Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engine emission”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Assessing and controlling the effect of aircraft on the environment: Pollution

The air pollution created by aircraft engines around airports and the global atmospheric problem of supersonic aircraft operating in the stratosphere are discussed. Methods for assessing the air pollution impact are proposed. The use of atmospheric models to determine the air pollution extent is described. Methods for controlling the emissions of aircraft engines are examined. Diagrams of the atmospheric composition resulting from exhaust gas emissions are developed.

Poppoff, I. G.↗

Water Misting and Injection of Commercial Aircraft Engines to Reduce Airport NOx

This report provides the first high level look at system design, airplane performance, maintenance, and cost implications of using water misting and water injection technology in aircraft engines for takeoff and climb-out NOx emissions reduction. With an engine compressor inlet water misting rate of 2.2 percent water-to-air ratio, a 47 percent NOx reduction was calculated. Combustor water injection could achieve greater reductions of about 85 percent, but with some performance penalties. For the water misting system on days above 59 F, a fuel efficiency benefit of about 3.5 percent would be experienced. Reductions of up to 436 F in turbine inlet temperature were also estimated, which could lead to increased hot section life. A 0.61 db noise reduction will occur. A nominal airplane weight penalty of less than 360 lb (no water) was estimated for a 305 passenger airplane. The airplane system cost is initially estimated at $40.92 per takeoff giving an attractive NOx emissions reduction cost/benefit ratio of about $1,663/ton.

Daggett, David L.↗

Wide range operation of advanced low NOx combustors for supersonic high-altitude aircraft gas turbines

An initial rig program tested the Jet Induced Circulation (JIC) and Vortex Air Blast (VAB) systems in small can combustor configurations for NOx emissions at a simulated high altitude, supersonic cruise condition. The VAB combustor demonstrated the capability of meeting the NOx goal of 1.0 g NO2/kg fuel at the cruise condition. In addition, the program served to demonstrate the limited low-emissions range available from the lean, premixed combustor. A follow-on effort was concerned with the problem of operating these lean, premixed combustors with acceptable emissions at simulated engine idle conditions. Various techniques have been demonstrated that allow satisfactory operation on both the JIC and VAB combustors at idle with CO emissions below 20 g/kg fuel. The VAB combustor was limited by flashback/autoignition phenomena at the cruise conditions to a pressure of 8 atmospheres. The JIC combustor was operated up to the full design cruise pressure of 14 atmospheres without encountering an autoignition limitation although the NOx levels, in the 2-3 g NO2/kg fuel range, exceeded the program goal.

Roberts, P. B.↗

An Investigation into the Effects of Swirl on the Performance and Emissions of an Opposed-Piston Two-Stroke Engine using Large Eddy Simulations

Opposed-piston two-stroke (OP-2S) engines have the potential to achieve higher thermal efficiency than a conventional four-stroke diesel engine. However, the uniflow scavenging process is difficult to control over a wider range of speed and loads due to its sensitivity to pressure dynamics, port timings, and port design. Specifically, the angle of the intake ports can be used to generate swirl which has implications for open and closed cycle effects. This study proposes an analysis of the effects of port angle on the in-cylinder flow distribution and combustion performance of an OP-2S using computational fluid dynamics engine. Large Eddy Simulation (LES) was used to model turbulence given its ability to predict in-cylinder mixing and cyclic variability. A three-cylinder model was validated to experimental data collected by Achates Power and the grid was verified using an LES quality approach from the literature. The model was used to simulate port angles from 12 to 29 degrees at constant pressure and temperature boundary conditions. Results indicated that the higher bulk swirl ratio generated by larger port angles tends to trap more internal residuals. This effect on the scavenging performance, combined with the larger trapped swirl ratio, also has a significant impact on the combustion performance in a two-stroke engine. It was concluded that there exists a tradeoff of efficiency and emissions that must be considered when increasing the port angle in a uniflow two-stroke engine. 1. Introduction Two-stroke engines were developed in the 1800s and are commonly used in practice today for lightweight power applications such as motorcycles or handheld power tools, as well as large-bore low speed engines for stationary power and marine applications. Two-stroke engines provide the distinct advantage of higher torque/power output but present challenges due to its coupled intake and exhaust process. Four-stroke engines have the benefit of using two full piston strokes to induct intake charge and to expel exhaust gases. Controlling the trapped charge composition in a twostroke engine via a scavenging process is crucial for reliable and efficient engine operation.

33 ADVANCED PROPULSION SYSTEMS↗

Gas turbine engine with recirculating bleed

Carbon monoxide and unburned hydrocarbon emissions in a gas turbine engine are reduced by bleeding hot air from the engine cycle and introducing it back into the engine upstream of the bleed location and upstream of the combustor inlet. As this hot inlet air is recycled, the combustor inlet temperature rises rapidly at a constant engine thrust level. In most combustors, this will reduce carbon monoxide and unburned hydrocarbon emissions significantly. The preferred locations for hot air extraction are at the compressor discharge or from within the turbine, whereas the preferred reentry location is at the compressor inlet.

Adamson, A. P.↗

Investigation of Ammonia Carrier Materials for Next Generation Ammonia Dosing System - CRADA 334 (Abstract)

Lean-burn gasoline and diesel engines can offer substantially higher fuel efficiency, good driving performance, and reduced carbon dioxide emission compared to stoichiometric gasoline engines. Various catalyst technologies have been developed to remove the pollutants from these engines. For example, a three-way catalyst (TWC) is used to remove hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NOx) from gasoline engines during the stoichiometric conditions. During the lean-burn conditions, a TWC or a diesel oxidation catalyst (DOC) is used to control HC and CO emissions. NOx is removed by either lean NOx trap catalyst (LNT) that can store NOx under lean conditions and reduce NOx under rich conditions, or selective catalytic reduction catalyst (SCR) that can selectively remove NOx with a reducing agent. Among the NOx reduction catalyst technologies, SCR offers a number of advantages, including excellent NOx reduction efficiency over a wide range of temperatures and overall lower system cost. In fact, the SCR technology using ammonia (NH3) as reductant has been proven effective and used commercially for the removal of NOx emissions from stationary sources since the 1970s. Currently, SCR is being used to meet the NOx emission standards for diesel engines in Europe and North America, and also being considered for meeting the future NOx emission standards for lean-burn gasoline engines. Because of the challenges associated with storage, handling and transportation of ammonia on a vehicle, aqueous urea solution (e.g., Diesel Exhaust Fluid, AdBlue) has been developed as ammonia storage compound for mobile applications. When the aqueous urea solution is sprayed into exhaust gas stream, urea is decomposed to release ammonia, which then reduces NOx over the downstream SCR catalyst. Although aqueous urea solution technology has enabled automakers and engine manufacturers to meet the current NOx emission standards, this process of releasing ammonia requires a hot exhaust gas and sufficient mixing, creating challenges for low temperature NOx emission control and aftertreatment system packaging. For these reasons, alternative technologies have been developed as ammonia sources (e.g., solid urea, ammonium carbamate, metal ammine chloride) during the past few years. These technologies promise more convenient handling and distribution of ammonia sources, and help maximize the low-temperature performance of SCR catalysts and reduce the overall system volume and weight. However, none of these alternative technologies can be successfully implemented without the industry consensus. Therefore, the USCAR SCR work group, which is comprised of representatives from GM, Ford, and Chrysler, has decided to investigate the potential alternative ammonia carriers, define common standard vehicle interfaces, and address personal and environmental safety concerns with part suppliers and chemical companies. Under this CRADA Project, USCAR and Battelle will investigate alternative ammonia carrier materials that are currently under development. Based on the data and information derived under the CRADA project, the USCAR SCR work group plans to build the consensus and make recommendations for the industry.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Investigation of Ammonia Carrier Materials for Next Generation Ammonia Dosing System - CRADA 334 (Abstract)

Lean-burn gasoline and diesel engines can offer substantially higher fuel efficiency, good driving performance, and reduced carbon dioxide emission compared to stoichiometric gasoline engines. Various catalyst technologies have been developed to remove the pollutants from these engines. For example, a three-way catalyst (TWC) is used to remove hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NOx) from gasoline engines during the stoichiometric conditions. During the lean-burn conditions, a TWC or a diesel oxidation catalyst (DOC) is used to control HC and CO emissions. NOx is removed by either lean NOx trap catalyst (LNT) that can store NOx under lean conditions and reduce NOx under rich conditions, or selective catalytic reduction catalyst (SCR) that can selectively remove NOx with a reducing agent. Among the NOx reduction catalyst technologies, SCR offers a number of advantages, including excellent NOx reduction efficiency over a wide range of temperatures and overall lower system cost. In fact, the SCR technology using ammonia (NH3) as reductant has been proven effective and used commercially for the removal of NOx emissions from stationary sources since the 1970s. Currently, SCR is being used to meet the NOx emission standards for diesel engines in Europe and North America, and also being considered for meeting the future NOx emission standards for lean-burn gasoline engines. Because of the challenges associated with storage, handling and transportation of ammonia on a vehicle, aqueous urea solution (e.g., Diesel Exhaust Fluid, AdBlue) has been developed as ammonia storage compound for mobile applications. When the aqueous urea solution is sprayed into exhaust gas stream, urea is decomposed to release ammonia, which then reduces NOx over the downstream SCR catalyst. Although aqueous urea solution technology has enabled automakers and engine manufacturers to meet the current NOx emission standards, this process of releasing ammonia requires a hot exhaust gas and sufficient mixing, creating challenges for low temperature NOx emission control and aftertreatment system packaging. For these reasons, alternative technologies have been developed as ammonia sources (e.g., solid urea, ammonium carbamate, metal ammine chloride) during the past few years. These technologies promise more convenient handling and distribution of ammonia sources, and help maximize the low-temperature performance of SCR catalysts and reduce the overall system volume and weight. However, none of these alternative technologies can be successfully implemented without the industry consensus. Therefore, the USCAR SCR work group, which is comprised of representatives from GM, Ford, and Chrysler, has decided to investigate the potential alternative ammonia carriers, define common standard vehicle interfaces, and address personal and environmental safety concerns with part suppliers and chemical companies. Under this CRADA Project, USCAR and Battelle will investigate alternative ammonia carrier materials that are currently under development. Based on the data and information derived under the CRADA project, the USCAR SCR work group plans to build the consensus and make recommendations for the industry.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

FY2011 Annual Progress Report: Advanced Combustion Engine Research and Development (Book)

Annual Progress Report for the Advanced Combustion Engine Research and Development (R&D) subprogram supporting the mission of the Vehicle Technologies Program by removing the critical technical barriers to commercialization of advanced internal combustion engines (ICEs) for passenger and commercial vehicles that meet future federal emissions regulations.

combustion engine, ICE, emission control↗

Effects of fuel viscosity on the primary breakup dynamics of a high-speed liquid jet with comparison to X-ray radiography

One of the major concerns in combustion engines is the sensitivity of engine performance to fuel prop- erties. Recent works have shown that even slight differences in fuel properties can cause significant changes in performance and emission of an engine. In order to design the combustion engines with multi-fuel flexi- bilities, the precise assessment of fuel sensitivity on liquid jet atomization process is a prerequisite since the resulting fuel/air mixture is critical to the subsequent combustion process. The present study is focusing on the effect of physical fuel properties, mostly viscosity difference, on the breakup process of the liquid jet injected into still air. Two different jet fuels, CAT-A2 and CAT-C3, are considered here as surrogates for a fossil-based fuel and a bio-derived high-viscosity alternative fuel. The simulations are performed using the volume-of-fluid (VoF) interface tracking method coupled to Lagrangian particle method in order to capture the breakup instabilities of jets and the resulting droplets. The investigations take the actual geometry of the injector into account to resolve the unsteady flow phenomena inside the nozzle that impact the turbu- lence transition and atomization. The simulation results are compared to the experimental measurement using X-ray radiography. Both simulation and X-ray measurements consistently describe the effects of different fuels on the fundamental properties of atomization including the breakup length, transverse liquid volume fraction and the droplet sauter-mean-diameter. The application of a Detailed Numerical Simulation approach complemented by unique X-ray diagnostics is novel and providing new understanding and research directions in engine spray dynamics

Breakup instability↗

Performance, Efficiency and Emissions Assessment of Natural Gas Direct Injection compared to Gasoline and Natural Gas Port-Fuel Injection in an Automotive Engine

Interest in natural gas as a fuel for light-duty transportation has increased due to its domestic availability and lower cost relative to gasoline. Natural gas, comprised mainly of methane, has a higher knock resistance than gasoline making it advantageous for high load operation. However, the lower flame speeds of natural gas can cause ignitability issues at part-load operation leading to an increase in the initial flame development process. While port-fuel injection of natural gas can lead to a loss in power density due to the displacement of intake air, injecting natural gas directly into the cylinder can reduce such losses. A study was designed and performed to evaluate the potential of natural gas for use as a light-duty fuel. Steady-state baseline tests were performed on a single-cylinder research engine equipped for port-fuel injection of gasoline and natural gas, as well as centrally mounted direct injection of natural gas. Experimental results suggest that similar efficiencies can be achieved in part-load operation for both gasoline and natural gas. While the effects of injection timing are generally minimal for port-fuel injection, varying the injection timing for direct injection, especially after intake valve closure, can speed up the early flame development process by nearly 18°CA. Results at full-load suggest that operation with natural gas regardless of fuel system allows for an efficiency increase. While port-fuel injection of natural gas leads to a power density loss, direct injection of natural gas allows for up to a 10% improvement in full-load power density over liquid and gaseous port-fuel injection for a naturally aspirated engine. In addition to increasing full-load efficiencies, natural gas operation allows for up to a 30% reduction in engine out carbon dioxide emissions at full-load.

Sevik, James M↗

Performance and emissions characteristics of aqueous alcohol fumes in a DI diesel engine

A single cylinder DI Diesel engine was fumigated with ethanol and methanol in amounts up to 55% of the total fuel energy. The effects of aqueous alcohol fumigation on engine thermal efficiency, combustion intensity and gaseous exhaust emissions were determined. Assessment of changes in the biological activity of raw particulate and its soluble organic fraction were also made using the Salmonella typhimurium test. Alcohol fumigation improved thermal efficiency slightly at moderate and heavy loads, but increased ignition delay at all operating conditions. Carbon monoxide and unburned hydrocarbon emission generally increased with alcohol fumigation and showed no dependence on alcohol type or quality. Oxide of nitrogen emission showed a strong dependence on alcohol quality; relative emission levels decreased with increasing water content of the fumigant. Particulate mass loading rates were lower for ethanol fueled conditions. However, the biological activity of both the raw particulate and its soluble organic fraction was enhanced by ethanol fumigation at most operating conditions.

Heisey, J. B.↗

Advanced Thermal HPT Clearance Control

OBJECTIVE: Develop a fast acting HPT Active Clearance Control System to improve engine efficiency and reduce emissions CHALLENGE: Reduction of HPT blade clearance throughout engine operation System complexity, reliability and cost must remain comparable or surpass today s engines Reduced clearance may increase possibility of rubs

WojciechVoytek, Sak↗

Design Concepts for Cooled Ceramic Matrix Composite Turbine Vanes

This project demonstrated that higher temperature capabilities of ceramic matrix composites (CMCs) can be used to reduce emissions and improve fuel consumption in gas turbine engines. The work involved closely coupling aerothermal and structural analyses for the first-stage vane of a high-pressure turbine (HPT). These vanes are actively cooled, typically using film cooling. Ceramic materials have structural and thermal properties different from conventional metals used for the first-stage HPT vane. This project identified vane configurations that satisfy CMC structural strength and life constraints while maintaining vane aerodynamic efficiency and reducing vane cooling to improve engine performance and reduce emissions. The project examined modifications to vane internal configurations to achieve the desired objectives. Thermal and pressure stresses are equally important, and both were analyzed using an ANSYS® structural analysis. Three-dimensional fluid and heat transfer analyses were used to determine vane aerodynamic performance and heat load distributions.

Boyle, Robert↗

Hafnia-Based Materials Developed for Advanced Thermal/Environmental Barrier Coating Applications

Thermal and environmental barrier coatings (T/EBCs) will play a crucial role in advanced gas turbine engine systems because of their ability to significantly increase engine operating temperatures and reduce cooling requirements, and thus help achieve engine goals of low emissions and high efficiency. Under the NASA Ultra-Efficient Engine Technology (UEET) Project, advanced T/EBCs are being developed for low-emission SiC/SiC ceramic matrix composite (CMC) combustor applications by extending the CMC liner and vane temperature capability to 1650 C (3000 F) in oxidizing and water-vaporcontaining combustion environments. The coating system is required to have increased phase stability, lower lattice and radiation thermal conductivity, and improved sintering and thermal stress resistance under high-heat-flux and thermal-cycling engine conditions. Advanced heat-flux testing approaches (refs. 1 to 4) have been established at the NASA Glenn Research Center for 1650 C coating developments. The simulated combustion water-vapor environment is also being incorporated into the heat-flux test capabilities (ref. 3).

Zhu, Dongming↗

Simultaneous Control of Unburned NH 3 and NO x Emissions From High Load Dual-Fuel Ammonia Operation on a High-Speed Diesel Engine Using a Cu-SCR System

Dual-fuel ammonia strategies are being investigated as a promising way to utilize NH 3 as an alternative fuel for internal combustion engines in the maritime sector. One of the remaining barriers to implementing dual-fuel NH 3 combustion strategies is understanding ways to minimize unburned NH 3 and nitrogen oxide (NO x ) emissions from these engines, both of which are elevated relative to a conventional diesel baseline. Selective catalytic reduction (SCR) systems are widely used for lean NO x emission controls for engines across transportation and stationary energy applications. SCR systems use a reducing agent, such as NH 3 , to react with NO x in the exhaust, converting it into nitrogen and water. Typically, NH 3 is injected into the exhaust as a urea solution. In dual-fuel NH 3 engines, where unburned NH 3 is present in the exhaust, an SCR system could be used to mitigate both NH 3 and NO x emissions. The presented work evaluates a commercial copper-zeolite SCR and ammonia slip catalyst system, designed for on-road diesel engine applications, for controlling unburned NH 3 and NO x emissions from a dual-fuel NH 3 combustion engine. The aftertreatment system was installed downstream of a single-cylinder four-stroke diesel engine that has been modified for dual-fuel ammonia use. Furthermore, the emissions were characterized by using a Fourier transform infrared spectrometer for both late- and early-injection diesel pilot strategies over three air–fuel equivalence ratios spanning from 1.6 to 1.0 at 1200 rpm and 12.6 bar IMEP g condition (with greater than 95% ammonia energy fraction). Initial findings indicate that the SCR achieves more than 99% NO x conversion with less than 50 ppm NH 3 slip at air–fuel equivalence ratios greater than 1.4 at the operating conditions investigated. However, these benefits are accompanied by additional N 2 O emissions that are formed over the Cu-SCR.

Catalysts↗

Avco Lycoming QCGAT program design cycle, demonstrated performance and emissions

A high bypass ratio, twin spool turbofan engine of modular design which incorporates a front fan module driven by a modified LTS101 core engine was tested. The engine is housed in a nacelle incorporating full length fan ducting with sound treatment in both the inlet and fan discharge flow paths. Design goals of components and results of component tests are presented together with full engine test results. The rationale behind the combustor design selected for the engine is presented as well as the emissions test results. Total system (engine and nacelle) test results are included.

Fogel, P.↗

Design of AlGaN-Zn(Si,Ge)N2 quantum wells for high-efficiency ultraviolet light emitters

The effect of inserting a nm-scale layer of Zn(Si,Ge)N2 into an AlGaN quantum well structure designed for light emission in the wavelength range from 255 to 305 nm is investigated here. The enhanced confinement of the hole within the quantum well results in an enhancement of the overlap of the hole and electron wave functions, resulting in an enhancement of the radiative recombination rate. In this theoretical calculation, for emission at a 270 nm wavelength, the enhancement in the wavefunction overlap can reach a factor of 7 when compared to an AlGaN quantum well device specifically engineered for optimal emission at the identical wavelength. Increases of almost an order of magnitude in both the peak spontaneous emission intensity and the radiative recombination rate are predicted. The peak emission wavelength can be tuned from 255 to 305 nm by adjusting the width and/or the composition of the inserted layer. The proposed structures provide a route to higher efficiency ultraviolet practical light emitting diodes and lasers.

Physics↗

A New Method for Accurate Treatment of Flow Equations in Cylindrical Coordinates Using Series Expansions

The motivation of this work is the ongoing effort at the Center for Turbulence Research (CTR) to use large eddy simulation (LES) techniques to calculate the noise radiated by jet engines. The focus on engine exhaust noise reduction is motivated by the fact that a significant reduction has been achieved over the last decade on the other main sources of acoustic emissions of jet engines, such as the fan and turbomachinery noise, which gives increased priority to jet noise. To be able to propose methods to reduce the jet noise based on results of numerical simulations, one first has to be able to accurately predict the spatio-temporal distribution of the noise sources in the jet. Though a great deal of understanding of the fundamental turbulence mechanisms in high-speed jets was obtained from direct numerical simulations (DNS) at low Reynolds numbers, LES seems to be the only realistic available tool to obtain the necessary near-field information that is required to estimate the acoustic radiation of the turbulent compressible engine exhaust jets. The quality of jet-noise predictions is determined by the accuracy of the numerical method that has to capture the wide range of pressure fluctuations associated with the turbulence in the jet and with the resulting radiated noise, and by the boundary condition treatment and the quality of the mesh. Higher Reynolds numbers and coarser grids put in turn a higher burden on the robustness and accuracy of the numerical method used in this kind of jet LES simulations. As these calculations are often done in cylindrical coordinates, one of the most important requirements for the numerical method is to provide a flow solution that is not contaminated by numerical artifacts. The coordinate singularity is known to be a source of such artifacts. In the present work we use 6th order Pade schemes in the non-periodic directions to discretize the full compressible flow equations. It turns out that the quality of jet-noise predictions using these schemes is especially sensitive to the type of equation treatment at the singularity axis. The objective of this work is to develop a generally applicable numerical method for treating the singularities present at the polar axis, which is particularly suitable for highly accurate finite-differences schemes (e.g., Pade schemes) on non-staggered grids. The main idea is to reinterpret the regularity conditions developed in the context of pseudo-spectral methods. A set of exact equations at the singularity axis is derived using the appropriate series expansions for the variables in the original set of equations. The present treatment of the equations preserves the same level of accuracy as for the interior scheme. We also want to point out the wider utility of the method, proposed here in the context of compressible flow equations, as its extension for incompressible flows or for any other set of equations that are solved on a non-staggered mesh in cylindrical coordinates with finite-differences schemes of various level of accuracy is straightforward. The robustness and accuracy of the proposed technique is assessed by comparing results from simulations of laminar forced-jets and turbulent compressible jets using LES with similar calculations in which the equations are solved in Cartesian coordinates at the polar axis, or in which the singularity is removed by employing a staggered mesh in the radial direction without a mesh point at r = 0.

Constantinescu, G.S.↗