that enters the radiometer through antenna side lobes). This is a particular problem for sensors in sunsynchronous orbits near the terminator (e.g. orbits with equatorial crossing times near 6am/6pm) because the spacecraft is in the sun most of the time. Second, is solar radiation that is reflected (specularly) from the mean surface to the radiometer. This contribution can be nearly as large as the direct ray, especially when the reflection is from the ocean surface which has a high reflection coefficient. Finally, there is "incoherent" signal reflected from the surface structure (roughness) to the radiometer antenna. Examples illustrating the significance of these terms is presented for the case of a pushbroom radiometer such as Aquarius and a conically scanning radiometer such as proposed for Hydros. Calculations are made using a set of theoretical patterns for these beams together with data on solar radiation obtained from by a worldwide network of observing stations known as Radio Solar Telescope Network (RSTN). Near solar minimum, solar contamination is not a problem unless the sun enters near the main beam. But near solar maximum, account must be made for radiation from the sun even when the signal enters in sidelobes far from the main beam.

LeVine, David M.↗
NASA NTRS1982

Thermal capabilities and graphical output of PAFEC

The program for automatic finite element calculations (PAFEC) developed for the computation of heat transfer in structures is discussed. The passive and interactive graphics capabilities of the PAFEC system are presented and future developments are outlined. This finite element system is shown to have significant thermal capabilities in support of its general structures. The program offers the following types of analysis: interactive graphics; user defined program control steps; steady state, transient heat transfer; boundary element methods; linear static, stress and displacements; modes and frequencies calculations; direct dynamic time intergration; frequency response analysis; elastohydrodynamic lubrication; large deflection analysis, buckling; creep and plasticity analysis; and substructures analysis.

Akin, J. E.↗