Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “JET MODEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

MULTIWAVELENGTH OBSERVATIONS OF A0620-00 IN QUIESCENCE

We present contemporaneous X-ray, ultraviolet, optical, near-infrared, and radio observations of the black hole binary system, A0620-00, acquired in 2010 March. Using the Cosmic Origins Spectrograph on the Hubble Space Telescope, we have obtained the first FUV spectrum of A0620-00 as well as NUV observations with the Space Telescope Imaging Spectrograph. The observed spectrum is flat in the FUV and very faint (with continuum fluxes {approx_equal} 1e - 17 erg cm{sup -2} s{sup -1} A{sup -1}). The UV spectra also show strong, broad (FWHM {approx} 2000 km s{sup -1}) emission lines of Si IV, C IV, He II, Fe II, and Mg II. The C IV doublet is anomalously weak compared to the other lines, which is consistent with the low carbon abundance seen in NIR spectra of the source. Comparison of these observations with previous NUV spectra of A0620-00 shows that the UV flux has varied by factors of 2-8 over several years. We compiled the dereddened, broadband spectral energy distribution (SED) of A0620-00 and compared it to previous SEDs as well as theoretical models. The SEDs show that the source varies at all wavelengths for which we have multiple samples. Contrary to previous observations, the optical-UV spectrum does not continue to drop to shorter wavelengths, but instead shows a recovery and an increasingly blue spectrum in the FUV. We created an optical-UV spectrum of A0620-00 with the donor star contribution removed. The non-stellar spectrum peaks at {approx_equal}3000 A. The peak can be fit with a T = 10,000 K blackbody with a small emitting area, probably originating in the hot spot where the accretion stream impacts the outer disk. However, one or more components in addition to the blackbody are needed to fit the FUV upturn and the red optical fluxes in the optical-UV spectrum. By comparing the mass accretion rate determined from the hot spot luminosity to the mean accretion rate inferred from the outburst history, we find that the latter is an order of magnitude smaller than the former, indicating that {approx}90% of the accreted mass must be lost from the system if the predictions of the disk instability model and the estimated interoutburst interval are correct. The mass accretion rate at the hot spot is 10{sup 5} the accretion rate at the black hole inferred from the X-ray luminosity. To reconcile these requires that outflows carry away virtually all of the accreted mass, a very low rate of mass transfer from the outer cold disk into the inner hot region, and/or radiatively inefficient accretion. We compared our broadband SED to two models of A0620-00 in quiescence: the advection-dominated accretion flow model and the maximally jet-dominated model. The comparison suggests that strong outflows may be present in the system, indicated by the discrepancies in accretion rates and the FUV upturn in flux in the SED.

79 ASTRONOMY AND ASTROPHYSICS↗

Coal and Biomass to Liquids (CBTL) Greenhouse Gas Optimization Tool Documentation

This report is the user documentation for the NETL CBTL Jet Fuel Model submitted under a separate approval routing. The documentation is intended to accompany the model. The documentation explains how to the use the model. The documentation does not contain any energy analysis findings. NETL completed this model/report as part of a study for the Connecticut Center for Advanced Technology (CCAT) to provide techno-economic and life cycle analysis modeling support for CBTL alternative jet fuel production, which forms key references to their report to the Defense Logistics Agency (their project sponsor/funder).

01 COAL, LIGNITE, AND PEAT↗

Preliminary Results of an Investigation at Transonic Speeds to Determine the Effects of a Heated Propulsive Jet on the Drag Characteristics of a Related Series of Afterbodies

Preliminary results are presented from an investigation to determine the influence of afterbody geometry on the effects of a sonic propulsive jet at transonic speeds. The results presented are base pressure coefficient and afterbody pressure-drag coefficient as a function of jet pressure ratio for different values of Mach number and jet temperature. Geometric parameters investigated include boattail angle, jet-to-model diameter ratio, and jet-to-base diameter ratio.

Henry, Beverly Z , Jr↗

Harnessing the Digital Transformation for Development of Electrified Aircraft Propulsion Control Systems

Hybrid electric aircraft propulsion is an emerging technology that presents a variety of potential benefits along with technical integration challenges. Developing these new propulsion architectures with their complex control systems, and ultimately proving their benefit, is a multistep process that goes from concept, to analysis, to dynamic simulation, to hardware in the loop testing, to full scale testing and beyond. This effort is being revolutionized and indeed enabled by new digital tools that support the increasing technology readiness level throughout the maturation process. NASA has developed and made available a suite of digital tools that ease the path from concept to implementation. The three packages are the Toolbox for the Modeling and Analysis of Thermodynamic Systems (T-MATS), the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), and the Thermal Systems Analysis Toolbox (TSAT). These tools are interactive, complementary, and compatible with each other. T-MATS is a modular thermodynamic modeling framework designed for creating custom component level models of jet engines. EMTAT is a modeling framework used to simulate a variety of power electronic devices, using both physics-based and power flow calculations. TSAT is a framework for modeling and analysis of dynamic heat transfer. These packages all consist of graphical, drag-and-drop, parameterizable building blocks representing various components of the system to be modeled, e.g., compressors, turbines, motors, energy storage devices, etc. They are designed to enable the user to model and simulate the end-to-end dynamic operation of a hybrid powertrain at the timescale of the turbomachinery, capturing mechanical, electrical, and thermal interactions. This paper will describe through multiple examples how these tools have been used successfully in several of the early stages of hybrid electric propulsion system development, from the initial system modeling to real-time interactive pilot-in-the-loop simulation to physical hardware-in-the-loop testing, each step bringing the technology closer to fruition.

Hybrid electric propulsion↗

Harnessing the Digital Transformation for Development of Hybrid Electric Aircraft Propulsion Control Systems

Hybrid electric aircraft propulsion is an emerging technology that presents a variety of potential benefits along with technical integration challenges. Developing these new propulsion architectures with their complex control systems, and ultimately proving their benefit, is a multistep process that goes from concept, to analysis, to dynamic simulation, to hardware in the loop testing, to full scale testing and beyond. This effort is being revolutionized and indeed enabled by new digital tools that support the increasing technology readiness level throughout the maturation process. NASA has developed and made available a suite of digital tools that ease the path from concept to implementation. The three packages are the Toolbox for the Modeling and Analysis of Thermodynamic Systems (T-MATS), the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), and the Thermal Systems Analysis Toolbox (TSAT). These tools are interactive, complementary, and compatible with each other. T-MATS is a modular thermodynamic modeling framework designed for creating custom component level models of jet engines. EMTAT is a modeling framework used to simulate a variety of power electronic devices, using both physics-based and power flow calculations. TSAT is a framework for modeling and analysis of dynamic heat transfer. These packages all consist of graphical, drag-and-drop, parameterizable building blocks representing various components of the system to be modeled, e.g., compressors, turbines, motors, energy storage devices, etc. They are designed to enable the user to model and simulate the end-to-end dynamic operation of a hybrid powertrain at the timescale of the turbomachinery, capturing mechanical, electrical, and thermal interactions. This paper will describe through multiple examples how these tools have been used successfully in several of the early stages of hybrid electric propulsion system development, from the initial system modeling to real-time interactive pilot-in-the-loop simulation to physical hardware-in-the-loop testing, each step bringing the technology closer to fruition.

Electrified Propulsion↗

Harnessing the Digital Transformation for Development of Electrified Aircraft Propulsion Control Systems

Hybrid electric aircraft propulsion is an emerging technology that presents a variety of potential benefits along with technical integration challenges. Developing these new propulsion architectures with their complex control systems, and ultimately proving their benefit, is a multistep process. This process includes concept development and analysis, dynamic simulation, hardware-in-the-loop testing, full-scale testing, and so on. This effort is being revolutionized and indeed enabled by new digital tools that support increasing the technology readiness level throughout the maturation process. As part of this Digital Transformation, NASA has developed a suite of publicly available digital tools that facilitate the path from concept to implementation. This paper describes the NASA-developed tools and puts them in the context of control system development for hybrid electric aircraft propulsion. The three MATLAB®-based software packages are the Toolbox for the Modeling and Analysis of Thermodynamic Systems (T-MATS), the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), and the Thermal Systems Analysis Toolbox (TSAT). These tools are interactive, complementary, and compatible with each other. T-MATS is a modular thermodynamic modeling framework designed for creating custom component level models of jet engines. EMTAT is a modeling framework used to simulate a variety of power electronic devices, using both physics-based and power flow calculations. TSAT is a framework for modeling and analysis of dynamic heat transfer. These packages all consist of graphical, drag-and-drop, parameterizable building blocks representing various components of the system to be modeled, e.g., compressors, turbines, motors, energy storage devices, etc. They are designed to enable the user to model and simulate the end-to-end dynamic operation of a hybrid electric gas turbine engine powertrain at the timescale of the turbomachinery, capturing mechanical, electrical, and thermal interactions. This paper demonstrates through multiple examples how these tools have been used successfully in a variety of applications, including several of the early stages of hybrid electric gas turbine engine propulsion system development, from the initial system modeling to real-time interactive pilot-in-the-loop simulation to physical hardware-in-the-loop testing, each step bringing the technology closer to fruition.

hybrid electric propulsion↗

Stellar and galactic jets - Theoretical issues

Theoretical issues pertaining to the modelling of jets in young stellar objects and in active galactic nuclei are reviewed. The strong morphological similarities between these two types of sources are emphasized, and observational constraints on the basic physical mechanisms that may be responsible for the jet phenomenon are outlined. Particular attention is given to the 'momentum-discharge problem' in molecular-cloud outflows and to its possible resolution in terms of a centrifugally driven magnetohydrodynamic wind from an accretion disk. In addition, various propagation effects are discussed, and the relevance to stellar jets of the de Laval collimation mechanism and of the accelerated-clump model for emission knots is assessed. The review concludes with a brief list of potentially useful observational tests.

Konigl, A.↗

Modeling the Restraint of Liquid Jets by Surface Tension in Microgravity

An axisymmetric phase field model is developed and used to model surface tension forces on liquid jets in microgravity. The previous work in this area is reviewed and a baseline drop tower experiment selected 'for model comparison. A mathematical model is developed which includes a free surface. a symmetric centerline and wall boundaries with given contact angles. The model is solved numerically with a compact fourth order stencil on a equally spaced axisymmetric grid. After grid convergence studies, a grid is selected and all drop tower tests modeled. Agreement was assessed by comparing predicted and measured free surface rise. Trend wise agreement is good but agreement in magnitude is only fair. Suspected sources of disagreement are suspected to be lack of a turbulence model and the existence of slosh baffles in the experiment which were not included in the model.

Chato, David J.↗

The role of electron-scale turbulence in the JET tokamak: experiments and modelling

Dedicated electron heat transport experiments have been carried out in L- and H-mode Deuterium plasmas of the JET-ILW tokamak to identify the amount of electron heat carried by electron-scale electron temperature gradient (ETG) modes. Ion cyclotron resonance heating at different positions has been used to probe the response of the electron temperature inverse gradient length R/L Te to changes in electron heat flux qe, while different amounts of neutral beam heating allowed to scan the ratio of ion to electron temperature T e /T i , which is a key parameter for the onset of ETGs. Results indicate a steepening of the normalized qe vs R/L Te curve above R/LT e ~ 8 for T e /T i ≤ 1, suggestive of the ETG onset. Ion-scale gyro-kinetic (GK) simulations match the ion heat flux and the low-R/L Te part of the qe curve, but do not reproduce such steepening at high R/L Te . Multi-scale GK simulations covering both ion and electron scales and including one impurity bundling light and heavy species indicate an ETG contribution only for R/L Te values larger than the experimental ones. Sensitivity studies of such result are difficult to achieve due to limitation in numerical resources. The quasi-linear TGLF model has been used for sensitivity studies. With the same bundled impurity as the GK multi-scale, TGLF shows the qe steepening at much larger R/L Te values than in experiment, but when using the real mix of light impurities neglecting the heavy impurities, TGLF gets closer to the experimental results. Profile simulations with TGLF including both light and heavy impurities show over-prediction of T e profiles and in some cases also of density, but good T i predictions, confirming issues with the model electron stiffness for these plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The flame structure and vorticity generated by a chemically reacting transverse jet

An analytical model describing the behavior of a turbulent fuel jet injected normally into a cross flow is developed. The model places particular emphasis on the contrarotating vortex pair associated with the jet, and predicts the flame length and shape based on entrainment of the oxidizer by the fuel jet. Effects of buoyancy and density variations in the flame are neglected in order to isolate the effects of large-scale mixing. The results are compared with a simulation of the transverse reacting jet in a liquid (acid-base) system. For a wide range of ratios of the cross flow to jet velocity, the model predicts flame length quite well. In particular, the observed transitional behavior in the flame length between cross-flow velocity to jet velocity of orifice ratios of 0.0 to 0.1, yielding an approximate minimum at the ratio 0.05, is reproduced very clearly by the present model. The transformation in flow structure that accounts for this minimum arises from the differing components of vorticity dominant in the near-field and far-field regions of the jet.

Karagozian, A. R.↗

The Composition of GRB Jets and the ICMART Model

Models of gamma ray bursts (GRBs) are drawn from observations of light curves, spectra, and spectral evolution. The ICMART (Internal Collision-induced MAgnetic Reconnection & Turbulence) model and some of its features are presented. Increasing evidence points towards Poynting-flux-dominated jets in at least some (even a good fraction of) GRBs. The main emission component (Band) is of a synchrotron emission origin, produced by electrons accelerated in the emission region. The data seem to require that magnetic reconnection in the moderately-high sigma regime is the mechanism to accelerate particles. Extensive numerical simulations are needed to verify physical details of such a model, and some encouraging results have been obtained.

79 ASTRONOMY AND ASTROPHYSICS↗

Evaluation of stochastic particle dispersion modeling in turbulent round jets

ODT (one-dimensional turbulence) simulations of particle-carrier gas interactions are performed in the jet flow configuration. Particles with different diameters are injected onto the centerline of a turbulent air jet. The particles are passive and do not impact the fluid phase. Their radial dispersion and axial velocities are obtained as functions of axial position. The time and length scales of the jet are varied through control of the jet exit velocity and nozzle diameter. Dispersion data at long times of flight for the nozzle diameter (7 mm), particle diameters (60 and 90 µm), and Reynolds numbers (10, 000–30, 000) are analyzed to obtain the Lagrangian particle dispersivity. Flow statistics of the ODT particle model are compared to experimental measurements. It is shown that the particle tracking method is capable of yielding Lagrangian prediction of the dispersive transport of particles in a round jet. In this study, three particle-eddy interaction models (Type-I, -C, and -IC) are presented to examine the details of particle dispersion and particle-eddy interaction in jet flow.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Three-dimensional compressible jet-in-crossflow calculations using improved viscosity models and adapted grid

Previous calculations of jet-in-crossflow problems have been sensitive to the turbulence and artificial viscosity models and to the grid. Consequently, the eddy viscosity model in the PARC3D code was modified to consider the turbulent jet by switching from the Baldwin-Lomax (1978) model to an axisymmetric jet model. A modified artificial viscosity model has been utilized and evaluated in this study as well. The new model includes cell size scaling and a directional dependence in the coefficients. Computational results from PARC3D demonstrate the effects of the viscosity models on the pressure distribution fore and aft of the jet and the ability of the adaptive grid scheme to adjust to the three-dimensional gradients around the jet.

Lytle, John K.↗

Application of Time-resolved PIV to Supersonic Hot Jets

This presentation lays out the ground-breaking work at bringing high-speed (25kHz) particle image velocimetry (PIV) to bear on measurements of noise-producing turbulence in hot jets. The work is still in progress in that the tremendous amount of data obtained are still be analyzed, but the method has been validated and initial results of interest to jet noise modeling have been obtained. After a brief demonstration of the validation process used on the data, results are shown for hot jets at different temperatures and Mach numbers. Comparisons of first order statistics show the relative indifference of the turbulence to the presence of shocks and independence to jet temperature. What does come out is that when the shock-containing jets are in a screech mode the turbulence is highly elevated, showing the importance of removing screech phenomena from model-scale jets before applying findings to full-scale aircraft which typically do not contain shocks.

Bridges, James↗

Attached and Attaching Three-Dimensional Jets from Circular Nozzles: Analytical Model

Here we evaluate velocity profiles of three dimensional attached jets emerging from circular nozzles. These jets lose momentum due to interactions with nearby surfaces and are important to evaluating flows in mixing vessels and to suspending solids and trapped gases in radioactive waste tanks. Despite the industrial importance of attached jets, simple, complete, and quantitative expressions for their velocity profiles remain elusive. Here we present a quantitative analytical model of the three dimensional velocity profiles of attached jets inclusive of a local skin coefficient of friction. We compare these expressions to experimental velocity profiles at moderate and high nozzle Reynolds numbers to find reasonable quantitative agreement.

Jet, attached jet, offset jet, reattaching offset ↗