Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cross Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Flutter of laminated plates in supersonic flow

A solution procedure was developed using linear small deflection theory for the flutter of simply supported laminated plates. For such plates, the bending and extensional governing equations are coupled and have cross-stiffness terms which do not appear in classical plate theory. An extended Galerkin method is used to obtain approximate solutions to the governing equations, and the aerodynamic pressure loading used in the analysis is that given by linear piston theory with flow at arbitrary cross-flow angle. A limited parametric study was conducted for typical laminated composite plates. The calculations show that both the bending-extensional coupling and the cross-stiffness terms have a large destabilizing effect on flutter. Since classical plate theory does not consider bending-extensional coupling and cross stiffness terms, it usually gives inaccurate and nonconservative flutter boundaries for laminated plates.

Sawyer, J. W.↗
NASA NTRS1978

Lifting line theory for transonic flow

Lifting line theory is applied to describe the flow about a lifting wing at transonic speeds. The method extends that of Van Dyke (1975), in which lifting line theory is viewed as a singular perturbation problem, to transonic flows. Inner and outer expansions as the aspect ratio approaches infinity of the transonic small disturbance equations are found. It is shown that the solutions match asymptotically. A boundary value problem is formulated which describes the first aspect ratio correction to the two dimensional cross sectional transonic flow. The theory is especially applicable to wings of similar cross-sections.

Cook, L. P.↗
NASA NTRS1990

Extreme energetic particle decreases near geostationary orbit - A manifestation of current diversion within the inner plasma sheet

A qualitative model of cross-tail current flow is considered. It is suggested that when magnetic reconnection begins, the current effectively flows across the plasma sheet both earthward and tailward of the disruption region near the neutral line. It is shown that an enhanced cross-tail current earthward of this region would thin the plasma sheet substantially due to the magnetic pinch effect. The results explain the very taillike field and extreme particle dropouts often seen late in substorm growth phases.

Baker, D. N.↗
NASA NTRSDate not supplied

Development of a Trajectory-Centric CFD-RBD Framework for Advanced Multidisciplinary/Multiphysics Simulation

The desire to model increasingly complex unsteady flow phenomena drives coupling of physics-based disciplinary analysis tools, such as coupled aerodynamics-rigid body dynamics simulations. This paper documents the creation of a framework linking the six-degree-of-freedom trajectory propagator POST2 with NASA’s FUN3D computational fluid dynamics flow solver. Cross-code verification between the framework and a CFD-centric 6DOF code is performed using the Army-Navy Finner projectile experiencing unsteady accelerating flow. Free-flight simulations of an entry vehicle ballistic range test are validated against physical and computational experiments.

Zachary J Ernst↗
NASA NTRSDate not supplied

Development of a Trajectory-Centric CFD-RBD Framework for Advanced Multidisciplinary/Multiphysics Simulation

The desire to model increasingly complex unsteady flow phenomena drives coupling of physics-based disciplinary analysis tools, such as coupled aerodynamics-rigid body dynamics simulations. This paper documents the creation of a framework linking the six-degree-of-freedom trajectory propagator POST2 with NASA’s FUN3D computational fluid dynamics flow solver. Cross-code verification between the framework and a CFD-centric 6DOF code is performed using the Army-Navy Finner projectile experiencing unsteady accelerating flow. Free-flight simulations of an entry vehicle ballistic range test are validated against physical and computational experiments.

Zachary J Ernst↗
NASA NTRS1982

Developing flow in S-shaped ducts. 1: Square cross-section duct

Laser-Doppler velocimetry was used to measure the laminar and turbulent flow in an S-duct formed with two 22.5 deg sectors of a bend with ratio of mean radius of curvature to hydraulic diameter of 7.0. The boundary layers at the inlet to the bend were about 25% and 15% of the hydraulic diameter for the laminar and turbulent flows, respectively. Pressure-driven secondary flows develop in the first half of the S-duct and persist into the second half but are largely reversed by the exit plane as a consequence of the change in the sense of curvature. There is, however, a region near the outer wall of the second bend where the redistribution of the streamwise isotachs results in a reinforcement of the secondary flow which was established in the first half of the S-duct. The net redistribution of the streamwise isotachs is comparable to that occurring in unidirectional bends of stronger curvature. The wall pressure distribution was also measured for the turbulent flow and quantifies the expected large variations in the longitudinal pressure gradient distributions which occur at different radial locations.

Taylor, A. M. K. P.↗
NASA NTRS2013

Laminar, Transitional, and Turbulent Heating on Mid Lift-to-Drag Ratio Entry Vehicles

The boundary-layer transition characteristics and convective aeroheating levels on mid lift-to-drag ratio entry vehicle configurations have been studied through wind-tunnel testing. Several configurations were investigated, including elliptically blunted cylinders with both circular and elliptically flattened cross sections, biconic geometries based on launch vehicle dual-use shrouds, and parametrically optimized analytic geometries. Vehicles of this class have been proposed for high-mass Mars missions, such as sample return and crewed exploration, for which the conventional sphere-cone entry-vehicle geometries of previous Mars missions are insufficient. Testing was conducted at Mach 6 over a range of Reynolds numbers sufficient to generate laminar, transitional, and turbulent flow. Transition onset locations, both straight-line and cross-flow, and heating rates were obtained through global phosphor thermography. Supporting computations were performed to obtain heating rates for comparison with the data. Laminar data and predictions agreed to well within the experimental uncertainty. Fully turbulent data and predictions also agreed well. However, in transitional flow regions, greater differences were observed.

Hollis, Brian R.↗
NASA NTRS1998

Static Thrust and Vectoring Performance of a Spherical Convergent Flap Nozzle with a Nonrectangular Divergent Duct

The static internal performance of a multiaxis-thrust-vectoring, spherical convergent flap (SCF) nozzle with a non-rectangular divergent duct was obtained in the model preparation area of the Langley 16-Foot Transonic Tunnel. Duct cross sections of hexagonal and bowtie shapes were tested. Additional geometric parameters included throat area (power setting), pitch flap deflection angle, and yaw gimbal angle. Nozzle pressure ratio was varied from 2 to 12 for dry power configurations and from 2 to 6 for afterburning power configurations. Approximately a 1-percent loss in thrust efficiency from SCF nozzles with a rectangular divergent duct was incurred as a result of internal oblique shocks in the flow field. The internal oblique shocks were the result of cross flow generated by the vee-shaped geometric throat. The hexagonal and bowtie nozzles had mirror-imaged flow fields and therefore similar thrust performance. Thrust vectoring was not hampered by the three-dimensional internal geometry of the nozzles. Flow visualization indicates pitch thrust-vector angles larger than 10' may be achievable with minimal adverse effect on or a possible gain in resultant thrust efficiency as compared with the performance at a pitch thrust-vector angle of 10 deg.

Wing, David J.↗
NASA NTRS2012

Laminar, Transitional, and Turbulent Heating on Mid Lift-to-Drag Ratio Entry Vehicles

The boundary-layer transition characteristics and convective aeroheating levels on mid lift-to-drag ratio entry vehicle configurations have been studied through wind tunnel testing. Several configurations were investigated, including elliptically-blunted cylinders with both circular and elliptically-flattened cross sections, biconic geometries based on launch vehicle dual-use shrouds, and parametrically-optimized analytic geometries. Vehicles of this class have been proposed for high-mass Mars missions, such as sample return and crewed exploration, for which the conventional sphere-cone entry-vehicle geometries of previous Mars missions are insufficient. Testing was conducted at Mach 6 over a range of Reynolds numbers sufficient to generate laminar, transitional, and turbulent flow. Transition onset locations - both straight-line and cross-flow - and heating rates were obtained through global phosphor thermography. Supporting computations were performed to obtain heating rates for comparison with the data. Laminar data and predictions agreed to well within the experimental uncertainty. Fully-turbulent data and predictions also agreed well. However, in transitional flow regions, greater differences were observed. Additional aerodynamic performance data were also generated through Modified-Newtonian analyses of the geometries.

Hollis, Brian R.↗
NASA NTRS1980

Variability of plasma sheet dynamics

IMP 7 observations of plasma sheet structure and dynamics made during a 24-h period in which the satellite traversed the tail plasma sheet at a radial distance of 35 earth radii and remained within 2 earth radii of the expected position at the neutral sheet and in which at least five substorms occured on the ground are presented. High-time-resolution measurements of the magnetic field, plasma flow and greater than 50-keV protons obtained by the satellite and ground-based magnetic measurements are discussed for a 4-hr interval in which two small substorms occurred, a 6-hr geomagnetically quiet interval in which moderate variable plasma flows were observed, a very rapid, smooth neutral sheet crossing and earthward plasma flow during the expansion phase of a small substorm, a moderate-size substorm in which a prolonged interval of field-aligned tailward flow commenced at onset, a strong tailward and dawnward flow burst in an interval between substorms and a large substorm in which strong tailward flow was observed. Observations indicate the significant distortion of the tail field, possibly by plasma flow stresses, a neutral sheet structure occasionally resembling the hydromagnetic rotational discontinuity and a high level of magnetic turbulence during an earthward plasma flow which may contribute towards plasma sheet dissipation.

Coroniti, F. V.↗
NASA NTRS1992

Direct simulation of high-speed mixing layers

A computational study of a nonreacting high-speed mixing layer is performed. A higher order algorithm with sufficient grid points is used to resolve all relevant scales. In all cases, a temporal free-stream disturbance is introduced. The resulting flow is time-sampled to generate a statistical cross section of the flow properties. The studies are conducted at two convective Mach numbers, three free-stream turbulence intensities, three Reynolds numbers, and two types of initial profiles-hyperbolic tangent (tanh) and boundary layer. The boundary-layer profile leads to more realistic predictions of the transition processes. The predicted transition Reynolds number of 0.18 x 10(exp 6) compares well with experimental data. Normalized vortex spacings for the boundary-layer case are about 3.5 and compare favorably with the 1.5 to 2.5 found in experimental measurements. The tanh profile produces spacings of about 10. The growth rate of the layer is shown to be moderately affected by the initial disturbance field, but comparison with experimental data shows moderate agreement. For the boundary-layer case, it is shown that noise at the Strouhal number of 0.007 is selectively amplified and shows little Reynolds number dependence.

Mukunda, H. S.↗
NASA NTRS1993

CFD analyses of coolant channel flowfields

The flowfield characteristics in rocket engine coolant channels are analyzed by means of a numerical model. The channels are characterized by large length to diameter ratios, high Reynolds numbers, and asymmetrical heating. At representative flow conditions, the channel length is approximately twice the hydraulic entrance length so that fully developed conditions would be reached for a constant property fluid. For the supercritical hydrogen that is used as the coolant, the strong property variations create significant secondary flows in the cross-plane which have a major influence on the flow and the resulting heat transfer. Comparison of constant and variable property solutions show substantial differences. In addition, the property variations prevent fully developed flow. The density variation accelerates the fluid in the channels increasing the pressure drop without an accompanying increase in heat flux. Analyses of the inlet configuration suggest that side entry from a manifold can affect the development of the velocity profile because of vortices generated as the flow enters the channel. Current work is focused on studying the effects of channel bifurcation on the flow field and the heat transfer characteristics.

Yagley, Jennifer A.↗
NASA NTRS1961

An Experimental Study of Continuous Plasma Flows Driven by a Confined Arc in a Transverse Magnetic Field

A crossed-field, continuous-flow plasma accelerator has been built and operated. The highest measured velocity of the flow, which was driven by the interaction of the electric and magnetic fields, was about 500 meters per second. Some of the problems discussed are ion slip, stability and uniformity of the discharge, effect of the magnetic field on electron emission, use of preionization, and electrode contamination.

Barger, R. L.↗
NASA NTRS2018

New Results from Galileo's First Flyby of Ganymede: Reconnection-Driven Flows at the Low-Latitude Magnetopause Boundary, Crossing the Cusp, and Icy Ionospheric Escape

On 27 June 1996, the NASA Galileo spacecraft made humanity’s first flyby of Jupiter’s largest moon, Ganymede, discovering that it is the only moon known to possess an internally generated magnetic field. Resurrecting the original Galileo Plasma Subsystem (PLS) data analysis software, we processed the raw PLS data from G01 and for the first time present the properties of plasmas encountered. Entry into the magnetosphere of Ganymede occurred near the confluence of the magnetopause and plasma sheet. Reconnection-driven plasma flows were observed (consistent with an Earth-like Dungey cycle), which may be a result of reconnection in the plasma sheet, magnetopause, or might be Ganymede’s equivalent of a Low-Latitude Boundary Layer. Dropouts in plasma density combined with velocity perturbations afterward suggest that Galileo briefly crossed the cusps into closed magnetic field lines. Galileo then crossed the cusps, where field-aligned precipitating ions were observed flowing down into the surface, at a location consistent with observations by the Hubble Space Telescope. The density of plasma outflowing from Ganymede jumped an order of magnitude around closest approach over the north polar cap. The abrupt increase may be a result of crossing the cusp or may represent an altitude-dependent boundary such as an ionopause. More diffuse, warmer field-aligned outflows were observed in the lobes. Fluxes of particles near the moon on the nightside were significantly lower than on the dayside, possibly resulting from a diurnal cycle of the ionosphere and/or neutral atmosphere.

Collinson, Glyn↗
NASA NTRS1983

Flow in coronal loops with a mass source

This research studies the flow of plasma inside a coronal loop in which an injection of plasma through the lateral surface is permitted. The flow is assumed steady and polytropic. The problem covers two cases: (a) upflow at one footpoint, downflow at the other; (b) downflow at both footpoints. The first case can be shown to be quite similar to that of a mass-conserving flow with variable cross section; the second, instead, is characterized by solutions with a different type of topology; its main new feature is the obvious fact that all the solutions pass through a single point going from negative to positive velocities. In this second case the density ratio between footpoints and top can be much smaller than in a mass conserving flow. This can explain some properties of observed loops.

Noci, G.↗
NASA NTRS1989

Semidiscrete Galerkin modelling of compressible viscous flow past a circular cone at incidence

A numerical study of the laminar and compressible boundary layer, about a circular cone in a supersonic free stream, is presented. It is thought that if accurate and efficient numerical schemes can be produced to solve the boundary layer equations, they can be joined to numerical codes that solve the inviscid outer flow. The combination of these numerical codes is competitive with the accurate, but computationally expensive, Navier-Stokes schemes. The primary goal is to develop a finite element method for the calculation of 3-D compressible laminar boundary layer about a yawed cone. The proposed method can, in principle, be extended to apply to the 3-D boundary layer of pointed bodies of arbitrary cross section. The 3-D boundary layer equations governing supersonic free stream flow about a cone are examined. The 3-D partial differential equations are reduced to 2-D integral equations by applying the Howarth, Mangler, Crocco transformations, a linear relation between viscosity, and a Blasius-type of similarity variable. This is equivalent to a Dorodnitsyn-type formulation. The reduced equations are independent of density and curvature effects, and resemble the weak form of the 2-D incompressible boundary layer equations in Cartesian coordinates. In addition the coordinate normal to the wall has been stretched, which reduces the gradients across the layer and provides high resolution near the surface. Utilizing the parabolic nature of the boundary layer equations, a finite element method is applied to the Dorodnitsyn formulation. The formulation is presented in a Petrov-Galerkin finite element form and discretized across the layer using linear interpolation functions. The finite element discretization yields a system of ordinary differential equations in the circumferential direction. The circumferential derivatives are solved by an implicit and noniterative finite difference marching scheme. Solutions are presented for a 15 deg half angle cone at angles of attack of 5 and 10 deg. The numerical solutions assume a laminar boundary layer with free stream Mach number of 7. Results include circumferential distribution of skin friction and surface heat transfer, and cross flow velocity distributions across the layer.

Meade, Andrew James, Jr.↗
NASA NTRS1983

Modified shielding jet model for twin-jet shielding analysis

An analytical model to estimate the shielding of noise emitted from a point noise source has been developed assuming the shielding jet to be a cylinder of constant radius with uniform flow across the cross section. Comparison to experiment indicated that the model overestimates diffraction of sound around the jet in the far downstream region. The shielding jet model is modified to include widening downstream of the nozzle exit. This not only represents a more realistic model of the jet, but is also expected to improve the shielding estimate downstream. The modified jet model incorporates a Mach number dependent widening rate, a corresponding decrease in flow velocity downstream and an equivalent slug flow evaluation to retain the locally parallel flow approximation of the model development. The shielding analysis with modified jet model is compared to measured data for a subsonic isothermal air jet and a simulated hot subsonic jet. Improvement of the shielding estimate is discussed.

Gerhold, C. H.↗