Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FEET”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Sound Pressures and Correlations of Noise on the Fuselage of a Jet Aircraft in Flight

Tests were conducted at altitudes of 10,000, 20,000, and 30,000 feet at speeds of Mach 0.4, 0.6, and O.8. It was found that the sound pressure levels on the aft fuselage of a jet aircraft in flight can be estimated using an equation involving the true airspeed and the free air density. The cross-correlation coefficient over a spacing of 2.5 feet was generalized with Strouhal number. The spectrum of the noise in flight is comparatively flat up to 10,000 cycles per second.

Shattuck, Russell D.↗

Free-Spinning-Tunnel Investigation of a 1/25-Scale Model of the Chance Vought F8U-1P Airplane

An investigation has been made in the Langley 20-foot free-spinning tunnel on a 1/25-scale dynamic model to determine the spin and recovery characteristics of the Chance Vought F8U-1P airplane. Results indicated that the F8U-IP airplane would have spin-recovery characteristics similar to the XF8U-1 design, a model of which was tested and the results of the tests reported in NACA Research Memorandum SL56L31b. The results indicate that some modification in the design, or some special technique for recovery, is required in order to insure satisfactory recovery from fully developed erect spins. The recommended recovery technique for the F8U-lP will be full rudder reversal and movement of ailerons full with the spin (stick right in a right spin) with full deflection of the wing leading- edge flap. Inverted spins will be difficult to obtain and any inverted spin obtained should be readily terminated by full rudder reversal to oppose the yawing rotation and neutralization of the longitudinal and lateral controls. In an emergency, the same size parachute recommended for the XFBU-1 airplane will be adequate for termination of the spin: a stable parachute 17.7 feet in diameter (projected) with a drag coefficient of 1.14 (based on projected diameter) and a towline length of 36.5 feet.

Browman, James S., Jr.↗

Challenging Pneumatic Requirements for Acoustic Testing of the Cryogenic Second Stage for the New Delta 3 Rocket

The paper describes the unique pneumatic test requirements for the acoustic and shock separation testing of the Second Stage for the new Delta III Rocket at the Goddard Space Flight Center in Greenbelt, Maryland. The testing was conducted in the 45,000 cu ft (25-feet wide by 30-feet deep by 50-foot high) Acoustic Facility. The acoustic testing required that the liquid oxygen (LOX) and liquid hydrogen (LH2) tanks be filled with enough liquid nitrogen (LN2) to simulate launch fuel masses during testing. The challenge for this test dealt with designing, procuring, and fabricating the pneumatic supply systems for quick assembly while maintaining the purity requirements and minimizing costs. The pneumatic systems were designed to fill and drain the both LOX and LH2 tanks as well as to operate the fill/drain and vent valves for each of the tanks. The test criteria for the pneumatic sub-systems consisted of function, cleanliness, availability, and cost. The first criteria, function, required the tanks to be filled and drained in an efficient manner while preventing them from seeing pressures greater than 9 psig which would add a pressure cycle to the tank. An LN2 tanker, borrowed from another NASA facility, served as the pre-cool and drain tanker. Pre-cooling the tanks allowed for more efficient and cost effective transfer from the LN2 delivery tankers. Helium gas, supplied from a high purity tube trailer, was used to pressurize the vapor space above the LN2 pushing it into the drain tanker. The tube trailer also supplied high pressure helium to the vehicle for valve control and component purges. Cleanliness was maintained by proper component selection, end-use particle filtration, and any on-site cleaning determined necessary by testing. In order to meet the availability/cost juggling act, products designed for LOX delivery systems were procured to ensure system compatibility while off the shelf valves and tubing designed for the semiconductor industry were procured for the gas systems.

Webb, Andrew T.↗

Magnetic Roots and the Driving of Extended Coronal Heating

We report results from a continuation of a previous study, in which we found large bright coronal loops within active regions and extending from active regions that have one end rooted near an island of included magnetic polarity that is a site of enhanced coronal heating and microflares. This suggested that magnetic activity such as microflaring results in enhanced heating in both the compact core field around the island and in the large loops extending from it. We might expect that the intensity variations due to enhanced heating in the compact and extended structures would be correlated. However, although some ex- tended loops do respond to the largest events taking place in the core fields near their feet, they do not show a clear response to most smaller individual events nor to the overall envelope of coronal heating activity in the core fields at their feet as determined from longer-term observations. Thus, while it is clear that the extended loops' heating is being driven from their ends at the magnetic islands, much of this heating is apparently by some form of footpoint activity that is not strongly coupled to the heating in the footpoint core fields. One possibility is that the remote heating in the extended loops is driven by reconnection at the magnetic null over the island, and that this reconnection is driven mainly by core-field activity that produces little coronal heating within the core field itself, perhaps in the manner of the numerical simulations by Karpen, Antiochos, and DeVore.

Porter, Jason G.↗

Transportation: Destination Mars

As the agency space transportation lead center, Marshall Space Flight Center has been conducting transportation assessments for future robotic and human Mars missions to identify critical technologies. Five human Mars options are currently under assessment with each option including all transportation requirements from Earth to Mars and return. The primary difference for each option is the propulsion source from Earth to Mars. In case any of the options require heavy launch capability that is not currently projected as available, an in-house study has been initiated to determine the most cost effective means of providing such launch capability. This assessment is only considering launch architectures that support the overall human Mars mission cost goal of $25B. The guidelines for the launch capability study included delivery of 80 metric ton (176 KLB) payloads, 25 feet diameter x 92 feet long, to 220 nmi orbits at 28.5 degrees. The launch vehicle concept of the study was designated "Magnum" to differentiate from prior heavy launch vehicle assessments. This assessment along with the assessment of options for all transportation phases of a Mars mission are on-going.

Eoff, Bill↗

A Parametric Study of Accelerations of an Airplane Due to a Wake Vortex System

A study was conducted using strip theory to systematically investigate the effects of progressively more complete descriptions of the interaction of an airplane with a wake vortex system. The emphasis was in roll-dominant, parallel, vortex encounters. That is, the simulated airplane's longitudinal axis was nearly parallel to the rotation axis of the vortex system for most of the results presented. The study began with a drag-less rectangular wing in the flow field of a single vortex and progressed to a complete airplane with aerodynamic surfaces possessing taper, sweep, dihedral, and stalling and immersed in the flow field of a vortex pair in ground effect. The effects of the pitch, roll, and yaw attitudes of the airplane on the calculated accelerations were also investigated. The airplane had the nominal characteristics of a Boeing 757, and the vortex flow field had the nominal characteristics of the wake of a Boeing 767. The Bumham-Hallock model of a vortex flow field was used throughout the study. The data are presented mainly in terms of contours of equal acceleration in a two-dimensional area centered on the vortex pair and having dimensions of 300 feet by 300 feet.

Stewart, Eric C.↗

Assembly of a Full-Scale External Tank Barrel Section Using Friction Stir Welding

A full-scale pathfinder barrel section of the External Tank for the National Aeronautics and Space Administration (NASA) Space Transport System (Space Shuttle) has been assembled at Marshall Space Flight Center (MSFC) via a collaborative effort between NASA/MSFC and Lockheed Martin Michoud Space Systems. The barrel section is 27.5 feet in diameter and 15 feet in height. The barrel was assembled using Super-Light-Weight (SLWT), orthogrid, Al-Li 2195 panel sections and a single longeron panel. A vertical weld tool at MSFC was modified to accommodate FSW and used to assemble the barrel. These modifications included the addition of a FSW weld head and new controller hardware and software, the addition of a backing anvil and the replacement of the clamping system with individually actuated clamps. Weld process 4evelopment was initially conducted to optimize the process for the welds required for completing the assembly. The variable thickness welds in the longeron section were conducted via both two-sided welds and with the use of a retractable pin tool. The barrel assembly was completed in October 1998. Details of the vertical weld tool modifications and the assembly process are presented.

Jones, Chip↗

Reconstruction of the 1994 Pittsburgh Airplane Accident Using a Computer Simulation

On September 8, 1994, a Boeing 737-300 passenger airplane was on a downwind approach to the Pittsburgh International Airport at an altitude of 5000 feet above ground level (6000 feet MSL). While in a shallow left turn onto a downwind approach heading, the airplane crossed into the vortex trail of a Boeing 727 flying in the same approach pattern about 4 miles ahead. The B-737 airplane rolled and turned sharply to the left, exited the vortex wake and plunged into the ground. Weather was not a factor in the accident. The airplane was equipped with a 11+ channel digital Flight Data Recorder (FDR) and a multiple channel Cockpit Voice Recorder (CVR). Both recorders were recovered from the crash site and provided excellent data for the development of an accident scenario. Radar tracking of the two airplanes as well as the indicated air speed (IAS) perturbations clearly visible on the B-737 FDR recordings indicate that the upset was apparently initiated by the airplane's crossing into the wake of the B-727 flying ahead in the same traffic pattern. A 6 degree-of-freedom simulation program for the B-737 airplane using MATLAB and SIMULINK was constructed. The simulation was initialized at the stabilized flight conditions of the airplane about 13 seconds prior to its entry into the vortex trail of the B-727 airplane. By assuming a certain combination of control inputs, it was possible to produce a simulated motion that closely matched that recorded on the FDR.

Parks, Edwin K.↗

Guidance and Control Concepts for the X-33 Technology Demonstrator

The X-33 technology demonstrator is a suborbital precursor to the Reusable Launch Vehicle (RLV) with first flight planned for summer of 1999. The flight test program will include about 15 flights originating from Edwards Air Force Base, California, each with widely varying flight profiles in order to test new thermal protection system (TPS) materials, structures, and linear aerospike engines. The first flights will be relatively short range flights with about a 300 nmi range, maximum Mach number of 7, maximum altitude of 190,000 feet, whereas the latter flights will cover about 800 nmi range, with max altitude of about 260,000 feet and max Mach of about 15. The guidance algorithms must be flexible enough to accommodate these various profiles and to adapt to severe off-nominal dispersions, such as early engine failure (partial or total) where possibly more than half the thrust is lost. An onboard real-time performance monitor will be used to assess the viability of the nominal landing site as well as alternate landing sites that would potentially be used in extreme off-nominal conditions. During ascent, a single entry guidance-related parameter, which is easy to calculate, is used to assess the viability of the nominal landing site as well as alternate landing sites. Real-time adjustment of the stored ascent attitude profile will be performed, as required, to maximize the probability of making it to the nominal landing site. Numerical results are given for various engine-out cases to illustrate the adaptability of the performance monitor.

Dukeman, Gregory A.↗

Anticipatory Postural Activity During Long-Duration Space Flight

Somatosensory input has been used to modify motor output in many contexts. During space flight, the use of the lower limb musculature is much less than during activities in 1g. Consequently the neuromuscular activity of the legs is also reduced during space flight. This decrease in muscle activity contributes to muscle atrophy. Furthermore, adaptations to weightlessness contribute to posture and locomotion problems upon the return to Earth. Providing techniques to counter the negative effects of weightlessness on the neuromuscular system is an important goal, particularly during a long-duration mission. Previous work by our group has shown that lower limb neuromuscular activation that normally precedes arm movements in 1g is absent or greatly reduced during similar movements made while freefloating. However, preliminary evidence indicates that applying pressure to the feet results in enhanced neuromuscular activation during rapid arm movements performed while freefloating. This finding suggests that sensory input can be used to "drive" the motor system to increase neuromuscular functioning throughout a mission. The purpose of this investigation was to quantify the increase in neuromuscular activation resulting from the application of pressure to the feet.

Layne, C. S.↗

Black Carbon (Soot) Aerosol in the Lower Stratosphere and Upper Troposphere

We have used two approaches to measure BCA in the stratosphere. The first method consists of collecting aerosols by impaction on quartz rods, upon which are mounted strips of polystyrene filter material. Each 25 mm by 0.5 mm filter strip is alternately masked and exposed in 5 mm long sections. After sampling, the optical density of the exposed sections is measured and compared with the optical density of the masked (unexposed) sections. The filter strip is a Lambertian collector, the scattering property of which is not affected by the deposition of liquid sulfuric acid droplets which dominate the stratospheric aerosol. Hence, all attenuation greater in the exposed than in the non-exposed sections is due to absorption by BCA or rare opaque materials such as meteoritic iron. In a second approach we expose carbon-coated gold or palladium wires to air outside the aircraft boundary layer [Farlow et al., 1979; Pueschel et al., 1989]. With a field emission scanning electron microscope we are able to characterize BCA particles in addition to the dominant sulfuric acid droplets. Typically, soot is comprised of 20 nm diameter spheres linked together as branching chains or loosely packed aggregates (Figure 1a). The microscope has a lateral image resolution of 1.5 nm and can clearly resolve individual spheres making up BCA aggregates. Their morphology is uniquely different from that of the liquid sulfuric acid-water aerosol (Figure 1b). We approximate the size of each BCA particle by that of a sphere of equivalent volume and fit a lognormal size distribution to both the BCA and H2SO4/H2O aerosols. Both sampler types have been mounted on NASA's ER-2 high-altitude research aircraft (altitude ceiling of 70,000 feet), and on NASA's DC-8 (40,000 feet ceiling) aircraft to sample aerosols from a significant portion of the atmosphere.

Pueschel, R. F.↗

Structural Loading on the QCM/SAW Instrument Aboard the ER-2 Used for Atmospheric Testing

Several experiments have been proposed to capture and evaluate samples of the atmosphere where SST's travel. One means to achieve this is to utilize the quartz crystal microbalance (QCM) / surface acoustical wave (SAW) instrument installed aboard the ER-2, formerly the U-2 reconnaissance aircraft. The QCM is a cascade impactor designed to perform in-situ, real-time measurements of aerosols and chemical vapors at an altitude of 60,000-70,000 feet. The primary use of the ER-2 is by NASA for Earth resources to test new sensor systems before being placed aboard satellites. One of the main reasons the ER-2 is used for this flight experiment is its capability to fly approximately twelve miles above the sea level (can reach an altitude of 78,000 feet). Because the ER-2 operates at such a high altitude, it is of special interest to scientists interested in space exploration or supersonic aircraft. The purpose of some of the experiments is to extinct data from the atmosphere around the ER-2. For the current CSTEA flight experiment, the housing of the QCM is in a frame that connects to an outer pod that attaches to the fuselage of the ER-2. Due to the location of the QCM within the housing frame and the location of the pod on the ER-2, the pod and its contents are subject to structural loads. In addition to structural loads, structural vibrations are also of importance because the QCM output data is based on the determination of beat frequencies between a pair of oscillators (one coated, the second uncoated, according to the chemical reaction being monitored). A structural analysis of this system can indicate whether potential resonances may exist between the (higher) structural modal frequencies and the beat frequencies. In addition undesirable deformations may result due to maximum expected static or dynamic loads during typical flight conditions. If the deformations are excessive they may adversely affect the accuracy the instrumentation output.

Bainum, Peter M.↗

Concept Development of a Mach 1.6 High-Speed Civil Transport

A high-speed civil transport configuration with a Mach number of 1.6 was developed as part of the NASA High-Speed Research Program to serve as a baseline for assessing advanced technologies required for an aircraft with a service entry date of 2005. This configuration offered more favorable solutions to environmental concerns than configurations with higher Mach numbers. The Mach 1.6 configuration was designed for a 6500 n.mi. mission with a 250-passenger payload. The baseline configuration has a wing area of 8732 square feet a takeoff gross weight of 591570 lb, and four 41000-lb advanced turbine bypass engines defined by NASA. These engines have axisymmetric mixer-ejector nozzles that are assumed to yield 20 dB of noise suppression during takeoff, which is assumed to satisfy, the FAR Stage III noise requirements. Any substantial reduction in this assumed level of suppression would require oversizing the engines to meet community noise regulations and would severly impact the gross weight of the aircraft at takeoff. These engines yield a ratio of takeoff thrust to weight of 0.277 and a takeoff wing loading of 67.8 lb/square feet that results in a rotation speed of 169 knots. The approach velocity of the sized configuration at the end of the mission is 131 knots. The baseline configuration was resized with an engine having a projected life of 9000 hr for hot rotating parts and 18000 hr for the rest of the engine, as required for commercial use on an aircraft with a service entry date of 2005. Results show an increase in vehicle takeoff gross weight of approximately 58700 lb. This report presents the details of the configuration development, mass properties, aerodynamic design, propulsion system and integration, mission performance, and sizing.

Shields, Elwood W.↗

An Assessment of Magnetic Conditions for Strong Coronal Heating in Solar Active Regions by Comparing Observed Loops with Computed Potential Field Lines

We report further results on the magnetic origins of coronal heating found from registering coronal images with photospheric vector magnetograms. For two complementary active regions, we use computed potential field lines to examine the global non-potentiality of bright extended coronal loops and the three-dimensional structure of the magnetic field at their feet, and assess the role of these magnetic conditions in the strong coronal heating in these loops. The two active regions are complementary, in that one is globally potential and the other is globally nonpotential, while each is predominantly bipolar, and each has an island of included polarity in its trailing polarity domain. We find the following: (1) The brightest main-arch loops of the globally potential active region are brighter than the brightest main- arch loops of the globally strongly nonpotential active region. (2) In each active region, only a few of the mainarch magnetic loops are strongly heated, and these are all rooted near the island. (3) The end of each main-arch bright loop apparently bifurcates above the island, so that it embraces the island and the magnetic null above the island. (4) At any one time, there are other main-arch magnetic loops that embrace the island in the same manner as do the bright loops but that are not selected for strong coronal heating. (5) There is continual microflaring in sheared core fields around the island, but the main-arch bright loops show little response to these microflares. From these observational and modeling results we draw the following conclusions: (1) The heating of the main-arch bright loops arises mainly from conditions at the island end of these loops and not from their global non-potentiality. (2) There is, at most, only a loose coupling between the coronal heating in the bright loops of the main arch and the coronal heating in the sheared core fields at their feet, although in both the heating is driven by conditions/events in and around the island. (3) The main-arch bright loops are likely to be heated via reconnection driven at the magnetic null over the island. The details of how and where (along the null line) the reconnection is driven determine which of the split-end loops are selected for strong heating. (4) The null does not appear to be directly involved in the heating of the sheared core fields or in the heating of an extended loop rooted in the island. Rather, these all appear to be heated by microflares in the sheared core field.

Gary, G. A.↗

Entrainment of Upper Level Dry Air into Hurricane Earl

Hurricane Earl developed from a tropical wave that moved into the Gulf of Mexico, which triggered abundant convection. On 1 Sept. 1998, the wave was upgraded directly to a tropical storm. Earl reached hurricane status the next morning. The system moved erratically as it interacted with an upper level short wave trough rotating around a long wave trough to the northeast. The storm made landfall near 0600 UTC on 3 September near Panama City, FL. During August and September 1998, NASA conducted the Third Convection and Moisture Experiment (CAMEX-3). It focused on studying the intensity, track, and impacts at landfall of hurricanes. On the afternoon of 2 September 1998, the NASA ER2 high-altitude aircraft flying at 65,000 feet in tandem with the NASA DC-8 flying at 35,000 feet flew over and through, respectively, the eastern rainbands of Earl near the Florida Panhandle as the storm neared landfall in the region. Two approaches to studying Earl are undertaken here: first, an examination of the source and height of the dry air region using GOES-8 water vapor data and, second, a look into the impact of the dry air entrainment on the system using aircraft remote sensing data.

Guillory, Anthony R.↗

XTE J1906+09 Observations with RXTE

The 89 s pulsar XTE J1906+09 was serendipitously discovered in a 1996 observation of the soft gamma repeater SGR 1900+14. Two outbursts, in 1996 September and 1998 September have been reported to date. Since this system appears to be transient, it is likely in a Be/X-ray binary, accreting material from a circumstellar disk around its companion. Preliminary pulse timing analyses of RXTE data from the 1998 September outburst revealed an orbital signature consistent with either (i) a low-eccentricity, short period orbit, similar to OAO 1657-415 or (ii) periastron passage in a longer orbital period, higher eccentricity Be/X-ray binary system. No companion has been identified to date due to the large 2 feet error radius of the current best position. SGR 1900+14 has been regularly monitored with RXTE since 1998. Because XTE J1906+09 is only 33 feet away, it often shares the RXTE/PCA field of view with SGR 1900+14, giving us a large number of archival PCA observations. We will present results of a search of RXTE data for outbursts of XTE 1906+09, including histories of pulse frequency, 2-30 keV intensity, pulse profiles, and energy spectra. Results of a pulse timing analysis of the detected outbursts will also be presented.

Wilson, Colleen A.↗

Structural Analysis of the QCM Aboard the ER-2

As a result of recent supersonic transport (SST) studies on the effect they may have on the atmosphere, several experiments have been proposed to capture and evaluate samples of the stratosphere where SST's travel. One means to achieve this is to utilize the quartz crystal microbalance (QCM) installed aboard the ER-2, formerly the U-2 reconnaissance aircraft. The QCM is a cascade impactor designed to perform in-situ, real-time measurements of aerosols and chemical vapors at an altitude of 60,000 - 70,000 feet. The ER-2 is primarily used by NASA for Earth resources to test new sensor systems before they are placed aboard satellites. One of the main reasons the ER-2 is used for this flight experiment is its capability to fly approximately twelve miles above sea level (can reach an altitude of 78,000 feet). Because the ER-2 operates at such a high altitude, it is of special interest to scientists interested in space exploration or supersonic aircraft. Some of the experiments are designed to extract data from the atmosphere around the ER-2. For the current flight experiment, the QCM is housed in a frame that is connected to an outer pod that is attached to the fuselage of the ER-2. Due to the location of the QCM within the housing frame and the location of the pod on the ER-2, the pod and its contents are subject to structural loads. In addition to structural loads, structural vibrations are also of importance because the QCM is a frequency induced instrument. Therefore, a structural analysis of the instrument within the frame is imperative to determine if resonance and/or undesirable deformations occur.

Jones, Phyllis D.↗

Use of Vertical Lift Planetary Aerial Vehicles for the Exploration of Mars

Despite the thin, cold, carbon dioxide-based atmosphere of Mars, recent work at NASA Ames has suggested that vertical lift (based on rotary-wing technology) planetary aerial vehicles could potentially be developed to support Mars exploration missions. The use of robotic vertical lift planetary aerial vehicles (VL PAVs) would greatly augment the science return potential of Mars exploration. Many technical challenges exist in the development of vertical lift vehicles for planetary exploration. It only takes the realization that the world altitude record for a helicopter is less than 40,000 feet (versus flight at the equivalent terrestrial altitude of over 100,000 feet required to match Mars' surface atmospheric density) to appreciate the aeronautical challenges in developing these vehicles. Nonetheless, preliminary work undertaken at NASA Ames and others suggest that these vehicles are indeed viable candidates for Mars exploration.

Young, L. A.↗