Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Atomic Interface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Exploring New Science Domains with Atom Probe Tomography Enabled by an Environmental Transfer Hub

The liquid/solid and gas/solid interface represents a rich scientific and technological frontier for discovery and innovation in many areas of science. However, the direct nano- to atomic-scale characterization of these interfaces is technically challenging within broad range of analytical tools that require high to ultrahigh vacuum conditions. This challenge has been largely addressed within the electron microscopy (EM) community through the development of unique specimen holders and differentially-pumped vacuum systems that allow researchers to probe, in situ, liquid/solid and gas/solid interfaces using electron probes [1]. However, the direct application of APT to liquid/solid and gas/solid interfaces is not possible and requires the development of unique specimen preparation and handling of cryogenically-frozen specimens and/or work with specimens under environmentally-protected conditions. At PNNL, we have developed unique suite of hardware and experimental protocols for the preparation and handling of environmentally-sensitive materials centered around the combination of a unique environmental transfer hub, specimen suitcase device, and modified cryo FIB/SEM capabilities (Fig. 1a) [2-3]. The ability to prepare, manipulate, and transfer specimens under either cryogenic or vacuum conditions thus provides a means to uniquely apply APT analysis to a wide variety of material systems that would not be possible otherwise. Here we describe some specific examples, shown in Figure 1b, of APT analysis applied to temperature sensitive material systems requiring cryo specimen preparation and transfer, as well as air sensitive materials systems requiring vacuum or inert vacuum transfer.

Cryo atom probe tomography, Atom Probe, cryogenic ↗
DOE OSTI2019

Confinement of magnetism in atomically thin La0.7Sr0.3CrO3/La0.7Sr0.3MnO3 heterostructures

Abstract At crystalline interfaces where a valence-mismatch exists, electronic, and structural interactions may occur to relieve the polar mismatch, leading to the stabilization of non-bulk-like phases. We show that spontaneous reconstructions at polar La 0.7 Sr 0.3 MnO 3 interfaces are correlated with suppressed ferromagnetism for film thicknesses on the order of a unit cell. We investigate the structural and magnetic properties of valence-matched La 0.7 Sr 0.3 CrO 3 /La 0.7 Sr 0.3 MnO 3 interfaces using a combination of high-resolution electron microscopy, first principles theory, synchrotron X-ray scattering and magnetic spectroscopy and temperature-dependent magnetometry. A combination of an antiferromagnetic coupling between the La 0.7 Sr 0.3 CrO 3 and La 0.7 Sr 0.3 MnO 3 layers and a suppression of interfacial polar distortions are found to result in robust long-range ferromagnetic ordering for ultrathin La 0.7 Sr 0.3 MnO 3 . These results underscore the critical importance of interfacial structural and magnetic interactions in the design of devices based on two-dimensional oxide magnetic systems.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Atomic structure and bonding of the interfacial bilayer between Au nanoparticles and epitaxially regrown MgAl{sub 2}O{sub 4} substrates

A unique metal/oxide interfacial bilayer formed between Au nanoparticles and MgAl{sub 2}O{sub 4} substrates following thermal treatment is reported. Associated with the formation of the bilayer was the onset of an abnormal epitaxial growth of the substrate under the nanoparticle. According to the redistribution of atoms and the changes of their electronic structure probed across the interface by a transmission electron microscopy, we suggest two possible atomic models of the interfacial bilayer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Evolution of the structure and chemical composition of the interface between multi-component silicate glasses and yttria-stabilized zirconia after 40,000 h exposure in air at 800 °C

The chemical and structural stability of two commercial multicomponent silicate glasses (SCN and G6) in contact with yttria-stabilized zirconia (YSZ) was investigated after exposure times of up to 40,000 h in air at 800 °C. With exposure time, interfacial layers develop at the SCN-YSZ and G6-YSZ interfaces, which were characterized in detail using both quantitative chemical analysis and atomic-resolution imaging. At the SCN-YSZ interface, a Ca-Ba-Si-O reaction phase was found to grow by diffusion control. In G6-YSZ, Raman spectroscopy and electron microscopy revealed a disorganized interfacial reaction later between G6 and YSZ, and the occurrence of cubic to tetragonal to monoclinic phase transformations in YSZ. Finally, this microstructural evolution is discussed in terms of devitrification resistance of glass and diffusion processes at interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Passivation of oxide traps and interface states in GaAs metal-oxide-semiconductor capacitor by LaTaON passivation layer and fluorine incorporation

GaAs metal-oxide-semiconductor capacitor with TaYON/LaTaON gate-oxide stack and fluorine-plasma treatment is fabricated and compared with its counterparts without the LaTaON passivation interlayer or the fluorine treatment. Experimental results show that the sample exhibits better characteristics: low interface-state density (8 × 10{sup 11 }cm{sup −2}/eV), small flatband voltage (0.69 V), good capacitance-voltage behavior, small frequency dispersion, and small gate leakage current (6.35 × 10{sup −6} A/cm{sup 2} at V{sub fb} + 1 V). These should be attributed to the suppressed growth of unstable Ga and As oxides on the GaAs surface during gate-oxide annealing by the LaTaON interlayer and fluorine incorporation, and the passivating effects of fluorine atoms on the acceptor-like interface and near-interface traps.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Hierarchically Structured Catalysts Toward Sustainable Hydrogen Economy: Electro‐ and Thermo‐Chemical Pathways

Abstract Hydrogen, as an important clean energy source, plays a more and more crucial role in decarbonizing the planet and meeting the global climate challenge due to its high energy density and zero‐emission. The demand for sustainable hydrogen is increasing drastically worldwide as driven by the global shift towards low‐carbon energy solutions. Thermochemical catalysis process dominates hydrogen production at scale given its relatively mature technology and commercialization status, as well as the established manufacturing infrastructure. While due to its environmentally friendly nature and growing abundant sources of renewable electricity, the electrochemical path for hydrogen production is rising as a major alternative to the thermochemical means. Nevertheless, hierarchically structured catalysts and devices have gradually taken the center stage toward replacing the traditional counterparts, especially with the rapid advancement of the design and manufacture of such ordered nanostructure assemblies toward high activity, efficient mass transport, and superb stability. In this review, the latest progress of the hierarchically structured catalysts for hydrogen production have been surveyed on electro‐ and thermo‐ chemical pathways comparatively. It covers the structure designs of atomic dispersion, nanoscale surfaces and interfaces for achieving highly active and durable catalysts, components, and devices. Both electrochemical and thermochemical approaches are reviewed in terms of the vast design details, engineered benefits, and understandings of various Pt‐group metal (PGM) and non‐PGM based transition metal catalysts for hydrogen production. As the growing trend, brief discussions are also presented toward the high‐level assembly and manufacture of complexly structured components and devices at scale in the electrochemical and thermochemical energy systems.

Deng, Chenxin↗
DOE OSTI2018

Isotope- and Thickness-Dependent Friction of Water Layers Intercalated Between Graphene and Mica

The lubricating properties of water have been discussed extensively for millennia. Water films can exhibit wearless high friction in the form of cold ice, or act as lubricants in skating and skiing when a liquid. At the fundamental level, friction is the result of a balance between the rate of energy generation by phonon excitation during sliding and drainage of the energy from the interface by coupling with bulk atoms. Using atomic force microscopy, we found that when H 2 O intercalates between graphene and mica, it increases the friction between the tip and the substrate, dependent on the thickness of the water and graphene layers, while the magnitude of the increase in friction was reduced by D 2 O intercalation. With the help of first-principles density functional theory calculations, we explain this unexpected behavior by the increased spectral range of the vibration modes of graphene caused by water, and by better overlap of the graphene vibration modes with mica phonons, which favors more efficient energy dissipation. Finally, the larger increase in friction with H 2 O versus D 2 O shows that the high-frequency vibration modes of the water molecules play a very important role in the transfer of the vibrational energy of the graphene to the phonon bath of the substrate.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Corrosion Behavior of a Reactive Bond Between Stainless Steel and a Cast AlCeMg Alloy

Corrosion is a longstanding issue for metal components, especially those used in heat exchanger applications. Al–Ce–Mg alloys may provide a potential solution to this problem due to their good mechanical properties and potential reaction bonding with other metals. The reaction bonding involves a “reactive” bond that occurs upon casting of Al–Ce–Mg alloy over stainless steel (SS). Here this study examined the corrosion response of Al–2Ce–6Mg (atomic percent)/(SS) reactive bond interfaces after samples were completely submerged in nitric, sulfuric, formic, and mixed acids for 267 h. Scanning electron microscopy revealed that in the as-cut condition, reactive bond formations were seen frequently throughout the length of the casting and maintained a secure bond between the alloy and the SS tubes. Furthermore, the nitric, sulfuric, and the mixed acids did not have a deleterious effect on the reactive bond structure. However, formic acid did produce changes in both the microstructural appearance and the elemental profile across the bond due to the formation of corrosion reaction products on the acid-exposed surface.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The complexity of { 11 2 ¯ 1 } twin interface structure and energetics in HCP materials

Here, the quest for a deeper understanding of the mechanical properties of HCP alloys has been an ongoing effort. Due to the lack of a sufficient number of slip systems, twin nucleation and migration originate as a substantial plastic deformation mechanism in HCP metals. The paper uncovers the energetics and atomistic mechanism of the {$11\overline{2}1$} < $11\overline{2}6$ > which is one of the most prominent twin modes in HCP materials that has not been fully understood. In view of corrugated {$11\overline{2}1$} interfaces, the positioning of lattice/motif atoms needs to be clarified. First, we establish the initial twin boundary (TB) structure unambiguously via the lattice offsets resulting in volume invariancy and correct relative positioning of the twin variants. Secondly, the TB migration mechanism is determined from a crystallographic (zero net shuffle, $Σ\vec{s}$ = 0) and energetic standpoints (minimum energy path). The Generalized Planar Fault Energy (GPFE) curves are calculated for Ti, Hf, Mg, and Zr. Such GPFE curves for this twin mode are calculated for the first time, and point to unusually high unstable energies (300-850 mJ/m 2 ), and low migration barriers (<60 mJ/m 2 ) for twinning accompanied with large shuffle magnitudes, |$\vec{s}$|, comparable to the Burger’s vector (|$\vec{s}$| ≅ $b_e$ > 0.44Å)

36 MATERIALS SCIENCE↗
DOE OSTI2014

Displacement Threshold Energy and Recovery in an Al-Ti Nanolayered System with Intrinsic Point Defect Partitioning

A method is established and validated using molecular dynamics (MD) to determine the displacement threshold energies as Ed in nanolayered, multilayered systems of dissimilar metals. The method is applied to specifically oriented nanolayered films of Al-Ti where the crystal structure and interface orientations are varied in atomic models and Ed is calculated. Methods for defect detection are developed and discussed based on prior research in the literature and based on specific crystallographic directions available in the nanolayered systems. These are compared and contrasted to similar calculations in corresponding bulk materials, including fcc Al, fcc Ti, hcp Al, and hcp Ti. In all cases, the calculated Ed in the multilayers are intermediate to the corresponding bulk values but exhibit some important directionality. In the nanolayer, defect detection demonstrated systematic differences in the behavior of Ed in each layer. Importantly, collision cascade damage exhibits significant defect partitioning within the Al and Ti layers that is hypothesized to be an intrinsic property of dissimilar nanolayered systems. This type of partitioning could be partly responsible for observed asymmetric radiation damage responses in many multilayered systems. In addition, a pseudo-random direction was introduced to approximate the average Ed without performing numerous simulations with random directions.

Al-Ti↗
DOE OSTI2018

Tribology of two-dimensional materials: From mechanisms to modulating strategies

Two-dimensional (2D) materials are crystalline materials made of a single or a few layers of atoms. They have been an active research subject in recent years because of their unique physical and chemical properties. In particular, 2D materials such as graphene, hexagonal BN, and MoS 2 exhibit some of the lowest friction coefficients and wear rates, making them attractive for enhancing the efficiency, durability, and environmental compatibility of future mechanical systems. This review will focus on recent advances in the tribology of 2D materials. Starting from general physical characteristics, the essential friction and wear behavior of 2D materials together with the associated mechanisms are reviewed for both interlayer and surface sliding. Influences of the atomic structures of the slip interfaces and environmental factors are discussed, with special attention given to various strategies for achieving friction modulation and superlubricity. Finally, the emerging engineering applications of 2D materials, as well as future prospects, are summarized.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Building Durable Multimetallic Electrocatalysts from Intermetallic Seeds

When combined with earth-abundant metals, Pt-based alloy nanoparticles (NPs) can be cost-effective electrocatalysts. However, these NPs can experience leaching of non-noble-metal components under harsh electrocatalytic conditions. In this work, the Skrabalak group has demonstrated a novel NP construct in which Pt-based random alloy surfaces are stabilized against non-noble-metal leaching by their deposition onto intermetallic seeds. These core@shell NPs are highly durable electrocatalysts, with the ability to tune catalytic performance by the core@shell architecture, surface alloy composition, and NP shape. This versatility was demonstrated in a model system in which random alloy (ra-) PtM surfaces were deposited onto ordered intermetallic (i-) PdCu seeds using seed-mediated co-reduction (SMCR). In the initial demonstration, ra-PtCu shells were deposited on i-PdCu seeds, with these core@shell NPs exhibiting higher specific and mass activities for the oxygen reduction reaction (ORR) when compared to similarly sized ra-PtCu NPs. These NPs also showed outstanding durability, maintaining ~85% in specific activity after 5000 cycles. Characterization of the NPs after use revealed minimal loss of Cu. The activity enhancement was attributed to the strained surface that arises from the lattice mismatch between the intermetallic core and random alloy surface. The outstanding durability was attributed to the ordered structure of the intermetallic core. The origin of this durability enhancement was investigated by classical molecular dynamics simulations, where Pt atoms were found to have a lower potential energy when deposited on an intermetallic core than when deposited on a random alloy core. Also, ordering of Cu atoms at the core@shell interface appears to enhance the overall binding between the core and the shell materials. Inspired by this initial demonstration, SMCR has been used to achieve shells of different random alloy compositions, PtM (M = Ni, Co, Cu, or Fe). This advance is significant because ligand effects vary as a function of PtM identity and Pt/M ratio. These features also influence the degree of surface strain imparted from the lattice mismatch between the core and shell materials. Like the initial demonstration, standout features of these core@shell NPs were high durability and resistance to non-noble metal leaching. Moving forward, efforts have been directed toward integrating shape-control to this core@shell NP construct. This integration is motivated by the shape-dependent catalytic performance of NPs derived from the selective expression of specific facets. Considering the initial i-PdCu@ra-PtCu system, NPs with a cubic shape have been achieved by judicious selection of capping ligands during SMCR. Evaluation of these NPs as catalysts for the electrooxidation of formic acid found that the nanocubic shape enhances catalytic performance compared to similar core@shell NPs with a spherical morphology. We envision that SMCR can be applied to other NP systems to achieve highly durable catalysts as the syntheses of monodisperse and shape-controlled intermetallic seeds are advanced. This Account highlights the role of intermetallic cores in providing more durable electrocatalysts. More broadly, the versatility of SMCR is highlighted as a route to integrate architecture, alloy surfaces, and shape within one NP system, and how this achievement is inspiring new high-performance and robust catalysts is discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

The Unexpected Role of Cations in the Self-Assembly of Positively Charged Amphiphiles at Liquid/Liquid Interfaces

Conventional wisdom suggests that cations play a minimal role in the assembly of cationic amphiphiles. Here, we show that at liquid/liquid (L/L) interfaces, specific cation effects can modulate the assemblies of hydrophobic tails in an oil phase despite being attached to cationic headgroups in the aqueous phase. In this work, we used oligo-dimethylsiloxane (ODMS) methyl imidazolium amphiphiles to identify these specific interactions at hexadecane/aqueous interfaces. Small cations, such as Li + , bind to the O atoms in the ODMS tail and pin it to the interface, thereby imposing a kinked conformation-as evidenced by vibrational sum frequency generation spectroscopy and molecular dynamics simulations. While larger Cs + ions more readily partition to the interface, they do not form analogous complexes. Our data not only point to ways for controlling amphiphile structure at L/L interfaces but also suggest a means for the separation of Li + , or related applications, in soft-matter electronics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Atomic-Scale Observation of O1 Faulted Phase-Induced Deactivation of LiNiO 2 at High Voltage

LiNiO 2 and cobalt-free ultrahigh-Ni content cathodes suffer from rapid capacity loss and severe chemomechanical degradation, especially when operated at high voltages. Here, by cycling LiNiO 2 up to 4.7 V, we report the atomic-scale observation of O1 faulted phase-induced deactivation of LiNiO 2 . We found that although a thin layer of O3 phase forms on the particle surface by reversible O3 → O1 transformation during discharge, the bulk interior still maintains the O1 faulted phase, leading to rapid capacity loss of LiNiO 2 . Moreover, the atomic configuration of the O1/O3 interface is investigated comprehensively. We found that the misfit along the c axes of the O1 and O3 phases results in the formation of misfit dislocations, whereby cation mixing is promoted at dislocation cores. Further, a transition zone with continuous shear along the a-b plane is uncovered between the O1 and O3 phases for the first time. Besides, severe oxygen loss-induced pore formation and concurrent rock salt transformation are also identified.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Ni Nanoparticles on CeO 2 (111): Energetics, Electron Transfer, and Structure by Ni Adsorption Calorimetry, Spectroscopies, and Density Functional Theory

The morphology, interfacial bonding energetics and charge transfer of Ni clusters and nanoparticles on slightly-reduced CeO 2-x (111) surfaces at 100 to 300 K have been studied using single crystal adsorption calorimetry (SCAC), low-energy ion scattering spectroscopy (LEIS), Xray photoelectron spectroscopy (XPS), low energy electron diffraction (LEED) and density functional theory (DFT). The initial heat of adsorption of Ni vapor decreased with the extent of pre-reduction (x) of the CeO 2-x (111), showing that stoichiometric ceria adsorbs Ni more strongly than oxygen vacancies. On CeO 1.95 (111) at 300 K, the heat dropped quickly with coverage in the first 0.1 ML, attributed to nucleation of Ni clusters on stoichiometric steps, followed by the Ni particles spreading onto less favorable terrace sites. At 100 K, the clusters nucleate on terraces due to slower diffusion. Adsorbed Ni monomers are in the +2 oxidation state, and they bind by ~45 kJ/mol more strongly to step sites than terraces. The measured heat of adsorption versus average particle size on terraces is favorably compared to DFT calculations. The Ce 3d XPS lineshape showed an increase in Ce 3+ /Ce 4+ ratio with Ni coverage, providing the number of electrons donated to the ceria per Ni atom. The charge transferred per Ni is initially large but strongly decreases with increasing cluster size for both experiments and DFT, and shows large differences between clusters at steps versus terraces. This charge is localized on the interfacial Ni and Ce atoms in their atomic layers closest to the interface. This knowledge is crucial to understanding the nature of the active sites on the surface of Ni-CeO 2 catalysts for which metal-oxide interactions play a very important role in the activation of O-H and C-H bonds. In conclusion, the changes in these interactions with Ni particle size (metal loading) and the extent of reduction of the ceria help to explain how previously reported catalytic activity and selectivity change with these same structural details.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Lattice thermal transport in two-dimensional alloys and fractal heterostructures

Abstract Engineering thermal transport in two dimensional materials, alloys and heterostructures is critical for the design of next-generation flexible optoelectronic and energy harvesting devices. Direct experimental characterization of lattice thermal conductivity in these ultra-thin systems is challenging and the impact of dopant atoms and hetero-phase interfaces, introduced unintentionally during synthesis or as part of deliberate material design, on thermal transport properties is not understood. Here, we use non-equilibrium molecular dynamics simulations to calculate lattice thermal conductivity of $${\mathrm {(Mo|W)Se_2}}$$ ( Mo | W ) Se 2 monolayer crystals including $${\mathrm {Mo}}_{1-x}{\mathrm {W}}_x{\mathrm {Se_2}}$$ Mo 1 - x W x Se 2 alloys with substitutional point defects, periodic $${\mathrm {MoSe_2}|\mathrm {WSe_2}}$$ MoSe 2 | WSe 2 heterostructures with characteristic length scales and scale-free fractal $${\mathrm {MoSe_2}}|{\mathrm {WSe_2}}$$ MoSe 2 | WSe 2 heterostructures. Each of these features has a distinct effect on phonon propagation in the crystal, which can be used to design fractal and periodic alloy structures with highly tunable thermal conductivities. This control over lattice thermal conductivity will enable applications ranging from thermal barriers to thermoelectrics.

42 ENGINEERING↗
DOE OSTI2023

Structural basis underlying the synergism of NADase and SLO during group A Streptococcus infection

Group A Streptococcus (GAS) is a strict human pathogen possessing a unique pathogenic trait that utilizes the cooperative activity of NAD + -glycohydrolase (NADase) and Streptolysin O (SLO) to enhance its virulence. How NADase interacts with SLO to synergistically promote GAS cytotoxicity and intracellular survival is a long-standing question. Here, the structure and dynamic nature of the NADase/SLO complex are elucidated by X-ray crystallography and small-angle scattering, illustrating atomic details of the complex interface and functionally relevant conformations. Structure-guided studies reveal a salt-bridge interaction between NADase and SLO is important to cytotoxicity and resistance to phagocytic killing during GAS infection. Furthermore, the biological significance of the NADase/SLO complex in GAS virulence is demonstrated in a murine infection model. Overall, this work delivers the structure-functional relationship of the NADase/SLO complex and pinpoints the key interacting residues that are central to the coordinated actions of NADase and SLO in the pathogenesis of GAS infection.

59 BASIC BIOLOGICAL SCIENCES↗