Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELASTIC MODULUS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Cyclic nanoindentation studies on CrN thin films prepared by RF sputtering on Zr-based metallic glass

Cyclic nanoindentation tests were carried out to study the influence of the chromium nitride thin films on the mechanical properties of Zr-based metallic glass. Chromium nitride thin coatings have been deposited on Zr{sub 50}Cu{sub 40}Al{sub 10} metallic glass substrate by RF sputtering. The deposition process was done at room temperature under nitrogen reactive gas using a metallic chromium target. The CrN films have a thickness of 300 nm. Several cyclic nanoindentation measurements were conducted on CrN films and Zr{sub 50}Cu{sub 40}Al{sub 10} metallic glass substrate samples at various loading rate values. We have found that the coated metallic glass sample shows high mechanical properties such as hardness and reduced elastic modulus. Cyclic nanoindentation results show a hardening behaviour for these CrN coatings. Moreover, the CrN coated on Zr-based metallic glass was found to have a high value of resistance to crack propagation, as being analysed through the SEM pictures of the residual Vickers indentation impressions.

36 MATERIALS SCIENCE↗

Manipulating Stress in Cu/low-k Dielectric Nanocomposites

The interaction of x-rays with organic dielectric materials, which alters their mechanical properties, affects values of stress generated within encapsulated Cu structures. In particular, the evolution of stress within submicron Cu interconnect structures encapsulated by an organosilicate glass can be investigated in situ using synchrotron-based x-ray diffraction. The overall geometry of the composite, along with the amount of irradiation, dictates the change in stress of the Cu features. A quantitative comparison of these findings to mechanical modeling results reveals two modes of modification within the dielectric film: a densification that changes the effective eigenstrain followed by an increase in elastic modulus.

36 MATERIALS SCIENCE↗

Studies of pure and nitrogen-incorporated hydrogenated amorphous carbon thin films and their possible application for amorphous silicon solar cells

Hydrogenated amorphous carbon (a-C:H) and nitrogen-incorporated a-C:H (a-C:N:H) thin films were deposited using radio frequency-plasma-enhanced chemical vapor deposition technique and studied for their electrical, optical, and nano-mechanical properties. Introduction of nitrogen and increase of self bias enhanced the conductivity of a-C:H and a-C:N:H films, whereas current-voltage measurement reveals heterojunction formation due to their rectifying behavior. The bandgap of these films was changed over wide range from 1.9 eV to 3.45 eV by varying self bias and the nitrogen incorporation. Further, activation energy was correlated with the electronic structure of a-C:H and a-C:N:H films, and conductivity was discussed as a function of bandgap. Moreover, a-C:N:H films exhibited high hardness and elastic modulus, with maximum values as 42 GPa and 430 GPa, respectively, at -100 V. Observed fascinating electrical, optical, and nano-mechanical properties made it a material of great utility in the development of optoelectronic devices, such as solar cells. In addition, we also performed simulation study for an a-Si:H solar cell, considering a-C:H and C:N:H as window layers, and compared their performance with the a-Si:H solar cell having a-SiC:H as window layer. We also proposed several structures for the development of a near full-spectrum solar cell. Moreover, due to high hardness, a-C:N:H films can be used as a protective and encapsulate layer on solar cells, especially in n-i-p configuration on metal substrate. Nevertheless, a-C:H and a-C:N:H as a window layer can avoid the use of additional hard and protective coating and, hence, minimize the cost of the product.

36 MATERIALS SCIENCE↗

In situ tensile and creep testing of lithiated silicon nanowires

We present experimental results for uniaxial tensile and creep testing of fully lithiated silicon nanowires. A reduction in the elastic modulus is observed when silicon nanowires are alloyed with lithium and plastic deformation becomes possible when the wires are saturated with lithium. Creep testing was performed at fixed force levels above and below the tensile strength of the material. A linear dependence of the strain-rate on the applied stress was evident below the yield stress of the alloy, indicating viscous deformation behavior. The observed inverse exponential relationship between wire radius and strain rate below the yield stress indicates that material transport was controlled by diffusion. At stress levels approaching the yield strength of fully lithiated silicon, power-law creep appears to govern the strain-rate dependence on stress. These results have direct implications on the cycling conditions, rate-capabilities, and charge capacity of silicon and should prove useful for the design and construction of future silicon-based electrodes.

36 MATERIALS SCIENCE↗

Low-temperature mechanical properties of glass/epoxy laminates

Selected mechanical properties of glass/epoxy laminate candidates for use in the electrical turn and ground insulation of the ITER Central solenoid (CS) modules were measured. Short-beam shear and flexural tests have been conducted on various E-glass cloth weaves/epoxy laminates at 295 and 77 K. Types of glass weave include 1581, 7500, 7781, and 38050, which represent both satin and plain weaves. The epoxy, planned for use for vacuum-pressure impregnation of the CS module, consists of an anhydride-cured bisphenol F resin system. Inter-laminar shear strength, flexural elastic modulus, and flexural strength have been measured. The data indicate that these properties are dependent on the volume percent of glass. Short-beam shear strength was measured as a function of the span-to-thickness ratio for all laminates at 77 K. Comprehensive fractography was conducted to obtain the failure mode of each short-beam shear test sample.

36 MATERIALS SCIENCE↗

Serrated flow behaviors of a Zr-based bulk metallic glass by nanoindentation

Instrumented nanoindentation tests were used to investigate the mechanical properties of Zr{sub 52.5}Cu{sub 17.9}Ni{sub 14.6}Al{sub 10}Ti{sub 5} bulk metallic glass. The corresponding loading strain rates were ranged from 0.002 s{sup −1}, 0.02 s{sup −1} to 0.2 s{sup −1}. Plastic flow of this material exhibited remarkable serrations at low strain rates and increasingly became weakening until disappearance with increasing indentation strain rate, implying strong rate sensitivity. A significant pile-up around the indents was observed through atomic force microscopy, which suggested a highly localized plastic deformation. Mechanism governing the deformation was tentatively discussed in terms of the increasing process of free volume with a negligible temperature rise under low strain rate, which well explained the declining trend of elastic modulus and hardness with an increase of indentation depth.

36 MATERIALS SCIENCE↗

Hypercrosslinked polystyrene networks: An atomistic molecular dynamics simulation combined with a mapping/reverse mapping procedure

An algorithm involving classical molecular dynamics simulations with mapping and reverse mapping procedure is here suggested to simulate the crosslinking of the polystyrene dissolved in dichloroethane by monochlorodimethyl ether. The algorithm comprises consecutive stages: molecular dynamics atomistic simulation of a polystyrene solution, the mapping of atomistic structure onto coarse-grained model, the crosslink formation, the reverse mapping, and finally relaxation of the structure dissolved in dichloroethane and in dry state. The calculated values of the specific volume and the elastic modulus are in reasonable quantitative correspondence with experimental data.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ab initio studies on phase transition, thermoelastic, superconducting and thermodynamic properties of the compressed cubic phase of AlH{sub 3}

The phase transition, thermoelastic, lattice dynamic, and thermodynamic properties of the cubic metallic phase AlH{sub 3} were obtained within the density-function perturbation theory. The calculated elastic modulus and phonon dispersion curves under various pressures at 0 K indicate the cubic phase is both mechanically and dynamically stable above 73 GPa. The superconducting transition temperature T{sub c} was calculated using the Allen-Dynes modification of the McMillan formula based on BCS theory. The calculations show that T{sub c} for the cubic phase AlH{sub 3} is 8.5 K (μ{sup *}=0.1) at the onset of this phase (73 GPa), while decreases to 5.7 K at 80 GPa and almost disappears at 110 GPa, consisting with experimental phenomenon that there was no superconducting transition observed down to 4 K over a wide pressure range 110–164 GPa. It is found that the soft phonon mode for branch 1, namely, the lowest acoustic mode, plays a crucial role in elevating the total EPC parameter λ of cubic AlH{sub 3}. And the evolution of T{sub c} with pressure follows the corresponding change of this soft mode, i.e. this mode is responsible for the disappearance of T{sub c} in experiments. Meanwhile, the softening of this lowest acoustic mode originates from the electronic momentum transfer from M to R point. This phenomenon provides an important insight into why drastic changes in the diffraction pattern were observed in the pressure range of 63–73 GPa in Goncharenko's experiments. Specifically, once finite electronic temperature effects are included, we find that dynamical instabilities can be removed in the phonon dispersion for P≥63 GPa, rendering the metastability of this phase in the range of 63–73 GPa, and T{sub c} (15.4 K) becomes remarkably high under the lowest possible pressure (63 GPa) compared with that of under 73 GPa (8.5 K). Our calculations open the possibility that finite temperature may allow cubic AlH{sub 3} to be dynamically stabilized even for pressures below 73 GPa. It is reasonable to deduced that if special techniques, such as rapid decompression, quenching, and annealing, are implemented in experiments, higher T{sub c} can be observed in hydrides or hydrogen-rich compounds under much lower pressure than ever before.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nanowell-patterned TiO{sub 2} microcantilevers for calorimetric chemical sensing

A sensitive calorimetric sensor using a TiO{sub 2} microcantilever with nanowells patterned on one of its sides is described. This single material cantilever is sensitive to temperature change without relying on the metal deposition-based bimetallic effect. The thermomechanical sensitivity originates from the structure dependent variations in both the elastic modulus and thermal expansion coefficient due to the presence of ordered nanowells. These cantilever beams offer an alternate and efficient chemical sensing route for vapor phase analytes using photothermal spectroscopy. Selective and sensitive detection of organophosphorus compounds, as well as their photocatalytic decomposition under ultraviolet light exposure are demonstrated.

36 MATERIALS SCIENCE↗

High quality factor nanocrystalline diamond micromechanical resonators limited by thermoelastic damping

We demonstrate high quality factor thin-film nanocrystalline diamond micromechanical resonators with quality factors limited by thermoelastic damping. Cantilevers, single-anchored and double-anchored double-ended tuning forks, were fabricated from 2.5 μm thick in-situ boron doped nanocrystalline diamond films deposited using hot filament chemical vapor deposition. Thermal conductivity measured by time-domain thermoreflectance resulted in 24 ± 3 W m{sup −1} K{sup −1} for heat transport through the thickness of the diamond film. The resonant frequencies of the fabricated resonators were 46 kHz–8 MHz and showed a maximum measured Q ≈ 86 000 at f{sub n} = 46.849 kHz. The measured Q-factors are shown to be in good agreement with the limit imposed by thermoelastic dissipation calculated using the measured thermal conductivity. The mechanical properties extracted from resonant frequency measurements indicate a Young's elastic modulus of ≈788 GPa, close to that of microcrystalline diamond.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Role of different compatibilizing approaches on the microstructure and mechanical properties of polypropylene/talc composites

Since in a highly filled polymer, a major problem arises from non-uniformity of properties due to the poor dispersion of filler, the application of coupling agents have been directed to overcome this problem and also to enhance the mechanical performance of the composites by improving the adhesion at the interface. In this study, a comparison between two major coupling approaches is conducted: 1) Using PPgMA as a kind of compatibilizer which changes the nature of the matrix, 2) Using titanate coupling agent which takes action at the interface and reacts with hydroxyl groups at the inorganic filler surface, resulting in the formation of monomolecular layer on the inorganic surface to increase compatibility of filler/matrix interface. The comparison is made based on the mechanical properties of the composites by means of elastic modulus, yield stress, impact strength and percentage of strain-to-fracture and evaluation of their effects on both the dispersion and adhesion of talc plates in the matrix through the microscopy. Transmission optical microscopy (TOM) and scanning electron microscopy (SEM) are used to observe the deformation micromechanism and the fracture surface of the composites, respectively.

36 MATERIALS SCIENCE↗

Processing and characterization of multi-cellular monolithic bioceramics for bone regenerative scaffolds

Multicellular monolithic ceramic body is a ceramic material which has many gas or liquid passages partitioned by thin walls throughout the bulk material. There are many currently known advanced industrial applications of multicellular ceramics structures i.e. as supports for various catalysts, electrode support structure for solid oxide fuel cells, refractories, electric/electronic materials, aerospace vehicle re-entry heat shields and biomaterials for dental as well as orthopaedic implants by naming only a few. Multicellular ceramic bodies are usually made of ceramic phases such as mullite, cordierite, aluminum titanate or pure oxides such as silica, zirconia and alumina. What make alumina ceramics is excellent for the above functions are the intrinsic properties of alumina which are hard, wear resistant, excellent dielectric properties, resists strong acid and alkali attacks at elevated temperatures, good thermal conductivities, high strength and stiffness as well as biocompatible. In this work the processing technology leading to truly multicellular monolithic alumina ceramic bodies and their characterization are reported. Ceramic slip with 66 wt.% solid loading was found to be optimum as impregnant to the polyurethane foam template. Mullitic ceramic composite of alumina-sodium alumino disilicate-Leucite-like phases with bulk and true densities of 0.852 and 1.241 g cm{sup −3} respectively, pore linear density of ±35 cm{sup −1}, linear and bulk volume shrinkages of 7-16% and 32 vol.% were obtained. The compressive strength and elastic modulus of the bioceramics are ≈0.5-1.0 and ≈20 MPa respectively.

36 MATERIALS SCIENCE↗

Effect of a hard sublayer on contact interaction and wear behavior of electrodeposited gold-based coatings

The mechanical properties and wear of electroplated Au–Ni coatings deposited on beryllium bronze substrates with Ni or Ni–B intermediate layers were investigated. It was revealed that the sublayer material has no significant effect on the hardness and the elastic modulus of the coatings. At the same time, the harder sublayer favors localization of plastic deformation and, thus, strain hardening of coatings in the course of tribological tests. The Ni–B sublayer was shown to provide significant wear reduction of Au–Ni coatings as compared with the Ni sublayer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects of configurational changes on electrical resistivity during glass-liquid transition of two bulk metal-alloy glasses

Consequences of increase in structural fluctuations on heating Pd{sub 40}Ni{sub 10}Cu{sub 30}P{sub 20} and Zr{sub 46.75}Ti{sub 8.25}Cu{sub 7.5}Ni{sub 10}Be{sub 27.5} through their glass to liquid transition range were investigated by measuring the electrical resistivity, ρ, an electron scattering property. The temperature coefficient of resistivity (TCR = (1/ρ) dρ/dT) of the liquid and glassy states is negative. The plots of their ρ against T in the T{sub g} (glass to liquid transition) range show a gradual change in the slope similar to the change observed generally for the plots of the density, elastic modulus, and refractive index. As fluctuations in the melt structure involve fewer configurations on cooling, ρ increases. In the energy landscape description, the melt's structure explores fewer minima with decrease in T, vibrational frequencies increase, and electron scattering and ρ increase. Plots of (−dρ/dT) against T resemble the plot of the specific heat of other glasses and show a sub-T{sub g} feature and a rapid rise at T near T{sub g}. Analysis shows that the magnitude of negative TCR is dominated by change in the phonon characteristics, and configurational fluctuations make it more negative. The TCR of the liquid and glassy states seems qualitatively consistent with the variation in the structure factor in Ziman's model for pure liquid metals as extended by Nagel to metal alloys and used to explain the negative TCR of a two-component metal glass.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mechanical anisotropy at the nanoscale in amorphous solids

Amorphous solids are randomly disordered without any long-range periodic atomic arrangement and thus appear isotropic. Here, we show in metallic glasses that this view does not hold at small scales: Strong mechanical anisotropy emerges when the sample size decreases below about 15 nm as shown by the marked deviation in stress-strain relations as well as elastic modulus along different loading directions. The size induced mechanical anisotropy is naturally related to structural anisotropy that is absent before loading. The anisotropic stress and modulus versus the size yield different scaling exponents in different stages of deformation, hinting at different deformation mechanisms. The size effect discovered here points to the existence of intrinsic heterogeneity defined by the anisotropy, which may play an important role in structure-property relations in amorphous solids.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermoelectric and mechanical properties on misch metal filled p-type skutterudites Mm{sub 0.9}Fe{sub 4−x}Co{sub x}Sb{sub 12}

Most of the recent work focused on improving the dimensionless figure-of-merit, ZT, of p-type skutterudites uses one or two fillers to tune the electrical and thermal properties. Considering the fact that the different fillers with varying atomic mass and ionic radii can vibrate with different amplitudes to scatter phonons of different mean free paths, we synthesized misch metal filled p-type skutterudites Mm{sub 0.9}Fe{sub 4−x}Co{sub x}Sb{sub 12} (where Mm is La{sub 0.25}Ce{sub 0.5}Pr{sub 0.05}Nd{sub 0.15}Fe{sub 0.03}, called misch metal). The samples were synthesized by hot pressing nano-powder made by ball milling the annealed ingot of Mm{sub 0.9}Fe{sub 4−x}Co{sub x}Sb{sub 12} with varying concentration of cobalt, x. By tuning the Fe/Co ratio, we achieved a thermal conductivity of ∼2 W m{sup −1} K{sup −1} at room temperature and ∼2.3 W m{sup −1} K{sup −1} at about 530 °C and a power factor of ∼30 μW cm{sup −1} K{sup −2} at about 425 °C in Mm{sub 0.9}Fe{sub 3.1}Co{sub 0.9}Sb{sub 12}, leading to a peak ZT ∼1.1 at about 425 °C. The nano-indentation experiment reveals that hardness and elastic modulus of the material is about 4.2 GPa and 116 GPa, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗