Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CONTACT RESISTANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Impacts of Curing-Induced Phase Segregation in Silicon Nanoparticle-Based Electrodes

We report the investigation of silicon nanoparticle composite anodes for Li-ion batteries, using a combination of two nm-scale atomic force microscopy-based techniques: scanning spreading resistance microscopy for electrical conduction mapping and contact resonance and force volume for elastic modulus mapping, along with scanning electron microscopy-based energy dispersion spectroscopy, nanoindentation, and electrochemical analysis. Thermally curing the composite anode—made of polyethylene oxide-treated Si nanoparticles, carbon black, and polyimide binder—reportedly improves the anode electrochemical performance significantly. This work demonstrates phase segregation resulting from thermal curing, where alternating bands of carbon and silicon active material are observed. This electrode morphology is retained after extensive cycling, where the electrical conduction of the carbon-rich bands remains relatively unchanged, but the mechanical modulus of the bands decreases distinctly. These electrical and mechanical factors may contribute to performance improvement, with carbon bands serving as a mechanical buffer for Si deformation and providing electrical conduction pathways. This work motivates future efforts to engineer similar morphologies for mitigating capacity loss in silicon electrodes.

25 ENERGY STORAGE↗
NASA NTRS1985

Rolling contact fatigue behavior of Cu and TiN coatings on bearing steel substrates

The resistance of copper and TiN coatings on various bearing substrates to high-load rolling contact fatigue (RCF) is investigated. Special attention is given to the lubricating characteristics of copper deposited by ion plating, and the wear resistant characteristics of TiN deposited by ion plating and magnetron sputtering techniques. RCF samples of 440C and AMS 5749 bearing steels were coated. Sputter deposited and ion plated films were on the RCF samples in a range of thickness from about 2000 A to 2 microns. Results showed a marked improvement of the RCF for pure copper tested on 440C, but a degradation for copper on AMS 5749. It is also found that the 2000 A TiN films behave favorably on the 440C and AMS 5749 bearing steels at RCF stress levels of 786 ksi. Scanning electron microscopy, X-ray diffraction, and electron spectroscopy for chemical analysis were used during the investigation.

Hochman, R. F.↗
NASA NTRSDate not supplied

Understanding Thermal Transport in Polymer - Silver Nanowire Composites

Understanding thermal transport across filler-polymer interfaces and filler-filler contacts within polymer composites is of great importance for better thermal design of the composites that are widely used in high-performance heat exchangers, energy storage devices, and flexible electronics. Over the past several decades, considerable progress has been made in improving the thermal conductivity of polymer composites, but several key questions concerning the influence of interfacial thermal resistance, or Kapitza resistance, still remain. Firstly, the thermal properties of these composites are highly dependent on thermal transport through the filler network and its contacts. For metallic nanofillers, the thermal conductivity is often estimated using the Wiedemann-Franz law based on electrical conductivity; however, it remains a question whether the Wiedemann-Franz law still holds at nanoscale contacts. Through investigation of silver nanowires of varying sizes, we were able to demonstrate that the Lorenz number for silver nanowire increases with decreasing nanowire diameter. Examination of the corresponding electrical and thermal conductivities indicate that these changes are due to that the relative contribution of phonons becomes more significant as a result of elastic stiffening. Furthermore, we show that for silver nanowires, the contact thermal resistance is ~8 times lower than that of multi-walled carbon nanotube (MWCNT) of similar diameters. Additionally, through systematic studies of electrospun polymer-silver nanowire composite nanofibers, we investigated the impact of interface morphology on the thermal conductivity enhancement of the composite system and probed the value of the Kapitza resistance for individual polymer-filler interfaces. For polymer nanofibers containing continuous, single silver nanowires, the thermal conductivity increases linearly with increasing volume fraction of silver, which is consistent with the prediction of percolation theory for samples above the percolation limit. By comparing this linear trend to the measured thermal conductivities of composite nanofibers with more complex structures, we were able to determine the resistance associated with any additional polymer-filler boundaries. In doing so we find that the thermal boundary resistance for polyvinylpyrrolidone (PVP)–silver interfaces is significantly lower than that of comparable polymer-MWCNT composite systems. Together our studies provide new insights into thermal transport in polymer nanocomposites and should help facilitate the design of high performance polymeric thermal interface material.

Matthew L. Fitzgerald↗
NASA NTRS1992

Eliminating Deadbands In Resistive Angle Sensors

Proposed shaft-angle-measuring circuit provides continuous indication of angle of rotation from 0 degree to 360 degrees. Sensing elements are two continuous-rotation potentiometers, and associated circuitry eliminates deadband that occurs when wiper contact of potentiometer crosses end contacts near 0 degree position of circular resistive element. Used in valve-position indicator or similar device in which long operating life and high angular precision not required.

Salomon, Phil M.↗
NASA NTRS1988

Experiences in extraction of contact parameters from process-evaluation test-structures

Six-terminal-contact test structures are introduced for characterizing ohmic contacts between a metal and a heavily doped semiconductor layer. Specifically, the six-terminal test structure supplies the additional information needed in order to calculate the transmission length and eventual corrections to the characteristic resistance per unit width due to finite contact length. The essential feature of this test structure is a square contact with four taps in the lower (semiconductor) layer. Every other one of these taps is used for current injection ('front'). From the voltage drop at the opposite tap and the side taps, the 'end' resistance and the 'side' resistances are calculated. The test structures are shown to give valuable information complementary to the common front resistance measurements. The interfacial resistivity is obtained directly after proper correction for flange effects.

Lieneweg, Udo↗
DOE OSTI2023

An effective air–liquid contactor for CO 2 direct air capture using aqueous solvents

Here, the development of a cost-effective, corrosion resistant, high-flux direct air capture (HiDAC) contactor for a solvent-based direct air capture (DAC) process is reported. Literature technoeconomic analyses suggest that the air–liquid contactor can cost over 20 % of the overall DAC plant’s annualized capital costs. To bring down the overall cost of DAC, it is imperative that an effective contactor is developed. A hybrid contactor consisting of a commercial polyvinylchloride structured packing enhanced with stainless-steel 410 random packing has been developed to provide a high surface area for air–liquid contact. The contactor geometry, wettability, corrosion resistance, pressure drop, along with its CO 2 uptake efficiency, CO 2 uptake rates, and extended loading potential using potassium sarcosinate solutions are investigated. Results show that the HiDAC contactor has a relatively high specific surface area (885 m 2 /m 3 ), which allows for CO 2 uptake efficiencies of up to 75 % and capture rates of up to 550 g of CO 2 per day for a 0.3 × 0.25 × 0.3 m contactor. The contactor also exhibits high levels of wettability and corrosion resistance with amino acid-based DAC solvents. A CO 2 uptake model was developed, and modeling results are compared to experimental data to simulate and predict the performance of the contactor in a DAC process using potassium sarcosinate solvent. The system’s overall mass transfer coefficient and theoretical pressure drop were also calculated, and these results were compared to DAC data found in literature. The results presented indicate that the HiDAC contactor is well suited for DAC due to its high specific surface area, resistance to corrosion, and high degree of wettability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1978

Growth, evaluation and modeling of silicon-on-ceramic solar cells

The silicon-on-ceramic (SOC) process uses inexpensive ceramic substrates to provide supported growth of silicon from the melt. The conditions for unidirectional solidification, the grain structure and other properties are quite similar to those of EFG silicon ribbon. Solar cells with interdigital electrodes have demonstrated AMl conversion efficiencies (active area) of 7.8% without AR coatings and 10.1% efficiencies with an AR coating of SiO. Mathematical modeling of the series resistance of cells shows the feasibility of making electrical contact to the base layer of the cell through slots in the substrate. However, series resistance in the base layer sets an upper limit on slot spacing for efficient cell performance.

Zook, J. D.↗
NASA NTRS2002

Motion of Drops on Surfaces with Wettability Gradients

A liquid drop present on a solid surface can move because of a gradient in wettability along the surface, as manifested by a gradient in the contact angle. The contact angle at a given point on the contact line between a solid and a liquid in a gaseous medium is the angle between the tangent planes to the liquid and the solid surfaces at that point and is measured within the liquid side, by convention. The motion of the drop occurs in the direction of increasing wettability. The cause of the motion is the net force exerted on the drop by the solid surface because of the variation of the contact angle around the periphery. This force causes acceleration of an initially stationary drop, and leads to its motion in the direction of decreasing contact angle. The nature of the motion is determined by the balance between the motivating force and the resisting hydrodynamic force from the solid surface and the surrounding gaseous medium. A wettability gradient can be chemically induced as shown by Chaudhury and Whitesides who provided unambiguous experimental evidence that drops can move in such gradients. The phenomenon can be important in heat transfer applications in low gravity, such as when condensation occurs on a surface. Daniel et al have demonstrated that the velocity of a drop on a surface due to a wettability gradient in the presence of condensation can be more than two orders of magnitude larger than that observed in the absence of condensation. In the present research program, we have begun to study the motion of a drop in a wettability gradient systematically using a model system. Our initial efforts will be restricted to a system in which no condensation occurs. The experiments are performed as follows. First, a rectangular strip of approximate dimensions 10 x 20 mm is cut out of a silicon wafer. The strip is cleaned thoroughly and its surface is exposed to the vapor from an alkylchlorosilane for a period lasting between one and two minutes inside a desiccator. This is done using an approximate line source of the vapor in the form of a string soaked in the alkylchlorosilane. Ordinarily, many fluids, including water, wet the surface of silicon quite well. This means that the contact angle is small. But the silanized surface resists wetting, with contact angles that are as large as 100 degs. Therefore, a gradient of wettability is formed on the silicon surface. The region near the string is highly hydrophobic, and the contact angle decreases gradually toward a small value at the hydrophilic end away from this region. The change in wettability occurs over a distance of several mm. The strip is placed on a platform within a Plexiglas cell. Drops of a suitable liquid are introduced on top of the strip near the hydrophobic end. An optical system attached to a video camera is trained on the drop so that images of the moving drop can be captured on videotape for subsequent analysis. We have performed preliminary experiments with water as well as ethylene glycol drops. Results from these experiments will be presented in the poster. Future plans include the refinement of the experimental system so as to permit images to be recorded from the side as well as the top, and the conduct of a systematic study in which the drop size is varied over a good range. Experiments will be conducted with different fluids so as to obtain the largest possible range of suitably defined Reynolds and Capillary numbers. Also, an effort will be initiated on theoretical modeling of this motion. The challenges in the development of the theoretical description lie in the proper analysis of the region in the vicinity of the contact line, as well as in the free boundary nature of the problem. It is known that continuum models assuming the no slip condition all the way to the contact line fail by predicting that the stress on the solid surface becomes singular as the contact line is approached. One approach for dealing with this issue has been to relax the no-slip boundary condition using the Navier model. Molecular dynamics simulations of the contact line region show that for a non-polar liquid on a solid surface, the no-slip boundary condition is in fact incorrect near the contact line. Furthermore, the same simulations also show that the usual relationship between stress and the rate of deformation breaks down in the vicinity of the contact line. In developing continuum theoretical models of the system, we shall accommodate this knowledge to the extent possible.

Subramanian, R. Shankar↗
DOE OSTI2023

Highly-Conductive and Durable SOFC Cathode-Side Contact Based on Reactively-Sintered Mn-Co Spinel

A cathode-side contact layer with well-matched coefficient of thermal expansion is needed to prevent cracking of solid oxide fuel cell stacks from thermal cycling during stack operations. An Mn 1.25 Co 1.75 O 4 (MCO) spinel layer synthesized via reactive sintering with a metal-containing precursor was proposed as a highly conductive and durable contact material. Compared to the interconnect/contact/cathode assemblies with the (La 0.80 Sr 0.20 ) 0.95 MnO 3-x and La(Mn 0.45 Co 0.35 Cu 0.2 )O 3 contacts, the assembly with the MCO contact exhibited the lowest area-specific resistance at 800 °C (8.2 mΩ·cm 2 ) during 2000-h cyclic exposure and was crack-free based on the cross-sectional examination, indicative of the superiority of the spinel contact over the perovskite counterparts.

Electrochemistry↗
DOE OSTI2020

Conductive spinels derived from Co–Mn based alloy precursor for SOFC cathode-side contact application

The utilization of gas-atomized Co–Mn based alloy precursor is a promising approach to lowering the sintering temperature of the spinel contact layer and enhancing its performance. In this work, simulated interconnect/contact/cathode cells are employed to investigate the effects of different metallic precursors (i.e., three Co–Mn based alloy powders and a mixture of Co + MnO 2 powders) on the microstructure and performance of the reactively-sintered MnCo 2 O 4 -based contact layer. While excellent overall electrical performance is observed for all the cells with the four contact precursors during 1000-h testing at 800 °C in air, the cell with the Ce-doped alloy contact precursor shows the lowest cell area specific resistance (ASR) and ASR degradation rate. Cross-sectional observation of the tested cells is conducted to assess the compatibility of the contact layer with adjacent components as well as its effectiveness in reducing the Cr 2 O 3 scale growth and blocking Cr migration from the interconnect to the cathode.

08 HYDROGEN↗
DOE OSTI2021

Post weld heat treatment and operating temperature effect on tribological behavior of laser cladded stellite 21 coating

This study intends to investigate the feasibility of using laser cladding as a potential process to repair hot working tools by a hardfacing process. A Stellite 21 alloy coating was printed on a 350 maraging steel via laser cladding and the coating microstructure and tribological performance were characterized in as printed conditions and after heat treatment. Such a laser-processed coating showed a high integrity with little porosity and good bonding with the substrate. The Stellite coating produced substantially lower friction and a smoother contact area but had inferior wear resistance compared with the maraging steel substrate. Post process heat treatment at 650 °C for 20 h led to significant amount of strain-induced FCC to HCP phase transformation but had little improvement in wear resistance. Detailed materials characterization using X-ray diffraction and electron microscopy provided fundamental insights to the underlying mechanisms. This study opens the door for future R&D for tool surface repair by laser cladding.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Metallicity of 2H-MoS 2 induced by Au hybridization

Recent studies have shown that MoS 2 can undergo a structural phase transition from the 2H to 1T' phase on Au substrates at moderate temperatures. In this study, we use ultraviolet and x-ray photoelectron spectroscopy, Raman and photoluminescence spectroscopy, and scanning tunneling microscopy/spectroscopy to probe the impact of annealing exfoliated, monolayer MoS 2 on Au. Our results across multiple length scales indicate that 2H-MoS 2 becomes hybridized with Au upon thermal annealing without inducing the 1T' structural phase and the bandgap can be modulated to zero width depending on the degree of hybridization. These results can be used to control the resistance of metal-MoS 2 contacts at the atomic scale without introduction of defects or structural phase transitions and are important for devices such as memristors.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Direct Metallization with Reactive Inks – Assessment of Reliability and Process Sensitivities

This project will reduce silver consumption in photovoltaic cells by a factor of almost ten – from 95 mg/cell (the median across technologies) to 10 mg/cell. To achieve this goal, we will replace screen-printed silver pastes with contact dispensed reactive inks that produce lower resistivity metallizations at lower temperatures and with thinner films. This project will generate the understanding necessary to scale this reactive ink technology from the bench-scale to commercial throughputs. Specifically, it will combine fundamental understanding on physics and chemistries involved in contact printing of reactive inks with detailed performance and reliability studies to quantify how tightly processing parameters need to be controlled in order to reliably metallize high efficiency solar cells at commercial throughputs of 36,000 cells/hour.

14 SOLAR ENERGY↗
DOE OSTI2023

High figure of merit extreme bandgap Al 0.87 Ga 0.13 N-Al 0.64 Ga 0.36 N heterostructures over bulk AlN substrates

We report on high-quality n -Al 0.87 Ga 0.13 N-A 0.64 Ga 0.36 N heterostructures over single crystal AlN. For these pseudomorphic heterostructures, high-resolution X-ray and X-ray Topographic analysis was used to establish a threading dislocation density of 7 × 10 3 cm -2 . Using reverse composition graded n + -Al x Ga 1- x N contact layers, we obtained linear ohmic contacts with 4.3 Ω mm specific resistance. A critical breakdown field >11 MV cm -1 was also measured. In combination with the channel resistance of 2400 Ω sq -1 , these translate to a Baliga’s Figure of Merit of 2.27 GW cm -2 . This, to the best of our knowledge is the highest reported value for extreme bandgap AlGaN heterostructures.

42 ENGINEERING↗
NASA NTRS1975

ATS-6 - Solar cell flight experiment after 325 days in synchronous orbit

Preliminary results of the Applications Technology Satellite-6 (ATS-6) solar cell flight experiment to isolate and identify solar cell degradation mechanisms resulting from particulate radiation and to obtain specific design data applicable to extended synchronous spacecraft missions are presented. The experiment includes 80 individual cells representing 16 different solar cell/cover glass configurations. Most of the cells are 0.030 cm thick boron doped n/p cells with 10 ohm cm resistivity and solder-coated AgTi contacts. The voltage-current characteristics were measured regularly. The data for the first 325 days of flight show short circuit currents 1-8% higher than measurements made with solar simulations. Maximum power varied between -1 and +6%. After 50 days in orbit the degradation of short circuit current due to ultraviolet effects was determined to be about 2%. All cells except those with fluorinated ethylene propylene covers performed well after 325 days.

Goldhammer, L. J.↗
NASA NTRS1990

New Materials And Treatments For Turbopump Bearings

Report evaluates materials and surface treatments for bearings for liquid-oxygen turbopumps. Key properties sought for application are low friction, low wear, and resistance to corrosion and rolling-contact fatigue.

Wedeven, L. D.↗
NASA NTRS1990

The experimental evaluation and application of high-temperature solid lubricants

A research program is described which developes an understanding of high-temperature solid lubrication and experimental techniques through the development of a composite lubricant coating system. The knowledge gained through this research was then applied to a specific engineering challenge, the tribology of a sliding seal for hypersonic flight vehicles. The solid lubricant coating is a chromium carbide based composite combined with silver, which acts as a low temperature lubricant, and barium fluoride/calcium fluoride eutectic, which acts as a high-temperature lubricant. This composite coating provides good wear resistance and low friction for sliding contacts from room temperature to over 900 C in reducing or oxidative environments. The specific research on this coating included a composition screening using a foil gas bearing test rig and the use of thin silver films to reduce initial wear using a pin-on-disk test rig. The chemical stability of the materials used was also addressed. This research indicated that soft metallic films and materials which become soft at elevated temperatures are potentially good lubricants. The general results from the experiments with the model solid lubricant coating were then applied to a sliding seal design concept. This seal design requires that a braided ceramic fabric slide against a variety of metal counterface materials at temperatures from 25 to 850 C in an oxidative environment. A pin-on-disk tribometer was used to evaluate the tribological properties of these materials and to develop lubrication techniques. The results indicate that these seal materials must be lubricated to prevent wear and reduce friction. Thin films of silver, gold and calcium fluoride provided lubrication to the sliding materials.

Dellacorte, Christopher↗