Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Filter error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Reference-cell calibration activities

The use of secondary calibration in large area pulsed solar simulators (LAPSS) is discussed. It is argued that primary calibration in sunlight is time consuming, that only a limited sun calibration of a set of primary reference cells is required, that the LAPSS light source is filtered to closely match the am 1.5 direct spectrum, and that the temperal stability of the filtered LAPSS is excellent. There is the possibility of a lower error rate. Lower costs are anticipated.

Mueller, R.↗
NASA NTRS1987

High dynamic GPS receiver using maximum likelihood estimation and frequency tracking

A new high dynamic global positioning system (GPS) receiver is presented and its performance characterized by analysis, simulation, and demonstration. The demonstration receiver is a breadboard model capable of tracking a single simulated satellite signal in pseudorange and range rate. Pseudorange and range rate estimates are made once every 20 ms, using a maximum likelihood estimator, and are tracked by means of a third-order fading memory filter in a feedback configuration. The receiver tracks pseudorange with rms errors of under 1 m when subjected to simulated 50 g, 40 g/s circular trajectories. The tracking threshold is approximately 28 dB-Hz, which provides 12 dB margin relative to the minimum specified signal strength, assuming 3.5 dB system noise figure and 0 dBi antenna gain.

Hurd, W. J.↗
NASA NTRS1990

Digital accumulators in phase and frequency tracking loops

Results on the effects of digital accumulators in phase and frequency tracking loops are presented. Digital accumulators or summers are used extensively in digital signal processing to perform averaging or to reduce processing rates to acceptable levels. For tracking the Doppler of high-dynamic targets at low carrier-to-noise ratios, it is shown through simulation and experiment that digital accumulators can contribute an additional loss in operating threshold. This loss was not considered in any previous study and needs to be accounted for in performance prediction analysis. Simulation and measurement results are used to characterize the loss due to the digital summers for three different tracking loops: a digital phase-locked loop, a cross-product automatic frequency tracking loop, and an extended Kalman filter. The tracking algorithms are compared with respect to their frequency error performance and their ability to maintain lock during severe maneuvers at various carrier-to-noise ratios. It is shown that failure to account for the effect of accumulators can result in an inaccurate performance prediction, the extent of which depends highly on the algorithm used.

Hinedi, Sami↗
NASA NTRS1997

The use of magnetic field data to estimate attitude and trajectory for the Rossi X-Ray Timing Explorer (RXTE)

A single augmented extended Kalman filter (EKF) is proposed for the simultaneous and autonomous estimation of spacecraft trajectory and attitude with data from the Rossi X-ray timing explorer (RXTE) magnetometer and gyro-measured body rates. The derivation of the EKF is outlined, including the measurement update and the propagation. The results from a 12 hour span of data are processed and compared with operational estimations computed at the NASA Goddard Space Flight Center (MD). The filter was found to be able to overcome very large initial errors and converge to steady state averages of less than 30 km in position, 0.05 km/s in velocity and 3 deg in attitude.

Deutschmann, Julie↗
NASA NTRS2004

Accuracy Assessments and Validation of an Expanded UV Irradiance Database from Satellite Total Ozone Mapping Spectrometer (TOMS)

The TOMS UV irradiance database (1978 to 2000) has been expanded to include 5 new products (noon irradiance at 305, 310, 324, and 380 nm, and noon erythemal-weighted irradiance), in addition to the existing erythemal daily exposure, which permit direct Comparisons with ground-based measurements from UV spectrometers. Sensitivity studies are conducted to estimate uncertainties of the new TOMS UV irradiance data due to algorithm apriori assumptions. Comparisons with Brewer spectrometers as well as filter radiometers are used to review of the sources of known errors. Inability to distinguish between snow and cloud cover using only TOMS data results in large errors in estimating surface UV using snow climatology. A correction is suggested for the case when the regional snow albedo is known from an independent source. The summer-time positive bias between TOMS UV estimations and Brewer measurements can be seen at all wavelengths. This suggests the difference is not related to ozone absorption effects. We emphasize that uncertainty of boundary layer UV aerosol absorption properties remains a major source of error in modeling UV irradiance in clear sky conditions. Neglecting aerosol absorption by the present TOMS algorithm results in a positive summertime bias in clear-sky UV estimations over many locations. Due to high aerosol variability the bias is strongly site dependent. Data from UV-shadow-band radiometer and well-calibrated CIMEL sun-sky radiometer are used to quantify the bias at NASA/GSFC site in Greenbelt, MD. Recommendations are given to enable potential users to better account for local conditions by combining standard TOMS UV data with ancillary ground measurements.

Krotkov, N. A.↗
NASA NTRS2007

Hierarchically Structured Non-Intrusive Sign Language Recognition

This work presents a hierarchically structured approach at the nonintrusive recognition of sign language from a monocular frontal view. Robustness is achieved through sophisticated localization and tracking methods, including a combined EM/CAMSHIFT overlap resolution procedure and the parallel pursuit of multiple hypotheses about hands position and movement. This allows handling of ambiguities and automatically corrects tracking errors. A biomechanical skeleton model and dynamic motion prediction using Kalman filters represents high level knowledge. Classification is performed by Hidden Markov Models. 152 signs from German sign language were recognized with an accuracy of 97.6%.

Zieren, Jorg↗
NASA NTRS2001

Stable and verifiable state estimation methods and systems with spacecraft applications

The stability of a recursive estimator process (e.g., a Kalman filter is assured for long time periods by periodically resetting an error covariance P(t.sub.n) of the system to a predetermined reset value P.sub.r. The recursive process is thus repetitively forced to start from a selected covariance and continue for a time period that is short compared to the system's total operational time period. The time period in which the process must maintain its numerical stability is significantly reduced as is the demand on the system's numerical stability. The process stability for an extended operational time period T.sub.o is verified by performing the resetting step at the end of at least one reset time period T.sub.r whose duration is less than the operational time period T.sub.o and then confirming stability of the process over the reset time period T.sub.r. Because the recursive process starts from a selected covariance at the beginning of each reset time period T.sub.r, confirming stability of the process over at least one reset time period substantially confirms stability over the longer operational time period T.sub.o.

Li, Rongsheng↗
NASA NTRS2012

An Iterated Global Mascon Solution with Focus on Land Ice Mass Evolution

Land ice mass evolution is determined from a new GRACE global mascon solution. The solution is estimated directly from the reduction of the inter-satellite K-band range rate observations taking into account the full noise covariance, and formally iterating the solution. The new solution increases signal recovery while reducing the GRACE KBRR observation residuals. The mascons are estimated with 10-day and 1-arc-degree equal area sampling, applying anisotropic constraints for enhanced temporal and spatial resolution of the recovered land ice signal. The details of the solution are presented including error and resolution analysis. An Ensemble Empirical Mode Decomposition (EEMD) adaptive filter is applied to the mascon solution time series to compute timing of balance seasons and annual mass balances. The details and causes of the spatial and temporal variability of the land ice regions studied are discussed.

Luthcke, S. B.↗
NASA NTRS2014

Estimation of Crop Gross Primary Production (GPP): I. Impact of MODIS Observation Footprint and Impact of Vegetation BRDF Characteristics

Accurate estimation of gross primary production (GPP) is essential for carbon cycle and climate change studies. Three AmeriFlux crop sites of maize and soybean were selected for this study. Two of the sites were irrigated and the other one was rainfed. The normalized difference vegetation index (NDVI), the enhanced vegetation index (EVI), the green band chlorophyll index (CIgreen), and the green band wide dynamic range vegetation index (WDRVIgreen) were computed from the moderate resolution imaging spectroradiometer (MODIS) surface reflectance data. We examined the impacts of the MODIS observation footprint and the vegetation bidirectional reflectance distribution function (BRDF) on crop daily GPP estimation with the four spectral vegetation indices (VIs - NDVI, EVI, WDRVIgreen and CIgreen) where GPP was predicted with two linear models, with and without offset: GPP = a × VI × PAR and GPP = a × VI × PAR + b. Model performance was evaluated with coefficient of determination (R2), root mean square error (RMSE), and coefficient of variation (CV). The MODIS data were filtered into four categories and four experiments were conducted to assess the impacts. The first experiment included all observations. The second experiment only included observations with view zenith angle (VZA) ≤ 35◦ to constrain growth of the footprint size,which achieved a better grid cell match with the agricultural fields. The third experiment included only forward scatter observations with VZA ≤ 35◦. The fourth experiment included only backscatter observations with VZA ≤ 35◦. Overall, the EVI yielded the most consistently strong relationships to daily GPP under all examined conditions. The model GPP = a × VI × PAR + b had better performance than the model GPP = a × VI × PAR, and the offset was significant for most cases. Better performance was obtained for the irrigated field than its counterpart rainfed field. Comparison of experiment 2 vs. experiment 1 was used to examine the observation footprint impact whereas comparison of experiment 4 vs. experiment 3 was used to examine the BRDF impact. Changes in R2, RMSE,CV and changes in model coefficients "a" and "b" (experiment 2 vs. experiment 1; and experiment 4 vs. experiment 3) were indicators of the impacts. The second experiment produced better performance than the first experiment, increasing R2 (↑0.13) and reducing RMSE (↓0.68 g C m−2 d−1) and CV (↓9%). For each VI, the slope of GPP = a × VI × PAR in the second experiment for each crop type changed little while the slope and intercept of GPP = a × VI × PAR + b varied field by field. The CIgreen was least affected by the MODIS observation footprint in estimating crop daily GPP (R2, ↑0.08; RMSE, ↓0.42 g C m−2 d−1; and CV, ↓7%). Footprint most affected the NDVI (R2, ↑0.15; CV, ↓10%) and the EVI (RMSE, ↓0.84 g C m−2 d−1). The vegetation BRDF impact also caused variation of model performance and change of model coefficients. Significantly different slopes were obtained for forward vs. backscatter observations, especially for the CIgreen and the NDVI. Both the footprint impact and the BRDF impact varied with crop types, irrigation options, model options and VI options.

Chlorophyll↗
NASA NTRS2013

Aerosol Optical Depths over Oceans: a View from MISR Retrievals and Collocated MAN and AERONET in Situ Observations

In this study, aerosol optical depths over oceans are analyzed from satellite and surface perspectives. Multiangle Imaging SpectroRadiometer (MISR) aerosol retrievals are investigated and validated primarily against Maritime Aerosol Network (MAN) observations. Furthermore, AErosol RObotic NETwork (AERONET) data from 19 island and coastal sites is incorporated in this study. The 270 MISRMAN comparison points scattered across all oceans were identified. MISR on average overestimates aerosol optical depths (AODs) by 0.04 as compared to MAN; the correlation coefficient and root-mean-square error are 0.95 and 0.06, respectively. A new screening procedure based on retrieval region characterization is proposed, which is capable of substantially reducing MISR retrieval biases. Over 1000 additional MISRAERONET comparison points are added to the analysis to confirm the validity of the method. The bias reduction is effective within all AOD ranges. Setting a clear flag fraction threshold to 0.6 reduces the bias to below 0.02, which is close to a typical ground-based measurement uncertainty. Twelve years of MISR data are analyzed with the new screening procedure. The average over ocean AOD is reduced by 0.03, from 0.15 to 0.12. The largest AOD decrease is observed in high latitudes of both hemispheres, regions with climatologically high cloud cover. It is postulated that the screening procedure eliminates spurious retrieval errors associated with cloud contamination and cloud adjacency effects. The proposed filtering method can be used for validating aerosol and chemical transport models.

AERONET↗
NASA NTRS1975

A prefiltering version of the Kalman filter with new numerical integration formulas for Riccati equations

A prefiltering version of the Kalman filter is derived for both discrete and continuous measurements. The derivation consists of determining a single discrete measurement that is equivalent to either a time segment of continuous measurements or a set of discrete measurements. This prefiltering version of the Kalman filter easily handles numerical problems associated with rapid transients and ill-conditioned Riccati matrices. Therefore, the derived technique for extrapolating the Riccati matrix from one time to the next constitutes a new set of integration formulas which alleviate ill-conditioning problems associated with continuous Riccati equations. Furthermore, since a time segment of continuous measurements is converted into a single discrete measurement, Potter's square root formulas can be used to update the state estimate and its error covariance matrix. Therefore, if having the state estimate and its error covariance matrix at discrete times is acceptable, the prefilter extends square root filtering with all its advantages, to continuous measurement problems.

Womble, M. E.↗
NASA NTRS2017

Filter Tuning Using the Chi-Squared Statistic

This paper examines the use of the Chi-square statistic as a means of evaluating filter performance. The goal of the process is to characterize the filter performance in the metric of covariance realism. The Chi-squared statistic is the value calculated to determine the realism of a covariance based on the prediction accuracy and the covariance values at a given point in time. Once calculated, it is the distribution of this statistic that provides insight on the accuracy of the covariance. The process of tuning an Extended Kalman Filter (EKF) for Aqua and Aura support is described, including examination of the measurement errors of available observation types, and methods of dealing with potentially volatile atmospheric drag modeling. Predictive accuracy and the distribution of the Chi-squared statistic, calculated from EKF solutions, are assessed.

Filter Tuning↗
NASA NTRS1975

A minimax technique for time-domain design of preset digital equalizers using linear programming

A linear programming technique is presented for the design of a preset finite-impulse response (FIR) digital filter to equalize the intersymbol interference (ISI) present in a baseband channel with known impulse response. A minimax technique is used which minimizes the maximum absolute error between the actual received waveform and a specified raised-cosine waveform. Transversal and frequency-sampling FIR digital filters are compared as to the accuracy of the approximation, the resultant ISI and the transmitted energy required. The transversal designs typically have slightly better waveform accuracy for a given distortion; however, the frequency-sampling equalizer uses fewer multipliers and requires less transmitted energy. A restricted transversal design is shown to use the least number of multipliers at the cost of a significant increase in energy and loss of waveform accuracy at the receiver.

Vaughn, G. L.↗
NASA NTRSDate not supplied

Onboard Navigation Error Analysis for Aerocapture at Uranus

Capturing into an orbit around Uranus using aerocapture allows one to design a mission with faster interplanetary trajectories and less propellant requirements. Such an aerocapture mission would rely on the onboard Guidance, Navigation, and Control (GNC) subsystems to successfully capture into an orbit around Uranus. Uncertainty in the state information and the noise in the sensor measurements induce navigation errors in the guidance and control subsystems, which can affect the overall performance of the aerocapture mission at Uranus. Understanding the effect of these navigation errors on mission performance is essential. To this end, this work considers different sensors with varying quality to understand their impact on the overall mission performance. In addition, this paper studies the impact of the uncertainty in the initial states used to initialize the onboard navigation filter and understands their effect on mission performance. This paper also shows the onboard navigation errors obtained from the Linear Covariance (LinCov) analysis and uses them for verification and validation (V&V) of the results from Program to Optimize and Simulate Trajectories-II (POST2).

Pardha Sai Chadalavada↗
NASA NTRSDate not supplied

Onboard Navigation Error Analysis for Aerocapture at Uranus

Capturing into an orbit around Uranus using aerocapture allows one to design a mission with faster interplanetary trajectories and less propellant requirements. Such an aerocapture mission would rely on the onboard Guidance, Navigation, and Control (GNC) subsystems to successfully capture into an orbit around Uranus. Uncertainty in the state information and the noise in the sensor measurements induce navigation errors in the guidance and control subsystems, which can affect the overall performance of the aerocapture mission at Uranus. Understanding the effect of these navigation errors on mission performance is essential. To this end, this work considers different sensors with varying quality to understand their impact on the overall mission performance. In addition, this paper studies the impact of the uncertainty in the initial states used to initialize the onboard navigation filter and understands their effect on mission performance. This paper also shows the onboard navigation errors obtained from the Linear Covariance (LinCov) analysis and uses them for verification and validation (V\&V) of the results from Program to Optimize and Simulate Trajectories-II (POST2).

Aerocapture↗
DOE OSTI2023

Merger identification through photometric bands, colours, and their errors

Aims. We present the application of a fully connected neural network (NN) for galaxy merger identification using exclusively photometric information. Our purpose is not only to test the method’s efficiency, but also to understand what merger properties the NN can learn and what their physical interpretation is. Methods. We created a class-balanced training dataset of 5860 galaxies split into mergers and non-mergers. The galaxy observations came from SDSS DR6 and were visually identified in Galaxy Zoo. The 2930 mergers were selected from known SDSS mergers and the respective non-mergers were the closest match in both redshift and r magnitude. The NN architecture was built by testing a different number of layers with different sizes and variations of the dropout rate. We compared input spaces constructed using: the five SDSS filters: u, g, r, i, and z; combinations of bands, colours, and their errors; six magnitude types; and variations of input normalization. Results. We find that the fibre magnitude errors contribute the most to the training accuracy. Studying the parameters from which they are calculated, we show that the input space built from the sky error background in the five SDSS bands alone leads to 92.64 ± 0.15% training accuracy. We also find that the input normalization, that is to say, how the data are presented to the NN, has a significant effect on the training performance. Conclusions. We conclude that, from all the SDSS photometric information, the sky error background is the most sensitive to merging processes. This finding is supported by an analysis of its five-band feature space by means of data visualization. Moreover, studying the plane of the g and r sky error bands shows that a decision boundary line is enough to achieve an accuracy of 91.59%.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1988

Wiener restoration of sampled image data - End-to-end analysis

The Wiener filter is formulated as a function of the basic image-gathering and image-reconstruction constraints, thereby providing a method for minimizing the mean-squared error between the (continuous-input) radiance field and its restored (continuous-output) representation. This formulation of the Wiener filter is further extended to the Wiener-characteristic filter, which provides a method for explicitly specifying the desired representation. Two specific examples of Wiener filters are presented.

Fales, Carl L.↗
NASA NTRS2003

Divergence Free High Order Filter Methods for Multiscale Non-ideal MHD Flows

Low-dissipative high order filter finite difference methods for long time wave propagation of shock/turbulence/combustion compressible viscous MHD flows has been constructed. Several variants of the filter approach that cater to different flow types are proposed. These filters provide a natural and efficient way for the minimization of the divergence of the magnetic field (Delta . B) numerical error in the sense that no standard divergence cleaning is required. For certain 2-D MHD test problems, divergence free preservation of the magnetic fields of these filter schemes has been achieved.

Yee, H. C.↗