Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Eutectic system”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Thermo mechanical analysis of fully ceramic microencapsulated fuel during in-pile operation

A proposed fuel for improved performance in LWRs (Light Water Reactors) is FCM (fully encapsulated micro-ceramic) fuel concept that involves TRISO (Tri-structural-Isotropic) fuel particles embedded in a NITE (Nano Infiltrated Eutectic) silicon carbide matrix. TRISO fuel particles contain a spherical fuel kernel that will likely range from about 500 to in excess of 800 μm in diameter. The kernel and buffer layer are then typically coated with 3 isotropic layers consisting of a dense inner pyrolytic carbon (IPyC), a silicon carbide (SiC) layer, and an outer layer of dense, pyrolytic carbon (OPyC). These layers are typically around 40 μm thick, but can range from 20 to 60 μm. The TRISO particle packing fraction in the NITE-SiC matrix is expected to be 40-45 vol.%. The release of radioactivity into the coolant is dependent on the integrity of the silicon carbide layer of the TRISO particles and the NITE-SiC matrix. BISON, a code under development by Idaho National Laboratory, has been built on the Multi-physics Object Oriented Simulation Environment (MOOSE). MOOSE is a massively parallel, finite element computational system that uses a Jacobian-free, Newton-Krylov (JFNK) method to solve coupled systems and non-linear partial differential equations. A single particle comparison to fuel performance codes such as PARFUME was conducted and demonstrated that BISON is able to simulate the required physics. FCM pellets embedded with homogenous particles were simulated. It was found that the interior matrix temperature was predicted to be considerably lower than for an equivalent UO{sub 2} pellet. The swelling dependence on temperature created a compressive region around the perimeter of the pellet. However, at fluences above 6.10{sup 25} neutrons/m{sup 2}, the swelling of the pyrolytic carbon might cause significant tensile stresses and possible cracks near the surface of the pellet. This suggests that the pyrolytic carbon swelling may be an important factor in the lifetime of this fuel type.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effects of a refractory metal protective barrier on uranium carbonitride ceramic–metallic composites exposed to a high temperature hydrogen environment

Uranium nitride has been under consideration at NASA and the Department of Energy for nuclear thermal propulsion applications intended for deep space exploration vehicles. It is critical to the success of the technology development that the behavior of the fuel system is properly characterized in operational environments. This body of work fabricated ceramic metal composites consisting of uranium ceramic fuel in a molybdenum and molybdenum–tungsten metal matrix, both with and without an exterior molybdenum barrier. Specimens were introduced to a high temperature hydrogen environment and characterized through x-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy to identify characteristic changes. A portion of the specimens was fabricated with a 1.27 mm thick molybdenum barrier in order to isolate the material from the hydrogen environment. Instability of the uranium nitride occurred as low as 2073 K, leading to aggressive instability approaching 2658 K. Carbon reactions with the metal matrix were observed as well as alloying between the uranium and metal matrix constituents. The liquid uranium resulting from the instability of the uranium nitride was observed to attack the grain boundaries of the refractory metal, resulting in the formation of a liquid uranium molybdenum eutectic melt. Specimens encased in a barrier experienced similar results. The authors conclude this is a significant challenge to applications of this cermet at these temperatures. Alternate configurations with resilient hermetic seals or lower temperature applications such as power reactors may have more success.

36 MATERIALS SCIENCE↗

Intermediate Temperature Fluids Life Tests - Experiments

There are a number of different applications that could use heat pipes or loop heat pipes (LHPs) in the intermediate temperature range of 450 to 725 K (170 to 450 C), including space nuclear power system radiators, fuel cells, and high temperature electronics cooling. Historically, water has been used in heat pipes at temperatures up to about 425 K (150 C). Recent life tests, updated below, demonstrate that titanium/water and Monel/water heat pipes can be used at temperatures up to 550 K (277 C), due to water's favorable transport properties. At temperatures above roughly 570 K (300 C), water is no longer a suitable fluid, due to high vapor pressure and low surface tension as the critical point is approached. At higher temperatures, another working fluid/envelope combination is required, either an organic or halide working fluid. An electromotive force method was used to predict the compatibility of halide working fluids with envelope materials. This procedure was used to reject aluminum and aluminum alloys as envelope materials, due to their high decomposition potential. Titanium and three corrosion resistant superalloys were chosen as envelope materials. Life tests were conducted with these envelopes and six different working fluids: AlBr3, GaCl3, SnCl4, TiCl4, TiBr4, and eutectic diphenyl/diphenyl oxide (Therminol VP-1/Dowtherm A). All of the life tests except for the GaCl3 are ongoing; the GaCl3 was incompatible. As the temperature approaches 725 K (450 C), cesium is a potential heat pipe working fluid. Life tests results are also presented for cesium/Monel 400 and cesium/70-30 copper/nickel heat pipes operating near 750 K (477 C). These materials are not suitable for long term operation, due to copper transport from the condenser to the evaporator.

Anderson, William G.↗

A Brief Review of Past INL Work Assessing Radionuclide Content in TMI-2 Melted Fuel Debris: The Use of 144 Ce as a Surrogate for Pu Accountancy

This report serves as a literature review of prior work performed at Idaho National Laboratory, and its predecessor organizations Idaho National Engineering Laboratory (INEL) and Idaho National Engineering and Environmental Laboratory (INEEL), studying radionuclide partitioning within the melted fuel debris of the reactor of the Three Mile Island 2 (TMI-2) nuclear power plant. The purpose of this review is to document prior published work that provides supporting evidence of the utility of using 144 Ce as a surrogate for plutonium within melted fuel debris. When the TMI-2 accident occurred no quantitative nondestructive analysis (NDA) techniques existed that could assay plutonium in the unconventional wastes from the reactor. However, unpublished work performed at INL by D. W. Akers in the late 1980s through the 1990s demonstrated that passive gamma-ray spectrometry of 144 Ce could potentially be used to develop a semi-quantitative correlation for estimating plutonium content in these materials. The fate and transport of radioisotopes in fuel from different regions of the core, including uranium, fission products, and actinides, appear to be well characterized based on the maximum temperature reached by fuel in different parts of the core and the melting point, boiling point, and volatility of those radioisotopes. Also, the chemical interactions between fuel, fuel cladding, control elements, and core structural components appears to have played a large role in determining when and how fuel relocation occurred in the core; perhaps the most important of these reaction appears to be related to the formation of mixed-material alloys, eutectics, in the fuel cladding. Because of its high melting point, low volatility, and similar chemical behavior to plutonium, the element cerium appears to have behaved similarly to plutonium during the evolution of the TMI-2 accident. Anecdotal evidence extrapolated from open-source literature strengthens this logical feasibility for using cerium, which is rather easy to analyze using passive nondestructive analysis gamma-ray spectrometry, as a surrogate for plutonium in the final analysis of TMI-2 melted fuel debris. The generation of this report is motivated by the need to perform nuclear material accountancy measurements on the melted fuel debris that will be excavated from the damaged nuclear reactors at the Fukushima Daiichi nuclear power plant in Japan, which were destroyed by the Tohoku earthquake and tsunami on March 11, 2011. Lessons may be taken from prior U.S. work related to the study of the TMI-2 core debris to support the development of new assay methods for use at Fukushima Daiichi. While significant differences exist between the two reactor systems (pressurized water reactor (TMI-2) versus boiling water reactor (FD), fresh water post-accident cooing (TMI-2) versus salt water (FD), maintained containment (TMI-2) versus loss of containment (FD)) there remain sufficient similarities to motivate these comparisons.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Characterization of an aluminum alloy hemispherical shell fabricated via direct metal laser melting

The ability of additive manufacturing to directly fabricate complex shapes provides characterization challenges for part qualification. The orientation of the microstructures produced by these processes will change relative to the surface normal of a complex part. In this work, the microscopy and x-ray tomography of an AlSi10Mg alloy hemispherical shell fabricated using powder bed metal additive manufacturing are used to illustrate some of these challenges. The shell was manufactured using an EOS M280 system in combination with EOS-specified powder and process parameters. The layer-by-layer process of building the shell with the powder bed additive manufacturing approach results in a position-dependent microstructure that continuously changes its orientation relative to the shell surface normal. X-ray tomography was utilized to examine the position-dependent size and distribution of porosity and surface roughness in the 98.6% dense part. Optical and electron microscopy were used to identify global and local position-dependent structures, grain morphologies, chemistry, and precipitate sizes and distributions. The rapid solidification processes within the fusion zone (FZ) after the laser transit results in a small dendrite size. Cell spacings taken from the structure in the middle of the FZ were used with published relationships to estimate a cooling rate of ~9 × 10 5 K/s. Uniformly-distributed, nanoscale Si precipitates were found within the primary α-Al grains. A thin, distinct boundary layer containing larger α-Al grains and extended regions of the nanocrystalline divorced eutectic material surrounds the FZ. Moreover, subtle differences in the composition between the latter layer and the interior of the FZ were noted with scanning transmission electron microscopy (STEM) spectral imaging.

36 MATERIALS SCIENCE↗

Size dependence of microstructure of AlSi10Mg alloy fabricated by selective laser melting

Highlights: • Plate-shaped samples with various widths were fabricated via selective laser melting. • The hardness of AlSi10Mg samples slightly decreased with decreasing sample width. • The alloy sample size had a slight effect on microstructure of the α-Al matrix. • Precipitation of Si phase in α-Al matrix was enhanced by reducing the sample size. • The softening by reducing sample size is likely due to their slower cooling rate. - Abstract: In order to investigate the size dependence of microstructure of the AlSi10Mg alloy fabricated by selective laser melting (SLM) combined with a powder bed technique, plate-shaped AlSi10Mg alloy samples with various widths (ranging from approximately 10 mm to 0.3 mm) were produced in this study. All the fabricated samples exhibited characteristic microstructural morphologies consisting of melt pools with columnar α-Al grains surrounded by fine eutectic Si particles, whereas their sample sizes had a relatively small effect on the texture and average grain size of the α-Al matrix. However, the formation of fine Si precipitates inside the columnar α-Al grains was observed more often for the smaller-sized samples, which could be a possible dominant contributor to the observed softening of the sample by reducing sample size. The obtained results were utilized for discussing the size dependence of the strength of the SLM-manufactured porous alloy samples.

36 MATERIALS SCIENCE↗

Low cycle fatigue behavior of AlSi10Mg(Cu) alloy at high temperature

Highlights: • The cyclic stress response of AlSi10Mg(Cu) alloy in LCF regime is temperature-dependent. • Precipitates transitions were observed after high temperature cycle loading. • Changes in the interaction mechanism between dislocations and nanoparticles lead to different cyclic stress responses. - Abstract: Low cycle fatigue (LCF) behavior of AlSi10Mg(Cu) alloy was investigated at 100 °C and 250 °C over a range of strain amplitude from 0.25% to 0.40%. Cycle stress response, hysteresis loops, fatigue life, as well as post-fatigue microstructure were studied in detail. Except 0.25%, the alloy performed cycle hardening behavior at 100 °C and softening behavior at 250 °C at any given strain amplitude, which corresponded well with the observed phenomena in hysteresis loops. At any given temperature, cyclic stress increases while fatigue life decreases with the increasing strain amplitude. The fatigue life of the studied alloy at 100 °C was higher than that at 250 °C under the same strain amplitude. Fractography indicated that most fatigue crack initiated from casting defects. The fatigue crack propagation was mainly characterized by fatigue striations and tear ridges in any conditions. Section inspection shows that the number of cracked eutectic Si increases with decreasing the temperature or increasing strain amplitude. Post-mortem transmission electron microscopy (TEM) investigations indicated that cyclic hardening behavior at 100 °C was due to the pinning effect of coherent precipitates (β″-Mg{sub 2}Si and GP zones). Most of tiny coherency precipitates and clusters transformed to large semi-coherency Q′ and β′-Mg{sub 2}Si precipitates after cyclic loading at 250 °C, leading to the sharp decrease of pinning number and dislocation density, which is a key reason for the cyclic softening. Another factor is that more dislocations can be activated and dislocation climb is easier at higher temperature.

36 MATERIALS SCIENCE↗

Heat Transfer and Latent Heat Storage in Inorganic Molten Salts for Concentrating Solar Power Plants

A key technological issue facing the success of future Concentrating Solar Thermal Power (CSP) plants is creating an economical Thermal Energy Storage (TES) system. Current TES systems use either sensible heat in fluids such as oil, or molten salts, or use thermal stratification in a dual-media consisting of a solid and a heat-transfer fluid. However, utilizing the heat of fusion in inorganic molten salt mixtures in addition to sensible heat, as in a Phase change material (PCM)-based TES, can significantly increase the energy density of storage requiring less salt and smaller containers. A major issue that is preventing the commercial use of PCM-based TES is that it is difficult to discharge the latent heat stored in the PCM melt. This is because when heat is extracted, the melt solidifies onto the heat exchanger surface decreasing the heat transfer. Even a few millimeters of thickness of solid material on heat transfer surface results in a large drop in heat transfer due to the low thermal conductivity of solid PCM. Thus, to maintain the desired heat rate, the heat exchange area must be large which increases cost. This project demonstrated that the heat transfer coefficient can be increase ten-fold by using forced convection by pumping a hyper-eutectic salt mixture over specially coated heat exchanger tubes. However, only 15% of the latent heat is used against a goal of 40% resulting in a projected cost savings of only 17% against a goal of 30%. Based on the failure mode effect analysis and experience with pumping salt at near freezing point significant care must be used during operation which can increase the operating costs. Therefore, we conclude the savings are marginal to justify using this concept for PCM-TES over a two-tank TES. The report documents the specialty coatings, the composition and morphology of hypereutectic salt mixtures and the results from the experiment conducted with the active heat exchanger along with the lessons learnt during experimentation.

14 SOLAR ENERGY↗

Examination of Liquid Fluoride Salt Heat Transfer

The need for high efficiency power conversion and energy transport systems is increasing as world energy use continues to increase, petroleum supplies decrease, and global warming concerns become more prevalent. There are few heat transport fluids capable of operating above about 600oC that do not require operation at extremely high pressures. Liquid fluoride salts are an exception to that limitation. Fluoride salts have very high boiling points, can operate at high temperatures and low pressures and have very good heat transfer properties. They have been proposed as coolants for next generation fission reactor systems, as coolants for fusion reactor blankets, and as thermal storage media for solar power systems. In each case, these salts are used to either extract or deliver heat through heat exchange equipment, and in order to design this equipment, liquid salt heat transfer must be predicted. This paper discusses the heat transfer characteristics of liquid fluoride salts. Historically, heat transfer in fluoride salts has been assumed to be consistent with that of conventional fluids (air, water, etc.), and correlations used for predicting heat transfer performance of all fluoride salts have been the same or similar to those used for water conventional fluids an, water, etc). A review of existing liquid salt heat transfer data is presented, summarized, and evaluated on a consistent basis. Less than 10 experimental data sets have been found in the literature, with varying degrees of experimental detail and measured parameters provided. The data has been digitized and a limited database has been assembled and compared to existing heat transfer correlations. Results vary as well, with some data sets following traditional correlations; in others the comparisons are less conclusive. This is especially the case for less common salt/materials combinations, and suggests that additional heat transfer data may be needed when using specific salt eutectics in heat transfer equipment designs. All of the data discussed above were taken under forced convective conditions (both laminar and turbulent). Some recent data taken at ORNL under free convection conditions are also presented and results discussed. This data was taken using a simple crucible experiment with an instrumented nickel heater inserted in the salt to induce natural circulation within the crucible. The data was taken over a temperature range of 550oC to 650oC in FLiNaK salt. This data covers both laminar and turbulent natural convection conditions, and is compared to existing forms of natural circulation correlations.

experiments↗

Tritium aspects of the fusion nuclear science facility

The Fusion Nuclear Science Facility (FNSF) is intended to bridge the technical gaps from ITER to DEMO, and provide a fully nuclear environment for the advancement of materials and blanket science, among other missions. Though smaller (~500 MW fusion power) than the envisioned DEMO, our FNSF design still seeks to test DEMO-relevant components and technologies, and to that end one of its goals is to achieve a tritium breeding ratio near one using a dual-cooled lead lithium (DCLL) blanket. We explore here the migration of bred tritium through in-vessel components and coolant loops, which is exacerbated by the relatively low solubility of tritium in PbLi and the high operating temperatures envisioned in later phases of operation. Some features inherent to the design of the DCLL help limit tritium losses, namely the relatively high PbLi flow rates; coupled with efficient tritium extraction, the DCLL potentially achieves low tritium permeation losses without the use of permeation barriers. We outline here the design of such an extraction system, and some of the materials challenges that must be met in order to realize it. The efficacy of these and other design features, such as coaxial piping, is demonstrated via a series of parameter studies. We also investigate the effect of parameter uncertainties, and find that the imprecise knowledge of the tritium solubility in PbLi in particular leads to very disparate estimates of tritium losses. Depending on the experimental value used, losses range from ~0.05 to over 6 grams of tritium per year. As a result, the former is acceptable based on estimated environmental releases and resultant dose to members of the public; the latter exceeds regulatory limits.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Combining High-Throughput Experiments and Active Learning to Characterize Deep Eutectic Solvents

The high tunability of deep eutectic solvents (DESs) stems from the ease of changing their precursors and relative compositions. However, measuring the physicochemical properties across large composition and temperature ranges, necessary to properly design target-specific DESs, is tedious and error-prone and represents a bottleneck in the advancement and scalability of DES-based applications. As such, active learning (AL) methodologies based on Gaussian processes (GPs) were developed in this work to minimize the experimental effort necessary to characterize DESs. Owing to its importance for large-scale applications, the reduction of DES viscosity through the addition of a low-molecular-weight solvent was explored as a case study. A high-throughput experimental screening was initially performed on nine different ternary DESs. Then, GPs were successfully trained to predict DES viscosity from its composition and temperature, showcasing the ability of these stochastic, nonparametric models to accurately describe the physicochemical properties of complex mixtures. Finally, the ability of GPs to provide estimates of their own uncertainty was leveraged through an AL framework to minimize the number of data points necessary to obtain accurate viscosity modes. This led to a significant reduction in data requirements, with many systems requiring only five independent viscosity data points to be properly described.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Deep Eutectic Solvents for Efficient Fractionation of Lignocellulose to Produce Uncondensed Lignin and High-Quality Cellulose

Simultaneously inhibiting lignin condensation and cellulose degradation remains a major challenge for achieving holistic valorization of lignocellulose. Here, we developed a deep eutectic solvent (DES), composed of l-cysteine (Cys) and lactic acid (LA), to fractionate both uncondensed lignin and high-quality cellulose from eucalyptus wood by leveraging the unique properties of Cys, i.e., highly nucleophilic groups (–SH) and hydrogen bond acceptor/donor groups (–NH 2 and –COOH). The nucleophilic –SH in Cys effectively quenches the benzylic carbocations (C α + ions, formed at the benzylic sites of lignin) that lead to lignin condensation. This enables the high yield of uncondensed lignin (81%) with high retention of β–O–4 bonds (up to 90%). The separated uncondensed lignin is further depolymerized to prepare monophenols in a satisfactory 43% yield, equivalent to 73% of the theoretical yield. Moreover, the –NH 2 and –COOH groups in Cys form extensive hydrogen bonds with the hydroxyl groups in cellulose, thus decreasing the interaction energy of DES on cellulose. As a result, the cellulose achieves an astonishing 99% retention and maintains a high degree of polymerization of 1160. The obtained high-quality cellulose is further conversed into cellulose nanofibers for strong and transparent films. Furthermore, this study provides new insights into the efficient separation of uncondensed lignin and high-quality cellulose from lignocellulose by a novel DES system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Prediction of solubility parameters of lignin and ionic liquids using multi-resolution simulation approaches

The solubility parameter (SP) of a molecular species is a vital feature that indicates polarity and quantifies the ‘like-seeks-like’ principle, which is used in chemistry to screen solvents for dissolution. Recent studies have demonstrated that ionic liquids (ILs) and deep eutectic solvents (DESs) efficiently solubilize lignocellulosic biomass and promote enzymatic saccharification into sugars used for the production of biofuels and value-added chemicals. Understanding the solubility of plant biopolymers, particularly lignin, in ILs and DESs is critical for selecting candidate ILs and DESs for biomass pretreatment; however, experimentally measuring SPs is challenging. Thus, the present study investigates lignin dissolution mechanisms in IL/DES and prediction of the solubility parameters (Hildebrand and Hansen) of lignin, ILs, and DESs using multi-resolution simulation approaches. Here, solubility parameters of the studied compounds were predicted using molecular dynamics (MD) simulations, and the SP of lignin was determined to be 23–27 MPa 1/2 , which was close to the polymeric lignin solubility parameter (24.3–25.5 MPa 1/2 ). The SPs of ILs namely [Ch][Lys], [Ch][Oct], and [Emim][Lys] were predicted to be ~26 MPa 1/2 , which is close to lignin's SPs and resulted in increased biomass delignification. The MD simulated SPs were validated by both the COSMO-RS model and experimental investigations, with the results showing a close agreement between the predicted and experimentally obtained SPs. In addition, the enthalpy of vaporization (ΔH vap ) of ILs/DESs was predicted based on the potential energy of the system, and the ΔH vap of ILs/DESs was around 40–65 kcal mol –1 , which is 5–8 times higher than that of traditional organic solvents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

New Effective Material Couple--Oxide Ceramic and Carbon Nanotube-- Developed for Aerospace Microsystem and Micromachine Technologies

The prime driving force for using microsystem and micromachine technologies in transport vehicles, such as spacecraft, aircraft, and automobiles, is to reduce the weight, power consumption, and volume of components and systems to lower costs and increase affordability and reliability. However, a number of specific issues need to be addressed with respect to using microsystems and micromachines in aerospace applications--such as the lack of understanding of material characteristics; methods for producing and testing the materials in small batches; the limited proven durability and lifetime of current microcomponents, packaging, and interconnections; a cultural change with respect to system designs; and the use of embedded software, which will require new product assurance guidelines. In regards to material characteristics, there are significant adhesion, friction, and wear issues in using microdevices. Because these issues are directly related to surface phenomena, they cannot be scaled down linearly and they become increasingly important as the devices become smaller. When microsystems have contacting surfaces in relative motion, the adhesion and friction affect performance, energy consumption, wear damage, maintenance, lifetime and catastrophic failure, and reliability. Ceramics, for the most part, do not have inherently good friction and wear properties. For example, coefficients of friction in excess of 0.7 have been reported for ceramics and ceramic composite materials. Under Alternate Fuels Foundation Technologies funding, two-phase oxide ceramics developed for superior high-temperature wear resistance in NASA's High Operating Temperature Propulsion Components (HOTPC) project and new two-layered carbon nanotube (CNT) coatings (CNT topcoat/iron bondcoat/quartz substrate) developed in NASA's Revolutionary Aeropropulsion Concepts (RAC) project have been chosen as a materials couple for aerospace applications, including micromachines, in the nanotechnology lubrication task because of their potential for superior friction and wearf properties in air and in an ultrahigh vacuum, spacelike environment. At the NASA Glenn Research Center, two-phase oxide ceramic eutectics, Al2O3/ZrO2(Y2O3), were directionally solidified using the laser-float-zone process, and carbon nanotubes were synthesized within a high-temperature tube furnace at 800 C. Physical vapor deposition was used to coat all quartz substrates with 5-nm-thick iron as catalyst and bondcoat, which formed iron islands resembling droplets and serving as catalyst particles on the quartz. A series of scanning electron micrographs showing multiwalled carbon nanotubes directionally grown as aligned "nanograss" on quartz is presented. Unidirectional sliding friction eperiments were conducted at Glenn with the two-layered CNT coatings in contact with the two-phase Al2O3/ZrO2(Y2O3) eutectics in air and in ultrachigh vacuum. The main criteria for judging the performance of the materials couple for solid lubrication and antistick applications in a space environment were the coefficient of friction and the wear resistance (reciprocal of wear rate), which had to be less than 0.2 and greater than 10(exp 5) N(raised dot)/cubic millimetes, respectively, in ultrahigh vacuum. In air, the coefficient of friction for the CNT coatings in contact with Al2O3/ZrO2 (Y2O3) eutectics was 0.04, one-fourth of that for quartz. In an ultrahigh vacuum, the coefficient of friction for CNT coatings in contact with Al2O3/ZrO2 (Y2O3) was one-third of that for quartz. The two-phase Al2O3/ZrO2 (Y2O3) eutectic coupled with the two-layered CNT coating met the coefficient of friction and wear resistance criteria both in air and in an ultrahigh vacuum, spacelike environment. This material's couple can dramatically improve the stiction (or adhesion), friction, and wear resistance of the contacting surfaces, which are major issues for microdevices and micromachines.

Miyoshi, Kazuhisa↗

Effect of Viscosity of a Deep Eutectic Solvent on CO 2 Capture Performance in an Energy-Efficient Membrane Contactor-Based Process

Greenhouse gas contributions to climate change have driven intense interest in the separation of CO 2 from wet flue gas streams. Deep eutectic solvents (DESs) are an emerging class of highly selective CO 2 absorbents. A prototypical DES, reline, is a mixture of choline chloride and urea. Reline is a thermally stable, nontoxic, and biodegradable solvent with negligible volatility and is inexpensive. We demonstrate a scalable and energy-efficient hollow fiber membrane contactor (HFMC)-based process using a green solvent for CO 2 capture. This process uses reline in HFMC to provide close interfacial interactions and contact between DES and CO 2 . This approach overcomes the disadvantages associated with direct absorption in DES and could potentially be applied to a variety of solvent-based CO 2 capture methods. Commercial, low-cost polymer hollow fiber membranes were evaluated for the capture of CO 2 with reline. From a mixed gas containing N 2 and CO 2 , the DES-based HFMC separated CO 2 with a purity of 97 mol %. The effect of the viscosity of reline on the CO 2 capture performance was investigated by adding water to the reline. The addition of water to reline significantly reduced its viscosity, which led to a permeate flux of 170 mmol/(m 2 ·h) at 35 °C, 4 bar, and 60 wt % water in solvent, which was approximately 8 times higher than that of the pure reline in the membrane contactor system. In situ Fourier transform infrared spectroscopy and nuclear magnetic resonance (NMR) revealed that reline absorbs CO 2 by physical absorption without forming new chemical compounds and that CO 2 separation by reline occurs via the pressure swing mechanism. This research provides fundamental insights about green physical solvent-based separation processes and a pathway toward industrial deployment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Au-assisted molecular beam epitaxy of InAs nanowires: Growth and theoretical analysis

The Au-assisted molecular beam epitaxial growth of InAs nanowires is discussed. In situ reflection high-energy electron diffraction observations of phase transitions of the catalyst particles indicate that they can be liquid below the eutectic point of the Au-In alloy. The temperature range where the catalyst can be liquid covers the range where we observed nanowire formation (380-430 deg. C). The variation of nanowire growth rate with temperature is investigated. Pure axial nanowire growth is observed at high temperature while mixed axial/lateral growth occurs at low temperature. The change of the InAs nanowire shape with growth duration is studied. It is shown that significant lateral growth of the lower part of the nanowire starts when its length exceeds a critical value, so that their shape presents a steplike profile along their axis. A theoretical model is proposed to explain the nanowire morphology as a result of the axial and lateral contributions of the nanowire growth.

36 MATERIALS SCIENCE↗

Effect of Bi on the microstructure and mechanical properties of Sn-Zn alloys processed by rolling

Highlights: • Sn-Zn-Bi is proposed for the first time as the cladding in linear explosive device. • Bi can significantly refine the microstructure of Sn-Zn. • Bi can enhance both strength and ductility of Sn-Zn processed by rolling. • The 5 wt% Bi in Sn-3Zn leads to finest and most homogenous grains after rolling. - Abstract: Sn-Zn based alloys including Sn-3Zn, Sn-3Zn-1Bi, and Sn-3Zn-5Bi were prepared by casting and rolling, in efforts to assess their feasibility for the application as cladding materials in detonating and explosive cords. It was found that Bi significantly refined the solidification microstructure, changing the configuration of Sn-Zn eutectic from well-aligned Zn-rich precipitates/needles to misaligned Zn-rich flakes. During deformation, second phases like Zn-rich precipitates and Bi particles, and Bi solutes were effective in grain refinement since second phase particles provided more sites for nucleation and more obstacles to growth of new recrystallized grains. Tensile results revealed that Bi addition enhanced both strength and ductility of the rolled Sn-Zn-Bi alloys. The Sn-3Zn-5Bi alloy possessed superior strength and ductility (UTS: 84.4 MPa; Yield strength: 68.3 MPa; Elongation: 75.2%) due to its finest and most homogeneous equiaxed grains. Based on decent mechanical properties, the Sn-Zn-Bi alloys could be well qualified for the application as cladding materials.

36 MATERIALS SCIENCE↗

Microphase separation in copolymers of hydrophilic PEG blocks and hydrophobic tyrosine-derived segments using simultaneous SAXS/WAXS/DSC

Hydration- and temperature-induced microphase separations were investigated by simultaneous small- and wide-angle X-ray scattering (SAXS and WAXS) and differential scanning calorimetry (DSC) in a family of copolymers in which hydrophilic poly(ethylene glycol) (PEG) blocks are inserted randomly into a hydrophobic polymer made of either desaminotyrosyl-tyrosine ethyl ester (DTE) or iodinated I{sub 2}DTE segments. Iodination of the tyrosine rings in I{sub 2}DTE increased the X-ray contrast between the hydrophobic and hydrophilic segments in addition to facilitating the study of the effect of iodination on microphase separation. The formation of phase-separated, hydrated PEG domains is of considerable significance as it profoundly affects the polymer properties. The copolymers of DTE (or I{sub 2}DTE) and PEG are a useful model system, and the findings presented here may be applicable to other PEG-containing random copolymers. In copolymers of PEG and DTE and I{sub 2}DTE, the presence of PEG depressed the glass transition temperature (T{sub g}) of the copolymer relative to the homopolymer, poly(DTE carbonate), and the DTE/I{sub 2}DTE segments hindered the crystallization of the PEG segments. In the dry state, at large PEG fractions (>70 vol%), the PEG domains self-assembled into an ordered structure with 14-18 nm distance between the domains. These domains gave rise to a SAXS peak at all temperatures in the iodinated polymers, but only above the T{sub g} in non-iodinated polymers, due to the unexpected contrast-match between the crystalline PEG domains and the glassy DTE segments. Irrespective of whether PEG was crystalline or not, immersion of these copolymers in water resulted in the formation of hydrated PEG domains that were 10-20 nm apart. Since both water and the polymer chains must be mobile for the phase separation to occur, the PEG domains disappeared when the water froze, and reappeared as the ice began to melt. This transformation was reversible, and showed hysteresis as did the melting of ice and freezing of the water incorporated into the polymer. PEG-water complexes and PEG-water eutectics were observed in WAXS and DSC scans, respectively.

36 MATERIALS SCIENCE↗