Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engineering method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

A Three-Dimensional Solution of Flows over Wings with Leading-Edge Vortex Separation. Part 1: Engineering Document

A method of predicting forces, moments, and detailed surface pressures on thin, sharp-edged wings with leading-edge vortex separation in incompressible flow is presented. The method employs an inviscid flow model in which the wing and the rolled-up vortex sheets are represented by piecewise, continuous quadratic doublet sheet distributions. The Kutta condition is imposed on all wing edges. Computed results are compared with experimental data and with the predictions of the leading-edge suction analogy for a selected number of wing planforms over a wide range of angle of attack. These comparisons show the method to be very promising, capable of producing not only force predictions, but also accurate predictions of detailed surface pressure distributions, loads, and moments.

Brune, G. W.↗
NASA NTRS1981

Preliminary study of temperature measurement techniques for Stirling engine reciprocating seals

Methods of determining the contact surface temperature in reciprocating seals are investigated. Direct infrared measurement of surface temperatures of a rod exiting a loaded cap seal or simulated seal are compared with surface thermocouple measurements. Significant cooling of the surface requires several milliseconds so that exit temperatures may be considered representative of internal contact temperatures.

Wilcock, D. F.↗
NASA NTRS1933

Rates of fuel discharge as affected by the design of fuel-injection systems for internal-combustion engines

Using the method of weighing fuel collected in a receiver during a definite interval of the injection period, rates of discharge were determined, and the effects noted, when various changes were made in a fuel-injection system. The injection system consisted primarily of a by-pass controlled fuel pump and an automatic injection valve. The variables of the system studied were the pump speed, pump-throttle setting, discharge-orifice diameter, injection-valve opening and closing pressures, and injection-tube length and diameter.

Gelalles, A G↗
NASA NTRS2004

Intelligent, Robust Control of Deteriorated Turbofan Engines via Linear Parameter Varying Quadratic Lyapunov Function Design

A method for accommodating engine deterioration via a scheduled Linear Parameter Varying Quadratic Lyapunov Function (LPVQLF)-Based controller is presented. The LPVQLF design methodology provides a means for developing unconditionally stable, robust control of Linear Parameter Varying (LPV) systems. The controller is scheduled on the Engine Deterioration Index, a function of estimated parameters that relate to engine health, and is computed using a multilayer feedforward neural network. Acceptable thrust response and tight control of exhaust gas temperature (EGT) is accomplished by adjusting the performance weights on these parameters for different levels of engine degradation. Nonlinear simulations demonstrate that the controller achieves specified performance objectives while being robust to engine deterioration as well as engine-to-engine variations.

Turso, James A.↗
NASA NTRS2007

Short range RF communication for jet engine control

A method transmitting a message over at least one of a plurality of radio frequency (RF) channels of an RF communications network is provided. The method comprises the steps of detecting a presence of jamming pulses in the at least one of the plurality of RF channels. The characteristics of the jamming pulses in the at least one of the plurality of RF channels is determined wherein the determined characteristics define at least interstices between the jamming pulses. The message is transmitted over the at least one of the plurality of RF channels wherein the message is transmitted within the interstices of the jamming pulse determined from the step of determining characteristics of the jamming pulses.

Sexton, Daniel White↗
NASA NTRS2012

Model-Based Control of an Aircraft Engine using an Optimal Tuner Approach

This paper covers the development of a model-based engine control (MBEC) method- ology applied to an aircraft turbofan engine. Here, a linear model extracted from the Commercial Modular Aero-Propulsion System Simulation 40,000 (CMAPSS40k) at a cruise operating point serves as the engine and the on-board model. The on-board model is up- dated using an optimal tuner Kalman Filter (OTKF) estimation routine, which enables the on-board model to self-tune to account for engine performance variations. The focus here is on developing a methodology for MBEC with direct control of estimated parameters of interest such as thrust and stall margins. MBEC provides the ability for a tighter control bound of thrust over the entire life cycle of the engine that is not achievable using traditional control feedback, which uses engine pressure ratio or fan speed. CMAPSS40k is capable of modeling realistic engine performance, allowing for a verification of the MBEC tighter thrust control. In addition, investigations of using the MBEC to provide a surge limit for the controller limit logic are presented that could provide benefits over a simple acceleration schedule that is currently used in engine control architectures.

Connolly, Joseph W.↗
NASA NTRS1973

Control of turbofan lift engines for VTOL aircraft.

This paper presents the results of an analytical study of the dynamics and control of turbofan lift engines, and proposes methods of meeting the response requirements imposed by the VTOL aircraft application. Two types of lift fan engines are discussed: the integral and remote. The integral engine is a conventional two-spool, high bypass ratio turbofan designed for low noise and short length. The remote engine employs a gas generator and a lift fan which are separated by a duct, and which need not be coaxial. For the integral engine, a control system design is presented which satisfies the VTOL response requirements. For the remote engine, two unconventional methods of control involving flow transfer between lift units are discussed.

Sellers, J. F.↗
NASA NTRS1995

Implementation of probabilistic design methodology at Tennessee State University

The fact that Deterministic Design Method no longer satisfies most design needs calls for methods that will cope with the high trend in technology. The advance in computer technology has reduced the rigors that normally accompany many design analysis methods that account for uncertainties in design parameters. Probabilistic Design Methodology (PDM) is beginning to make impact in engineering design. This method is gaining more recognition in industries than in educational institutions. Some of the reasons for the limited use of the PDM at the moment are that many are unaware of its potentials, and most of the software developed for PDM are very recent. The central goal of the PDM project at Tennessee State University is to introduce engineering students to this method. The students participating in the project learn about PDM and the computer codes that are available to the design engineer. The software being used for this project is NESSUS (Numerical Evaluation of Stochastic Structures Under Stress) developed under NASA probabilistic structural analysis program. NESSUS has three different modules which make it a very comprehensive computer code for PDM. Since this method is new to the students, its introduction into the engineering curriculum is to be in stages. These range from the introduction of PDM and its software to the applications. While this program is being developed for its eventual inclusion into the engineering curriculum, some graduate and undergraduate students are already carrying out some projects using this method. As the students are increasing their understanding on PDM, they are at the same time applying it to some common design problems. The areas this method is being applied at the moment include, Design of Gears (spur and worm); Design of Brakes; Design of Heat Exchangers Design of Helical Springs; and Design of Shock Absorbers. Some of the current results of these projects are presented.

Onwubiko, Chinyere↗
NASA NTRS2002

Fast Bound Methods for Large Scale Simulation with Application for Engineering Optimization

In this work, we have focused on fast bound methods for large scale simulation with application for engineering optimization. The emphasis is on the development of techniques that provide both very fast turnaround and a certificate of Fidelity; these attributes ensure that the results are indeed relevant to - and trustworthy within - the engineering context. The bound methodology which underlies this work has many different instantiations: finite element approximation; iterative solution techniques; and reduced-basis (parameter) approximation. In this grant we have, in fact, treated all three, but most of our effort has been concentrated on the first and third. We describe these below briefly - but with a pointer to an Appendix which describes, in some detail, the current "state of the art."

Patera, Anthony T.↗
NASA NTRS1977

A study of the optimization method used in the NAVY/NASA gas turbine engine computer code

Sources of numerical noise affecting the convergence properties of the Powell's Principal Axis Method of Optimization in the NAVY/NASA gas turbine engine computer code were investigated. The principal noise source discovered resulted from loose input tolerances used in terminating iterations performed in subroutine CALCFX to satisfy specified control functions. A minor source of noise was found to be introduced by an insufficient number of digits in stored coefficients used by subroutine THERM in polynomial expressions of thermodynamic properties. Tabular results of several computer runs are presented to show the effects on program performance of selective corrective actions taken to reduce noise.

Horsewood, J. L.↗
NASA NTRS1987

Three-dimensional inelastic analysis for hot section components, BEST 3D code

The goal is the development of an alternative stress analysis tool, distinct from the finite element method, applicable to the engineering analysis of gas turbine engine structures. The boundary element method was selected for this development effort on the basis of its already demonstrated applicability to a variety of geometries and problem types characteristic of gas turbine engine components. Major features of the BEST3D computer program are described, and some of the significant developments carried out as part of the Inelastic Methods Contract are outlined.

Wilson, Raymond B.↗
NASA NTRS2005

Innovative Adaptive Control Method Demonstrated for Active Suppression of Instabilities in Engine Combustors

This year, an improved adaptive-feedback control method was demonstrated that suppresses thermoacoustic instabilities in a liquid-fueled combustor of a type used in aircraft engines. Extensive research has been done to develop lean-burning (low fuel-to-air ratio) combustors that can reduce emissions throughout the mission cycle to reduce the environmental impact of aerospace propulsion systems. However, these lean-burning combustors are susceptible to thermoacoustic instabilities (high-frequency pressure waves), which can fatigue combustor components and even downstream turbine blades. This can significantly decrease the safe operating life of the combustor and turbine. Thus, suppressing the thermoacoustic combustor instabilities is an enabling technology for meeting the low-emission goals of the NASA Ultra-Efficient Engine Technology (UEET) Project.

Kopasakis, George↗
DOE OSTI2021

Shareable FPGA compute engine

Systems, apparatuses, and methods for sharing an field programmable gate array compute engine are disclosed. A system includes one or more processors and one or more FPGAs. The system receives a request, generated by a first user process, to allocate a portion of processing resources on a first FPGA. The system maps the portion of processing resources of the first FPGA into an address space of the first user process. The system prevents other user processes from accessing the portion of processing resources of the first FPGA. Later, the system detects a release of the portion of the processing resources on the first FPGA by the first user process. Then, the system receives a second request to allocate the first FPGA from a second user process. In response to the second request, the system maps the first FPGA into an address space of the second user process.

Kegel, Andrew G.↗
DOE OSTI2020

Cylinder bore having variable coating

Engine blocks and methods of forming the same are disclosed. The engine block may comprise a body including at least one cylindrical engine bore wall having a longitudinal axis and including a coating extending along the longitudinal axis and having a coating thickness. The coating may have a middle region and first and second end regions, and a plurality of pores may be dispersed within the coating thickness. The middle region may have a different average porosity than one or both of the end regions. The method may include spraying a first porosity coating in a middle longitudinal region of the bore and spraying a second porosity coating in one or more end regions of the bore. The first porosity may be greater than the second porosity and the first and second porosities may be formed during the spraying steps. The pores may act as wells for lubricant.

36 MATERIALS SCIENCE↗
NASA NTRS1985

Nastran's Application in Agricultural Engineering

Finite element analysis has been recognized as a valuable solution method by agricultural engineers. NASTRAN has been obtained by the Agricultural Engineering Department at the University of Georgia. The NASTRAN Thermal Analyzer has been used in the teaching program for an undergraduate course in heat transfer and will be used for a new graduate course in finite element analysis. The NASTRAN Thermal Analyzer has also been applied to several research problems in the Agricultural Engineering Department.

Vanwicklen, G. L.↗
NASA NTRS2017

Current EBC Development and Testing at NASA

SiC SiC Ceramic Matrix Composites (CMCs) are a game changer for advanced power generation equipment because of their high temperature capability, oxidation resistance, and light weight that translate to significant reduction in fuel consumption and emission. Limitations of SiC SiC CMCs include surface recession and component cracking and associated chemical and physical degradation in the CMC. The solution pursued to mitigate surface recession of SiC SiC CMCs is the incorporation of coating systems that provide surface protection, which has become known as an Environmental Barrier Coating (EBC). The development of EBCs for the protection of SiC SiC CMCs was a continuation of coating development work for corrosion protection of silicon-based monolithics. The first and second generation EBCs developed in mid 1990s-early 2000s laid the foundation for current EBCs. Environmental degradation that limits EBC life includes surface recession by steam, oxidation in steam environments, and CMAS-EBC reactions. Many engine tests have been conducted since late 1990s and a first CMC component entered into service in 2016 in a commercial engine. The introduction of CMCs represents significant challenges as failure of the EBC means rapid reduction in component life. A reliable lifing method and engine-relevant testing methods to validate life need to be developed. This paper will current activities on EBC development and testing at NASA.

CMC↗
NASA NTRS2010

The ICARE Method

The ICARE method is a flexible, widely applicable method for systems engineers to solve problems and resolve issues in a complete and comprehensive manner. The method can be tailored by diverse users for direct application to their function (e.g. system integrators, design engineers, technical discipline leads, analysts, etc.). The clever acronym, ICARE, instills the attitude of accountability, safety, technical rigor and engagement in the problem resolution: Identify, Communicate, Assess, Report, Execute (ICARE). This method was developed through observation of Space Shuttle Propulsion Systems Engineering and Integration (PSE&I) office personnel approach in an attempt to succinctly describe the actions of an effective systems engineer. Additionally it evolved from an effort to make a broadly-defined checklist for a PSE&I worker to perform their responsibilities in an iterative and recursive manner. The National Aeronautics and Space Administration (NASA) Systems Engineering Handbook states, engineering of NASA systems requires a systematic and disciplined set of processes that are applied recursively and iteratively for the design, development, operation, maintenance, and closeout of systems throughout the life cycle of the programs and projects. ICARE is a method that can be applied within the boundaries and requirements of NASA s systems engineering set of processes to provide an elevated sense of duty and responsibility to crew and vehicle safety. The importance of a disciplined set of processes and a safety-conscious mindset increases with the complexity of the system. Moreover, the larger the system and the larger the workforce, the more important it is to encourage the usage of the ICARE method as widely as possible. According to the NASA Systems Engineering Handbook, elements of a system can include people, hardware, software, facilities, policies and documents; all things required to produce system-level results, qualities, properties, characteristics, functions, behavior and performance. The ICARE method can be used to improve all elements of a system and, consequently, the system-level functional, physical and operational performance. Even though ICARE was specifically designed for a systems engineer, any person whose job is to examine another person, product, or process can use the ICARE method to improve effectiveness, implementation, usefulness, value, capability, efficiency, integration, design, and/or marketability. This paper provides the details of the ICARE method, emphasizing the method s application to systems engineering. In addition, a sample of other, non-systems engineering applications are briefly discussed to demonstrate how ICARE can be tailored to a variety of diverse jobs (from project management to parenting).

Henke, Luke↗
NASA NTRS2005

Tissue Engineering Using Transfected Growth-Factor Genes

A method of growing bioengineered tissues includes, as a major component, the use of mammalian cells that have been transfected with genes for secretion of regulator and growth-factor substances. In a typical application, one either seeds the cells onto an artificial matrix made of a synthetic or natural biocompatible material, or else one cultures the cells until they secrete a desired amount of an extracellular matrix. If such a bioengineered tissue construct is to be used for surgical replacement of injured tissue, then the cells should preferably be the patient s own cells or, if not, at least cells matched to the patient s cells according to a human-leucocyteantigen (HLA) test. The bioengineered tissue construct is typically implanted in the patient's injured natural tissue, wherein the growth-factor genes enhance metabolic functions that promote the in vitro development of functional tissue constructs and their integration with native tissues. If the matrix is biodegradable, then one of the results of metabolism could be absorption of the matrix and replacement of the matrix with tissue formed at least partly by the transfected cells. The method was developed for articular chondrocytes but can (at least in principle) be extended to a variety of cell types and biocompatible matrix materials, including ones that have been exploited in prior tissue-engineering methods. Examples of cell types include chondrocytes, hepatocytes, islet cells, nerve cells, muscle cells, other organ cells, bone- and cartilage-forming cells, epithelial and endothelial cells, connective- tissue stem cells, mesodermal stem cells, and cells of the liver and the pancreas. Cells can be obtained from cell-line cultures, biopsies, and tissue banks. Genes, molecules, or nucleic acids that secrete factors that influence the growth of cells, the production of extracellular matrix material, and other cell functions can be inserted in cells by any of a variety of standard transfection techniques.

Madry, Henning↗