Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MINIMIZATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Supporting Risk-Based Decision-Making to Minimize Facility-Associated Re-Introduction of Poliovirus: Phase I

Sandia National Laboratories and Gryphon Scientific, as supported and directed by the CDC Center for Preparedness and Response (CPR), studied the process of risk assessment and risk-based decision-making in facilities expected to continue possessing poliovirus strains. The first phase of the study was conducted in anticipation of developing a tool to support decision-making processes for poliovirus containment to minimize the risk of facility-associated re-introduction of poliovirus. The study results supported the starting assumption that risk management of poliovirus will be aided by more rigorous and consistent risk assessment and that experience-based risk assessment is, by itself, inadequate to understand risk in a post-eradication world. These results were derived from review of polio virus literature, oversight documents, current and expected practices, and from discussions with affected facilities. Based on these results and on additional discussions with facilities, the study team recommends development of a quantitative risk assessment tool as well as improving access to and the quality of data for informing risk-based decision-making.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2016

Minimize the Voltage Degradation in Li-rich Layered Oxide Cathode Materials by Morphology Control

Li-rich layered oxides, either as a solid solution or as a nano-composite of layered Li 2 MnO 3 and Li(TM)O 2 (TM=Ni, Co, Mn), draw significant attention as the next-generation cathode materials for high-energy-density lithium ion batteries in electric vehicles. Over the past twenty years, the discharge capacity at room temperature of these cathode materials has been improved from 200 mAh g -1 to over 320 mAh g -1 today, even higher at elevated temperatures. While the research has continued to push the limit of the available capacity of the materials throughout the years, there are many issues still unclear. And numerous scientific challenges, especially voltage degradation during cycling of these materials, that must be overcome to realize their utilization in commercial lithium ion batteries. Here, we report a design of modified co-precipitation method without ammonia addition to synthesize morphology controlled Li-rich material Li 1.2 Ni 0.2 Mn 0.6 O 2 as high energy density cathode for lithium ion batteries. The obtained material has spherical secondary particles with uniform dispersion. The secondary particles are dense, and have an average diameter of approximately 3 μm. These secondary spherical particles consist of primary particles with particle size approximately 150 nm. The morphology controlled sample can minimize voltage decay as well as improve capacity retention during cycling. And furthermore, the influence of morphology control on the cycling performance has been investigated through Transmission X-ray Microscope.

Zhang, Minghao↗
DOE OSTI2021

Signal Preconditioning to Minimize Impulse Response Contribution

A study was performed to identify a method to minimize the effect of a linear time-invariant (LTI) system impulse response on an input. Three methods were studied: Wiener filter, the N4SID algorithm and transfer function estimation, the latter two using functions from MATLAB’s System Identification Toolbox. Although all three methods were able estimate an unknown forward impulse response given an input/output time series pair, only the Wiener filter was able to estimate a system inverse which satisfactorily solved the problem using a cosine similarity measure.

42 ENGINEERING↗
DOE OSTI2021

Exploring Whether Subsurface Fluid Production Can Minimize Triggered Seismicity in Geothermal Fields

Fluid injection and production related to energy recovery and other industrial operations alter the pressure and stress state of subsurface reservoirs which can lead to induced seismicity. Here, the primary goal is to investigate the hypothesis that the modulation of stress state in subsurface reservoirs through fluid injection/production operations can reduce the likelihood of inducing seismicity. Validation of this mitigation strategy will provide an active operational method to control induced seismicity in subsurface reservoir exploitations such as geothermal energy recovery and carbon storage. In this project, we analyze the relationship between extensive fluid production and the paucity of aftershock activity at the Coso Geothermal plant (CGP) following the 2019 Ridgecrest earthquake sequence, where high rates of aftershock triggering were expected. We developed a high-fidelity multiphase coupled thermo-hydro-mechanical (THM) model to simulate fluid injection/production activities at the CGP between 1986 and 2020. THM results of surface subsidence due to high rates of fluid production agree well with field observations from global positioning system (GPS) and interferometric synthetic aperture radar (InSAR). Subsequently, the variations of pore pressure, temperature and stress state were used to drive numerical earthquake simulations of the aftershock response to the 2019 Ridgecrest earthquakes. The earthquake simulations show that seismic quiescence may occur following the Ridgecrest event, depending on the initial stress state at the time of the mainshock and at the initiation of geothermal energy production. Seismic quiescence occurs in 20% of the cases we explored, where rates are decreased by 50% of the background rate in the two years following the mainshock. In circumstances where aftershock rates increase near the CGP following Ridgecrest, the average rate change is a factor of two larger than background rates from simulations with no operations. These findings indicate that unlike many other operations that bring faults closer to failure, operations at the CGP are acting to stabilize faults such that triggering in the current stress state is minimal.

58 GEOSCIENCES↗
DOE OSTI2022

Towards optimal gas cooling with minimal aero-optical distortion for a laser amplifier head

Next-generation lasers combining high-peak-power, ultrashort pulses with high repetition rates have the potential to efficiently deliver the high-average-power outputs required by many emerging technologies and areas of research. This work introduces a three-stage workflow consisting of low- and high-fidelity fluid simulations, in addition to aero-optical analyses. The final goal is to optimize gas cooling within a laser amplifier head while maintaining minimal aero-optical distortions. Low-fidelity RANS simulations are used to obtain mean flow solutions and transition locations. High-fidelity LES simulations, informed by their RANS counterparts, provide solutions containing density fluctuations, which are then passed on to the aero-optical analysis. The aero-optical analysis provides insight into the optical quality of the laser beam passing through the flow found in the LES results.

42 ENGINEERING↗
DOE OSTI2022

A skew quadrupole for the AGS to minimize the polarization losses of the polarized beams

The partial helices installed in the Alternating Gradient Synchrotron (AGS) 9 [1] eliminate both, the imperfection and the vertical intrinsic spin resonances thus yielding a 70% polarized proton beam with rigidity 79.4 [Tm] with 2x10 11 protons/bunch at the end of the AGS acceleration cycle. The initial beam polarization at the exit of the 200 MeV Linac is measured to be 80%. The 10% loss of the polarization at the end of the AGS acceleration cycle is due to the horizontal spin resonances which are caused by the betatron oscillations of the beam in the presence of the partial helices. To reduce the effect of these horizontal spin resonances on the beam polarization, the “jump Quads method” is applied in the AGS [2] which eliminates, almost all, the horizontal spin resonances and increases the final polarization of the proton beam to the value of 70%. A study [3] shows that these horizontal spin resonances can be totally eliminated by introducing into the AGS ring, skew quadrupoles which linearly couple the beam motions to excite new horizontal spin resonances which minimize the horizontal-spin-resonances caused by the partial-helices.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Flexible Siting Criteria and Staff Minimization for Micro-Reactors

The economic potential of micro-reactors is vast and underestimated. Commonly-emphasized applications include niche markets such as remote communities, mines and military bases. However, micro-reactors could be used as flexible energy generators also for larger markets, such as mobile and containerized agriculture and manufacturing facilities, district heating, micro-grids for data centers, sea ports, airports and hospitals. The implication is that micro-reactors may have to be deployed also in non-remote locations. Successful implementation of micro-reactors needs a navigable and predictable licensing process, technology-appropriate siting restrictions, risk-informed emergency and safety requirements, and practical operating and maintenance requirements. The primary goal of this project was to develop siting criteria that are tailored to micro-reactors deployable in densely-populated areas, e.g., urban environments. To achieve that goal, we compared the characteristics of the MIT research reactor (MITR) with those of leading micro-reactor concepts (e.g., eVinci, USNC, Aurora), and evaluated whether and how the MITR design basis (e.g., inherent safety features, engineered safety systems, source term, emergency planning and emergency operating procedures) and associated regulations may be applicable to these new micro-reactors as well. What makes MITR a unique analogue in this context is its small power rating (6 MWt) and physical size, mode of operations (24/7 with a somewhat more commercial flavor than typical university reactors), and especially its urban location. Of course significant differences exist, such as mission (power production vs. research) and the reactor design itself. Leveraging the MITR experience, this project was able to generate criteria that will allow micro-reactors to realize their full economic potential as flexible heat and electricity generators for a diverse portfolio of applications in non-remote locations. As such, the outcome of this project might encourage investment in and use of micro-reactors. A second goal of the project was to conceptualize a model of operations for micro-reactors that would minimize the staffing requirements, and thus reduce the cost of electricity and heat generated by these systems. Here too our approach was to systematically review the MITR experience and requirements, as well as survey the innovations in autonomous control technologies and monitoring (e.g., advanced sensors, drones, robotics, AI) that would permit a dramatic reduction in staffing at future micro-reactor installations. The scope of work was expanded after the start date to include also an evaluation of micro-reactor security, using the so-called consequence-based analysis, and the development of a methodology to perform dynamic risk assessment for micro-reactors, using system theory and modeling and simulation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Optimal gas cooling with minimal aero-opticaldistortion for next generation high-average-power lasers (Progress report, Year 2)

Next-generation lasers that combine high-peak-power ultrashort pulses with high repetition rates have the potential to efficiently deliver the high-average-power outputs required for inertial fusion energy generation, laser-based particle acceleration, and to generate compact secondary x- and 𝛾-ray radiation sources, among others. The combination of long gain length with high surface-to-volume ratio to remove residual heat makes gas-cooled multi-slab amplifier heads an inherently aperture- and average power scalable technology that enables this new class of solid-state lasers, and their thermal management becomes the most pressing technical challenge. As the index-of refraction depends on the gas density, heat removal from the slab surfaces unavoidably entails scattering of propagated light from regions of high temperature fluctuations. The requirement to maximize convective heat extraction from the gain medium under the constraint of minimum optical aberration of the beam renders amplifier slab cooling a technological challenge at the intersection of aero-optics, fluid-mechanics and heat transfer. The goal of this research is to leverage computational fluid dynamics and aero optics simulations of different levels of fidelity to devise a numerical modeling and optimization framework for gas-cooled multi-slab amplifiers. The project will be conducted in close collaboration with the Advanced Photon Technologies Group at Lawrence Livermore National Laboratory, where a gas-cooled test stand for laser materials and thermal management structures will be developed and installed. The final goal of the collaborative effort is to manufacture and benchmark a physical prototype of an numerically optimized amplifier head design. Measurement data on solid-state and thermo-optical distortions will be used for the validation of the numerical models. The key technical challenge in this multi-objective design problem is that of balancing optimal heat removal with minimal optical distortion. To facilitate computationally efficient design optimization and, at the same time, deepen our basic understanding of the interaction of light with turbulence, a complementary study that combines high and low-fidelity flow simulations and aero-optical models is proposed. Along the lines of these two objectives and solution strategies, the project is organized into two thrusts.

42 ENGINEERING↗
DOE OSTI2023

Demonstrating Load-Shaping Capabilities of Cost Minimizing Heat Pump Water Heater Controls with Varying Price Profiles

Increased penetration of photovoltaics and electrification of traditionally gas appliances are exacerbating existing challenges in cost-effectively balancing electricity grid supply and demand. Decarbonization without incurring expensive transmission and distribution system capacity increases requires shifting building loads from peak demand times to peak renewable production times. Grid operators are evaluating new ways of encouraging load shifting, including using time-varying price structures to provide a financial incentive. If devices incorporate price-responsive controls, a price profile could be designed to yield a wide variety of load curves as needed to optimize grid functionality. Heat pump water heaters (HPWHs) are an ideal device for price-responsive controls because the storage tank enables them to optimize the timing of electricity consumption without impacting hot water delivery service. This paper presents work demonstrating how price-responsive controls for HPWHs can provide different load profiles, as needed to stabilize the grid, in response to different price profiles. HPWH manufacturers now include web API and CTA-2045 communication capabilities which enable sending load shaping control signals. Pilot studies and preliminary programs have utilized these capabilities with uniform control strategies to reduce 4-9 PM electricity consumption. However, no studies have developed flexible controls capable of both a) responding to constantly varying price profiles and b) customizing logic to match the needs of each HPWH. Berkeley Lab's CalFlexHub project is pioneering price-driven load flexibility by developing and deploying cost-minimizing controls utilizing setpoint setting signals for fleets of HPWHs in response to varying price profiles. Control development is based on simulations using the Flexible Heat Pump Water Heater Performance Predictor which captures the control decisions of a residential, integrated HPWH manufacturer’s on-board controller. The proposed cost-reducing controls respond to constantly changing price profiles, providing the ability to change the price profile to generate load curves as needed to maintain grid stability. Preliminary simulations studying the load shaping capabilities of price-responsive controls on a fleet of 60 HPWHs have demonstrated an average of a) 135.4% increases in load during low-price periods, b) >36.8% reductions in electricity peak-price period, and c) 6.2% electricity cost savings.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2023

Electrochemical aptamer-based sensors: leveraging the sensing platform for minimally-invasive microneedle measurements and fundamental exploration of sensor biofouling dynamics

The ability to track the concentrations of specific molecules in the body in real time would significantly improve our ability to study, monitor, and respond to diseases. To achieve this, we require sensors that can withstand the complex environment inside the body. Electrochemical aptamer-based sensors are particularly promising for in vivo sensing, as they are among the only generalizable sensing technologies that can achieve real-time molecular monitoring directly in blood and the living body. In this project, we first focused on extending the application space of aptamer sensors to support minimally-invasive wearable measurements. To achieve this, we developed individually-addressable sensors with commercial off-the-shelf microneedles. We demonstrated sensor function in buffer, blood, and porcine skin (a common proxy for human skin). In addition to the applied sensing project, we also worked to improve fundamental understanding of the aptamer sensing platform and how it responds to biomolecular interferents. Specifically, we explored the interfacial dynamics of biofouling – a process impacting sensors placed in complex fluids, such as blood.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Metallurgical and mechanical characterization of ATP-5 aluminum alloys for minimizing machining distortion

ATP-5 aluminum alloy was considered as an alternative to 6061-T651 aluminum alloy to minimize machining distortion. ATP-5 is a proprietary cast alloy that is compositionally similar to 5083 aluminum and is purported to have excellent machinability, stability, and corrosion response. Dimensional stability tests, mechanical testing, chemical analysis, microstructural analysis, and fractography were completed to understand the metallurgy of the ATP-5 alloy and assess its potential as a 6061-T651 alloy alternative. Ultimately, the ATP-5 was found to retain dimensional stability issues, albeit to a lesser extent, relative to the 6061-T651 alloy. Combined with the residual cast structure observed microstructurally and lot-to-lot mechanical property variation, the alloy was deemed not suitable for a structural application. Alternative uses of ATP-5 include tooling, molds, vacuum chucks, fixtures, and jigs, where the material can shine in non-load bearing applications with a need for dimensional control and machinability.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Assessment of the bioconversion potential of minimally processed seaweed by halophilic yeasts

Building an advanced economy using biomanufacturing requires robust sources of carbon for converting into chemicals and products. Macroalgae hold significant potential due to their fast growth rates, lack of freshwater usage, and lack of land usage. To be used as a common feedstock, there are two primary challenges that need to be addressed: 1) unusual chemical composition and 2) high salinity. A solution to both issues is to use a resilient, salt-loving organism with a broad consumption profile for the conversion of macroalgae. Here we evaluate the ability of the oleaginous yeast Rhodosporidium toruloides to grow in wild macroalgae-derived feedstocks and identify a conversion process that is functional for two species of Sargassum collected from the Caribbean using R. toruloides that does not require washing of the input seaweed material. Together this demonstrates a future avenue of work that minimizes freshwater usage for incorporating macroalgae as a biomanufacturing carbon source.

09 BIOMASS FUELS↗
DOE OSTI2026

Minimizing Electric Lighting Use With LASSI Lighting Controls in Controlled Environment Agriculture

The majority of energy use in controlled environment agriculture is typically from electric lighting. Certain lighting controls can help minimize the energy required in these operations. This analysis simulates a greenhouse with different types of lighting controls in different U.S. climates to explore the effects of the lighting controls on energy use.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2017

Scheduling Non-Preemptible Jobs to Minimize Peak Demand

Our paper examines an important problem in smart grid energy scheduling; peaks in power demand are proportionally more expensive to generate and provision for. The issue is exacerbated in local microgrids that do not benefit from the aggregate smoothing experienced by large grids. Demand-side scheduling can reduce these peaks by taking advantage of the fact that there is often flexibility in job start times. We then focus attention on the case where the jobs are non-preemptible, meaning once started, they run to completion. The associated optimization problem is called the peak demand minimization problem, and has been previously shown to be NP-hard. These results include an optimal fixed-parameter tractable algorithm, a polynomial-time approximation algorithm, as well as an effective heuristic that can also be used in an online setting of the problem. Simulation results show that these methods can reduce peak demand by up to 50% versus on-demand scheduling for household power jobs.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Minimal Energy Routing of a Leader and a Wingmate with Periodic Connectivity

We consider a route planning problem in which two unmanned vehicles are required to complete a set of tasks present at distinct locations, referred to as targets, with minimum energy consumption. The mission environment is hazardous, and to ensure a safe operation, the UVs are required to communicate with each other at every target they visit. The problem objective is to determine the allocation of the tasks to the UVs and plan tours for the UVs to visit the targets such that the weighted sum of the distances traveled by the UVs and the distances traveled by the communicating signals between them is minimized. We formulate this problem as an Integer program and show that naively solving the problem using commercially available off-the-shelf solvers is insufficient in determining scalable solutions efficiently. To address this computational challenge, we develop an approximation and a heuristic algorithm, and employ them to compute high-quality solutions to a special case of the problem where equal weights are assigned to the distances traveled by the vehicles and the communicating signals. For this special case, we show that the approximation algorithm has a fixed approximation ratio of 3.75. We also develop lower bounds to the optimal cost of the problem to evaluate the performance of these algorithms on large-scale instances. We demonstrate the performance of these algorithms on 500 randomly generated instances with the number of targets ranging from 6 to 100, and show that the algorithms provide high-quality solutions to the problem swiftly; the average computation time of the algorithmic solutions is within a fraction of a second for instances with at most 100 targets. Finally, we show that the approximation ratio has a variable ratio for the weighted case of the problem. Specifically, if ρ denotes the ratio of the weights assigned to the distances representing the communication and travel costs, the algorithm has an a posteriori ratio of $3 + \frac{3ρ}{4}$ when ρ ≥ 1, and $\frac{3}{ρ}$ + $\frac{3}{4}$ when ρ ≤ 1.

42 ENGINEERING↗
DOE OSTI2019

Optimization of Component Sizing for a Fuel Cell-Powered Truck to Minimize Ownership Cost

In this study, we consider fuel cell-powered electric trucks (FCETs) as an alternative to conventional medium- and heavy-duty vehicles. FCETs use a battery combined with onboard hydrogen storage for energy storage. The additional battery provides regenerative braking and better fuel economy, but it will also increase the initial cost of the vehicle. Heavier reliance on stored hydrogen might be cheaper initially, but operational costs will be higher because hydrogen is more expensive than electricity. Achieving the right tradeoff between these power and energy choices is necessary to reduce the ownership cost of the vehicle. This paper develops an optimum component sizing algorithm for FCETs. The truck vehicle model was developed in Autonomie, a platform for modelling vehicle energy consumption and performance. The algorithm optimizes component sizes to minimize overall ownership cost, while ensuring that the FCET matches or exceeds the performance and cargo capacity of a conventional vehicle. Class 4 delivery truck and class 8 linehaul trucks are shown as examples. We estimate the ownership cost for various hydrogen costs, powertrain components, ownership periods, and annual vehicle miles travelled.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

Minimizing Ecological Impacts of Marine Energy Lighting

Marine energy is poised to become an important renewable energy contributor for the U.S., but widespread deployment of the technology hinges on its benefits outweighing the potential ecological impacts. One stressor marine energy installations introduce is light, which is known to cause varying responses among wildlife and has not yet been addressed as an environmental concern. This review discusses requirements and regulations for similar structures and how lighting design choices can be made to meet these requirements while minimizing environmental consequences. More practical guidance on implementing lighting for marine energy is needed, as well as updated guidelines to reflect technological and research advances. Known responses of wildlife to light are introduced in addition to how the responses of individuals may lead to ecosystem-level changes. The impact of light associated with marine energy installations can be reduced by following basic guidance provided herein, such as removing excess lighting, using lights with high directionality, and employing controls to reduce light levels. Continued research on animal responses to light, such as findings on minimum light levels for animal responses, alongside the development of highly-sensitivity spectral characterization capabilities can further inform lighting guidelines for deploying future open ocean marine energy devices.

54 ENVIRONMENTAL SCIENCES↗