Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Low cycle fatigue behavior of AlSi10Mg(Cu) alloy at high temperature

Highlights: • The cyclic stress response of AlSi10Mg(Cu) alloy in LCF regime is temperature-dependent. • Precipitates transitions were observed after high temperature cycle loading. • Changes in the interaction mechanism between dislocations and nanoparticles lead to different cyclic stress responses. - Abstract: Low cycle fatigue (LCF) behavior of AlSi10Mg(Cu) alloy was investigated at 100 °C and 250 °C over a range of strain amplitude from 0.25% to 0.40%. Cycle stress response, hysteresis loops, fatigue life, as well as post-fatigue microstructure were studied in detail. Except 0.25%, the alloy performed cycle hardening behavior at 100 °C and softening behavior at 250 °C at any given strain amplitude, which corresponded well with the observed phenomena in hysteresis loops. At any given temperature, cyclic stress increases while fatigue life decreases with the increasing strain amplitude. The fatigue life of the studied alloy at 100 °C was higher than that at 250 °C under the same strain amplitude. Fractography indicated that most fatigue crack initiated from casting defects. The fatigue crack propagation was mainly characterized by fatigue striations and tear ridges in any conditions. Section inspection shows that the number of cracked eutectic Si increases with decreasing the temperature or increasing strain amplitude. Post-mortem transmission electron microscopy (TEM) investigations indicated that cyclic hardening behavior at 100 °C was due to the pinning effect of coherent precipitates (β″-Mg{sub 2}Si and GP zones). Most of tiny coherency precipitates and clusters transformed to large semi-coherency Q′ and β′-Mg{sub 2}Si precipitates after cyclic loading at 250 °C, leading to the sharp decrease of pinning number and dislocation density, which is a key reason for the cyclic softening. Another factor is that more dislocations can be activated and dislocation climb is easier at higher temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Structure and phase formation behavior and dielectric and magnetic properties of lead iron tantalate-lead zirconate titanate multiferroic ceramics

Highlights: • The multiferroic ceramics consisted of PFT and PZT. • Crystal structure changed from cubic to mixedcubic and tetragonal with increasing PZT content. • Dielectric showed the samples underwent a typical relaxor ferroelectric behavior. • Magnetic properties showed very interesting behavior with square saturated magnetic hysteresis loops. - Abstract: Multiferroic (1 − x)Pb(Fe{sub 0.5}Ta{sub 0.5})O{sub 3}–xPb(Zr{sub 0.53}Ti{sub 0.47})O{sub 3} (or PFT–PZT) ceramics were synthesized by solid-state reaction method. The crystal structure and phase formation of the ceramics were examined by X-ray diffraction (XRD). The local structure surrounding Fe and Ti absorbing atoms was investigated by synchrotron X-ray Absorption Near-Edge Structure (XANES) measurement. Dielectric properties were studied as a function of frequency and temperature using a LCR meter. A vibrating sample magnetometer (VSM) was used to determine the magnetic hysteresis loops. XRD study indicated that the crystal structure of the sample changed from pure cubic to mixed cubic and tetragonal with increasing PZT content. XANES measurements showed that the local structure surrounding Fe and Ti ions was similar. Dielectric study showed that the samples underwent a typical relaxor ferroelectric behavior while the magnetic properties showed very interesting behavior with square saturated magnetic hysteresis loops.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Self-regulating behavior of hybrid membrane systems as demonstrated in an element-scale forward osmosis-reverse osmosis hybrid system

Hybrid membrane systems can be difficult to design due to the requisite flow rate matching between up- and downstream unit operations. In this work, we use a forward osmosis-reverse osmosis (FO-RO) hybrid system to demonstrate how some membrane systems can exhibit self-regulating behavior due to osmotic coupling. This can reduce the need for complex control systems for flow balancing. We show this behavior using a module-scale test bed that can mimic the behavior of larger scale operations. The system shows permeate flow rate near-convergence between the FO and RO modules after startup or when perturbed by a change in RO module pressure. The behavior of this hybrid system demonstrates that some membrane operations can exploit osmotic interdependence, rather than expensive control systems, to achieve steady state operation.

Debottlenecking↗
DOE OSTI2022

A layered 2D computational framework: Theory and applications to nuclear fuel behavior

Nuclear fuel performance computer codes have been developed over the last 50 years to analyze fuel behavior under various operating conditions. Traditionally, these codes used quasi-two-dimensional (also commonly known as 1.5D) representations of the fuel rod, which model the rod using a set of one-dimensional axisymmetric models that represent the behavior at specific axial positions on the rod. Modern fuel performance codes have the ability to investigate full three-dimensional (3D) effects and couple to other physics-based codes for true multiphysics simulations. However, with increasing complexity comes increasing computational costs. Many phenomena of interest involve azimuthally-varying behavior that cannot be represented using the aforementioned quasi-two-dimensional approach, but do not require the use of a full 3D model. To efficiently address these problems, there is a need for a computational framework that provides a compromise between the quasi-two-dimensional and full 3D models. In this paper, we present a new quasi-three-dimensional approach that represents the fuel as a set of 2D planar models that represent the behavior of the fuel cross-section at various axial positions. Presented here are the theory behind the methodology, test cases to illustrate proper implementation, and practical applications of its use in the BISON fuel performance code for a variety of cases in nuclear fuel analysis, such as fuel fracture, axial fuel relocation, and cladding distension and oxidation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

A review of rare earth elements and yttrium in coal ash: Content, modes of occurrences, combustion behavior, and extraction methods

Rare earth elements and yttrium (REY) have attracted considerable attention over the last decade because of their vital roles in clean energy, consumer product, national defense and security applications, among other uses. Due to the retention of REY during coal burning, coal combustion ash is considered as potential alternative sources for REY. Understanding the content, speciation, retention and/or transformation behavior of REY during coal combustion not only expands our knowledge of the combustion behavior of the trace elements in coal, but also provides basis for modeling REY partitioning during coal combustion and for developing economically viable REY recovery technologies. This review makes a critical summary of recent progress in the study of REY in coal ash. The contents and the extraction potentials of REY in coal ash derived from 15 major coal-producing countries worldwide were summarized and evaluated. Various analytical methods for determining REY bulk contents and speciation, together with the solid sample pretreatment, analytical accuracy and precision, advantages and disadvantages were summarized and compared. Modern analytical approaches combined indirect methods (e.g., sequential extraction) shed light on the physical distribution, mineralogy, and the chemical state of REY in coal ash. Three types of REY occurrences in coal ash, including Si-Al glassy association, discrete minerals or compounds, and organic association (bound with unburned carbon) were defined in the review. The glassy association can be further divided into REY minerals closely bound to glass phases and dispersed throughout the glassy structure. REY partitioning in various emission streams, the size distribution, and their enrichment behavior in coal ash were discussed. Additionally, thermal behavior and transformation of various REY forms in coal during combustion process, including organic-associated REY, REY phosphates, REY carbonates, clay-bound REY and among others were summarized. Two possible retention mechanisms of REY by aluminosilicate glass at boiler temperature were proposed: the incorporation of the individual REY phases into the glass as inclusions and the diffusion of REY phases throughout Si-Al glass structures in the melting process. Feed coal mineral types, mineral-mineral associations, boiler conditions, and other factors control the retention process. After coal combustion, the speciation of REY in fly ash may be modified by the reactions of REY phases with flue gas components. Further, an overview of REY transformation mechanisms during coal combustion was deeply discussed. Finally, current extraction techniques for REY recovery from coal combustion ash were introduced. Future outlooks and research problems were also identified.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Relationships between maternally-transferred mercury and hatchling development, behavior, and survival in the American alligator ( Alligator mississippiensis )

Mercury is a toxic and pervasive environmental contaminant that can be transferred from mother to offspring during development. Consequences of maternally-transferred mercury have been observed in vertebrate taxa, including reduced clutch viability, reduced offspring size, and behavioral alterations. These sublethal effects have been assumed to decrease survivorship, though this is seldom assessed. Here, we examined how maternally-transferred mercury interacts with incubation temperature to influence reproductive success, offspring behavior, and subsequent survival in the American alligator (Alligator mississippiensis). We collected nine clutches of eggs from a mercury contaminated reservoir on the Savannah River Site, South Carolina, and incubated eggs at either female- or male-promoting temperatures. Clutch-averaged mercury in egg yolk was high relative to other studies in crocodilians and ranged from 0.248 to 0.554 ppm compared to 0.018–0.052 ppm at a site with low levels of mercury contamination; mercury levels in hatchling blood ranged from 0.090 to 0.490 ppm ($\overline{x}$= 0.240 ppm, n = 158). We found few, mostly negligible correlations between life history traits and mercury but noted a positive relationship with egg mass, possibly mediated by correlated maternal effects such as resource provisioning. Incubation temperature exerted strong effects on hatchling phenotypes, with warmer, male-promoting temperatures producing larger and bolder hatchlings. Presumptive females, produced from cooler incubation temperatures, spent more time in warm areas during behavior trials. Hatchlings were released 10–15 days post-hatch and surveyed over eight months to assess survival. Survivorship was positively correlated with hatchling size and negatively correlated with proportional time spent in warm areas. Presumptive females had much lower survival, and overall survivorship for the eight-month period was 0.185–0.208, depending on the modelling approach. Finally, our study suggests that, within the range of concentrations we observed, incubation temperature has a stronger effect on offspring behavior and survival than maternally-transferred mercury pollution in American alligators.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2017

Morphological and behavioral responses of zebrafish after 24 h of ketamine embryonic exposure

Ketamine, one anesthetic used as an illicit drug, has been detected both in freshwater and marine ecosystems. However, knowledge of its impact on aquatic life is still limited. This study aimed to test its effects in zebrafish embryos by analyzing its time- and dose-dependent developmental toxicity and long-term behavioral changes. The 24 h-LC{sub 50} was calculated from percent survival using probit analysis. Based on the 24 h-LC{sub 50} (94.4 mg L{sup −1}), embryos (2 hour post-fertilization - hpf) were divided into four groups, including control, and exposed for 24 h to ketamine concentrations of 50, 70 or 90 mg L{sup −1}. Developmental parameters were evaluated on the course of the experimental period, and anatomical abnormalities and locomotor deficits were analyzed at 144 hpf. Although the portion of ketamine transferred into the embryo was higher in the lowest exposed group (about 0.056 ± 0.020 pmol per embryo), the results showed that endpoints such as increased mortality, edema, heart rate alterations, malformation and abnormal growth rates were significantly affected. At 144 hpf, the developmental abnormalities included thoracic and trunk abnormalities in the groups exposed to 70 and 90 mg L{sup −1}. Defects in cartilage (alcian blue) and bone (calcein) elements also corroborated the craniofacial anomalies observed. A significant up-regulation of the development-related gene nog3 was detected by qRT-PCR at 8 hpf. Early exposure to ketamine also resulted in long-term behavioral changes, such as an increase in thigmotaxis and disruption of avoidance behavior at 144 hpf. Altogether, this study provides new evidence on the ketamine teratogenic potential, indicating a possible pharmacological impact of ketamine in aquatic environments. - Highlights: • 24 h exposure to ketamine increases mortality. • Morphological changes were observed after exposure. • Exposure to ketamine leads to severe craniofacial anomalies. • Developmental gene expression changes in response to ketamine. • Developmental ketamine exposure produces lasting behavioral changes.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2019

Evacuation decision behavior for no-notice emergency events

No-notice emergency events refer to unpredictable disasters such as earthquakes, chemical spills, or terrorist attacks, where it is impracticable to forewarn the public about their occurrence and design evacuation plans for them. This calls for an in-depth investigation of people’s evacuation behavior and identifying the most influential factors in their evacuation planning process to develop policy-sensitive pre-disaster plans for such events. As a response to this need, this study investigates individuals’ evacuation decision behavior in the context of no-notice emergency events. Since it is highly expected that people will have heterogenous decision behavior in such situations, we first apply a clustering algorithm to classify them into three maximally homogeneous clusters. Then, cluster-specific multivariate ordered probit models are developed to estimate the likelihood of selecting any of the three options of ignoring the situation, seeking shelter at the place, and evacuating to a safe place. The model estimation results indicate that a wide spectrum of factors affect the evacuation decision including individuals’ socio-economic attributes, disaster characteristics, built-environment factors, and government evacuation order. Further, variations of estimated coefficients across the population clusters highlight the significant dissimilarities in decision behavior of their associated members.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2011

Attitude towards littering as a mediator of the relationship between personality attributes and responsible environmental behavior

Highlights: > Independently, altruism and locus of control contributed significantly toward attitude towards littering. > Altruism and locus of control jointly contributed significantly to attitude towards littering. > The results further show a significant joint influence of altruism and locus of control on REB. > The independent contributions reveal that altruism and locus of control contribute significantly to REB. > Attitude towards littering mediates the relationship between locus of control and REB. - Abstract: The study tested whether attitude towards littering mediates the relationship between personality attributes (altruism and locus of control) and responsible environmental behavior (REB) among some residents of Ibadan metropolis, Nigeria. Using multistage sampling technique, measures of each construct were administered to 1360 participants. Results reveal significant independent and joint influence of personality attributes on attitude towards littering and responsible environmental behavior, respectively. Attitude towards littering also mediates the relationship between personality characteristics and REB. These findings imply that individuals who possess certain desirable personality characteristics and who have unfavorable attitude towards littering have more tendencies to engage in pro-environmental behavior. Therefore, stakeholders who have waste management as their priority should incorporate this information when guidelines for public education and litter prevention programs are being developed. It is suggested that psychologists should be involved in designing of litter prevention strategies. This will ensure the inclusion of behavioral issues in such strategies. An integrated approach to litter prevention that combines empowerment, cognitive, social, and technical solutions is recommended as the most effective tool of tackling the litter problem among residents of Ibadan metropolis.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Sliding friction and wear behavior of nuclear graphite in high temperature inert environment: Influence of contact load, speed and temperature

Repeated dynamic interactions of graphitic components in pebble-bed gas-cooled nuclear reactors can cause abrasive wear-induced pebble surface damage, generate hazardous fine graphite debris, and alter fuel circulation dynamics due to changes in friction behavior. Comprehensive tribological characterization of nuclear graphitic materials in conditions relevant to reactor operation is needed to assess reactor long-term safety and performance. This work reports sliding friction and wear behavior of self-mated nuclear graphite ET-10 at various elevated temperatures (650 °C and 750 °C), sliding speeds (1 and 10 mm/s) and contact loads (20 and 40 N) in a controlled argon environment. The results revealed nonmonotonic frictional behavior with a higher running-in coefficient of friction (COF) followed by a lower steady-state COF, as a result of transition from two-body abrasion to three-body abrasion along with formation of a tribofilm. A key finding of this work is the sensitivity of the running-in COF to experimental conditions; maximum running-in values were lower at either elevated temperature (0.52–0.54) or reduced sliding speed (0.51–0.54). Conversely, the steady-state COF remained invariant at approximately 0.3 across all tested parameters. Transmission electron microscopy revealed a 0.5–2.0 μm thick nanocrystalline tribofilm that was thought to be formed by the compaction of the graphitic wear debris on the contact surface during the sliding process. The nanocrystalline nature of the tribofilm was further confirmed by Raman spectroscopy. As a result, the combination of tribological testing and morphological characterization provided a mechanistic understanding of the frictional behavior of nuclear graphite upon sliding.

Friction↗
DOE OSTI2022

Emerging Electrochemical Techniques for Probing Site Behavior in Single-Atom Electrocatalysts

Single-atom catalysts (SACs) have aroused tremendous interest over the past decade, particularly in the community of energy and environment-related electrocatalysis. A rapidly growing number of recent publications have recognized it as a promising candidate with maximum atomic utilization, distinct activity, and selectivity in comparison to bulk catalysts and nanocatalysts. However, the complexity of localized coordination environments and the dispersion of isolated sites lead to significant difficulties when it comes to gaining insight into the intrinsic behavior of electrocatalytic reactions. Furthermore, the low metal loadings of most SACs make conventional ensemble measurements less likely to be accurate on the subnanoscale. Thus, it remains challenging to probe the activity and properties of individual atomic sites by available commercial instruments and analytical methods. In spite of this, continuing efforts have lately focused on the development of advanced measurement methodologies, which are very useful to the fundamental understanding of SACs. There have recently been a number of in situ/operando techniques applied to SACs, such as electron microscopy, spectroscopy, and other analysis methods, which support relevant functions to identify the active sites and reaction intermediates and to investigate the dynamic behavior of localized structures of the catalytic sites. This Account aims to present recent electrochemical probing techniques which can be used to identify single-atomic catalytic sites within solid supports. First, we describe the basic principles of molecular probe methods for the study and analysis of electrocatalytic site behavior. In particular, the in situ probing technique enabled by surface interrogation scanning electrochemical microscopy (SISECM) can measure the active site density and kinetic rate with high resolution. An alternative electrochemical probing technique is further demonstrated on the basis of single-entity electrochemistry, which allows the unique electrochemical imaging of the size and catalytic rate of single atoms, molecules, and clusters. Next, the merits and limitations of different electrochemical techniques are then discussed, along with perspectives for future prospects. Apart from this, we further showcase the powerful capability of emerging electrochemical probing techniques for determining significant effects and properties of SACs for various electrocatalytic reactions, including oxygen reduction and evolution, hydrogen evolution, and nitrate reduction. Overall, electrochemical techniques with atomic resolution have greatly increased opportunities for observing, measuring, and understanding the surface and interface chemistry during energy conversion. In the future, it is anticipated that the development of electrochemical probing techniques will be advanced with innovative perspectives on the behavior and features of SACs. We hope that this Account can contribute in several ways to promoting the fundamental knowledge and technical progress of emerging electrochemical measurements for studying SACs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Interfacial Phenomena and Mechanical Behavior of Polyetheretherketone/Polybenzimidazole Blend under Hygrothermal Environment

Demands for engineering applications of high performance polymers, such as the polyaryletherketone families, have grown significantly in recent years. Fundamental knowledge on the mechanical behavior of such polymers, especially under harsh environments, is still lacking. In this study, the mechanical behavior and interfacial phenomena of a blend of polybenzimidazole (PBI) particles having sizes of about 50 μm and polyetheretherketone (PEEK) matrix at 50:50 weight ratio was characterized. PBI and PEEK are known to be incompatible with each other in the dry state. The possible influence of hygrothermal exposure on interfacial bonding between PEEK and PBI has been systematically studied. Under dry conditions, the PEEK matrix dominates the dynamic mechanical behavior, indicating no noticeable viscoelastic coupling between the two phases. After being exposed to hygrothermal conditions, the T g of the PEEK phase in the blend shifts to a lower temperature by as much as 26 °C. The extent of this shift is much greater than what is observed for neat PEEK alone under the same condition. Nanomechanical property mapping results indicate that the interfacial region is broadened after 288 °C hot water immersion treatment. The above finding strongly suggests the hygrothermal conditioning promotes apparent compatibility between PEEK and PBI. Likewise, the fracture behavior of the blend provides direct evidence that the interfacial adhesion is greater than the cohesive strength of either phase after water immersion. In the meantime, it is found that both fracture toughness and tensile strength of the blend are improved by water absorption at 60 °C, at the expense of a minor reduction in Young’s modulus. However, if the blend is exposed to hot water at 288 °C, all of the mechanical properties will deteriorate significantly. In conclusion, the possible causes of the mechanical property deterioration in the PEEK/PBI blend after hygrothermal treatment are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanistic Study of Controlled Zinc Electrodeposition Behaviors Facilitated by Nanoscale Electrolyte Additives at the Electrode Interface

Nanoparticle organic hybrid materials (NOHMs) are liquid-like materials composed of an inorganic core to which a polymeric canopy is ionically tethered. NOHMs have unique properties including negligible vapor pressure, high oxidative thermal stability, and the ability to bind to reactive species of interest due to the tunability of their polymeric canopy. This makes them promising multifunctional materials for a wide range of energy and environmental technologies, including electrolyte additives for electrochemical energy storage (e.g., flow batteries) and the electrochemical conversion of CO 2 to chemicals and fuels. Due to their unique transport behaviors in fluid systems, an understanding of the near-electrode surface behavior of NOHMs in electrolyte solutions and their effect on electrochemical reactions is still lacking. In this work, the complexation of zinc (Zn) by NOHMs with an ionically tethered polyetheramine canopy (HPE) (NOHM-I-HPE) was studied using attenuated total reflectance Fourier transform infrared and Carbon-13 nuclear magnetic resonance spectroscopy. Additionally, various electrochemical techniques were employed to discern the role of NOHM-I-HPE during zinc electrodeposition, and the results were compared to those of the electrochemical system containing untethered HPE polymers. Our findings confirmed that NOHM-I-HPE and HPE reversibly complex zinc in the aqueous electrolyte. NOHM-I-HPE and HPE were found to block some of the electrode active sites, reducing the overall current density during electrodeposition, while facilitating the formation of smooth zinc deposits, as revealed by surface imaging and diffraction techniques. Observed variations in the current density responses and the degree of passivation created by the NOHM-I-HPE and HPE adsorbed on the electrode surface revealed that their different packing behaviors at the electrode–electrolyte interface influence the zinc deposition mechanism. The presence of the nanoparticle and ordering offered by the NOHMs as well as the structured conformation of the polymeric canopy allowed the formation of void spaces and free volumes for enhanced transport behaviors. Furthermore, these findings provided insights into how structured electrolyte additives such as NOHMs can allow for advancements in electrolyte design for controlled deposition of metal species from energy-dense electrolytes or for other electrochemical reactions.

25 ENERGY STORAGE↗
DOE OSTI2023

Microscopic Origins of the Nonlinear Behavior of Particle-Filled Rubber Probed with Dynamic Strain XPCS

The underlying microscopic response of filler networks in reinforced rubber to dynamic strain is not well understood due to the experimental difficulty of directly measuring filler network behavior in samples undergoing dynamic strain. This difficulty can be overcome with in situ X-ray photon correlation spectroscopy (XPCS) measurements. The contrast between the silica filler and the rubber matrix for X-ray scattering allows us to isolate the filler network behavior from the overall response of the rubber. This in situ XPCS technique probes the microscopic breakdown and reforming of the filler network structure, which are responsible for the nonlinear dependence of modulus on strain, known in the rubber science community as the Payne effect. These microscopic changes in the filler network structure have consequences for the macroscopic material performance, especially for the fuel efficiency of tire tread compounds. In this work, we elucidate the behavior with in situ dynamic strain XPCS experiments on industrially relevant, vulcanized rubbers filled (13 vol %) with novel air-milled silica of ultrahigh-surface area (UHSA) (250 m 2 /g). The addition of a silane coupling agent to rubber containing this silica causes an unexpected and counterintuitive increase in the Payne effect and decrease in energy dissipation. For this rubber, we observe a nearly two-fold enhancement of the storage modulus and virtually equivalent loss tangent compared to a rubber containing a coupling agent and conventional silica. Interpretation of our in situ XPCS results simultaneously with interpretation of traditional dynamic mechanical analysis (DMA) strain sweep experiments reveals that the debonding or yielding of bridged bound rubber layers is key to understanding the behavior of rubber formulations containing the silane coupling agent and high-surface area silica. These results demonstrate that the combination of XPCS and DMA is a powerful method for unraveling the microscale filler response to strain which dictates the dynamic mechanical properties of reinforced soft matter composites. With this combination of techniques, we have elucidated the great promise of UHSA silica when used in concert with a silane coupling agent in filled rubber. Such composites simultaneously exhibit large moduli and low hysteresis under dynamic strain.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Impact of Liquid-Vapor to Liquid-Liquid-Vapor Phase Transitions on Asphaltene-Rich Nanoaggregate Behavior in Athabasca Vacuum Residue + Pentane Mixtures

The bulk phase behavior of heavy oil + alkane mixtures and the behavior of the asphaltenes that they contain are topics of importance for the design and optimization of processes for petroleum production, transport, and refining and for performing routine saturates, aromatics, resins, and asphaltenes (SARA) analyses. In prior studies, partial phase diagrams and phase behavior models for Athabasca vacuum residue (AVR) comprising 32 wt % pentane asphaltenes + n-alkanes were reported. For mixtures with pentane, observed phase behaviors included single-phase liquid as well as liquid–liquid, liquid–liquid–vapor, and liquid–liquid–liquid–vapor regions. Dispersed solids were detected under some conditions as well but not quantified. In this work, small-angle X-ray scattering (SAXS) is used to study nanostructured materials in liquid phases present in AVR + n-pentane mixtures from 50 to 170 °C at mixture bubble pressure. The investigation focuses on the impact of the transition from a single AVR-rich liquid to co-existing pentane-rich and AVR-rich liquids on the nanostructure and the nanostructures most resistant to aggregation as the pentane composition axis is approached. Background scattering subtraction was performed using global mixture composition. The robustness of this assumption with respect to values obtained for coefficients appearing in a two level Beaucage unified equation fit is demonstrated. The nanostructured material is shown to arise at two length scales from 1 to 100 wt % AVR. Smaller nanostructures possess mean radii less than 50 Å, while the larger nanostructures possess mean radii greater than 250 Å. The addition of pentane to the AVR causes an increasingly large fraction of the large and small nanostructures to grow in size. Only nanostructures resistant to aggregation remain in the pentane-rich phase as the 0 wt % AVR axis is approached. Step changes in aggregation identified from changes in average radius of gyration, scattering coefficients, and surface/volume ratios arise at the liquid–vapor to liquid–liquid–vapor transition (~40 wt % pentane) and within the liquid–liquid–vapor region (~90 wt % pentane). The temperature is shown to have a limited effect on the mean size and structure of the nanostructured material present, irrespective of global composition.

Long, Bingwen↗
DOE OSTI2020

Crystallizing Atomic Xenon in a Flexible MOF to Probe and Understand Its Temperature-Dependent Breathing Behavior and Unusual Gas Adsorption Phenomenon

Flexible metal–organic frameworks (MOFs) hold great promise as smart materials for specific applications such as gas separation. These materials undergo interesting structural changes in response to guest molecules, which is often associated with unique adsorption behavior not possible for rigid MOFs. Understanding the dynamic behavior of flexible MOFs is crucial yet challenging as it involves weak host–guest interactions and subtle structural transformation not only at the atomic/molecular level but also in a nonsteady state. Here we report an in-depth study on the adsorbate- and temperature-dependent adsorption in a flexible MOF by crystallizing atomic gases into its pores. Mn(ina)2 shows an interesting temperature-dependent response toward noble gases. Its nonmonotonic, temperature-dependent adsorption profile results in an uptake maximum at a temperature threshold, a phenomenon that is unusual. Full characterization of Xe-loaded MOF structures is performed by in situ single-crystal and synchrotron X-ray diffraction, IR spectroscopy, and molecular modeling. The X-ray diffraction analysis offers a detailed explanation into the dynamic structural transformation and provides a convincing rationalization of the unique adsorption behavior at the molecular scale. The guest and temperature dependence of the structural breathing gives rise to an intriguing reverse of Xe/Kr adsorption selectivity as a function of temperature. The presented work may provide further understanding of the adsorption behavior of noble gases in flexible MOF structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Redox-switchable breathing behavior in tetrathiafulvalene-based metal–organic frameworks

Metal–organic frameworks (MOFs) that respond to external stimuli such as guest molecules, temperature, or redox conditions are highly desirable. Herein, we coupled redox-switchable properties with breathing behavior induced by guest molecules in a single framework. Guided by topology, two flexible isomeric MOFs, compounds 1 and 2, with a formula of In(Me 2 NH 2 ) (TTFTB), were constructed via a combination of [In(COO) 4 ]- metal nodes and tetratopic tetrathiafulvalene-based linkers (TTFTB). The two compounds show different breathing behaviors upon the introduction of N 2 . Single-crystal X-ray diffraction, accompanied by molecular simulations, reveals that the breathing mechanism of 1 involves the bending of metal–ligand bonds and the sliding of interpenetrated frameworks, while 2 undergoes simple distortion of linkers. Reversible oxidation and reduction of TTF moieties changes the linker flexibility, which in turn switches the breathing behavior of 2. The redox-switchable breathing behavior can potentially be applied to the design of stimuli-responsive MOFs.

carbon capture↗
DOE OSTI2017

Heavy fermion behavior in the quasi-one-dimensional Kondo lattice CeCo 2 Ga 8

Dimensionality plays an essential role in determining the anomalous non-Fermi liquid properties in heavy fermion systems. So far most heavy fermion compounds are quasi-two-dimensional or three-dimensional. Here we report the synthesis and systematic investigations of the single crystals of the quasi-one-dimensional Kondo lattice CeCo 2 Ga 8 . Resistivity measurements at ambient pressure reveal the onset of coherence at T * ≈ 20 K and non-Fermi liquid behavior with linear temperature dependence over a decade in temperature from 2 to 0.1 K. The specific heat increases logarithmically with lowering temperature between 10 and 2 K and reaches 800 mJ/mol K 2 at 1 K, suggesting that CeCo 2 Ga 8 is a heavy fermion compound in the close vicinity of a quantum critical point. Resistivity measurements under pressure further confirm the non-Fermi liquid behavior in a large temperature–pressure range. The magnetic susceptibility is found to follow the typical behavior for a one-dimensional spin chain from 300 K down to T *, and first-principles calculations predict flat Fermi surfaces for the itinerant f-electron bands. These suggest that CeCo 2 Ga 8 is a rare example of the quasi-one-dimensional Kondo lattice, but its non-Fermi liquid behaviors resemble those of the quasi-two-dimensional YbRh 2 Si 2 family. The study of the quasi-one-dimensional CeCo 2 Ga 8 family may therefore help us to understand the role of dimensionality on heavy fermion physics and quantum criticality.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗