Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nuclear graphite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

High resolution x-ray Thomson scattering measurements from cryogenic hydrogen jets using the linac coherent light source

We present the first spectrally resolved measurements of x-rays scattered from cryogenic hydrogen jets in the single photon counting limit. The 120 Hz capabilities of the LCLS, together with a novel hydrogen jet design [J. B. Kim et al., Rev. Sci. Instrum. (these proceedings)], allow for the ability to record a near background free spectrum. Such high-dynamic-range x-ray scattering measurements enable a platform to study ultra-fast, laser-driven, heating dynamics of hydrogen plasmas. This measurement has been achieved using two highly annealed pyrolytic graphite crystal spectrometers to spectrally resolve 5.5 keV x-rays elastically and inelastically scattered from cryogenic hydrogen and focused on Cornell-SLAC pixel array detectors [S. Herrmann et al., Nucl. Instrum. Methods Phys. Res., Sect. A 718, 550 (2013)].

43 PARTICLE ACCELERATORS↗

Proton irradiated graphite grades for a long baseline neutrino facility experiment

In search of a low-Z pion production target for the Long Baseline Neutrino Facility (LBNF) of the Deep Underground Neutrino Experiment (DUNE) four graphite grades were irradiated with protons in the energy range of 140–180 MeV, to peak fluence of ~6.1×10 20 p/cm 2 and irradiation temperatures between 120–200 °C. The test array included POCO ZXF-5Q, Toyo-Tanso IG 430, Carbone-Lorraine 2020 and SGL R7650 grades of graphite. Irradiation was performed at the Brookhaven Linear Isotope Producer. Postirradiation analyses were performed with the objective of (a) comparing their response under the postulated irradiation conditions to guide a graphite grade selection for use as a pion target and (b) understanding changes in physical and mechanical properties as well as microstructure that occurred as a result of the achieved fluence and in particular at this low-temperature regime where pion graphite targets are expected to operate. A further goal of the postirradiation evaluation was to establish a proton-neutron correlation damage on graphite that will allow for the use of a wealth of available neutron-based damage data in proton-based studies and applications. Macroscopic postirradiation analyses as well as energy dispersive x-ray diffraction of 200 KeV x rays at the NSLS synchrotron of Brookhaven National Laboratory were employed. The macroscopic analyses revealed differences in the physical and strength properties of the four grades with behavior however under proton irradiation that qualitatively agrees with that reported for graphite under neutrons for the same low temperature regime and in particular the increase of thermal expansion, strength and Young’s modulus. The proton fluence level of ~10 20 cm -2 where strength reaches a maximum before it begins to decrease at higher fluences has been identified and it agrees with neutron-induced changes. X-ray diffraction analyses of the proton irradiated graphite revealed for the first time the similarity in microstructural graphite behavior to that under neutron irradiation and the agreement between the fluence threshold of ~5×10 20 cm -2 where the graphite lattice undergoes a dramatic change. The confirmed similarity in behavior and agreement in threshold fluences for proton and neutron irradiation effects on graphite reported for the first time in this study will enable the safe utilization of the wealth of neutron irradiation data on graphite that extends to much higher fluences and different temperature regimes by the proton accelerator community searching for multi-MW graphite targets.

43 PARTICLE ACCELERATORS↗

Pebble fuel design for the PB-FHR

This paper presents the results of parametric studies of pebble fuel that can guide the design of future PB-FHR cores. The pebble fuel designs are assessed using the following performance characteristics: burnup, reactivity feedback, transient response, timescale to reach equilibrium cycle, and protection of structural components. The performance of a thorium pebble blanket is assessed by comparing against a seed-only system and system that utilizes a graphite pebble reflector instead of a thorium blanket. This paper presents the functional requirements and a methodology to assess these fuel pebble designs. This paper identifies a feasible design space for low enriched uranium pebbles and selected a baseline pebble design for safe, economic energy generation. Furthermore, this study finds a thorium blanket does not increase the performance of the system significantly with respect to a graphite pebble reflector. Therefore, a graphite pebble reflector is recommended in the baseline full-core design to extend the lifetime of the outer solid graphite reflector to the life of plant. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Conversion of CO 2 into Synthetic Graphite

Carbon Dioxide (CO 2 ) can be utilized as a source for producing synthetic graphite. Our method converts CO 2 into solid carbon. These CO 2 -sourced solid carbon have an anisotropic property that allow them to be graphitized into synthetic graphite. Our patented thermal catalytic process uses carbon dioxide and hydrogen as the feedstocks for the reaction, producing solid carbon material, with distilled water as the sole byproduct. The process is designed as a closed loop, where all feedstock gases entering the reactor are converted into durable bulk carbons and water, with no emissions. These carbons materials can be sintered into a solid structure and then thermally annealed, taking the carbon atoms from a disordered state to a highly ordered state of graphitic material – producing synthetic graphite structures. Phase 1 will prove that these bulk carbons can be sintered into a machinable solid carbon structure, which will then be annealed into a fully graphitic solid structure. Standard analytics will be done to verify the extent of graphitization (Raman, XRD). Proving this CO 2 -sourced carbon pathway to synthetic graphite structures will give the US a domestic supply route for this critical material and remove reliance on foreign sources. In addition, since the synthetic graphite structure is made from CO 2 -sourced carbon, this is also a method to mitigate CO 2 . Graphite structures are used in high temperature and high friction applications, for example, as anodes for steel refining, for brake pad linings, as neutron reflectors in nuclear reactors.

36 MATERIALS SCIENCE↗

Coaxial pellets for metallic impurity injection on the large helical device

Two coaxial pellets with tungsten inserted into graphite carbon and polyethylene (PE) tubes are compared for tungsten spectroscopic study in the Large Helical Device. The tungsten pellet with carbon tube causes plasma collapse, while that with PE tube smoothly ablates without collapse. The deposition profile of the pellets is analyzed with a help of pellet ablation spectroscopy. It is found that the tungsten pellet with carbon tube can significantly penetrate into the core plasma and leads to the plasma collapse. A tungsten spectrum with radial profile is successfully observed when the tungsten pellet with PE tube is used.

36 MATERIALS SCIENCE↗

Codes and standards for ceramic composite core materials for High Temperature Reactor applications

Fiber-reinforced ceramic matrix composites are attractive for high-temperature nuclear applications due to excellent thermal and mechanical properties as well as reasonable-to-outstanding radiation resistance. Over the past 20 years, the use of ceramic matrix composite applications expanded to many commercial non-nuclear industries as fabrication and application of the technologies mature. The ASME Boiler Pressure Vessel Code, under Section III Division 5, provides the design and construction rules for High Temperature Reactor components. It published the first rules for ceramic matrix composites to be used for reactor core components. The rules lay out the quality requirements together with the design and materials criteria for the use and application of silicon carbide- and carbon-based matrix material technologies. As with the established graphite rules, the ceramic composite material rules are structured in Subsection HH (from Section III), that addresses the criteria for class SN nonmetallic core components. The code rules rely heavily on the development and publication of standards for composite specification, classification, and testing of mechanical, thermal, and other properties. These test methods are developed in ASTM Committee C28 on Advanced Ceramics, with a current focus on ceramic composite tubes. This article describes the detail of the composites code, the design methodology and similarities to the graphite code, the guidance for the development of specifications for ceramic composites (for nuclear applications) including recent standard developments, and it mentions the next steps to support licensing aspects by validating the code with benchmarking data.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Comparison of Fission Product Release Predictions using PARFUME and BISON with Results from the AGR-3/4 Irradiation Experiment

The PARFUME (PARticle Fuel ModEl) fuel performance modeling code and the BISON nuclear fuel performance application built on the Multiphysics Object-Oriented Simulation Environment (MOOSE) finite element library were used to predict the fission product release from tristructural isotropic (TRISO) coated fuel particles and compacts during the third and fourth irradiation experiment of the Advanced Gas Reactor (AGR-3/4) Fuel Development and Qualification Program. The fuel performance modeling codes PARFUME and BISON modeled the AGR-3/4 irradiation experiment using the fuel compact time-averaged volume averaged (TAVA) daily temperatures for a total irradiation duration of 369.1 effective full power days (EFPD) to predict the release fraction of the fission product silver (Ag-110m) from a representative TRISO-coated fuel particle from AGR-3/4 compacts. Post-irradiation examination (PIE) measurements provided data on the release of these fission products in the compacts outside of the silicon carbide (SIC) layer. The PARFUME and BISON results were then compared to the silver release measured from compact gamma scanning. The results showed good agreement between PARFUME and BISON but both codes under-predicted the silver release fraction for all the compacts. In addition, BISON was used to model and predict the fission product concentration radial profile outside of the compacts in capsules’ inner and outer rings. These rings were either comprised of matrix and/or structural graphite. To obtain the concentration profiles of silver, cesium, and strontium, a sorption isotherm model was developed in BISON to capture the effects of fission product transport across the gaps between the concentric rings. The general shape of the concentration radial profiles as calculated by BISON were similar in the inner ring (IR) but varied in the outer ring (OR) depending on the fission product of interest or capsule temperature. Using this methodology and model, BISON now has the capability to aid in developing new fission product diffusion coefficients for matrix or structural graphite materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Summary of US DOE R&D Activities on Graphite Oxidation (2006–2021)

The objective of the international collaboration between United States Department of Energy (U.S.-DOE) and Generation IV International Forum (GIF) is the development of the next generation of nuclear energy systems. The current GIF Project Arrangement (PA) on Materials (2018-2022) was revised in 2019 and extended for another 10 years (2020-2030). The Work Package 1 (“Graphite”) of the extended Project Plan (PP) on Materials specifies technical tasks and High Level Deliverables for research and development (R&D) activities related to using graphite in fuel elements, reflectors, and support structures of Very High Temperature Reactors (VHTR). The graphite tasks include specification and acquisition, qualification and development of new grades, characterization of properties, and development of behavior models. Specifically, Task 1.4 (“Graphite Oxidation Behavior”) outlines planned activities related to acute oxidation by air and chronic oxidation by impurities in the helium coolant. A final report on experimental data regarding graphite oxidation behavior is scheduled for 2022 (deliverable 3.1.1.4.a). In preparation of this deliverable, this document summarizes the R&D activities funded by U.S.-DOE from 2006 (the inception of the VHTR system arrangement) through present (2021). This report is being submitted to the GIF Graphite Working Group (GWG) to serve as input for the GWG high-level deliverable to the Project Management Board (PMB) of PA on Materials. Besides U.S.-DOE, other organizations participating to Task 1.4 of the current PA on Materials are: European Commission’s Joint Research Center (JRC), Korea Atomic Energy Research Institute (KAERI), and Japan Atomic Energy Agency (JAEA). U.S.-DOE is the main contributor on graphite oxidation R&D, with 85 % commitment of total funding during 2018-2022.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of Electrochemical Detectors for Elemental Characterization of Actinides - 20563

The characterization of the actinides contained in radioactive waste involves complex and expensive separation processes. Electrochemical methods allow identifying and quantifying quickly and accurately the elementary concentration of actinides such as Th, U, Pu, Am, and Cm in liquid waste. The objective of this research proposal is to build a low-cost portable miniaturized electrochemical detector, which can be an alternative for an initial characterization of actinides in liquid waste. Therefore, this work proposes the use of an electrochemical graphite detector modified with phthalocyanine, to detect and quantify actinides in aqueous media. The electrochemical response of the modified graphite electrodes was performed by cyclic voltammetry, and so the detection and quantification limits for U and Th were determined. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

UO{sub 2} and PuO{sub 2} utilization in high temperature engineering test reactor with helium coolant

High temperature engineering test reactor (HTTR) is one of high temperature gas cooled reactor (HTGR) types which has been developed by Japanese Atomic Energy Research Institute (JAERI). The HTTR is a graphite moderator, helium gas coolant, 30 MW thermal output and 950 °C outlet coolant temperature for high temperature test operation. Original HTTR uses UO{sub 2} fuel. In this study, we have evaluated the use of UO{sub 2} and PuO{sub 2} in form of mixed oxide (MOX) fuel in HTTR. The reactor cell calculation was performed by using SRAC 2002 code, with nuclear data library was derived from JENDL3.2. The result shows that HTTR can obtain its criticality condition if the enrichment of {sup 235}U in loaded fuel is 18.0% or above.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Failure Predictions for VHTR Core Components using a Probabilistic Contiuum Damage Mechanics Model

The proposed work addresses the key research need for the development of constitutive models and overall failure models for graphite and high temperature structural materials, with the long-term goal being to maximize the design life of the Next Generation Nuclear Plant (NGNP). To this end, the capability of a Continuum Damage Mechanics (CDM) model, which has been used successfully for modeling fracture of virgin graphite, will be extended as a predictive and design tool for the core components of the very high- temperature reactor (VHTR). Specifically, irradiation and environmental effects pertinent to the VHTR will be incorporated into the model to allow fracture of graphite and ceramic components under in-reactor conditions to be modeled explicitly using the finite element method. The model uses a combined stress-based and fracture mechanics-based failure criterion, so it can simulate both the initiation and propagation of cracks. Modern imaging techniques, such as x-ray computed tomography and digital image correlation, will be used during material testing to help define the baseline material damage parameters. Monte Carlo analysis will be performed to address inherent variations in material properties, the aim being to reduce the arbitrariness and uncertainties associated with the current statistical approach. The results can potentially contribute to the current development of American Society of Mechanical Engineers (ASME) codes for the design and construction of VHTR core components.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Enrichment of C-14 on surface deposits of Oldbury reactor graphite investigated with the use of magnetic sector secondary ion mass spectrometry - 15076

Large quantities of irradiated graphite containing C-14 will arise from the decommissioning of the UK's Magnox power stations. Magnetic sector secondary ion mass spectrometry (MS-SIMS) has been used to investigate the distribution of this radioisotope within a number of trepanned graphite samples from a variety of radial and axial positions within reactor one at Oldbury, a Magnox nuclear reactor. The methodology used for these determinations ensured that possible mass interferences between C-14 species and oxygen-bearing species were eliminated from the analysis. This work indicates that a carbonaceous deposit found on exposed channel wall face samples has a relative C-14 enrichment compared to the underlying graphite, with concentrations calculated between approximately 5 and 55 ppm. Samples without this deposit gave C-14 concentrations below the limits of detection of the instrument, verifying that the enrichment is due to the deposit. Variations in C-14 concentration with sample height have been shown, with samples lower in the core having an increased C-14 concentration compared with those higher up. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

ART Advance Graphite Creep (AGC) Irradiation Experiment

ART Advance Graphite Creep (AGC) Irradiation Experiment topics of discussion include: Schedule, AGC Experiment Update, AGC-4 Status, Anticipated areas data will be used, and Vendor specific irradiation capsule. This includes NRC/Licensing questions on irradiation behavior, behavior model development, and other collaborations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Interstellar grains in primitive meteorites - Diamond, silicon carbide, and graphite

Primitive meteorites contain a few parts per million (ppm) of pristine interstellar grains that provide information on nuclear and chemical processes in stars. Their interstellar origin is proven by highly anomalous isotopic ratios, varying more than 1000-fold for elements such as C and N. Most grains isolated thus far are stable only under highly reducing conditions (C/O greater than 1), and apparently are 'stardust' formed in stellar atmospheres. Microdiamonds, of median size about 10 A, are most abundant (about 400-1800 ppm) but least understood. They contain anomalous noble gases including Xe-HL, which shows the signature of the r- and p-processes. Silicon carbide, of grain size 0.2-10 microns and abundance about 6 ppm, shows the signature of the s-process and apparently comes mainly from red giant carbon (AGB) stars of 1-3 solar masses. Some grains appear to be not less than 10 exp 9 a older than the solar system. Graphite spherules of grain size 0.8-7 microns and abundance less than 2 ppm contain highly anomalous C and noble gases, as well as large amounts of fossil Mg-26 from the decay of extinct Al-26. They seem to come from at least three sources, probably AGB stars, novae, and Wolf-Rayet stars.

Anders, Edward↗

Status Report on ASME Code Development for Nonmetallic Core Components in 2020

The purpose of this report is to provide a status update on the progress and ongoing activities of the current ASME Boiler Pressure Vessel (BPV) Code Section III, Division 5, on nonmetallic core components and assemblies which includes the design rules for graphite and ceramic composite materials. Section III is concerned with the design and construction of nuclear reactor components and Division 5 focuses on high temperature reactors (HTR). The ASME Section III Committee’s function for nuclear items other than pressure-retaining components, is to establish rules of safety related to structural integrity. The term “construction” refers to the all-inclusive effort comprising of materials, design, fabrication, examination, inspection, testing, certification, and pressure relief. The Department of Energy (DOE) supports industry codes and standards development through focused research providing the technical basis for new or modified codes and standards and the participation of subject matter experts in codes and standards committees. The activities for the nonmetallic core components and assemblies committees are the pursuit of two working groups that meet quarterly during ASME BPV Code Week meetings. The two working groups are General Requirements for Graphite and Ceramic Composite Core Components and Assemblies (GR GCCCCA) and Nonmetallic Design and Materials (NDM). The rules on general requirements for nonmetallic core components are discussed in the articles of Subsection HA subpart B. Ceramic composites were recently incorporated within the rules, and the GR GCCCCA working group is now in the process of aligning the requirements with the subsections and articles of ASME BPV Code Section III NCA, the general requirements for Division 1 and 2 of the code. The NDM working group is concerned with the design rules for graphite and composite materials for core components and assemblies discussed in Subsection HH (Class SN Nonmetallic Core Components) subpart A and subpart B which reference graphite and composite materials respectively. The bulk of the progress and work is done within this working group. A significant undertaking, with discussion that started in 2015, is to gain endorsement of ASME Section III, Division 5, by the U.S. Nuclear Regulatory Commission (NRC). In June 2018, ASME formally recommended endorsement to the NRC. The NRC has since initiated the endorsement review process, which is to be concluded early in 2021. ASME task groups on metallic structures and components, as well as non-metallic core support structures, have been formed to define potential pathways and schedules for NRC endorsement of Division 5. NRC determined to perform a review on the 2017 edition of Section III Division 5 as a baseline. As a result, the use of graphite as nonmetallic core components formed part of the review, but it excluded composite materials (which were first introduced in the 2019 edition). This report documents progress in FY 2020 directed toward ASME’s efforts to develop design codes for graphite and composites. Progress includes a major code review by NRC, the first code enquiry, and its solution, an overhaul of the treatment of Weibull Statistics, and the addition of Nonmandatory Appendices to the composites code relating to carbon-carbon composite materials.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Study of treatment as an alternative WM pathway: examples of I-graphite and metallic components such as steam generators - 15212

EDF is working continuously to optimize and secure its waste management pathways, leading in some case to develop appropriate treatment solutions that could be implemented parallel to reference solutions, complementary or as alternative solutions to already existing paths. This approach is illustrated by the examples of steam generators replaced during the operation of French PWR power plants, and of irradiated graphite (stacks and sleeves), coming from the decommissioning of UNGG reactors, which have been shut down. Concerning graphite wastes, the near surface disposal facility intended for this waste does not exist yet, and is currently giving rise to the research of a suitable site, and an evaluation of its performances. While accompanying ANDRA (French national agency for nuclear waste management), in charge of the development of the facility, and while waiting for more data to be available, EDF is continuing the consolidation of graphite wastes radiological inventory, and is working on the development of an alternative management solution, based on a thermal treatment process. Depending on the nature of the treatment, and on the choice of operating parameters, this treatment may contribute to reduce graphite wastes volume and/or promote its acceptance in a disposal facility. Reducing the radiological inventory by decontamination is one of the means to achieve these objectives. Concerning replaced steam generators, nearly 200 of them will have been removed by 2030, and stored on site waiting for their treatment, which represents about 65 000 tons of metal. Initially intended to be cut and packed on NPPs' sites during their dismantling, EDF is studying the economic value of having the steam generators treated in a centralized facility, which allows reducing the volume of final wastes by optimizing cutting operations, while considering recycling after melting. However, this studied pathway implies a number of difficulties to be overcome. In particular, the shipment of such large components to a centralized facility may be complex. Moreover, French regulatory framework does not allow recycling outside nuclear industry, therefore limiting recycling opportunities to storage containers for radioactive wastes. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Fuels and Materials Challenges for the Very High Temperature Reactor

High Temperature Gas-cooled Reactors (HTGRs) featuring particle fuel are a very mature technology. Commercial deployment occurred in the mid-1980's with the Fort St.Vrain and Thorium Hochtemperatur Reaktor by providing electricity to the grids in the United States and West Germany, respectively. The technology was then adopted by Japan and China with the operation of the High Temperature Test Reactor in Oarai, Japan and the High Temperature Reactor (HTR-10) in China. These commercial reactors typically operate with an outlet coolant temperature of 750 deg. C to 800 deg. C. Increasing the outlet temperature of the HTGR to even higher temperatures above 900 deg. C will improve the thermodynamic efficiency of the system and enable application of a new class of gas reactor, the very high temperature reactor (VHTR), to provide process heat, electricity, and hydrogen to a broad range of industrial customers with the attendant benefits of improved energy security and reduced CO{sub 2} emissions. However, the increase in coolant outlet temperature presents a number of technical challenges associated with fuels and materials. For over a decade, the U.S. Department of Energy has been sponsoring a broad program of research and development with a goal of addressing the technical fuels and materials challenges to support deployment of a VHTR that could safely and economically operate at outlet temperatures of 750 to 950 deg. C. In summary, fuels and materials challenges exist with deploying a VHTR with an outlet temperature of 950 deg. C in the areas of structural materials, graphite and TRISO fuel. However, R and D is underway or has recently been completed suggesting that technical solutions are possible. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comparison of Irradiated and Unirradiated Graphite Oxidation Performance

This work examines the oxidation behavior of NBG-25 graphite using irradiated specimens and (not irradiated) companion specimens from the Advanced Graphite Creep (AGC) Experiment. Irradiated and companion specimens were quartered, split into four small samples, to enable four oxidation test runs for each (0.5 inch diameter by 0.25 inch tall) piggyback button obtained from the AGC Experiment inventory. These split samples were oxidized in air in a thermogravimetric analyzer (TGA) and benchmarked against observations with separately sourced same-grade specimens of three geometries oxidized either in the TGA or in a vertical furnace built and operated to satisfy the specifications of ASTM D7542. The study considers both irradiation damage and relief of damage by thermal annealing. A range of isothermal oxidation temperatures were tested for specimens exposed to a similar irradiation environment, nominally 6.5 dpa at 650°C. To assess the dose dependency of observed oxidation behavior, specimens with a range of irradiation exposures (up to 6.8 dpa) were tested at the single oxidation temperature of 650°C. In the conventional analysis (rate determined over the 5-10% mass loss range) any annealing effects appear to be negligible, while irradiation to ~6.5 dpa may double or triple the subsequent oxidation rate. However, examination of rate with extent of reaction (over incremental ranges from initial onset up to 5% mass loss) illustrates that (at least for ~6.5 dpa) irradiation initially inhibits oxidation. Slower rates of oxidation than companion split samples are clearly indicated across all oxidation temperatures tested up to ~0.5% mass loss. Over the range of 0.5-1% mass loss, regardless of normalization strategy, there is no statistically meaningful difference in oxidation rate. However, beyond 0.5% mass loss oxidation of the irradiated sample becomes progressively faster than the companion sample (up to the 10% mass loss level observed).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗