Radiation effects on silicon Final report, Jun. 1, 1964 - May 31, 1965
Radiation effects on silicon - degradation of carrier lifetime in N and P type silicon samples exposed to 30 MeV electron irradiation
SILICON↗
SEARCH · Engineering Papers
Results for “Irradiation defect”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Production of disordered regions in germanium by electron irradiation.
Disordered regions and energy level position in germanium produced by electron irradiation
CRYSTAL STRUCTURE DEFECT↗
A detailed study of the photo-injection annealing of thermally diffused InP solar cells
A detailed analysis of the annealing of thermally diffused InP solar cells fabricated by the Nippon Mining Co. is presented. The cells were irradiated with 1 MeV electrons, and the induced degradation is measured using deep level transient spectroscopy and low temperature (86 K) IV measurements. Clear recovery of the photovoltaic parameters is observed during low temperature (T is less than 300 K) solar illuminations (1 sun, AMO) with further recovery at higher temperatures (300 less than T less than 500 K). For example, the output of a cell which was irradiated up to a fluence of 1 x 10(exp 16) cm(sup -2) was observed to recover to within 5 percent of the pre-irradiation output. An apparent correlation between the recovery of I(sub sc) and the annealing of the H4 defect and of the minority carrier trapping centers is observed. An apparent correlation between the recovery of VO, and the annealing of the H5 defect is also observed. These apparent correlations are used to develop a possible model for the mechanism of the recovery of the solar cells.
Walters, R. J.↗
InP- and GaAs-Based 0.6 eV GaInAs Devices for Thermophotovoltaics and Laser Power Conversion
Emerging applications such as thermal energy grid storage, waste heat recovery and portable power generation require efficient thermophotovoltaic (TPV) converters tuned to temperatures near 1000 Degrees Celsius or below. Metamorphic GaInAs with larger lattice constants than InP present a promising option for these needs. The ability to grow these devices on GaAs substrates instead of more expensive InP would enhance the scalability of these devices. In this talk, we present inverted metamorphic Ga0.3In0.7As photovoltaic converters with sub-0.60 eV bandgaps grown on InP and GaAs substrates. These devices are realized using InAsP or GaInP/InAsP compositionally graded buffers which exhibit threading dislocation densities of 1.3 +/- 0.6 x 106 cm-2 and 8.9 +/- 1.7 x 106 cm-2 on InP and GaAs, respectively. Despite this difference in defect density, the devices generate similar open-circuit voltages of 0.386 V and 0.383 V, respectively, under irradiance producing a short-circuit current density of -10 A/cm2, with bandgap-voltage offsets of 0.20 and 0.21 V. We estimate their thermophotovoltaic efficiency using these measurements coupled with broadband reflectance measurments. The InP-based cell is estimated to yield 1.09 W/cm2 at 1100 Degrees Celsius vs. 0.92 W/cm2 for the GaAs-based cell, with TPV efficiencies of 16.8 vs. 9.2%. Both devices are limited by sub-bandgap absorption, which we assess largely occurs in the graded buffers. We estimate that the 1100 Degrees Celsius thermophotovoltaic efficiencies would increase to 24.0% and 20.7% in structures with the graded buffer removed, if previously demonstrated reflectance is achieved. These devices also have application as laser power converters in the 2.0-2.3 um atmospheric window. We estimate efficiencies of 36.8% and 32.5% under 2.0 um monochromatic irradiance of 1.86 W/cm2 and 2.81 W/cm2, respectively.
ENGINEERING,MATERIALS SCIENCE,SOLAR ENERGY↗
Quantitative assessment of Ni + and He + ion irradiation damage in a tungsten heavy alloy under the simulated nuclear fusion environment
A 90W-7Ni-3Fe (wt.%) tungsten heavy alloy has been sequentially Ni + and He + ion irradiated at 700 °C to simulate the high temperature irradiation environment of a fusion reactor interior. W/Ni–Fe-W dual-phase alloys have been proposed to serve as plasma facing materials and require detailed investigation of their behavior under fusion relevant conditions to assess their overall applicability. To evaluate material performance under five years of simulated fusion reactor service, microstructural characterization of the nanoscale defect distribution has been performed on both constituent phases, revealing peak swelling in the W phase of approximately 0.03%. The γ-phase (Ni–Fe-W) is found to swell approximately 0.68% under the same irradiation conditions, indicating significant cavity formation and growth. Additionally, a novel multi-projection imaging approach has been applied to determine the extent of damage segregation along the dual-phase W-to-γ interface and exposes that these interfaces act as sink sites for the accumulation of cavities. Interphase boundaries are noted to possess an 11.8% areal coverage of defects along the boundary plane, primarily on the γ-phase side of the boundary. The accumulation of cavities at these interphase boundaries is anticipated to adversely affect overall material toughness, and this work reveals a pressing need for mechanical property testing of irradiated W–Ni-Fe dual-phase alloys.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Helium co-implantation effects on dislocation loop evolution during in situ ion irradiations of a novel additive-manufactured Fe-9Cr steel alloy
This study examines the impact of helium injection rate on dislocation loop evolution during ion irradiation of a novel, additively manufactured (AM) 9Cr reduced-activation ferritic/martensitic (RAFM) steel. Through in situ transmission electron microscopy ion irradiations and post-irradiation characterization, the effects of simultaneous 1 MeV Kr²⁺ and 12 keV He⁺ ion irradiation at 400°C to 5 dpa with varying helium levels were examined. The findings reveal that helium co-injection significantly increases dislocation loop density, primarily through the formation of small defect features exhibiting contrast and projected morphologies consistent with a⟨100⟩ loops (∼1 nm), while suppressing larger a/2⟨111⟩ loops. The findings underscore the complex interplay among continuously increasing helium content, temperature, and alloy composition in the evolution of dislocation loops under irradiation in RAFM steels. The study highlights the need for further investigation into helium-mediated mechanisms, such as proposed interactions between self-interstitial atoms and helium atoms, to enhance the performance of RAFM steels in advanced nuclear reactors.
ANA2↗
Chromosomal Aberrations in DNA Repair Defective Cell Lines: Comparisons of Dose Rate and Radiation Quality
Chromosome aberration yields were assessed in DNA double-strand break repair (DSB) deficient cells after acute doses of gamma-rays or high-LET iron nuclei, or low dose-rate (0.018 Gy/hr) gamma-rays. We studied several cell lines including fibroblasts deficient in ATM (product of the gene that is mutated in ataxia telangiectasia patients) or NBS (product of the gene mutated in the Nijmegen breakage syndrome), and gliomablastoma cells that are proficient or lacking in DNA-dependent protein kinase, DNA-PK activity. Chromosomes were analyzed using the fluorescence in-situ hybridization (FISH) chromosome painting method in cells at the first division post-irradiation and chromosome aberrations were identified as either simple exchanges (translocations and dicentrics) or complex exchanges (involving >2 breaks in 2 or more chromosomes). Gamma radiation induced higher yields of both simple and complex exchanges in the DSB repair defective cells than in the normal cells. The quadratic dose-response terms for both chromosome exchange types were significantly higher for the ATM and NBS defective lines than for normal fibroblasts. However, the linear dose-response term was significantly higher only for simple exchanges in the NBS cells. Large increases in the quadratic dose response terms indicate the important roles of ATM and NBS in chromatin modifications that facilitate correct DSB repair and minimize aberration formation. Differences in the response of AT and NBS deficient cells at lower doses suggests important questions about the applicability of observations of radiation sensitivity at high dose to low dose exposures. For all iron nuclei irradiated cells, regression models preferred purely linear and quadratic dose responses for simple and complex exchanges, respectively. All the DNA repair defective cell lines had lower Relative biological effectiveness (RBE) values than normal cells, the lowest being for the DNA-PK-deficient cells, which was near unity. To further investigate the sensitivity differences for low and low high doses, we performed chronic low dose-rate irradiation, and have begun studies with ATM and Nibrin inhibitors and siRNA knockout of these proteins. Results support the conclusion that for the endpoint of simple chromosomal aberrations (translocation or dicentrics), the increased radiation sensitivity of AT cells found at high doses (>1 Gy) does not carry over to low doses or doserates, while NBS cells show increased sensitivity for both high and low dose exposures.
George, K. A.↗
Probing the Damage Recovery Mechanism in Irradiated Stainless Steels Using In-Situ Microcantilever Bending Test
Single crystalline microcantilevers are fabricated from the base metal and heat-affected zone (HAZ) of a laser welded, neutron irradiated austenitic stainless steel, for scanning electron microscope (SEM) in-situ bending. In the HAZ, cantilevers exhibit higher yield point and lower crack tip blunting displacement than in the base metal and unirradiated archive specimen. These results suggest that radiation-induced defects harden the base metal, whereas the HAZ exhibits annealing of defects leading to mechanical softening. Dislocation nucleation ahead of the crack tip is responsible for ductile blunting behavior and provides a pathway to mitigating helium-induced cracking during weld repairs of irradiated materials.
36 MATERIALS SCIENCE↗
Ion-beam radiation-induced Eshelby transformations: The mean and variance in hydrostatic and shear residual stresses
Ion beam plays a pivotal role in ion implantations and the fabrication of nanostructures. However, there lacks a quantitative model to describe the residual stresses associated with the ion-beam radiation. Radiation-induced residual stress/transformation strain have been mostly recognized in the hydrostatic sub strain space. Here, in this study, we use molecular dynamics (MD) simulations to show that the response of a material to irradiation is generally anisotropic that depends on the ion-beam direction, and should be described using tensorial quantities. We demonstrate that accelerator-based ion beam irradiation, combined with the intrinsic lattice anisotropy and externally induced anisotropy (such as anisotropic mechanical loadings), causes radiation-actuated shear transformation strains in addition to hydrostatic expansion. We map out these complex correlations for several materials. Radiation-induced defects are shown to be responsible for residual shear stresses in the manner of Eshelby inclusion transformation. We propose such tensorial response model should be considered for accurate nanoscale fabrication using ion-beam irradiation.
46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
Irradiation Creep in Materials
A knowledge of the dimensional stability of reactor structural components, under irradiation conditions, is of major importance in the design of thermal, fast, and fusion reactors. When subjected to simultaneous mechanical loading and irradiation, structural materials exhibit a visco-plastic deformation phenomenon, referred to as irradiation creep, which can be more rapid than the deformation occurring out of irradiation. In this article, the phenomenology of this peculiar behavior is described after a short history of its discovery. Then, the theoretical mechanisms proposed in the literature during these past 60 years are presented, with a special focus on mechanisms based on stress induced preferred absorption of point defects by dislocation loops, dislocations and grain boundaries and on mechanisms based on climb-enhanced glide of dislocations. These mechanisms are discussed in the light of experimental evidences. Finally, irradiation creep in various materials, such as zirconium alloys, austenitic stainless steels, nickel-based alloys, ferritic-martensitic steels and graphite, is described.
Onimus, Fabien↗
Microstructural and compositional evolutions in $γ$-LiAlO 2 pellets during ion irradiation at an elevated temperature
This study reports on the microstructural, phasic and compositional evolutions of γ-LiAlO 2 during ion irradiation. Polycrystalline γ-LiAlO 2 pellets were irradiated sequentially with He + and D 2 + ions to the same combined fluences of up to 3 × 10 17 (He + +D + )/cm 2 at 773 K. The irradiated pellets were characterized using scanning transmission electron microscopy and atom probe tomography. Surface amorphization likely due to radiolysis and planar defects as a possible precursor for formation of precipitates are created at 5 × 10 16 (He + +D + )/cm 2 , followed by the formation of nano-sized precipitates and fractures at higher doses. Spinel-like precipitates of non-stoichiometric LiAl 5 O 8 and gas-filled cavities are observed to grow with increasing dose. Faceted precipitates and rounded cavities appear at 2 × 10 17 (He + +D + )/cm 2 . With further increasing ion fluence to 3 × 10 17 (He + +D + )/cm 2 , amorphization of the precipitates takes place and micron-sized fractures appear. Surface exfoliation could occur at an extremely high ion fluence. There are compositional changes in the γ-LiAlO 2 pellets during the microstructural evolution. In the precipitate and amorphized regions, Li concentrations decrease to ~7 and 3.7 at.% from 25 at.% in γ-LiAlO 2 , respectively. This study reveals a full-cycle microstructural evolution with corresponding compositional changes in γ-LiAlO 2 pellets during ion irradiation at 773 K. In conclusion, the data could help model, assess, and predict the material performance during neutron irradiation in reactors.
73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
Cluster dynamics modeling of irradiation growth in single crystal Zr
Irradiation growth of single-crystal Zr is modeled with a reduced set of cluster dynamics equations. Nucleation and growth of basal and prismatic dislocation loops are both accounted for in the model. Equations are developed for the time evolution of single point defects, a limited number of point defect clusters, interstitial and vacancy loop nucleation rates, as well as for the growth of vacancy loops on basal planes and interstitial loops on prismatic planes. Reduction of the usual infinite hierarchy of cluster dynamics equations to the simple set studied here is justified on the physical basis of the stability of small loops once nucleated. This simplified cluster dynamics model with a small number of adjustable parameters avoids the complexity of explicit representation of higher order point defect clusters. The model shows consistency with experimental observations of the following aspects: (1) the growth rates of Zr crystals along the a- and c-axes; (2) the onset dose for breakaway irradiation growth; (3) the saturation dislocation loop densities of vacancy and interstitial loops; (4) the effects of cold work and temperature on irradiation growth.
36 MATERIALS SCIENCE↗
Microstructure and hardness evolution induced by annealing of ion irradiated LiTaO 3
We report the evolution of the microstructure and mechanical properties of low-energy heavy-ion-irradiated LiTaO 3 crystals annealed at various temperatures was investigated by transmission electron microscopy (TEM) observations and nanoindentation tests to extend the applications of irradiated LiTaO 3 crystals. Before annealing, randomly distributed voids formed in an approximately 200 nm thick region at the end of the ion irradiation range, which was attributed to preferential absorption of interstitials by the amorphous-crystalline interface. After annealing, a new directional diffusion path of defects was identified, resulting in a void string. Furthermore, void string diffusion to the free surface was also found during the annealing temperature increase process, which offers a potential application in designing custom sized-thickness exfoliation at the nanoscale. Meanwhile, two competing processes were identified during the annealing process: epitaxial recrystallization from the amorphous-crystalline interface and grain nucleation process in the amorphous region, which formed phases different from the matrix crystal structure, resulting in an interaction between them. Furthermore, the hardness of irradiated samples was also found to be affected by the annealing process; in particular, a hardness decrease induced by the interstitial Fe ions in the recrystallized region was also confirmed, which can improve the processability of samples for further application.
36 MATERIALS SCIENCE↗
Irradiation enhanced diffusion and diffusional creep in U₃Si₂
U₃Si₂ is a candidate as an advanced fuel for light water reactors (LWRs). Compared to UO₂, there are significant data gaps for the thermophysical and thermomechanical properties of U₃Si₂. Atomic scale simulations can help fill in those gaps, while also providing a more mechanistic understanding of the material properties. Creep is an important property for fuel performance as it influences the pellet-cladding gap, which in turn affects the temperature of the fuel (a key parameter in many other aspects of fuel behavior). In this work, we employed a DFT-informed cluster dynamics framework to predict point defect concentrations in U₃Si₂. The concentrations, diffusivities, and volumes of these defects were used to develop a diffusional creep model based on bulk (Nabarro-Herring) and grain boundary (Coble) diffusion processes. It was found that irradiation enhanced Nabarro-Herring creep is dominant at low temperatures, while Coble creep dominates for high temperatures. The model compares well against available experimental data and has been implemented in BISON. A demonstration case using simple power profiles has been carried out, showing that negligible creep occurs due to the low temperatures experienced by U₃Si₂, a consequence of its high thermal conductivity.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
The role of UC inclusions in the development of fission gas bubble superlattice neutron-irradiated monolithic U-10Mo fuels
Uranium Carbide (UC) inclusions are the most prevalent impurities in Uranium-Molybdenum (U-Mo) fuel and are considered undesirable because they could potentially affect fuel performance. This work revealed that, like grain boundaries (gBs), UC inclusions could help facilitate the formation of the fission gas bubble superlattice (GBS). The GBS is a highly organized complex defect structure that can effectively store fission gases, thereby inhibiting fuel swelling. Transmission electron microscopy (TEM) showed that GBS self-organization can initiate at the UC/U-Mo interfaces in U-10Mo fuel irradiated to low fission density. Furthermore, this study also revealed that the UC boundary in U-10Mo irradiated to low fission density is wavy and periodic in morphology and that GBS formation is semi-coherent with the UC boundary. Because the initiation of GBS occurs at gBs and UC/U-Mo interfaces, the fission gas inventory is always highest at those regions compared to the U-Mo grain interior. Consequently, at higher fission densities, it is likely that high burnup structure (HBS) development via grain refinement will begin at gBs and UC/U-Mo interfaces.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Study of SEM induced current and voltage contrast modes to assess semiconductor reliability
The purpose of the scanning electron microscopy study was to review the failure history of existing integrated circuit technologies to identify predominant failure mechanisms, and to evaluate the feasibility of their detection using SEM application techniques. The study investigated the effects of E-beam irradiation damage and contamination deposition rates; developed the necessary methods for applying the techniques to the detection of latent defects and weaknesses in integrated circuits; and made recommendations for applying the techniques.
Beall, J. R.↗
Tritium diffusion and formation in the bulk and defective surface of γ-LiAlO2 pellets: First-principles investigation
In tritium-producing burnable absorber rods (TPBAR), γ-LiAlO2 is used in the form of an annular ceramic pellet enriched with the 6Li isotope. When irradiated in a pressurized water reactor (PWR), the <sup>6</sup>Li pellets absorb neutrons and produce tritium (<sup>3</sup>H) through <sup>6</sup>Li + n <sup>3</sup>H + α. The 3H chemically reacts with the metal getter where it is captured and leads to formation of a metal hydride. For TPBARs to enable effective tritium production in PWRs, we investigated the <sup>3</sup>H diffusion pathways in the bulk and surface of γ-LiAlO<sub>2</sub> with different concentrations of lithium defects. The calculated results for bulk and low-index surfaces, thermal conductivity, 3H activation energy barriers, and the 3H diffusion coefficients in γ-LiAlO<sub>2</sub> are in good agreement with the available experimental values. In the bulk, our results show that the smallest activation energy barrier is 0.63 eV for substitutional <sup>3</sup>H diffusion with a diffusion coefficient of 3.25x10<sup>-12</sup> m<sup>2</sup>/s. After <sup>3</sup>H diffused from bulk to the surface, it could form different species (such as <sup>3</sup>H<sub>2</sub>, <sup>3</sup>H<sub>2</sub>O, C<sup>3</sup>H<sub>4</sub>) depending on the surface structure, vacancy types and the impurity carbon. Our results indicate that the <sup>3</sup>H<sub>2</sub> is the main product from γ-LiAlO<sub>2</sub> pellets. As the number of V<sub>Li</sub> vacancies and <sup>3</sup>H atoms increases under irradiation (<sup>3</sup>H-rich condition), <sup>3</sup>H<sub>2</sub>O release could increase from the surface of γ-LiAlO<sub>2</sub> pellets.
Jia, Ting↗
A Rate Theory Model of Radiation-Induced Swelling in an Austenitic Stainless Steel
Many rate theory models of cavity (void) swelling have been published over the past 50 years, all having the same, or similar, structures. A rigorous validation of the models has not been possible because of the dearth of information concerning the microstructures that correspond with the swelling data. Whereas the lack of microstructure information is still an issue for historical swelling data, in the past 10–20 years data have been published on the evolution of the microstructure (point defect yields from collision cascades, cavity number densities, and dislocation densities/yield strengths) allowing certain gaps in information to be filled when considering historic swelling data. With reasonable estimates of key microstructure parameters, a standard rate theory model can be applied, and the model parameter space explored, in connection with historical swelling data. By using published data on: (i) yield strength as a function of dose and temperature (to establish an empirical expression for dislocation density evolution); (ii) cavity number densities as a function of temperature; and (iii) freely migrating defect (FMD) production as a function of primary knock-on atom (PKA) spectrum, the necessary parameter and microstructure inputs that were previously unknown can be used in model development. This paper describes a rate-theory model for void swelling of 316 stainless steel irradiated in the EBR-2 reactor as a function of irradiation temperature and neutron dose.
36 MATERIALS SCIENCE↗