Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LEVEL WIDTHS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Investigation of GaN-on-GaN vertical p - n diode with regrown p -GaN by metalorganic chemical vapor deposition

Here, to mimic selective-area doping, p -GaN was regrown on an etched GaN surface on GaN substrates by metalorganic chemical vapor deposition. Vertical GaN-on-GaN p - n diodes were fabricated to investigate the effects of the etch-then-regrowth process on device performance. The crystal quality of the sample after each epitaxial step was characterized by X-ray diffraction, where the etch-then-regrowth process led to a very slight increase in edge dislocations. A regrowth interfacial layer was clearly shown by transmission electron microscopy. Strong electroluminescence was observed with three emission peaks at 2.2 eV, 2.8 eV and 3.0 eV, respectively. The forward current density increased slightly with the increasing temperature, while the reverse current density was almost temperature independent indicating tunneling as the reverse transport mechanism. This result is very similar to the reported Zener tunnel diode comprising a high doping profile at the junction interface. High levels of silicon and oxygen concentrations were observed at the regrowth interface with a distribution width of ~100 nm. This work provides valuable information of p -GaN regrowth and regrown GaN p - n diodes, which can serve as an important reference for developing selective doping for advanced GaN power electronics for high voltage and high power applications.

42 ENGINEERING↗

Self-similarity of a Rayleigh–Taylor mixing layer at low Atwood number with a multimode initial perturbation

High-fidelity large eddy simulation (LES) of a low-Atwood number (A = 0.05) Rayleigh-Taylor mixing layer is performed using the tenth-order compact difference code Miranda. An initial multimode perturbation spectrum is specified in Fourier space as a function of mesh resolution such that a database of results is obtained in which each successive level of increased grid resolution corresponds approximately to one additional doubling of the mixing layer width, or generation. The database is then analyzed to determine approximate requirements for self-similarity, and a new metric is proposed to quantify how far a given simulation is from the limit of self-similarity. It is determined that mixing layer growth reaches a high degree of self-similarity after approximately 4.5 generations. Statistical convergence errors and boundary effects at late time, however, make it impossible to draw similar conclusions regarding the self-similar growth of more sensitive turbulence parameters. Finally, self-similar turbulence profiles from the LES database are compared with one-dimensional simulations using the k-L-a and BHR-2 Reynolds-averaged Navier-Stokes (RANS) models. The k-L-a model, which is calibrated to reproduce a quadratic turbulence kinetic energy profile for a self-similar mixing layer, is found to be in better agreement with the LES than BHR-2 results.

42 ENGINEERING↗

Inversion doublets of 3N+N cluster structure in excited states of {sup 4}He

Excited states of {sup 4}He are studied in four-body calculations with explicitly correlated Gaussian bases. All the levels below E{sub x}=26 MeV are reproduced reasonably well using realistic potentials. An analysis is made to show how the 0{sub 2}{sup +} state becomes a resonance but those having almost the same structure as this state in different spin-isospin channels are not observed as resonances. The role of tensor force is stressed with a particular attention to the level spacing between the two 0{sup -} states. The calculation of spectroscopic amplitudes, nucleon decay widths, and spin-dipole transition strengths demonstrates that the 0{sub 2}{sup +} state and the three lowest-lying negative-parity states with 0{sup -} and 2{sup -} have {sup 3}H+p and {sup 3}He+n cluster configurations, leading to the interpretation that these negative-parity states are the inversion-doublet partners of the 0{sub 2}{sup +} state.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Measurement of the mass and width of the Λ c ⁢(2625) + charmed baryon and the branching ratios of Λ c ⁢(2625) + → Σ$^{0}_{c}$π + and Λ c ⁢(2625) + → Σ$^{++}_{c}$π -

Using the entire data sample of 980 fb -1 collected at or near the Y⁡(4⁢S) resonance with the Belle detector operating at the KEKB asymmetric-energy e + ⁢e - collider, we report the measurement of the mass, width, and the branching ratios of the Λ c (2625) + charmed baryon. The mass difference between Λ c ⁢(2625) + and Λ$^{+}_{c}$ is measured to be M⁡(Λ c ⁢(2625) + )-M⁡(Λ$^{+}_{c}$)=341.518±0.006±0.049 MeV/c 2 . The upper limit on the width is measured to be Γ⁡(Λ c ⁢(2625) + )<0.52 MeV/c 2 at 90% confidence level. Based on a full Dalitz plot fit, branching ratios with respect to the mode Λ c⁢ (2625) + →Λ$^{+}_{c}$π + ⁢π - are measured to be $\frac{\mathscr{B}⁡(Λ_c(2625)^+ → Σ^{0}_{c}π^+)} {\mathscr{B}⁡(Λ_c(2625)^+ → ^{+}_{c}⁢π^+⁢π^-)}$ = (5.19±0.23±0.40)% and $\frac{\mathscr{B}(Λ_c (2625)^+ → Σ{_c^+}^+ π^-)}{\mathscr{B}(Λ_c (2625)^+ → Λ{_c^+} π^+π^-)}$ = (5.13±0.26±0.32)%, where the first and second uncertainties are statistical and systematic, respectively. These measurements can be used to further constrain the parameters of the underlying theoretical models.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Investigation of the Effect of In-Plane Fiber Waviness in Composite Materials through Multiple Scales of Testing and Finite Element Modeling

Defects in materials can reduce strengths and lifetimes of manufactured parts. The number of possible defects increases with the complexity inherent in composite materials. The wind industry uses composite wind turbine blades in which the manufacturing process induces a number of defects. In order for the wind industry to continue sustainable expansion, the effects of defects must be better understood. In-plane (IP) fiber waviness is the focus of this work. The three main parts of this work include testing on the coupon level, modeling on the coupon level, and testing of beams in four-point bending (with and without defects). The coupon level testing includes partial IP waves, similar to those in manufactured parts, rather than full width IP waves. This allows investigation into complex interactions and varying failure mechanisms caused by the fiber misalignment gradient. Partial waves are also modeled to both validate testing as well as to increase robustness of a previously developed progressive damage modeling method. Lastly, a sandwich beam test specimen for testing in 4-point bending is developed to investigate the effects of fiber waviness in both tension and compression when loaded in flexure.

36 MATERIALS SCIENCE↗

Plastic scintillation counters with an area of 2 sq m

Two designs of plastic scintillation counters with an area of 2 sq m scanned in each case by a single photomultiplier of the FEU-49 type are described. The radial dependence of their light collection at the place of the path of the detected particle does not exceed 10% while the half width of the differential distribution of the pulse amplitudes from nonfiltered cosmic radiation at sea level is 90 to 95%, and 65%, the plastic thickness being 5 cm and 10 cm, respectively. The temperature coefficient of the counter is 0.32% per 1 C.

Yegorov, T. A.↗

Ultraviolet spectrophotometry of Sirius from Gemini 12

The spectral energy distribution of Sirius between 2500 and 3700 A at a resolution of 7 A is obtained from plates taken on Gemini 12. The agreement with other observations and the most recent line-blanketed model atmospheres is good. The equivalent width of the Mg II doublet near 2800 A is 6.0 A, if the continuum level is represented by regions near 2650 and 2910 A. This is consistent with expectations for a hot Am star and implies line blocking of up to 15% in this wavelength region.

Spear, G. G.↗

Improved multispectral solar cell array

Solar-collector system projects oval-shaped color-band images onto solar cells designed to be most efficient at specific wavelength. Image size can be altered by changing width of reflecting mirror of power of lens. Image intensity is thus kept at optimum level, preventing cells from overheating.

Redmann, J. J.↗

Nonlinear axially symmetric circulations in a nearly inviscid atmosphere

The structure of certain axially symmetric circulations in a stably stratified, differentially heated, rotating Boussinesq fluid on a sphere is analyzed. A simple approximate theory (similar to that introduced by Schneider (1977)) is developed for the case in which the fluid is sufficiently inviscid that the poleward flow in the Hadley cell is nearly angular momentum conserving. The theory predicts the width of the Hadley cell, the total poleward heat flux, the latitude of the upper level jet in the zonal wind, and the distribution of surface easterlies and westerlies. Fundamental differences between such nearly inviscid circulations and the more commonly studied viscous axisymmetric flows are emphasized. The theory is checked against numerical solutions to the model equations.

Held, I. M.↗

Atmospheric temperature profiles and ray paths from occultation spectra

Simulated equivalent width data of weak lines in occultation spectra have been analyzed to retrieve both the atmospheric temperature profile and the tangent heights of the rays. The SNR of these widths varied from 5 to 100. The mixing ratio of the absorbing gas and sea level pressure were assumed but not the satellite position. Temperature and tangent heights with accuracies of 1 K and 0.25 km, respectively, were determined from lines with temperature-dependent and temperature-independent intensities.

Hoke, M. L.↗

Theoretical studies of important processes in planetary and comet atmospheres

Dissociative recombination (DR) reactions in planetary and comet atmospheres are discussed. A computer program was developed which determines DR cross sections and rates using potential curves and electronic capture widths. It uses Multi-Channel Quantum Defect Theory (MQDT) to include excited Rydberg resonance levels in the DR cross section and rate calculations. Each vibrational level of a molecular ion is the limit for an infinite series of Rydberg states. Above each ion vibrational level are Rydberg vibrational levels having higher ion levels as their series limit. These Rydberg vibrational levels are resonances, i.e., neutral states which are imbedded in the electron-molecular ion continuum. The process in which the Rydberg level causes an abrupt perturbation in the cross section for DR (because of interference between capture into the Rydberg level and capture into the repulsive dissociative state) is referred to as indirect recombination. The process in which the Rydberg levels are excluded and recombination goes from the entrance channel to the repulsive state is called direct recombination. The full DR process, i.e., both direct and indirect recombination, is the process of importance for planetary atmospheres. These ideas are illustrated with the new results for DR from excited ion vibrational levels of O2(+) into the dissociative state which leads to O(1S) + O(1D).

Guberman, Steven L.↗

Discrete/PWM Ballast-Resistor Controller

Circuit offers low switching loss and automatic compensation for failure of ballast resistor. Discrete/PWM ballast-resistor controller improved shunt voltage-regulator circuit designed to supply power from high-resistance source to low-impedance bus. Provides both coarse discrete voltage levels (by switching of ballast resistors) and continuous fine control of voltage via pulse-width modulation.

King, Roger J.↗

An Approach for Assessing Delamination Propagation Capabilities in Commercial Finite Element Codes

An approach for assessing the delamination propagation capabilities in commercial finite element codes is presented and demonstrated for one code. For this investigation, the Double Cantilever Beam (DCB) specimen and the Single Leg Bending (SLB) specimen were chosen for full three-dimensional finite element simulations. First, benchmark results were created for both specimens. Second, starting from an initially straight front, the delamination was allowed to propagate. Good agreement between the load-displacement relationship obtained from the propagation analysis results and the benchmark results could be achieved by selecting the appropriate input parameters. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Qualitatively, the delamination front computed for the DCB specimen did not take the shape of a curved front as expected. However, the analysis of the SLB specimen yielded a curved front as may be expected from the distribution of the energy release rate and the failure index across the width of the specimen. Overall, the results are encouraging but further assessment on a structural level is required.

Krueger, Ronald↗

An Approach to Assess Delamination Propagation Simulation Capabilities in Commercial Finite Element Codes

An approach for assessing the delamination propagation simulation capabilities in commercial finite element codes is presented and demonstrated. For this investigation, the Double Cantilever Beam (DCB) specimen and the Single Leg Bending (SLB) specimen were chosen for full three-dimensional finite element simulations. First, benchmark results were created for both specimens. Second, starting from an initially straight front, the delamination was allowed to propagate. The load-displacement relationship and the total strain energy obtained from the propagation analysis results and the benchmark results were compared and good agreements could be achieved by selecting the appropriate input parameters. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Qualitatively, the delamination front computed for the DCB specimen did not take the shape of a curved front as expected. However, the analysis of the SLB specimen yielded a curved front as was expected from the distribution of the energy release rate and the failure index across the width of the specimen. Overall, the results are encouraging but further assessment on a structural level is required.

Krueger, Ronald↗

An Approach for Assessing Delamination Propagation Capabilities in Commercial Finite Element Codes

An approach to assessing the delamination propagation capabilities in commercial finite element codes is presented and demonstrated for one code. For this investigation, the Double Cantilever Beam (DCB) specimen and the Single Leg Bending (SLB) specimen were chosen for full three-dimensional finite element simulations. First, benchmark results were created for both specimens. Second, starting from an initially straight front, the delamination was allowed to propagate. Good agreement between the load-displacement relationship obtained from the propagation analysis results and the benchmark results could be achieved by selecting the appropriate input parameters. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Qualitatively, the delamination front computed for the DCB specimen did not take the shape of a curved front as expected. However, the analysis of the SLB specimen yielded a curved front as may be expected from the distribution of the energy release rate and the failure index across the width of the specimen. Overall, the results are encouraging but further assessment on a structural level is required.

Krueger, Ronald↗

New techniques for determining spins and parities of neutron resonances and their impact on nuclear astrophysics

Here, we describe new techniques for determining spins and parities of neutron resonances which have resulted in large improvements over previous methods. These advances have made it possible, for the first time, to obtain reduced-neutron- and total-radiation-width distributions separately for resonances of different spin and parity in odd-A target nuclides. Using these new as well as previous data, we show that neutron distributions sometimes are significantly different from the Porter-Thomas distribution assumed by the nuclear statistical model. Furthermore, we show that the radiation-width distributions often are substantially different than predicted by the nuclear statistical model using standard level densities and photon strength functions. These differences could have significant impact on astrophysical reaction rates calculated using the statistical model.

79 ASTRONOMY AND ASTROPHYSICS↗

System and method for fissionable material detection with a short pulse neutron source

A system and method is disclosed for detecting fissionable materials. In one embodiment the system may incorporate a neutron pulse generator configured to generate multiple short pulses of neutrons, or a single pulse of sufficient intensity, in a vicinity of an object of interest. The source pulse of neutrons includes neutrons which each have a full width half maximum time duration of less than about 100 ns and a peak energy level no greater than about 20 MeV. A fast response detector is used which is able to detect single neutron events indicative of fission neutrons having been produced by the source pulse of neutrons interacting with fissionable material associated with the object of interest, and which arrive at the fast response detector within a predetermined time window immediately before arrival of the source neutron pulses.

Podpaly, Yuri↗

Anvil Tool in the Advanced Weather Interactive Processing System

Meteorologists from the 45th Weather Squadron (45 WS) and Spaceflight Meteorology Group (SMG) have identified anvil forecasting as one of their most challenging tasks when predicting the probability of violations of the lightning Launch Commit Criteria and Space Shuttle Flight Rules. As a result, the Applied Meteorology Unit (AMU) created a graphical overlay tool for the Meteorological Interactive Data Display Systems (MIDDS) to indicate the threat of thunderstorm anvil clouds, using either observed or model forecast winds as input. In order for the Anvil Tool to remain available to the meteorologists, the AMU was tasked to transition the tool to the Advanced Weather interactive Processing System (AWIPS). This report describes the work done by the AMU to develop the Anvil Tool for AWIPS to create a graphical overlay depicting the threat from thunderstorm anvil clouds. The AWIPS Anvil Tool is based on the previously deployed AMU MIDDS Anvil Tool. SMG and 45 WS forecasters have used the MIDDS Anvil Tool during launch and landing operations. SMG's primary weather analysis and display system is now AWIPS and the 45 WS has plans to replace MIDDS with AWIPS. The Anvil Tool creates a graphic that users can overlay on satellite or radar imagery to depict the potential location of thunderstorm anvils one, two, and three hours into the future. The locations are based on an average of the upper-level observed or forecasted winds. The graphic includes 10 and 20 nm standoff circles centered at the location of interest, in addition to one-, two-, and three-hour arcs in the upwind direction. The arcs extend outward across a 30 degree sector width based on a previous AMU study which determined thunderstorm anvils move in a direction plus or minus 15 degrees of the upper-level (300- to 150-mb) wind direction. This report briefly describes the history of the MIDDS Anvil Tool and then explains how the initial development of the AWIPS Anvil Tool was carried out. After testing was performed by SMG, 45 WS, and AMU, a number of needed improvements were identified. A bug report document was created that showed the status of each bug and desired improvement. This report lists the improvements that were made to increase the accuracy and user-friendliness of the tool. Final testing was carried out and documented and then the final version of the software and Users Guide was provided to SMG and the 45 WS. Several possible future improvements to the tool are identified that would increase the flexibility of the tool. This report contains a brief history of the development of the Anvil Tool in MIDDS, and then describes the transition and development of software to AWIPS.

Barrett, Joe, III↗