Results for “CFD modeling” — Page 34

NASA NTRSDate not supplied

Multiscale Mesh Adaptation for Transonic Aeroelastic Flutter Problems

This work applies multiscale mesh adaptation with refine to reduce spatial discretization error of aeroelastic computational fluid dynamics (CFD) simulations. Benchmark flutter models, such as the pitch and plunge NACA64A-010 airfoil and the benchmark supercritical wing, are studied with both a linearized frequency-domain solver and time-marching CFD coupled to a modal structural solver in FUN3D. The undeformed NASA Common Research Model (CRM), an aeroelastic jig shape variant of the CRM, is also studied with the linearized frequency-domain approach. For these cases, the adaptation process converges to comparable flutter predictions to hand-generated meshes but with smaller node counts. However the additional disciplines of the linearized frequency-domain analysis, the mesh deformation, and the unsteady finite-volume solver create robustness challenges that need to be addressed before it can be applied as a fully automated process for complex transonic aeroelastic problems. In particular, negative volumes are observed to be an issue for FUN3D’s linear elasticity mesh deformation solver when moving the adapted meshes.

Aeroelasticity↗

NASA NTRS2023

Measurements and Computations of the Turbulent Corner Flow on the NASA Juncture-Flow Model with a Symmetric Wing

The NASA Juncture Flow experiment is designed to acquire high-quality flowfield data deep in the corner of a wing-fuselage junction specifically for the purpose of computational fluid dynamics (CFD) validation and turbulence model improvement. This paper will present and discuss the results of a recent experiment with the juncture-flow model in the NASA Langley 14- by 22-Foot Subsonic Tunnel. The main objective of that test was to expand the existing juncture-flow dataset with a symmetric wing case that displays fully attached, incipient separation, and separated flow in the corner of the wing-fuselage junction, depending on the model pitch angle. Laser Doppler velocimetry (LDV) measurements were made at three model pitch angles (0 deg: fully attached, 1 deg: incipient separation, and 5 deg: separated flow) and for each one, mean-flow and Reynolds-stress data was obtained on the fuselage and at several streamwise locations along the corner of the wing-fuselage junction. Supporting measurements were made during the test campaign and included model and tunnel wall static pressures, tunnel wall and ceiling boundary-layer rake data, oil-flow visualizations, and laser-based measurements of the as-built model geometry and model position in the test section. Comparisons between the experimental data and Reynolds averaged Navier-Stokes CFD results will also be presented and discussed.

Juncture Flow↗

NASA NTRSDate not supplied

Measurements and Computations of the Turbulent Corner Flow on the NASA Juncture-Flow Model with a Symmetric Wing

The NASA Juncture Flow experiment is designed to acquire high-quality flowfield data deep in the corner of a wing-fuselage junction specifically for the purpose of computational fluid dynamics (CFD) validation and turbulence model improvement. This paper will present and discuss the results of a recent experiment with the juncture-flow model in the NASA Langley 14- by 22-Foot Subsonic Tunnel. The main objective of that test was to expand the existing juncture-flow dataset with a symmetric wing case that displays fully attached, incipient separation, and separated flow in the corner of the wing-fuselage junction, depending on the model pitch angle. Laser Doppler velocimetry (LDV) measurements were made at three model pitch angles (0 deg: fully attached, 1 deg: incipient separation, and 5 deg: separated flow) and for each one, mean-flow and Reynolds-stress data was obtained on the fuselage and at several streamwise locations along the corner of the wing-fuselage junction. Supporting measurements were made during the test campaign and included model and tunnel wall static pressures, tunnel wall and ceiling boundary-layer rake data, oil-flow visualizations, and laser-based measurements of the as-built model geometry and model position in the test section. Comparisons between the experimental data and Reynolds averaged Navier-Stokes CFD results will also be presented and discussed.

Juncture Flow↗

NASA NTRS2013

Computational Study of the CC3 Impeller and Vaneless Diffuser Experiment

Centrifugal compressors are compatible with the low exit corrected flows found in the high pressure compressor of turboshaft engines and may play an increasing role in turbofan engines as engine overall pressure ratios increase. Centrifugal compressor stages are difficult to model accurately with RANS CFD solvers. A computational study of the CC3 centrifugal impeller in its vaneless diffuser configuration was undertaken as part of an effort to understand potential causes of RANS CFD mis-prediction in these types of geometries. Three steady, periodic cases of the impeller and diffuser were modeled using the TURBO Parallel Version 4 code: 1) a k-epsilon turbulence model computation on a 6.8 million point grid using wall functions, 2) a k-epsilon turbulence model computation on a 14 million point grid integrating to the wall, and 3) a k-omega turbulence model computation on the 14 million point grid integrating to the wall. It was found that all three cases compared favorably to data from inlet to impeller trailing edge, but the k-epsilon and k-omega computations had disparate results beyond the trailing edge and into the vaneless diffuser. A large region of reversed flow was observed in the k-epsilon computations which extended from 70% to 100% span at the exit rating plane, whereas the k-omega computation had reversed flow from 95% to 100% span. Compared to experimental data at near-peak-efficiency, the reversed flow region in the k-epsilon case resulted in an under-prediction in adiabatic efficiency of 8.3 points, whereas the k-omega case was 1.2 points lower in efficiency.

Kulkarni, Sameer↗

NASA NTRS2013

Computational Study of the CC3 Impeller and Vaneless Diffuser Experiment

Centrifugal compressors are compatible with the low exit corrected flows found in the high pressure compressor of turboshaft engines and may play an increasing role in turbofan engines as engine overall pressure ratios increase. Centrifugal compressor stages are difficult to model accurately with RANS CFD solvers. A computational study of the CC3 centrifugal impeller in its vaneless diffuser configuration was undertaken as part of an effort to understand potential causes of RANS CFD mis-prediction in these types of geometries. Three steady, periodic cases of the impeller and diffuser were modeled using the TURBO Parallel Version 4 code: (1) a k-ε turbulence model computation on a 6.8 million point grid using wall functions, (2) a k-ε turbulence model computation on a 14 million point grid integrating to the wall, and (3) a k-ω turbulence model computation on the 14 million point grid integrating to the wall. It was found that all three cases compared favorably to data from inlet to impeller trailing edge, but the k-ε and k-ω computations had disparate results beyond the trailing edge and into the vaneless diffuser. A large region of reversed flow was observed in the k-ε computations which extended from 70 to 100 percent span at the exit rating plane, whereas the k-ω computation had reversed flow from 95 to 100 percent span. Compared to experimental data at near-peak-efficiency, the reversed flow region in the k-ε case resulted in an underprediction in adiabatic efficiency of 8.3 points, whereas the k-ω case was 1.2 points lower in efficiency.

Kulkarni, Sameer↗

NASA NTRS1995

Turbulence modeling for non-equilibrium flow

The work performed during this year has involved further assessment and extension of the k-epsilon-v(exp 2) model, and initiation of work on scalar transport. The latter is introduced by the contribution of Y. Shabany to this volume. Flexible, computationally tractable models are needed for engineering CFD. As computational technology has progressed, the ability and need to use elaborate turbulence closure models has increased. The objective of our work is to explore and develop new analytical frameworks that might extend the applicability of the modeling techniques. In past years the development of a method for near-wall modeling was described. The method has been implemented into a CFD code and its viability has been demonstrated by various test cases. Further tests are reported herein. Non-equilibrium near-wall models are needed for some heat transfer applications. Scalar transport seems generally to be more sensitive to non-equilibrium effects than is momentum transport. For some applications turbulence anisotropy plays a role and an estimate of the full Reynolds stress tensor is needed. We have begun work on scalar transport per se, but in this brief I will only report on an extension of the k-epsilon-v(exp 2) model to predict the Reynolds stress tensor.

Durbin, P. A.↗

NASA NTRSDate not supplied

Validation of Two-Phase Flow Modeling Techniques in Loci-Stream Using Axial Jet Pressure Control and Autogenous Pressurization Experiments

Improvements to computational fluid dynamics modeling of cryogenic fluid management operations are presented with experimental validations. Modeling improvements includes utilizing improved delayed detaches eddy simulation to more effectively model turbulence compared to the Reynolds-averaged Navier Stokes modeling, modeling temperature dependent tank solid properties to capture large variation in thermodynamic properties at cryogenic conditions, modeling real gas equation of state for hydrogen instead of ideal gas behavior, and an on-going effort to improve interface turbulence transport for the volume of fluid method. Two flight-scale ground tests, five K-site tank axial jet pressure control experiments and an Engineering Design Unit tank autogenous pressurization experiment are validated and show the effectiveness of the improved modeling techniques. The successful validation establishes further trust in these models for flight project support and provides a pathway for maturation of in-development interface turbulence damping model for the volume of fluid method for more generalized applications.

CFD↗

NASA NTRS1994

Computational Methods for HSCT-Inlet Controls/CFD Interdisciplinary Research

A program aimed at facilitating the use of computational fluid dynamics (CFD) simulations by the controls discipline is presented. The objective is to reduce the development time and cost for propulsion system controls by using CFD simulations to obtain high-fidelity system models for control design and as numerical test beds for control system testing and validation. An interdisciplinary team has been formed to develop analytical and computational tools in three discipline areas: controls, CFD, and computational technology. The controls effort has focused on specifying requirements for an interface between the controls specialist and CFD simulations and a new method for extracting linear, reduced-order control models from CFD simulations. Existing CFD codes are being modified to permit time accurate execution and provide realistic boundary conditions for controls studies. Parallel processing and distributed computing techniques, along with existing system integration software, are being used to reduce CFD execution times and to support the development of an integrated analysis/design system. This paper describes: the initial application for the technology being developed, the high speed civil transport (HSCT) inlet control problem; activities being pursued in each discipline area; and a prototype analysis/design system in place for interactive operation and visualization of a time-accurate HSCT-inlet simulation.

Cole, Gary L.↗

NASA NTRSDate not supplied

Measurements and Computations of the Turbulent Corner Flow on the NASA Juncture-Flow Model with a Symmetric Wing

The NASA Juncture Flow experiment is designed to acquire high-quality flowfield data deep in the corner of a wing-fuselage junction specifically for the purpose of computational fluid dynamics (CFD) validation and turbulence model improvement. This paper presents and discusses the results of a recent experiment with the juncture-flow model in the NASA Langley 14- by 22-Foot Subsonic Tunnel. The main objective of the test was to expand the existing juncture-flow dataset with a symmetric wing case that displays fully attached, incipient separation, and separated flow in the corner of the wing-fuselage junction, depending on the model angle of incidence. Laser Doppler velocimetry (LDV) measurements were made at three model angles of incidence (0 deg: fully attached, 1 deg: incipient separation, and 5 deg: separated flow) and for each one, mean-flow and Reynolds-stress data were obtained on the fuselage and at several streamwise locations along the corner of the wing-fuselage junction. Supporting measurements were made during the test campaign and included model and tunnel wall static pressures, tunnel wall and ceiling boundary-layer rake data, oil-flow visualizations, and laser-based measurements of the as-built model geometry and model position in the test section. Comparisons between the experimental data on the test article and Reynolds-averaged Navier-Stokes CFD results are presented and discussed.

Juncture Flow↗

NASA NTRS2016

Computational Evaluation of Inlet Distortion on an Ejector Powered Hybrid Wing Body at Takeoff and Landing Conditions

Due to the aft, upper surface engine location on the Hybrid Wing Body (HWB) planform, there is potential to shed vorticity and separated wakes into the engine when the vehicle is operated at off-design conditions and corners of the envelope required for engine and airplane certification. CFD simulations were performed of the full-scale reference propulsion system, operating at a range of inlet flow rates, flight speeds, altitudes, angles of attack, and angles of sideslip to identify the conditions which produce the largest distortion and lowest pressure recovery. Pretest CFD was performed by NASA and Boeing, using multiple CFD codes, with various turbulence models. These data were used to make decisions regarding model integration, characterize inlet flow distortion patterns, and help define the wind tunnel test matrix. CFD was also performed post-test; when compared with test data, it was possible to make comparisons between measured model-scale and predicted full-scale distortion levels. This paper summarizes these CFD analyses.

Wind Tunnel Testing↗

NASA NTRSDate not supplied

Validation of Two-phase Flow Modeling Techniques in Loci-Stream using Axial Jet Pressure Control and Autogenous Pressurization Experiment

Improvements to computational fluid dynamics modeling of cryogenic fluid management operations are presented with experimental validations. Modeling improvements includes utilizing improved delayed detaches eddy simulation to more effectively model turbulence compared to the Reynolds-averaged Navier Stokes modeling, modeling temperature dependent tank solid properties to capture large variation in thermodynamic properties at cryogenic conditions, modeling real gas equation of state for hydrogen instead of ideal gas behavior, and an on-going effort to improve interface turbulence transport for the volume of fluid method. Two flight-scale ground tests, five K-site tank axial jet pressure control experiments and an Engineering Design Unit tank autogenous pressurization experiment are validated and show the effectiveness of the improved modeling techniques. The successful validation establishes further trust in these models for flight project support and provides a pathway for maturation of in-development interface turbulence damping model for the volume of fluid method for more generalized applications.

CFD↗

NASA NTRSDate not supplied

Transition prediction in hypersonic regime on complex geometries with RANS-based models

In the near future, RANS computations will continue to play a significant role in the design of hypersonic vehicles with complex geometries. Therefore, it is imperative to continue testing, benchmarking, and refining the RANS models. In the present study, we evaluate RANS-like, transport equations-based models for predicting laminar-turbulent transition over a full-scale scale model of the BOLT flight configuration that was tested in the CUBRC LENS-II wind tunnel test facility. Based on the availability of the experimental results, comparisons are made between computations from several pre-existing transition models and Computational Fluid Dynamics (CFD) codes, with an emphasis on using the same computational meshes and flow conditions for all computations. The analysis covers the sensitivity of the transition predictions to the input parameters for five different transition models (four mainstream models designed for low-speed flows and a uniquely high-speed model), grid resolution, and the details of model implementation across three different flow solvers. The results show that the phenomenological models can describe significant aspects of the measured transition front. However, a number of additional improvements are required before these models can offer more reliable estimates of transition in high-speed flows.

CFD↗

NASA NTRSDate not supplied

Transition Prediction in Hypersonic Regime on Complex Geometries With Rans-Based Models

In the near future, RANS computations will continue to play a significant role in the design of hypersonic vehicles with complex geometries. Therefore, it is imperative to continue testing, benchmarking, and refining the RANS models. In the present study, we evaluate RANS-like, transport equations-based models for predicting laminar-turbulent transition over a full-scale scale model of the BOLT flight configuration that was tested in the CUBRC LENS-II wind tunnel test facility. Based on the availability of the experimental results, comparisons are made between computations from several pre-existing transition models and Computational Fluid Dynamics (CFD) codes, with an emphasis on using the same computational meshes and flow conditions for all computations. The analysis covers the sensitivity of the transition predictions to the input parameters for five different transition models (four mainstream models designed for low-speed flows and a uniquely high-speed model), grid resolution, and the details of model implementation across three different flow solvers. The results show that the phenomenological models can describe significant aspects of the measured transition front. However, a number of additional improvements are required before these models can offer more reliable estimates of transition in high-speed flows.

CFD↗

NASA NTRS2022

Multi-Fidelity CFD Simulation of the Multirotor Test Bed

The high-fidelity and reduced order CFD method's validation and analysis are presented for the Multirotor Test Bed. The reduced-order method uses a rotor-disk model in the OVERFLOW CFD code and is an important aspect of this study. A rotor-trim option loosely coupling the Comprehensive code CAMRAD II with the OVERFLOW CFD code is included in the simulation that captures rotor blade aerodynamics, blade and rotor performance, rotor-rotor, and rotor-body interactions. Detailed comparison and validation were performed for both higher-fidelity full rotor unsteady flows and reduced-order rotor-disk methods. The tunnel geometry is included in the detailed computational effort. Computations of the low-Reynolds number flows were performed for a different number of in-plane rotors as well as for a single rotor modeled inside the tunnel.

ARMD↗

NASA NTRS2014

High-Lift OVERFLOW Analysis of the DLR-F11 Wind Tunnel Model

In response to the 2nd AIAA CFD High Lift Prediction Workshop, the DLR-F11 wind tunnel model is analyzed using the Reynolds-averaged Navier-Stokes flow solver OVERFLOW. A series of overset grids for a bracket-off landing configuration is constructed and analyzed as part of a general grid refinement study. This high Reynolds number (15.1 million) analysis is done at multiple angles-of-attack to evaluate grid resolution effects at operational lift levels as well as near stall. A quadratic constitutive relation recently added to OVERFLOW for improved solution accuracy is utilized for side-of-body separation issues at low angles-of-attack and outboard wing separation at stall angles. The outboard wing separation occurs when the slat brackets are added to the landing configuration and is a source of discrepancy between the predictions and experimental data. A detailed flow field analysis is performed at low Reynolds number (1.35 million) after pressure tube bundles are added to the bracket-on medium grid system with the intent of better understanding bracket/bundle wake interaction with the wing's boundary layer. Localized grid refinement behind each slat bracket and pressure tube bundle coupled with a time accurate analysis are exercised in an attempt to improve stall prediction capability. The results are inconclusive and suggest the simulation is missing a key element such as boundary layer transition. The computed lift curve is under-predicted through the linear range and over-predicted near stall, and the solution from the most complete configuration analyzed shows outboard wing separation occurring behind slat bracket 6 where the experiment shows it behind bracket 5. These results are consistent with most other participants of this workshop.

High-lift↗

NASA NTRS2018

Performance of Supersonic Parachutes Behind Slender Bodies

NASA’s ASPIRE (Advanced Supersonic Parachute Inflation Research Experiments) project is investigating the supersonic deployment, inflation and aerodynamics of full-scale disk-gap-band (DGB) parachutes. The first two flight tests were carried out in October 2017 and March 2018, while a third test is planned for the fall of 2018. In these tests, Mars-relevant conditions are achieved by deploying the parachutes at high altitudes over Earth using a sounding rocket test platform. As a result, the parachute is deployed behind a slender body (roughly 1/6-th the diameter of the capsule that will use this parachute for descent at Mars). Because there is limited flight and experimental data for supersonic DGBs behind slender bodies, the development of the parachute aerodynamic models was informed by CFD simulations of both the leading body wake and the parachute canopy. This presentation will describe the development of the pre-flight parachute aerodynamic models and compare pre-flight predictions with the reconstructed performance of the parachute during the flight tests. Specific attention will be paid to the differences in parachute performance behind blunt and slender bodies.

CFD↗

NASA NTRS2011

More-Accurate Model of Flows in Rocket Injectors

An improved computational model for simulating flows in liquid-propellant injectors in rocket engines has been developed. Models like this one are needed for predicting fluxes of heat in, and performances of, the engines. An important part of predicting performance is predicting fluctuations of temperature, fluctuations of concentrations of chemical species, and effects of turbulence on diffusion of heat and chemical species. Customarily, diffusion effects are represented by parameters known in the art as the Prandtl and Schmidt numbers. Prior formulations include ad hoc assumptions of constant values of these parameters, but these assumptions and, hence, the formulations, are inaccurate for complex flows. In the improved model, these parameters are neither constant nor specified in advance: instead, they are variables obtained as part of the solution. Consequently, this model represents the effects of turbulence on diffusion of heat and chemical species more accurately than prior formulations do, and may enable more-accurate prediction of mixing and flows of heat in rocket-engine combustion chambers. The model has been implemented within CRUNCH CFD, a proprietary computational fluid dynamics (CFD) computer program, and has been tested within that program. The model could also be implemented within other CFD programs.

Hosangadi, Ashvin↗

NASA NTRS2015

Assessment of Geometry and In-Flow Effects on Contra-Rotating Open Rotor Broadband Noise Predictions

Application of previously formulated semi-analytical models for the prediction of broadband noise due to turbulent rotor wake interactions and rotor blade trailing edges is performed on the historical baseline F31/A31 contra-rotating open rotor configuration. Simplified two-dimensional blade element analysis is performed on cambered NACA 4-digit airfoil profiles, which are meant to serve as substitutes for the actual rotor blade sectional geometries. Rotor in-flow effects such as induced axial and tangential velocities are incorporated into the noise prediction models based on supporting computational fluid dynamics (CFD) results and simplified in-flow velocity models. Emphasis is placed on the development of simplified rotor in-flow models for the purpose of performing accurate noise predictions independent of CFD information. The broadband predictions are found to compare favorably with experimental acoustic results.

Zawodny, Nikolas S.↗