Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “High”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Fabrication of very-low-density, high-stiffness carbon fiber/aluminum hybridized composite with ultra-low density and high stiffness (M-11)

Fabrication of a composite material with ultra-low density and high stiffness in microgravity is the objective of the investigation. The composite structure to be obtained is a random three-dimensional array of high modulus, short carbon fibers bonded at contact points by an aluminum alloy coated on the fibers. The material is highly porous and thus has a very low density. The motivation toward the investigation, simulation experiments, choice of the component materials, and on-flight experiment during ballistic trajectory of a NASDA rocket, are described.

Suzuki, Tomoo↗
NASA NTRS1995

Edge technique lidar for high accuracy, high spatial resolution wind measurement in the Planetary Boundary Layer

The goal of the Army Research Office (ARO) Geosciences Program is to measure the three dimensional wind field in the planetary boundary layer (PBL) over a measurement volume with a 50 meter spatial resolution and with measurement accuracies of the order of 20 cm/sec. The objective of this work is to develop and evaluate a high vertical resolution lidar experiment using the edge technique for high accuracy measurement of the atmospheric wind field to meet the ARO requirements. This experiment allows the powerful capabilities of the edge technique to be quantitatively evaluated. In the edge technique, a laser is located on the steep slope of a high resolution spectral filter. This produces large changes in measured signal for small Doppler shifts. A differential frequency technique renders the Doppler shift measurement insensitive to both laser and filter frequency jitter and drift. The measurement is also relatively insensitive to the laser spectral width for widths less than the width of the edge filter. Thus, the goal is to develop a system which will yield a substantial improvement in the state of the art of wind profile measurement in terms of both vertical resolution and accuracy and which will provide a unique capability for atmospheric wind studies.

Korb, C. L.↗
NASA NTRS1961

Static Longitudinal Characteristics at High Subsonic Speeds of a Complete Airplane Model with a Highly Tapered Wing having the 0.80 Chord Line Unswept and with Several Tail Configurations

An investigation was made at high subsonic speeds of a complete model having a highly tapered wing and several tail configurations. The basic aspect-ratio-4.00 wing had zero taper and an unswept 0.80 chord line. Several aspect-ratio modifications to the basic wing were made by clipping off portions of the wing tips. The complete model was tested with a chord-plane tail, a T-tail, and a biplane tail (combined T-tail and chord-plane tail). The model was tested in the Langley high-speed 7- by 10-foot tunnel at Mach numbers from 0.60 to 0.92. The data show that, when reduced to the same static margin, all the tail configurations tested on the model provided fairly good stability characteristics, the biplane tail giving the.best overall characteristics as regards pitching-moment linearity. Changes in static margin at zero lift coefficient with Mach number were small for the model with these tails over the Mach number range investigated.

Goodson, Kenneth W.↗
NASA NTRS1940

Investigation of the Characteristics of a High-Aspect-Ratio Wing in the Langley 8-Foot High-Speed Tunnel

An investigation of the characteristics of a wing with an aspect ratio of 9.0 and an NACA 65-210 airfoil section has been made at Mach number up to 0.925. The wing tested has a taper ratio of 2.5:1.0, no twist, dihedral, or sweepback, and 20-percent - chord 37.5-percent-semispan plain ailerons. The results showed that serious changes in the normal-force characteristics occurred when the Mach number was increased above 0.74 at angles of attack between 4 deg. and 10 deg. and above 0.80 at 0 deg. angle of attack.Because of small outboard shifts in the lateral center of load, the bending moment at the root for conditions corresponding to a 3g pull-out at an altitude of 35,000 feet increased by approximately 5% when the Much number was increased beyond 0.83 the negative pitching moments for the high angles of attack increased, whereas those for the low angles of attack decreased with a resulting large increase in the negative slope of the pitching-moment curves. A large increase occurred in the values of the drag coefficients for the range of lift coefficients needed for level flight at an altitude of 35,000 feet when the Mach number was increased beyond a value of 0.80. The wakes at a station 2.82 root chords behind the wing quarter-chord line extended approximately a chord above the wing chord line for the angles of attack required to recover from high-speed dives at high Mach numbers.

Whitcomb, Richard T.↗
NASA NTRS1961

Investigation at High Subsonic Speeds of the Use of Low Auxiliary Tail Surfaces having Dihedral to Improve the Longitudinal and Directional Stability of a T-Tail Model at High Lift

An investigation of the use of low auxiliary horizontal-tail surfaces to alleviate the pitch-up tendency at high lift of an airplane configuration having a T - tail has been conducted in the Langley high-speed 7- by 10-foot tunnel. The basic model had a wing with an aspect ratio of 3, a taper ratio of 0.143, and an unswept 80-percent chord line. The Mach number for most of the tests extended from 0.60 to 0.94 and the angle-of-attack range was from -2 deg. to approximately 24 deg. at the lowest test Mach number. A preliminary study of a systematic series of auxiliary tails indicated that the pitch-up tendency at high lift encountered on the basic model could be greatly alleviated by use of a relatively small, very low-aspect-ratio auxiliary horizontal tail. This tail was located radially with respect to the fuselage center line with 30 deg. negative dihedral and therefore provided a significant favorable increment to directional stability of the model throughout most of the test angle-of-attack range.

Sleeman, William C., Jr.↗
NASA NTRS2004

Development and Characterization of High-Efficiency, High-Specific Impulse Xenon Hall Thrusters

This dissertation presents research aimed at extending the efficient operation of 1600 s specific impulse Hall thruster technology to the 2000 to 3000 s range. Motivated by previous industry efforts and mission studies, the aim of this research was to develop and characterize xenon Hall thrusters capable of both high-specific impulse and high-efficiency operation. During the development phase, the laboratory-model NASA 173M Hall thrusters were designed and their performance and plasma characteristics were evaluated. Experiments with the NASA-173M version 1 (v1) validated the plasma lens magnetic field design. Experiments with the NASA 173M version 2 (v2) showed there was a minimum current density and optimum magnetic field topography at which efficiency monotonically increased with voltage. Comparison of the thrusters showed that efficiency can be optimized for specific impulse by varying the plasma lens. During the characterization phase, additional plasma properties of the NASA 173Mv2 were measured and a performance model was derived. Results from the model and experimental data showed how efficient operation at high-specific impulse was enabled through regulation of the electron current with the magnetic field. The electron Hall parameter was approximately constant with voltage, which confirmed efficient operation can be realized only over a limited range of Hall parameters.

Hofer, Richard R.↗
NASA NTRS2004

High Altitude Radiations Relevant to the High Speed Civil Transport (HSCT)

The Langley Research Center (LaRC) performed atmospheric radiation studies under the SST development program in which important ionizing radiation components were measured and extended by calculations to develop the existing atmospheric ionizing radiation (AIR) model. In that program the measured neutron spectrum was limited to less than 10 MeV by the available 1960-1970 instrumentation. Extension of the neutron spectrum to high energies was made using the LaRC PROPER-3C monte carlo code. It was found that the atmospheric neutrons contributed about half of the dose equivalent and approximately half of the neutron contribution was from high energy neutrons above 10 MeV. Furthermore, monte carlo calculations of solar particle events showed that potential exposures as large as 10-100 mSv/hr may occur on important high latitude routes but acceptable levels of exposure could be obtained if timely descent to subsonic altitudes could be made. The principal concern was for pregnant occupants onboard the aircraft. As a result of these studies the FAA Advisory Committee on the Radiobiological Aspects of the SST recommended: 1. Crew members will have to be informed of their exposure levels 2. Maximum exposures on any flight to be limited to 5 mSv 3. Airborne radiation detection devices for total exposure and exposure rates 4. Satellite monitoring system to provide SST aircraft real-time information on atmospheric radiation levels for exposure mitigation 5. A solar forecasting system to warn flight operations of an impending solar event for flight scheduling and alert status. These recommendations are a reasonable starting point to requirements for the HSCT with some modification reflecting new standards of protection as a result of changing risk coefficients.

Wilson, J. W.↗
NASA NTRS2001

Comparison of F ratios generated from interphase and metaphase chromosome damage induced by high doses of low- and high-LET radiation

Although biophysical models predict a difference in the ratio of interchromosomal to intrachromosomal interarm exchanges (F ratio) for low- and high-LET radiations, few experimental data support this prediction. However, the F ratios in experiments to date have been generated using data on chromosome aberrations in samples collected at the first postirradiation mitosis, which may not be indicative of the aberrations formed in interphase after exposure to high-LET radiations. In the present study, we exposed human lymphocytes in vitro to 2 and 5 Gy of gamma rays and 3 Gy of 1 GeV/nucleon iron ions (LET = 140 keV/micrometer), stimulated the cells to grow with phytohemagglutinin (PHA), and collected the condensed chromosomes after 48 h of incubation using both chemically induced premature chromosome condensation (PCC) and the conventional metaphase techniques. The PCC technique used here condenses chromosomes mostly in the G(2) phase of the cell cycle. The F ratio was calculated using data on asymmetrical chromosome aberrations in both the PCC and metaphase samples. It was found that the F ratios were similar for the samples irradiated with low- and high-LET radiation and collected at metaphase. However, for irradiated samples assayed by PCC, the F ratio was found to be 8.2 +/- 2.0 for 5 Gy gamma rays and 5.2 +/- 0.9 for 3 Gy iron ions. The distribution of the aberrations indicated that, in the PCC samples irradiated with iron ions, most of the centric rings occurred in spreads containing five or more asymmetrical aberrations. These heavily damaged cells, which were either less likely to reach mitosis or may reach mitosis at a later time, were responsible for the difference in the F ratios generated from interphase and metaphase analysis after exposure to iron ions.

NASA Discipline Radiation Health↗
NASA NTRS2004

High Order And High Resolution Methods For a Model CAA Problem

The initial value problem for the first order linear wave equation in one space dimension is treated for two cases with specified initial data and grid, and data from solutions at t = 400 and t = 800 are presented, as prescribed for Problem 1 in Category 1. Results are shown from computations with a sequence of recently developed high order and high resolution methods which combine Hermite interpolation, Cauchy-Kowaleskya recursion for time derivatives, and Taylor series time advancement. These methods have the same order of accuracy in time as in space. Results are shown from methods that range from third to nineteenth order. The stated problems with the prescribed coarse grid can be simulated with errors that are at the level of machine accuracy if the method is sufficiently high order. In addition, the growth of the maximum absolute error out to t = 100,000 is given for simulations with the stated problem data.

Goodrich, John W.↗
NASA NTRS1948

An Investigation of the Aerodynamic Characteristics of an 0.08-Scale Model of the Chance Vought XF7U-1 Airplane in the Langley High-Speed 7-by 10-Foot Tunnel: TED No. DE308: Estimated High-Speed Flying Qualities - Part 6

An analysis of the estimated high-speed flying qualities of the Chance Vought XF7U-1 airplane in the Mach number range from 0.40 to 0.91 has been made, based on tests of an 0.08-scale model of this airplane in the Langley high-speed 7- by 10-foot wind tunnel. The analysis indicates longitudinal control-position instability at transonic speeds, but the accompanying trim changes are not large. Control-position maneuvering stability, however, is present for all speeds. Longitudinal lateral control appear adequate, but the damping of the short-period longitudinal and lateral oscillations at high altitudes is poor and may require artificial damping.

Donlan, Charles J.↗
NASA NTRS2005

GRCop-84: A High-Temperature Copper Alloy for High-Heat-Flux Applications

GRCop-84 (Cu-8 at.% Cr-4 at.% Nb) is a new high-temperature copper-based alloy. It possesses excellent high-temperature strength, creep resistance and low-cycle fatigue up to 700 C (1292 F) along with low thermal expansion and good conductivity. GRCop-84 can be processed and joined by a variety of methods such as extrusion, rolling, bending, stamping, brazing, friction stir welding, and electron beam welding. Considerable mechanical property data has been generated for as-produced material and following simulated braze cycles. The data shows that the alloy is extremely stable during thermal exposures. This paper reviews the major GRCop-84 mechanical and thermophysical properties and compares them to literature values for a variety of other high-temperature copper-based alloys.

Ellis, David L.↗
NASA NTRS2004

Microsample Characterization of Coatings for GRCop-84 for High Temperature High Heat Flux Application

NASA's Glenn Research Center has developed GRCop-84 (Cu-8at.%Cr-4% Nb), a high conductivity, high strength copper alloy for use as liners in rocket engine combustion chambers, nozzle ramps and other actively-cooled components subject to high heat fluxes. Two metallic coatings, NiCrAlY and Cu-26%Cr, are being considered for preventing blanching, reducing 'dog- house' failures and providing better environmental resistance to the GRCop-84 liners. This presentation will outline a study of coating-substrate interactions that occur as a result of thermal cycling and coating specific properties at different temperatures. A furnace has been built to thermally cycle the samples under argon. The microsample testing approach is being used to measure the coating-substrate interfacial strength. Cu-26Cr/GRCop-84 samples did not show any obvious interdiffusion after 300 thermal cycles. Interfacial strength tests of these samples were affected by porosity present in the samples. A complete set of observations and results for Cu-26Cr and NiCrAlY coatings will be presented.

Jain, Piyush↗
NASA NTRS2003

High-Speed, High-Temperature Finger Seal Test Evaluated

A finger seal, designed and fabricated by Honeywell Engines, Systems and Services, was tested at the NASA Glenn Research Center at surface speeds up to 1200 ft/s, air temperatures up to 1200 F, and pressures across the seal of 75 psid. These are the first test results obtained with NASA s new High-Temperature, High-Speed Turbine Seal Test Rig (see the photograph). The finger seal is an innovative design recently patented by AlliedSignal Engines, which has demonstrated considerably lower leakage than commonly used labyrinth seals and is considerably cheaper than brush seals. The cost to produce finger seals is estimated to be about half of the cost to produce brush seals. Replacing labyrinth seals with fingers seals at locations that have high-pressure drops in gas turbine engines, typically main engine and thrust seals, can reduce air leakage at each location by 50 percent or more. This directly results in a 0.7- to 1.4-percent reduction in specific fuel consumption and a 0.35- to 0.7-percent reduction in direct operating costs . Because the finger seal is a contacting seal, this testing was conducted to address concerns about its heat generation and life capability at the higher speeds and temperatures required for advanced engines. The test results showed that the seal leakage and wear performance are acceptable for advanced engines.

Proctor, Margaret P.↗
NASA NTRS2007

Active Control of Flow Separation on a High-Lift System with Slotted Flap at High Reynolds Number

The NASA Energy Efficient Transport (EET) airfoil was tested at NASA Langley's Low- Turbulence Pressure Tunnel (LTPT) to assess the effectiveness of distributed Active Flow Control (AFC) concepts on a high-lift system at flight scale Reynolds numbers for a medium-sized transport. The test results indicate presence of strong Reynolds number effects on the high-lift system with the AFC operational, implying the importance of flight-scale testing for implementation of such systems during design of future flight vehicles with AFC. This paper describes the wind tunnel test results obtained at the LTPT for the EET high-lift system for various AFC concepts examined on this airfoil.

Khodadoust, Abdollah↗
NASA NTRS1997

High growth rate homoepitaxial diamond film deposition at high temperatures by microwave plasma-assisted chemical vapor deposition

The deposition of high quality diamond films at high linear growth rates and substrate temperatures for microwave-plasma chemical vapor deposition is disclosed. The linear growth rate achieved for this process is generally greater than 50 .mu.m/hr for high quality films, as compared to rates of less than 5 .mu.m/hr generally reported for MPCVD processes.

Vohra, Yogesh K.↗
NASA NTRS2008

Precipitation-Strengthened, High-Temperature, High-Force Shape Memory Alloys

Shape memory alloys (SMAs) are an enabling component in the development of compact, lightweight, durable, high-force actuation systems particularly for use where hydraulics or electrical motors are not practical. However, commercial shape memory alloys based on NiTi are only suitable for applications near room temperature, due to their relatively low transformation temperatures, while many potential applications require higher temperature capability. Consequently, a family of (Ni,Pt)(sub 1-x)Ti(sub x) shape memory alloys with Ti concentrations ranging from about 15 to 25 at.% have been developed for applications in which there are requirements for SMA actuators to exert high forces at operating temperatures higher than those of conventional binary NiTi SMAs. These alloys can be heat treated in the range of 500 C to produce a series of fine precipitate phases that increase the strength of alloy while maintaining a high transformation temperature, even in Ti-lean compositions.

Noebe, Ronald D.↗
NASA NTRS1947

Investigation of High-Performance Fuels in Multicylinder and in Single-Cylinder Engines at High and Cruising Engine Speeds

An investigation was conducted to compare the knock-limited performance of a 20-percent triptane blend in 28-K fuel with that of 28-R and 33-R fuels at high engine speeds, cruising speeds, and two compression ratios in an K-1830-94 multicylinder engine, Data were obtained with the standard compression ratio of 6.7 and with a compression ratio of 3.0, The three fuels were investigated at engine speeds of 1800, 2250, 2600, and 2800 rpm at high and low blower ratios. A carburetor-air temperature of approximate1y 100 deg F was maintained for the multicylinder-engine runs, Data were obtained on a single R-1830-94 cylinder engine as a means of checking the multicylinder data at the higher speeds. A satisfactory correlation between average mixture temperature and knock-limited manifold pressure was obtained by plotting knock-limited manifold pressure against average mixture temperature for the whole range of engine speeds at constant carburetor air temperature and cylinder-head temperature. The single-cylinder knock-limited performance based on charge-air flow matched that of the multicylinder engine within 6 percent under all the conditions except for 28-R fuel at 2800 rpm; these curves differed from each other by 11 percent in the rich region. The knock rating of 33-R fuel was found to be a little higher than that of the 20-percent triptane blend and 26-R fuel at high mixture temperatures (above 210 deg F) and lean mixtures. The 33-R fuel exhibited rich knock limits appreciably lower than the 20-percent triptane blend, Increasing the compression ratio from 6.7 to 8.0 lowered the knock-limited manifold pressure for all fuels approximately 15 to 18 inches of mercury absolute in the cruising range and 20 to 28 inches of mercury absolute at higher engine speeds. Brake specific fuel consumption was reduced 7 to 9 percent by the increase in compression ratio from 6.7 to 8,0,

Bell, Arthur H.↗