Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data parallelism”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Impact Testing of Aluminum 2024 and Titanium 6Al-4V for Material Model Development

One of the difficulties with developing and verifying accurate impact models is that parameters such as high strain rate material properties, failure modes, static properties, and impact test measurements are often obtained from a variety of different sources using different materials, with little control over consistency among the different sources. In addition there is often a lack of quantitative measurements in impact tests to which the models can be compared. To alleviate some of these problems, a project is underway to develop a consistent set of material property, impact test data and failure analysis for a variety of aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the FAA William J. Hughes Technical Center. Unique features of this set of data are that all material property data and impact test data are obtained using identical material, the test methods and procedures are extensively documented and all of the raw data is available. Four parallel efforts are currently underway: Measurement of material deformation and failure response over a wide range of strain rates and temperatures and failure analysis of material property specimens and impact test articles conducted by The Ohio State University; development of improved numerical modeling techniques for deformation and failure conducted by The George Washington University; impact testing of flat panels and substructures conducted by NASA Glenn Research Center. This report describes impact testing which has been done on aluminum (Al) 2024 and titanium (Ti) 6Al-4vanadium (V) sheet and plate samples of different thicknesses and with different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.

Pereira, J. Michael↗
DOE OSTI2022

Toward designing effective exascale scientific computing workflows: experiences and best practices

Many fields within scientific computing have embraced advances in big-data analysis and machine learning, which often requires the deployment of large, distributed and complicated workflows that may combine training neural networks, performing simulations, running inference, and performing database queries and data analysis in asynchronous, parallel and pipelined execution frameworks. Such a shift has brought into focus the need for scalable, efficient workflow management solutions with reproducibility, error and provenance handling, traceability, and checkpoint-restart capabilities, among other needs. Here, we discuss challenges and best-practices for deploying exascale-generation computational science workflows on resources at the Oak Ridge Leadership Computing Facility (OLCF). We present our experiences with large-scale deployment of distributed workflows on the Summit supercomputer, including for bioinformatics and computational biophysics, materials science, and deep learning model optimization. We also present problems and solutions created by working within a Python-centric software base on traditional HPC systems, and discuss steps that will be required before the convergence of HPC, AI, and data science can be fully realized. Our results point to a wealth of exciting new possibilities for harnessing this convergence to tackle new scientific challenges.

Coletti, Mark↗
NASA NTRS1989

Unsteady interaction of a rotor with a vortex

The unsteady, three-dimensional flow field of a helicopter rotor blade encountering a passing vortex is calculated by solving the Euler/thin layer Navier-Stokes equations by a finite-difference numerical procedure. A prescribed vortex method is adopted to preserve the structure of the interacting vortex. The cases considered for computation correspond to the experimental model rotor test conditions of Caradonna, et al. and consist of parallel and oblique interactions. Comparison of the numerical results with test data show good agreement for both parallel and oblique interactions at subsonic and transonic tip speeds.

Srinivasan, G. R.↗
NASA NTRS1989

Evaluating local indirect addressing in SIMD proc essors

In the design of parallel computers, there exists a tradeoff between the number and power of individual processors. The single instruction stream, multiple data stream (SIMD) model of parallel computers lies at one extreme of the resulting spectrum. The available hardware resources are devoted to creating the largest possible number of processors, and consequently each individual processor must use the fewest possible resources. Disagreement exists as to whether SIMD processors should be able to generate addresses individually into their local data memory, or all processors should access the same address. The tradeoff is examined between the increased capability and the reduced number of processors that occurs in this single instruction stream, multiple, locally addressed, data (SIMLAD) model. Factors are assembled that affect this design choice, and the SIMLAD model is compared with the bare SIMD and the MIMD models.

Middleton, David↗
DOE OSTI2021

Interactive Web Application for Traffic Simulation Data Management and Visualization

As traffic simulation software becomes more effective for realistically simulating and analyzing traffic dynamics and vehicle interactions on the mesoscopic and microscopic level, the management, dissemination, and collaborative visualization of traffic simulation results produced by individual transportation planners presents a significant challenge. Existing online content management systems have a very limited capability in allowing users to query specific traffic simulation scenarios and geospatially visualize simulation results through shareable and interactive web interfaces. This paper presents a web-based application for promoting the archiving, sharing, and visualization of large-scale traffic simulation outputs. The application is developed to enhance cyber-physical controls, communications, and public education for collaborative transportation planning. Unique features of the web application include: (a) allowing users to upload their new traffic simulation scenarios (parameters and outputs), as well as search existing scenarios using easily accessible interfaces; (b) optimizing simulation output files with heterogeneous data formats and projected coordinate systems for web-based storage and management using a scalable and searchable data/metadata standard; (c) standardizing user-uploaded simulation outputs using web interfaces and data processing libraries with parallel computing capacity; and (d) providing shareable web visual interfaces for visualizing the traffic flow and signal information stored in simulation outputs (e.g., regional traffic patterns and individual vehicle interactions) and visually comparing multiple simulation outputs both spatially and temporally. Furthermore, the paper presents the conceptual design and implementation of this application, and demonstrates the application’s performance for sharing, comparing, and visualizing simulation outputs from VISSIM and SUMO, two commonly used traffic simulation software programs.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗
DOE OSTI2022

Measurement of the 240 Pu(n,f) Prompt Fission Neutron Spectra with Chi-Nu

The DOE Nuclear Criticality Safety Program has funded a multi-year effort to measure the 240 Pu(n,f) Prompt Fission Neutron Spectrum at Chi-Nu. This project is a joint LANL-LLNL effort, involving the preparation of 12 240 Pu foils and construction of a Parallel-Plate Avalanche Counter at LLNL, with subsequent measurements of the 240 Pu(n,f) PFNS at the Chi-Nu beamline at the Los Alamos Neutron Science Center’s Weapons Neutron Research facility (LANSCE/WNR). We expect the PPAC to be ready in time to perform the measurements this run cycle.

240Pu Foils↗
NASA NTRSDate not supplied

Alternative Setup for Long-Duration Low-Duty-Cycle 600°C Ambient Testing of SiC Integrated Circuits

A scalable, compact oven testbed system for simultaneously evaluating a multitude of high temperature integrated circuits (ICs) for prolonged operating times of up to 600 °C has been prototyped. The new testbed system enables long-duration high temperature testing in sufficient statistical quantities consistent with standard aerospace electronics engineering standards. This setup is comprised of multiple compact ovens housing chips or packages mounted to ceramic circuit boards. Each oven is a compact 15.2 cm length by 15.2 cm width by 12.7 cm depth with a maximum 400 Watts of heating power. The custom-made silicon oxide ceramic heating block inside each oven is based on a 3D printed design adapted for the easy insertion of the IC device under test (DUT). This innovative design provides the quick insertion of ICs with or without a ceramic package into a 600 °C environment by utilizing a movable 11.43 cm long ceramic substrate with electrical traces extending from the oven hot zone to external standard plastic-based board connectors. Another key oven design feature is the minimization of the DUT exposure to electromagnetic interference (EMI) by utilizing a filtered DC power source to reduce heating element noise. Additionally, the ovens can be configured in a parallel arrangement allowing global data monitoring over a single industrial RS422 serial port. This feature is important for scaling up to test multiple ICs semi-simultaneously. A USB serial port is provided to independently control the operating parameters of each oven such as the oven target temperature and oven ramp rate. The oven temperature can reach up to 600 °C with a confirmed +/- 4 °C maximum deviation across the test zone region. The ramp rate can be programmed from 1 °C/minute up to 10 °C/minute. Furthermore, a programmable switchboard is used to interface with the DUT. This switchboard comprises a National Instruments Peripheral Component Interconnect eXtension for Instrumentation (NI PXI) system and a breakout board to send and receive power, analog or digital test signals. By using this unique oven testbed system, a variety of ICs can now be tested in parallel using the same test components configured for a diverse set of requirements.

DC Powered Oven↗
NASA NTRS1998

PLUM: Parallel Load Balancing for Unstructured Adaptive Meshes

Dynamic mesh adaption on unstructured grids is a powerful tool for computing large-scale problems that require grid modifications to efficiently resolve solution features. Unfortunately, an efficient parallel implementation is difficult to achieve, primarily due to the load imbalance created by the dynamically-changing nonuniform grid. To address this problem, we have developed PLUM, an automatic portable framework for performing adaptive large-scale numerical computations in a message-passing environment. First, we present an efficient parallel implementation of a tetrahedral mesh adaption scheme. Extremely promising parallel performance is achieved for various refinement and coarsening strategies on a realistic-sized domain. Next we describe PLUM, a novel method for dynamically balancing the processor workloads in adaptive grid computations. This research includes interfacing the parallel mesh adaption procedure based on actual flow solutions to a data remapping module, and incorporating an efficient parallel mesh repartitioner. A significant runtime improvement is achieved by observing that data movement for a refinement step should be performed after the edge-marking phase but before the actual subdivision. We also present optimal and heuristic remapping cost metrics that can accurately predict the total overhead for data redistribution. Several experiments are performed to verify the effectiveness of PLUM on sequences of dynamically adapted unstructured grids. Portability is demonstrated by presenting results on the two vastly different architectures of the SP2 and the Origin2OOO. Additionally, we evaluate the performance of five state-of-the-art partitioning algorithms that can be used within PLUM. It is shown that for certain classes of unsteady adaption, globally repartitioning the computational mesh produces higher quality results than diffusive repartitioning schemes. We also demonstrate that a coarse starting mesh produces high quality load balancing, at a fraction of the cost required a fine initial mesh. Results indicate that our parallel load balancing strategy will remain viable on large numbers of processors.

Oliker, Leonid↗
DOE OSTI2021

Productive Programming of Distributed Systems with the SHAD C++ Library

High-performance computing (HPC) is often perceived as a matter of making large-scale systems (e.g., clusters) run as fast as possible, regardless the required programming effort. However, the idea of "bringing HPC to the masses" has recently emerged. Inspired by this vision, we have designed SHAD, the Scalable High-performance Algorithms and Data-structures library. SHAD is open source software, written in C++, for C++ developers. Unlike other HPC libraries for distributed systems, which rely on SPMD models, SHAD adopts a shared-memory programming abstraction, to make C++ programmers feel at home. Underneath, SHAD manages tasking and data-movements, moving the computation where data resides and taking advantage of asynchrony to tolerate network latency. At the bottom of his stack, SHAD can interface with multiple runtime systems: this not only improves developer’s productivity, by hiding the complexity of such software and of the underlying hardware, but also greatly enhance code portability. Thanks to its abstraction layers, SHAD can indeed target different systems, ranging from laptops to HPC clusters, without any need for modifying the user-level code. We have prototyped and open-sourced the implementation of (a subset of) the C++ standard library (STL) targeting multi-node HPC clusters. Our work allows plain STL-based C++ code to scale on HPC systems, with no need for rewriting the code to exploit the complex hardware. SHAD is available under Apache v2 License at https://github.com/pnnl/SHAD. In this paper we overview the design of the SHAD library, depicting its main components: runtime systems abstractions for tasking; parallel and distributed data-structures; STL-compliant interfaces and algorithms.

Castellana, Vito G.↗
NASA NTRS1980

Parallel processing implementations of a contextual classifier for multispectral remote sensing data

Contextual classifiers are being developed as a method to exploit the spatial/spectral context of a pixel to achieve accurate classification. Classification algorithms such as the contextual classifier typically require large amounts of computation time. One way to reduce the execution time of these tasks is through the use of parallelism. The applicability of the CDC flexible processor system and of a proposed multimicroprocessor system (PASM) for implementing contextual classifiers is examined.

Siegel, H. J.↗
DOE OSTI2021

FasTensor (FT) v0.0.1

The FasTensor implements the native array data programming mode namely SLOPE for modern data analysis tasks. It is designed to work in parallel on supercomputer and can handle terabyte data analysis tasks. It is thousand times faster than other data analysis systems such as Apache Spark and 38% faster than TensorFlow in dealing with large scale scientific data analysis. It has wide applications in image data analysis and mesh data analysis tasks in physical simulations and other fields.

Wu, Kesheng↗
NASA NTRS2017

4BMS-X Design and Test Activation

In support of the NASA goals to reduce power, volume and mass requirements on future CO2 (Carbon Dioxide) removal systems for exploration missions, a 4BMS (Four Bed Molecular Sieve) test bed was fabricated and activated at the NASA Marshall Space Flight Center. The 4BMS-X (Four Bed Molecular Sieve-Exploration) test bed used components similar in size, spacing, and function to those on the flight ISS flight CDRA system, but were assembled in an open framework. This open framework allows for quick integration of changes to components, beds and material systems. The test stand is highly instrumented to provide data necessary to anchor predictive modeling efforts occurring in parallel to testing. System architecture and test data collected on the initial configurations will be presented.

Peters, Warren T.↗
NASA NTRS1994

Dynamic Load Balancing For Grid Partitioning on a SP-2 Multiprocessor: A Framework

Computational requirements of full scale computational fluid dynamics change as computation progresses on a parallel machine. The change in computational intensity causes workload imbalance of processors, which in turn requires a large amount of data movement at runtime. If parallel CFD is to be successful on a parallel or massively parallel machine, balancing of the runtime load is indispensable. Here a framework is presented for dynamic load balancing for CFD applications, called Jove. One processor is designated as a decision maker Jove while others are assigned to computational fluid dynamics. Processors running CFD send flags to Jove in a predetermined number of iterations to initiate load balancing. Jove starts working on load balancing while other processors continue working with the current data and load distribution. Jove goes through several steps to decide if the new data should be taken, including preliminary evaluate, partition, processor reassignment, cost evaluation, and decision. Jove running on a single IBM SP2 node has been completely implemented. Preliminary experimental results show that the Jove approach to dynamic load balancing can be effective for full scale grid partitioning on the target machine IBM SP2.

Sohn, Andrew↗
NASA NTRS1994

Dynamic Load Balancing for Grid Partitioning on a SP-2 Multiprocessor: A Framework

Computational requirements of full scale computational fluid dynamics change as computation progresses on a parallel machine. The change in computational intensity causes workload imbalance of processors, which in turn requires a large amount of data movement at runtime. If parallel CFD is to be successful on a parallel or massively parallel machine, balancing of the runtime load is indispensable. Here a framework is presented for dynamic load balancing for CFD applications, called Jove. One processor is designated as a decision maker Jove while others are assigned to computational fluid dynamics. Processors running CFD send flags to Jove in a predetermined number of iterations to initiate load balancing. Jove starts working on load balancing while other processors continue working with the current data and load distribution. Jove goes through several steps to decide if the new data should be taken, including preliminary evaluate, partition, processor reassignment, cost evaluation, and decision. Jove running on a single EBM SP2 node has been completely implemented. Preliminary experimental results show that the Jove approach to dynamic load balancing can be effective for full scale grid partitioning on the target machine IBM SP2.

Sohn, Andrew↗
NASA NTRS1994

Dynamic Load Balancing for Finite Element Calculations on Parallel Computers

Computational requirements of full scale computational fluid dynamics change as computation progresses on a parallel machine. The change in computational intensity causes workload imbalance of processors, which in turn requires a large amount of data movement at runtime. If parallel CFD is to be successful on a parallel or massively parallel machine, balancing of the runtime load is indispensable. Here a frame work is presented for dynamic load balancing for CFD applications, called Jove. One processor is designated as a decision maker Jove while others are assigned to computational fluid dynamics. Processors running CFD send flags to Jove in a predetermined number of iterations to initiate load balancing. Jove starts working on load balancing while other processors continue working with the current data and load distribution. Jove goes through several steps to decide if the new data should be taken, including preliminary evaluate, partition, processor reassignment, cost evaluation, and decision. Jove running on a single SP2 node has been completely implemented. Preliminary experimental results show that the Jove approach to dynamic load balancing can be effective for full scale grid partitioning on the target machine SP2.

Pramono, Eddy↗
NASA NTRS1993

Feed-forward volume rendering algorithm for moderately parallel MIMD machines

Algorithms for direct volume rendering on parallel and vector processors are investigated. Volumes are transformed efficiently on parallel processors by dividing the data into slices and beams of voxels. Equal sized sets of slices along one axis are distributed to processors. Parallelism is achieved at two levels. Because each slice can be transformed independently of others, processors transform their assigned slices with no communication, thus providing maximum possible parallelism at the first level. Within each slice, consecutive beams are incrementally transformed using coherency in the transformation computation. Also, coherency across slices can be exploited to further enhance performance. This coherency yields the second level of parallelism through the use of the vector processing or pipelining. Other ongoing efforts include investigations into image reconstruction techniques, load balancing strategies, and improving performance.

Yagel, Roni↗
NASA NTRS1984

Plasma and energetic particle structure upstream of a quasi-parallel interplanetary shock

ISEE 1, 2 and 3 data from 1978 on interplanetary magnetic fields, shock waves and particle energetics are examined to characterize a quasi-parallel shock. The intense shock studied exhibited a 640 km/sec velocity. The data covered 1-147 keV protons and electrons and ions with energies exceeding 30 keV in regions both upstream and downstream of the shock, and also the magnitudes of ion-acoustic and MHD waves. The energetic particles and MHD waves began being detected 5 hr before the shock. Intense halo electron fluxes appeared ahead of the shock. A closed magnetic field structure was produced with a front end 700 earth radii from the shock. The energetic protons were cut off from the interior of the magnetic bubble, which contained a markedly increased density of 2-6 keV protons as well as the shock itself.

Kennel, C. F.↗
NASA NTRS1984

Data flow modeling techniques

There have been a number of simulation packages developed for the purpose of designing, testing and validating computer systems, digital systems and software systems. Complex analytical tools based on Markov and semi-Markov processes have been designed to estimate the reliability and performance of simulated systems. Petri nets have received wide acceptance for modeling complex and highly parallel computers. In this research data flow models for computer systems are investigated. Data flow models can be used to simulate both software and hardware in a uniform manner. Data flow simulation techniques provide the computer systems designer with a CAD environment which enables highly parallel complex systems to be defined, evaluated at all levels and finally implemented in either hardware or software. Inherent in data flow concept is the hierarchical handling of complex systems. In this paper we will describe how data flow can be used to model computer system.

Kavi, K. M.↗