SEARCH · Engineering Papers

Results for “Grain boundary structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

All sources NASA NTRS DOE OSTI

DOE OSTI2024

High-temperature lean Cu alloys with Cr-to-Nb atomic ratio of 2

Two Cu-Cr-Nb alloys, denoted as alloy 1 (comprising Cu-0.89 at% Cr-0.42 at% Nb) and alloy 2 (comprising Cu-1.84 at% Cr-0.99 at% Nb), were produced through a series of manufacturing processes including vacuum induction melting, melt spinning, consolidation, brazing, and baking, with both alloys aimed at achieving a nominal Cr-to-Nb atomic ratio of 2. Microstructural characterization using transmission electron microscopy and X-ray diffraction identified the cubic C15 Laves-phase Cr 2 Nb as the dominant precipitate in both alloys, cross-validated by thermodynamic calculations and atomistic simulation-based density functional theory (DFT). Besides cubic C15 Cr 2 Nb, hexagonal C14-phase Cr 2 Nb and α-BiF3 cubic structured Cr 3 Nb were also observed in the alloys, including a coherent interface formed between the Cr 3 Nb precipitate and the Cu matrix. The hardness of the alloys increases, and the electrical conductivity decreases with increasing alloying addition content; two practical equations described the trends. Further DFT simulations revealed that the electrical conductivity (conductance) of the Cu/Cr 2 Nb interface is an order of magnitude higher than the intrinsic Cu high-angle grain boundaries.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Collaborative R&D with First Solar on Understanding Performance Limitations in CdTe (Project 1 "CdTe" - Mods 0-10, 13, 14-A1, 17)

This CRADA involves analyses on a variety of CdTe and CdTe-PV related materials, test structures, and solar cells produced at FSLR or NREL. Single-crystal (sx) material will be primarily MBE grown and provided by FSLR. Joint activities are focused on establishing the appropriate quality metrics as a basis for high performing sx devices and to study the dopability of the material. Polycrystalline (px) materials will be provided by NREL, FSLR, or fabricated jointly. Px activities are focused on the characterization of performance limiting mechanisms including bulk defects, grain boundaries, and the hetero-interface. A combination of growth, characterization, and theory will be applied. Analysis will include techniques that are well established in CdTe research at NREL (e.g., LIV/DIV/CV, AS/DLTS, LTPL, TRPL) as well as techniques that have not been widely applied to the PV part of CdTe technology (e.g., PCD, CL, uPL, SE).

14 SOLAR ENERGY↗

DOE OSTI2026

Influence of Powder Characteristics and Processing Methods on Creep Performance of Powder Metallurgy Hot Isostatic Pressed SS316

The U.S. nuclear energy expansion goals are driving the demand for manufacturing routes that can rapidly produce large, complex, near net shape components. Powder metallurgy hot isostatic pressing (PM HIP) is an advanced manufacturing technique that can be economically scaled-up, while alleviating the supply chain challenges that forging and casting face in terms of cost and lead time constraints. This makes PM-HIP a viable technology to aid and accelerate large-scale part manufacturing for nuclear applications. However, large-scale qualification and deployment of this technology require a thorough understanding of the influence of powder feedstock quality, powder handling history, hot isostatic pressing (HIP) parameters, and subsequent heat treatment on microstructural evolution and elevated temperature mechanical performance. The present work focusses on 316 austenitic stainless steel (SS316) which is most commonly used in high temperature environments for nuclear applications Results from this study show that PM HIPed SS316 meets ASME tensile requirements at room temperature and at elevated temperature. However, creep performance of PM-HIPed SS316 remains inferior to its wrought counterpart, demonstrating that tensile performance alone is not a reliable metric for long duration high temperature integrity. Further, this report delineates powder derived microstructural features that govern creep damage, with key evidences pointing to “microstructural inheritance” from gas atomized powder feedstocks. Commercial SS316 powders of varying chemical compositions and recycling histories were studies, and the results showed large differences in elemental segregation, oxide surface layers and secondary phase distributions. Multi-scale characterization revealed segregation of chromium, molybdenum, manganese and silicon at the boundaries and the precipitation of manganese-, silicon-, and molybdenum-oxides. During HIP consolidation, these surface oxides transform into decorated prior particle boundaries (PPBs) and grain boundary inclusions that persist through conventional post-HIP solution annealing treatment. The retained oxides in post-HIP microstructures were found to influence grain growth, precipitation behavior, and ultimately creep cavitation and fracture. Such post-HIP heat treatments are therefore limited by a complex trade-off between grain growth, and oxide coarsening which aggravate creep damage by acting as nucleation sites for cavities. The objective of this work is to establish an integrated processing–structure–property framework for PM-HIP 316 stainless steel by investigating the influence of powder feedstock characteristics in pre- and post-HIP processing as well as to understand the significance of post-HIP heat treatment on microstructural evolution and creep properties. The results from this report emphasize the significance of powder feedstock integrity in improving creep performance of PM-HIPed SS316, by highlight the effect of rapid solidification, elemental segregation, oxide formation and powder recycling on microstructural defect inheritance following HIP consolidation. Rather than considering HIP processing, solution annealing, and mechanical performance independently, this report treats powder production, HIP consolidation, post-HIP thermal processing, and creep deformation as interconnected stages within a continuous metallurgical process. The resulting framework will provide a scientific basis for developing feedstock engineering strategies capable of improving long-term reliability of PM-HIP stainless steels and accelerating their qualification for advanced nuclear applications.

Ajjarapu, Pavan [Oak Ridge National Laboratory (OR↗

NASA NTRS1992

Redistribution of Ti and Al in deuterium charged TiAl

The redistribution of titanium and aluminum in a single-phase TiAl alloy that has been exposed to a high pressure of deuterium gas at high temperature is studied. The microstructure in the as-received, uncharged condition consisted of single-phase gamma TiAl grains and a random distribution of precipitates. Precipitates were distributed throughout the matrix and along the grain boundaries. The chemistry of the precipitates varied considerably; some were rich in Al, while other were mostly Ti with some Si and Al. The dislocation density in most grains was low, although in a few grains a high dislocation density was observed. FCC deuterides with a lattice parameter of 0.45 nm form in a Ti-52.1Al-2.1Ta (at. pct) alloy after exposure to 1.38 MPa of deuterium gas at 650 C for 213 hr. The structure and lattice parameter are consistent with the formation of Ti(l)D2. The deuterides that form in this alloy are enriched in Ti and deficient in Al and Ta compared to the deuteride-free matrix. Regions of the matrix contiguous with the deuterides have a correspondingly enhanced aluminum and tantalum concentration.

Legzdina, D.↗

DOE OSTI2022

Synergies between H, He and radiation damage in dual and triple ion irradiation of candidate fusion blanket materials

Three ferritic/martensitic alloys were studied to understand the synergistic effect between single ion beam (Fe 2+ ), dual ion beam (Fe 2+ +He 2+ and Fe 2+ +H + ), and triple ion beam (Fe 2+ +He 2+ +H + ) irradiations on cavity evolution. A commercial alloy, F82H, a castable nanostructured alloy, CNA3, and a high purity model alloy, Fe8Cr2W, were irradiated at 400°C to 600°C to a damage level of 50 dpa at a damage rate of 1 × 10 –3 dpa/s with He and H injection rates of 10 and 40 appm/dpa, respectively. Post-irradiation characterization via bright field transmission electron microscopy and high-angle annular dark-field scanning transmission electron microscopy was performed on all irradiated conditions to characterize the cavity size distribution and determine the effects of H/He injection on cavity microstructure. In all three alloys, hydrogen co-injection with helium resulted in an increased cavity number density and maximum cavity size, producing an increase in swelling over that from helium injection alone. Swelling in F82H appears to peak between 450°C and 500°C. At 600°C, swelling was minimal and cavities of high density and small size were confined to grain boundaries and dislocations while at 400°C, swelling is also low with a nearly homogeneous, high density, distribution of very small cavities throughout. Swelling was least in the commercial alloy F82H due to the high sink strength. The CNA3 alloy underwent dissolution of precipitates that lowered the sink strength and resulted in higher swelling than F82H, but less than the model alloy. Electron energy loss spectroscopy (EELS) elemental mapping revealed hydrogen forming a halo-like structure about the periphery of the cavities and helium residing within the cavities themselves. Finally, this observation suggests that hydrogen reduces the surface energy of helium-filled cavities which results in both increased cavity number density and cavity size in triple beam irradiation over dual beam irradiation.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Grain refinement in titanium prevents low temperature oxygen embrittlement

Interstitial oxygen embrittles titanium, particularly at cryogenic temperatures, which necessitates a stringent control of oxygen content in fabricating titanium and its alloys. Here, we propose a structural strategy, via grain refinement, to alleviate this problem. Compared to a coarse-grained counterpart that is extremely brittle at 77 K, the uniform elongation of an ultrafine-grained (UFG) microstructure (grain size ~ 2.0 µm) in Ti-0.3wt.%O is successfully increased by an order of magnitude, maintaining an ultrahigh yield strength inherent to the UFG microstructure. This unique strength-ductility synergy in UFG Ti-0.3wt.%O is achieved via the combined effects of diluted grain boundary segregation of oxygen that helps to improve the grain boundary cohesive energy and enhanced dislocation activities that contribute to the excellent strain hardening ability. The present strategy will not only boost the potential applications of high strength Ti-O alloys at low temperatures, but can also be applied to other alloy systems, where interstitial solution hardening results into an undesirable loss of ductility.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Grain boundary zirconia-modified garnet solid-state electrolyte

Here, we report a method for promoting electrochemical stability in garnet Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 solid-state electrolyte based on a composite two-phase oxide–oxide microstructure. Grain boundary precipitation of the controlled distribution of amorphous zirconium oxide microparticles is achieved through the addition of reactive tantalum carbide. During ambient-atmosphere sintering, the carbide decomposes through an in situ reaction, the ‘extra’ Ta substituting for Zr within the Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 lattice. Density functional theory (DFT) calculations identify a thermodynamically favourable reaction path and show how substituting Ta 5+ at Zr 4+ sites affects the crystal structure as well as bulk ionic and electronic conductivities. Quantitative stereology highlights that zirconia also acts as a sintering aid, reducing compact porosity. Cryogenic focused-ion-beam scanning electron microscopy and fractography analysis of cycled solid-state electrolytes illustrates that near-universally observed intergranular Li-metal dendrite propagation is suppressed by the two-phase microstructure, favouring transgranular dendrites instead. Importantly, DFT demonstrates that compared with the Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 surface, the zirconium oxide surface per se is less electronically conductive and does not trap excess electrons to reduce Li ions. This is a key reason for the substantial improvement in the electrochemical properties over the single-phase baseline.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Ferroelectric HfO 2 and the importance of strain

Ferroelectric oxides based on HfO 2 show tremendous promise for the next generation of memory and logic devices. The ferroelectric polymorph is one of several that can be derived from the high symmetry cubic fluorite structure of HfO 2 . A single grain of HfO 2 may consist of a coherent mixture of multiple orientational and translational variants of different polymorphs. Here, we use symmetry-adapted strain-order parameters to elucidate the relationship between the different HfO 2 polymorphs and their symmetrically equivalent variants. We use first-principles electronic structure methods to identify minimum energy pathways and map them in subspaces of the symmetry-adapted strain order parameters. We next investigate the atomic structure of domain boundaries that separate coexisting variants of ferroelectric HfO 2 . Further, we rely on Gibbsian excess quantities and a precise specification of mechanical boundary conditions to describe the thermodynamic properties of domain boundaries. Our first-principles calculations show that the O and Hf shuffle arrangement within a domain boundary is closely related to the intermediate shuffle patterns of the homogeneous pathways between ferroelectric variants. Furthermore, the preferred structure within a boundary is very sensitive to local strain constraints imposed by the adjacent ferroelectric variants, leading to highly anisotropic domain boundary energies.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Defect-Enabled Phase Programming of Transition Metal Dichalcogenide Monolayers

The ability to tune the local electronic transport properties of group VI transition metal dichalcogenide (TMD) monolayers by strain-induced structural phase transformations (“phase programming”) has stimulated much interest in the potential applications of such layers as ultrathin programmable and dynamically switchable nanoelectronics components. In this manuscript, we propose a new approach toward controlling TMD monolayer phases by employing macroscopic in-plane strains to amplify heterogeneous strains arising from tailored, spatially extended defects within the monolayer. Furthermore, the efficacy of our proposed approach is demonstrated via numerical simulations of emerging domains localized around arrays of holes, grain boundaries, and compositional heterointerfaces. Quantitative relations between the macroscopic strains required, spatial resolution of domain patterns, and defect configurations are developed. In particular, the introduction of arrays of holes is identified as the most feasible phase programming route.

2D materials↗

DOE OSTI2021

Evaluation of BISON's Transient Fission Gas Release Model on High-Burnup UO 2 MiniFuel

BISON's fission gas release (FGR) model has been evaluated and tested over several hypothetical thermal transient cases at high burnup and validated against FGR experimental data from an annealing test at high burnup. Diffusion-controlled FGR is accounted for in the model by including several physical mechanisms such as the diffusion of fission gas to grain faces, grain boundary sweeping, grain growth, and intergranular bubble growth. Under temperature variations, FGR is increased due to the development of micro-cracks at grain faces. This existing transient capability, however, was developed based on transient fuel behavior during power ramps and the associated micro-cracking process. Nevertheless, a fraction of the FGR during temperature transients such as LOCA can ensue from different mechanisms (in particular, fuel fragmentation) and present an important dependency on local burnup and high burnup structure formation. It follows that the performance and necessary developments of the existing BISON fission gas model for the analysis of LOCA-type transients need to be investigated through a systematic assessment study. Such a study is performed in this work. The model shows an overall good qualitative agreement with experimental observations on FGR during annealing tests with different temperature conditions. It also accounts well for microstructural effects on FGR. When quantitatively compared to FGR data from previously irradiated 103 MWd/kgU UO 2 discs under thermal annealing, the model shows a less satisfactory agreement with the experimental data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1984

Characterization of erosion of metallic materials under cavitation attack in a mineral oil

Cavitation erosion and erosion rates of eight metallic materials representing three crystal structures were studied using a 20-kHz ultrasonic magnetostrictive oscillator in viscous mineral oil. The erosion rates of the metals with an fcc matrix were 10 to 100 times higher than that of an hcp-matrix titanium alloy. The erosion rates of iron and molybdenum, with bcc matrices, were higher than that of the titanium alloy but lower than those of the fcc metals. Scanning electron microscopy indicates that the cavitation pits are initially formed at the grain boundaries and precipitates and that the pits that formed at the triple points grew faster than the others. Transcrystalline craters formed by cavitation attack over the surface of grains and roughened the surfaces by multiple slip and twinning. Surface roughness measurements show that the pits that formed over the grain boundaries deepended faster than other pits. Computer analysis revealed that a geometric expression describes the nondimensional erosion curves during the time period 0.5 t(0) t 2.5 t(0), where t(0) is the incubation period. The fcc metals had very short incubation periods; the titanium alloy had the longest incubation period.

Rao, B. C. S.↗

DOE OSTI2020

Irradiation Creep in Materials

A knowledge of the dimensional stability of reactor structural components, under irradiation conditions, is of major importance in the design of thermal, fast, and fusion reactors. When subjected to simultaneous mechanical loading and irradiation, structural materials exhibit a visco-plastic deformation phenomenon, referred to as irradiation creep, which can be more rapid than the deformation occurring out of irradiation. In this article, the phenomenology of this peculiar behavior is described after a short history of its discovery. Then, the theoretical mechanisms proposed in the literature during these past 60 years are presented, with a special focus on mechanisms based on stress induced preferred absorption of point defects by dislocation loops, dislocations and grain boundaries and on mechanisms based on climb-enhanced glide of dislocations. These mechanisms are discussed in the light of experimental evidences. Finally, irradiation creep in various materials, such as zirconium alloys, austenitic stainless steels, nickel-based alloys, ferritic-martensitic steels and graphite, is described.

Onimus, Fabien↗

DOE OSTI2026

BSMV-mediated genome editing exhibits host-specific heritability: germline transmission in barley and somatic edits in Nicotiana benthamiana

Plant RNA virus–mediated guide RNA (gRNA) delivery represents a transformative advance in genome editing technologies. Unlike conventional transformation methods that rely on labor-intensive tissue culture and regeneration for each individual gRNA delivery, viral vectors can rapidly and systemically transmit gRNAs into pre-established Cas-expressing plants, providing an accelerated route for functional genomics and trait discovery directly in planta . However, key design parameters, including subgenomic promoter choice, transcript architecture, and their effects on viral fitness and editing outcomes, remain to be elucidated for most viral platforms. We developed five Barley stripe mosaic virus (BSMV) vectors, each with distinct subgenomic promoter elements to drive single gRNA expression. These were initially evaluated in Cas9-expressing transgenic Nicotiana benthamiana plants targeting the Phytoene desaturase ( PDS ) gene to compare their editing efficiencies. Single gRNAs expressed under the duplicated γb subgenomic promoter or when fused directly to the γb genome achieved the highest mutation frequencies (up to 90% at 60 days post-inoculation), whereas β1- and β2-driven sgRNAs produced delayed and reduced editing. Thus, promoter selection critically determines gRNA accumulation and the efficacy of BSMV-mediated genome editing. The top-performing design was then applied to Cas9-expressing barley ( Hordeum vulgare ) targeting HvCMF7 (conferring green-white variegation) and HvGW2.1 (impacts grain width and weight). BSMV spread systemically throughout barley, inducing somatic and heritable mutations at frequencies up to 100%, with virus-free edited progeny. In contrast, despite robust somatic editing in N. benthamiana, no heritable mutations were detected indicating species-dependent limitations in germline transmission. Our systematic comparison of subgenomic promoter architectures establishes clear design principles for optimizing viral vector–mediated delivery. Promoter choice and transcript structure critically shape editing efficiency and viral stability. The host-specific boundary for germline editing, defined by efficient heritable editing in barley but not N. benthamiana , highlights where BSMV offers advantages and where alternative vectors or hybrid strategies are required, guiding rational platform selection for diverse crop species and applications. Collectively, these findings establish BSMV as a promising next-generation vector for rapid, tissue culture–free, and transformation-independent genome editing in cereals and other recalcitrant monocots.

barley↗

DOE OSTI2022

The complex structural and chemical nature of monolithic U-10Mo fuel and Zr barrier layer

Nanoscale microstructural characterization by advanced transmission electron microscopy techniques on a U-10Mo/Zr barrier layer monolithic fuel plate was performed to evaluate the microstructural evaluation after high burn-up. Gas bubble superlattice evolution, grain restructuring, and evolution of the Zr interaction layer is investigated through detailed electron microscopy characterization. The use of automated crystallographic orientation mapping to irradiated U-10Mo fuel highlights that the restructured ultra-fine grains are separated by high angle grain boundaries at a burn up of 4.42 × 10 21 fissions/cm 3 . Additionally, advanced chemical analysis and multi-variable statistical analysis shows spatial clustering of solid fission product precipitates. Finally, characterization of a newly observed porous nanocrystalline Zr region in the barrier layer is studied. Finally, this work provides insights into the grain subdivision and restructuring process while using advanced microscopy techniques to analyze fission products in neutron-irradiated U-10Mo fuel.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Effects of dose rate on the microstructure and deuterium retention in γ-LiAlO 2 pellets

This report presents experimental findings obtained from November 2024 to September 2025. Defect accumulation and microstructural evolution during ion irradiation at elevated temperatures are governed by two competing processes: defect production, driven by dose rate, and defect recovery, controlled by defect diffusion, interaction, and annihilation. At a given dose, the resulting microstructural evolution depends on both the dose rate and irradiation temperature. As a continuation of our FY24 tritium science project, which investigated temperature effects at a fixed dose rate, this study focuses on dose-rate effects at a fixed temperature to provide deeper insights into the irradiated microstructure and compositional changes in γ-LiAlO 2 pellets. The study aims to elucidate the impact of dose rate on microstructure, precipitate morphology, deuterium retention, and lithium volatility in γ-LiAlO 2 pellets under sequential 120 keV He + and 80 keV D 2 + ion irradiation. Three dose rates of 7.3×10 4 , 2.9×10 4 and 6.8×10 5 dpa/s were applied to achieve the same total ion fluence of 2×10 17 (He + +D + )/cm 2 at 500 °C, corresponding to a maximum combined dose of 7.55 dpa at ~255 nm. The irradiated pellets were subsequently characterized using scanning transmission electron microscopy (STEM) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). The microstructural response of γ-LiAlO 2 to ion irradiation was found to be strongly dose-rate dependent. At medium and high dose rates, irradiation produced a surface amorphized layer and an underlying crystalline layer containing LiAl 5 O 8 precipitates, with implanted gases accumulating and forming blisters at the crystalline-amorphous interface. It remains to be investigated whether the amorphized layer was produced by He + ion irradiation prior to D 2 + ion irradiation. In contrast, at low dose rates, the material remained crystalline, with cavities, likely gas-filled, distributed around precipitates, within the γ-LiAlO 2 matrix, and along grain boundaries. While precipitate morphology exhibited anisotropy, their size showed little sensitivity to dose rate in the applied range of this study. This result, however, does not rule out the possibility that further reductions in dose rate could influence precipitate size. High dose-rate irradiation enhanced protonium–deuterium isotopic exchange and lithium depletion in the amorphized region. Collectively, the results show that dose rate governs amorphization, gas redistribution, isotopic exchange, and lithium depletion, providing important insights into the mechanisms underlying structural evolution in γ-LiAlO 2 pellets under reactor-relevant irradiation conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1981

EBIC/TEM investigations of defects in solar silicon ribbon materials

Transmission electron microscopy was used to investigate the defect structure of edge defined film growth (EFG) material, web dentritic ribbons (WEB), and ribbon to ribbon recrystallized material (RTR). The most common defects in all these materials are coherent first order twin boundaries. These coherent twins can be very thin, a few atomic layers. Bundles of the twins which contain odd numbers of twins will in optical images appear as a seemingly single first twin boundary. First-order coherent twin boundaries are not electrically active, except at locations where they contain intrinsic (grain boundary) dislocations. These dislocations take up small deviations from the ideal twin relation and play the same role in twin boundaries as conventional and play the some role in twin boundaries as conventional edge and screw dislocations in small angle tilt and twist boundaries.

Ast, D. G.↗

DOE OSTI2022

Confinement‐Driven Inverse Domain Scaling in Polycrystalline ErMnO 3

Abstract The research on topological phenomena in ferroelectric materials has revolutionized the way people understand polar order. Intriguing examples are polar skyrmions, vortex/anti‐vortex structures, and ferroelectric incommensurabilties, which promote emergent physical properties ranging from electric‐field‐controllable chirality to negative capacitance effects. Here, the impact of topologically protected vortices on the domain formation in improper ferroelectric ErMnO 3 polycrystals is studied, demonstrating inverted domain scaling behavior compared to classical ferroelectrics. It is observed that as the grain size increases, smaller domains are formed. Phase field simulations reveal that elastic strain fields drive the annihilation of vortex/anti‐vortex pairs within the grains and individual vortices at the grain boundaries. The inversion of the domain scaling behavior has far‐reaching implications, providing fundamentally new opportunities for topology‐based domain engineering and the tuning of the electromechanical and dielectric performance of ferroelectrics in general.

36 MATERIALS SCIENCE↗

NASA NTRS1992

Recent results on Mars and Venus; Proceedings of Symposium 3 and the Topical Meetings of the Interdisciplinary Scientific Commission C (Meeting C1) and D (Meeting D1) of the COSPAR 28th Plenary Meeting, The Hague, Netherlands, June 25-July 6, 1990

In this volume, latest results on Mars and Phobos studies are discussed along with recent results on Venus and on Martian plasma environment. Papers are presented on the characteristics of aerosol phenomena in Martian atmosphere from KRFM-experiment data, Phobos map and Phobos globe, submicron-sized dust grains in the Martian environment, remote sensing of Venus atmospheric dynamics, the latitude structure of upper clouds of Venus, and Venus thermospheric response to short-term solar variations. Attention is also given to a comparison between the bow shocks and magnetotails of Venus and Mars, comparative studies of the solar wind interaction with weakly magnetized planets, the magnetic field environment of Mars as studied by Phobos-2, waves and cold plasmas near Mars, and multiple-ion effects at Martian plasma boundaries.

Shorthill, R. W.↗