Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material Attractiveness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Role of stacking defects on the magnetic behavior of CrCl 3

Here, in the study of van der Waals–layered magnetic materials, the properties of CrCl 3 continue to attract attention. This compound is reported to undergo antiferromagnetic ordering below ~14 K, with a ferromagneticlike region proposed to exist between 14 and 17 K. Ideally, the crystal structure is rhombohedral (R) below ~235 K, separated from a higher-temperature monoclinic (M) phase by a layer-sliding structural phase transition. However, the structural transition is often inhibited even in bulk single crystals, allowing M-type layer stacking, reported to have a 10-fold greater interlayer magnetic coupling than R-type stacking, to be present at low temperature. To clarify the effect of stacking defects on CrCl 3 , we report magnetization measurements on samples of varying crystalline quality. At low applied magnetic field, some crystals predominantly show the T N = 14 K peak, but other crystals show hysteretic behavior and a magnetization enhancement at a slightly higher temperature (14 < T ≲ 17 K.) Samples with anomalous behavior exhibit a transition around ~2 T in isothermal magnetization-field data, evidence that M-type stacking defects are the source of these anomalies. Ground powder samples are especially likely to show strongly anomalous behavior. We suggest that the anomalous behavior arises from few-layer magnetic domains that form just above T N in an environment of mixed interlayer magnetic coupling strength. We argue that the influence of M-type stacking boundaries on sublattice magnetization is already observable in reported neutron scattering data, and may be responsible for an enhancement near 17 K in reported specific heat data.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Chiral Magnetism and High-Temperature Skyrmions in B20-Ordered Co-Si

Magnets with chiral crystal structures and helical spin structures have recently attracted much attention as potential spin-electronics materials, but their relatively low magnetic-ordering temperatures are a disadvantage. While cobalt has long been recognized as an element that promotes high-temperature magnetic ordering, most Co-rich alloys are achiral and exhibit collinear rather than helimagnetic order. Crystallographically, the B20-ordered compound CoSi is an exception due to its chiral structure, but it does not exhibit any kind of magnetic order. Here, we use nonequilibrium processing to produce B20-ordered Co 1+ x Si 1₋ x with a maximum Co solubility of x = 0.043. Above a critical excess-Co content x c = 0.028 ), the alloys are magnetically ordered, and for x = 0.043, a critical temperature $T_c$ = 328 K is obtained, the highest among all B20-type magnets. The crystal structure of the alloy supports spin spirals caused by Dzyaloshinskii-Moriya interactions, and from magnetic measurements we estimate that the spirals have a periodicity of about 17 nm. In this work, our density-functional calculations explain the combination of high magnetic-ordering temperature and short periodicity in terms of a quantum phase transition where excess-cobalt spins are coupled through the host matrix.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1991

Reaction engineering for materials processing in space: Reduction of ilmenite by hydrogen and carbon monoxide

Oxygen is a consumable material which needs to be produced continuously in most space missions. Its use for propulsion as well as life support makes oxygen one of the largest volume chemicals to be produced in space. Production of oxygen from lunar materials is of particular interest and is very attractive possibility. The kinetics and mechanism of reduction of ilmenite by carbon monoxide and hydrogen at 800 to 1100 C were investigated. The temporal profiles of conversion for carbon monoxide have a sigmoidal shape and indicate the presence of three different stages (induction, acceleration, and deceleration) during the reduction reaction. The apparent activation energy decreases from 18 kcal/mole at 10 percent conversion to 10 kcal/mole at 50 percent conversion. The reaction is first order with respect to carbon monoxide under the experimental conditions studied. Both SEM and EDX analysis show that the diffusion of Fe product away from the reaction front and through the TiO2 phase, followed by the nucleation and growth of a separate Fe phase are important steps affecting the process kinetics. The results from hydrogen reduction show that the mechanism of ilmenite reduction by hydrogen is similar to that by carbon monoxide. However, the titanium dioxide can be further reduced by hydrogen at 800 to 1000 C. The detailed comparison and theoretical modeling of both reduction processes is presented.

Zhao, Y.↗
NASA NTRS1991

Vapor core propulsion reactors

Many research issues were addressed. For example, it became obvious that uranium tetrafluoride (UF4) is a most preferred fuel over uranium hexafluoride (UF6). UF4 has a very attractive vaporization point (1 atm at 1800 K). Materials compatible with UF4 were looked at, like tungsten, molybdenum, rhenium, carbon. It was found that in the molten state, UF4 and uranium attacked most everything, but in the vapor state they are not that bad. Compatible materials were identified for both the liquid and vapor states. A series of analyses were established to determine how the cavity should be designed. A series of experiments were performed to determine the properties of the fluid, including enhancement of the electrical conductivity of the system. CFD's and experimental programs are available that deal with most of the major issues.

Diaz, Nils J.↗
NASA NTRS1992

Numerical calibration of the stable poisson loaded specimen

An analytical calibration of the Stable Poisson Loaded (SPL) specimen is presented. The specimen configuration is similar to the ASTM E-561 compact-tension specimen with displacement controlled wedge loading used for R-Curve determination. The crack mouth opening displacements (CMOD's) are produced by the diametral expansion of an axially compressed cylindrical pin located in the wake of a machined notch. Due to the unusual loading configuration, a three-dimensional finite element analysis was performed with gap elements simulating the contact between the pin and specimen. In this report, stress intensity factors, CMOD's, and crack displacement profiles are reported for different crack lengths and different contacting conditions. It was concluded that the computed stress intensity factor decreases sharply with increasing crack length, thus making the SPL specimen configuration attractive for fracture testing of brittle, high modulus materials.

Ghosn, Louis J.↗
NASA NTRS1993

Analytical stress intensity solution for the Stable Poisson Loaded specimen

An analytical calibration of the Stable Poisson Loaded (SPL) specimen is presented. The specimen configuration is similar to the ASTM E-561 compact-tension specimen with displacement controlled wedge loading used for R-curve determination. The crack mouth opening displacements (CMODs) are produced by the diametral expansion of an axially compressed cylindrical pin located in the wake of a machined notch. Due to the unusual loading configuration, a three-dimensional finite element analysis was performed with gap elements simulating the contact between the pin and specimen. In this report, stress intensity factors, CMODs, and crack displacement profiles, are reported for different crack lengths and different contacting conditions. It was concluded that the computed stress intensity factor decreases sharply with increasing crack length thus making the SPL specimen configuration attractive for fracture testing of brittle, high modulus materials.

Ghosn, Louis J.↗
NASA NTRS2001

Lessons Learned from Real-Time, Event-Based Internet Science Communications

For the last several years the Science Directorate at Marshall Space Flight Center has carried out a diverse program of Internet-based science communication. The Directorate's Science Roundtable includes active researchers, NASA public relations, educators, and administrators. The Science@NASA award-winning family of Web sites features science, mathematics, and space news. The program includes extended stories about NASA science, a curriculum resource for teachers tied to national education standards, on-line activities for students, and webcasts of real-time events. The focus of sharing science activities in real-time has been to involve and excite students and the public about science. Events have involved meteor showers, solar eclipses, natural very low frequency radio emissions, and amateur balloon flights. In some cases, broadcasts accommodate active feedback and questions from Internet participants. Through these projects a pattern has emerged in the level of interest or popularity with the public. The pattern differentiates projects that include science from those that do not, All real-time, event-based Internet activities have captured public interest at a level not achieved through science stories or educator resource material exclusively. The worst event-based activity attracted more interest than the best written science story. One truly rewarding lesson learned through these projects is that the public recognizes the importance and excitement of being part of scientific discovery. Flying a camera to 100,000 feet altitude isn't as interesting to the public as searching for viable life-forms at these oxygen-poor altitudes. The details of these real-time, event-based projects and lessons learned will be discussed.

Phillips, T.↗
NASA NTRS1984

The Space Block

Ciba-Geigy Corporation's "Space Block," technically known as TDT-177-51 Ren Shape epoxy model block, is a two-foot by two-foot by five- inch plastic block from which master models of the Space Shuttle protective tiles are cut by NC machines. Space Block is made of epoxy resin with low viscosity and slow curing time, enabling the large block to cure uniformly without cracking. Rockwell International uses master models of Shuttle tiles to check accuracy of NC machines accurately by comparing model dimensions with specifications. New epoxy resins are attracting broad interest as a replacement for traditional materials used in modeling auto, aerospace or other parts.

Source record↗
NASA NTRS2003

The Effect of Simulated Microgravity Environment of RWV Bioreactors on Surface Reactions and Adsorption of Serum Proteins on Bone-bioactive Microcarriers

Biomimetically modified bioactive materials with bone-like surface properties are attractive candidates for use as microcarriers for 3-D bone-like tissue engineering under simulated microgravity conditions of NASA designed rotating wall vessel (RWV) bioreactors. The simulated microgravity environment is attainable under suitable parametric conditions of the RWV bioreactors. Ca-P containing bioactive glass (BG), whose stimulatory effect on bone cell function had been previously demonstrated, was used in the present study. BG surface modification via reactions in solution, resulting formation of bone-like minerals at the surface and adsorption of serum proteins is critical for obtaining the stimulatory effect. In this paper, we report on the major effects of simulated microgravity conditions of the RWV on the BG reactions surface reactions and protein adsorption in physiological solutions. Control tests at normal gravity were conducted at static and dynamic conditions. The study revealed that simulated microgravity remarkably enhanced reactions involved in the BG surface modification, including BG dissolution, formation of bone-like minerals at the surface and adsorption of serum proteins. Simultaneously, numerical models were developed to simulate the mass transport of chemical species to and from the BG surface under normal gravity and simulated microgravity conditions. The numerical results showed an excellent agreement with the experimental data at both testing conditions.

Radin, Shula↗
NASA NTRS1999

Single-Crystal NiAl-X Alloys Tested for Hot Corrosion

Single-crystal nickel aluminide (NiAl) has been investigated extensively throughout the last several years as a potential structural material in aero-gas turbine engines. The attractive features of NiAl in comparison to Ni-base superalloys include a higher melting point, lower density, higher thermal conductivity, and excellent oxidation resistance. However, NiAl suffers from a lack of ductility and fracture toughness at low temperatures and a low creep strength at high temperatures. Alloying additions of hafnium (Hf), gallium (Ga), titanium (Ti), and chromium (Cr) have each shown some benefit to the mechanical properties over that of the binary alloy. However, the collective effect of these alloying additions on the environmental resistance of NiAl-X was unclear. Hence, the present study was undertaken to examine the hot corrosion behavior of these alloys. A companion study examined the cyclic oxidation resistance of these alloys. Several single-crystal NiAl-X alloys (where X is Hf, Ti, Cr, or Ga) underwent hot corrosion testing in a Mach 0.3 burner rig at the NASA Lewis Research Center. Samples were tested for up to 300 1-hr cycles at a temperature of 900 C. It was found that increasing the Ti content from 1 to 5 at.% degraded the hot corrosion behavior. This decline in the behavior was reflected in high weight gains and large corrosion mound formation during testing (see the figures). However, the addition of 1 to 2 at.% Cr to alloys containing 4 to 5 at.% Ti appeared to greatly reduce the susceptibility of these alloys to hot corrosion attack and negated the deleterious effect of the increased Ti addition.

Nesbitt, James A.↗
DOE OSTI2021

Catalytic materials for lithium-sulfur batteries: mechanisms, design strategies and future perspective

Lithium-sulfur batteries (LSBs) are attractive candidates for post-lithium-ion battery technologies because of their ultrahigh theoretical energy density and low cost of active cathode materials. However, the commercialization of LSBs remains extremely challenging primarily due to poor cycling performance and safety concerns, which are inherently caused by low conductivity of S 8 and Li 2 S, severe polysulfide shuttling, and high polarization by solid Li 2 S 2 /Li 2 S deposition. Catalytic materials could facilitate the large-scale practical application of LSBs by overcoming all these challenges. In this review, we investigate the sulfur species evolution in LSBs and explore the roles of catalytic materials in charge/discharge processes, highlighting the catalysis of solid S 8 to liquid polysulfides and solid Li 2 S 2 to Li 2 S. Furthermore, we offer systematic strategies from atomic to macro levels, including defect engineering, morphology engineering and catalyst compositing, to enhance catalysis efficiency in terms of sulfur supercooling, fast charge transfer, thiosulfate generation, disulfide bond cleavage, tuneable Li 2 S growth and Li 2 S decomposition enhancement. Finally, the design and availability of the proposed catalytic materials will further advance LSB technology from coin cells and pouch cells to the subsequent commercialization scale.

25 ENERGY STORAGE↗
NASA NTRS1983

An application of gap regenerator/expander precooled by two stage G-M refrigerator

The degradation of regenerator effectiveness below 10K is due to the imbalance of the heat capacity of the regenerator material and helium gas as a working fluid. One of the attractive methods to increase this efficiency could be realized by a gap regenerator system regarding helium gas property. This paper describes an experiment using pressurized helium gas as a regenerator material. A two stage G-M cycle refrigerator has been used for precooling the gap regenerator system. With this method, minimum temperature below 5K has been obtained when the precooling temperature maintained at 10K.

Matsubara, Y.↗
DOE OSTI2023

Synthesizing and formulating metal oxide nanoparticle inks for perovskite solar cells

The perovskite solar cell has commercial potential due to the low-cost of materials and manufacturing processes with cell efficiencies on par with traditional technologies. Nanomaterials have many properties that make them attractive for the perovskite devices, including low-cost inks, low temperature processing, stable material properties and good charge transport. In this feature article, the use of nanomaterials in the hole transport and electron transport layers are reviewed. Specifically, SnO 2 and NiO x are the leading materials with the most promise for translation to large scale applications. Here, the review includes a discussion of the synthesis, formulation, and processing of these nanoparticles and provides insights for their further deployment towards commercially viable perovskite solar cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Theoretical study of the crystal and electronic properties of α - RuI 3

The material α-RuCl 3 , with a two-dimensional Ru honeycomb sublattice, has attracted considerable attention because it may be a realization of the Kitaev quantum spin liquid. Recently, a new honeycomb material, α-RuCl 3 , was prepared under moderately high pressure, and it is stable under ambient conditions. However, different from α-RuCl 3 , α-RuI 3 was reported to be a paramagnetic metal without long-range magnetic order down to 0.35 K. Here, the structural and electronic properties of the quasi-two-dimensional α-RuI 3 are theoretically studied. First, based on first-principles density functional theory calculations, the ABC stacking honeycomb-layer R$\bar{3}$ (No. 148) structure is found to be the most likely stacking order for α-RuI 3 along the c axis. Furthermore, both R$\bar{3}$ and P$\bar{3}$1c are dynamically stable because no imaginary frequency modes were obtained in the phononic dispersion spectrum without Hubbard U. Moreover, the different physical behavior of α-RuI 3 compared to α-RuCl 3 can be understood naturally. The strong hybridization between Ru 4d and I 5p orbitals decreases the “effective” atomic Hubbard repulsion, leading the electrons of RuI3 to be less localized than in RuCl 3 . As a consequence, the effective electronic correlation is reduced from Cl to I, leading to the metallic nature of α-RuI 3 . Based on the DFT+U (Ueff=2 eV) plus spin-orbital coupling, we obtained a spin-orbit Mott insulating behavior for α-RuCl 3 and, with the same procedure, a metallic behavior for α-RuI 3 , in good agreement with experimental results. Furthermore, when introducing large (unrealistic) U eff =6 eV, the spin-orbit Mott gap opens in α-RuI 3 as well, supporting the physical picture we are proposing. Our results provide guidance to experimentalists and theorists working on two-dimensional transition metal tri-iodide layered materials.

2-dimensional systems↗
DOE OSTI2022

Superconductivity and Local Inversion-Symmetry Breaking

Inversion and time reversal are essential symmetries for the structure of Cooper pairs in superconductors. The loss of one or both leads to modifications to this structure and can change the properties of the superconducting phases in profound ways. Superconductivity in materials lacking inversion symmetry, or noncentrosymmetric materials, has become an important topic. These materials show unusual magnetic and magnetoelectric properties and can host topological superconductivity. Recently, crystal structures with local, but not global, inversion-symmetry breaking have attracted attention. Here, superconductivity can exhibit phenomena not naively expected in centrosymmetric materials. In this review, we first introduce the concept of locally noncentrosymmetric crystals and different material realizations. We then discuss consequences of such local symmetry breaking on the normal state electronic structure and the classification of superconducting order parameters. Finally, we review the expected and, in parts, already observed phenomenology of unconventional superconductivity and possible topological superconducting phases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Automated Process Planning for Embossing and Functionally Grading Materials via Site-Specific Control in Large-Format Metal-Based Additive Manufacturing

The potential for site-specific, process-parameter control is an attribute of additive manufacturing (AM) that makes it highly attractive as a manufacturing process. The research interest in the functionally grading material properties of numerous AM processes has been high for years. However, one of the issues that slows developmental progress in this area is process planning. It is not uncommon for manual programming methods and bespoke solutions to be utilized for site-specific control efforts. This article presents the development of slicing software that contains a fully automated process planning approach for enabling through-thickness, process-parameter control for a range of AM processes. The technique includes the use of parent and child geometries for controlling the locations of site-specific parameters, which are overlayed onto unmodified toolpaths, i.e., a vector-based planning approach is used in which additional information, such as melt pool size for large-scale metal AM processes, is assigned to the vectors. This technique has the potential for macro- and micro-structural modifications to printed objects. A proof-of-principle experiment is highlighted in which this technique was used to generate dynamic bead geometries that were deposited to induce a novel surface embossing effect, and additional software examples are presented that highlight software support for more complex objects.

36 MATERIALS SCIENCE↗
NASA NTRS1983

Applications of ethylene vinyl acetate as an encapsulation material for terrestrial photovoltaic modules

Terrestrial photovoltaic modules must undergo substantial reductions in cost in order to become economically attractive as practical devices for large scale production of electricity. Part of the cost reductions must be realized by the encapsulation materials that are used to package, protect, and support the solar cells, electrical interconnects, and other ancillary components. As many of the encapsulation materials are polymeric, cost reductions necessitate the use of low cost polymers. The performance and status of ethylene vinyl acetate, a low cost polymer that is being investigated as an encapsulation material for terrestrial photovoltaic modules, are described.

Cuddihy, E. F.↗
NASA NTRS1988

Optimization of low gravity materials processing experiments using expert systems

The use of an expert system for the control of materials processing experiments in a facility such as the Space Station provides a number of attractive features for insuring that certain critical process parameters can be used to optimize the productivity of the materials processing experiments. The proposed approach to implementation of an expert system utilizes a knowledge base of desired process characteristics which will provide the desired results. The knowledge base for each experiment will be created in conjunction with the scientific investigator in charge of the experiment. Improvements to the knowledge base will be expanded to include self learning sessions in ground based experiments in order to teach the expert system how to respond to perturbations in the process and update the knowledge base on what process change should be implemented in order to reach the desired end product. Design considerations using an on-line real time expert system such as PICON is studied. The types of experiments evaluated include several types of solidification experiments which will be performed on the Space Station.

Workman, Gary L.↗