Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AIRFOILS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Design and Experimental Results for a Low-Speed, Flapped, Slotted, Natural-Laminar-Flow Airfoil

A 12.91-percent-thick, flapped, slotted, natural-laminar-flow (SNLF) airfoil, the S702, intended for a low-speed, fixed-wing aircraft has been designed and analyzed theoretically and verified experimentally in The Pennsylvania State University Low-Speed, Low- Turbulence Wind Tunnel. The two primary objectives of high maximum lift, insensitive to roughness, and low profile drag have been achieved. The airfoil exhibits a sharp stall that is less abrupt than the stalls of earlier SNLF airfoils, which meets the design objective. The constraint on the pitching moment has been satisfied. Comparisons of the theoretical and experimental results show reasonably good agreement overall, given the complexity of the configuration.

slotted airfoil↗

Design and Optimization of a Gas-Cooled, Airfoil Fin Microchannel Heat Exchanger

High-performance microchannel heat exchangers are needed to supply heat for power conversion for nuclear microreactors. An airfoil fin microchannel design, constructed of Alloy 617 with helium as the working fluid, was analyzed and optimized using a design of experiments with artificial intelligence and machine learning techniques. The use of airfoil fins offers the potential to reduce pressure drop across the heat exchanger, as compared to other types of channel configurations. A framework for topology optimization of airfoil fin PCHEs has been developed that can be readily extended to different fin sizes and shapes, as well as different inlet and operating conditions, materials of construction, and working fluids. An optimization procedure was developed that employs computational fluid dynamics for a set of design points identified using Latin hypercube sampling. STAR-CCM+ was used to analyze a simplified two-channel configuration where five parameters were varied – inlet angle, fin scale, extent of staggering, transverse and longitudinal pitches. Two methods were compared for generating surrogate models – a 5D polynomial and a regression neural network. A response surface approximation was created from the surrogate models and input to a genetic algorithm. The genetic algorithm identified a set of optimal points on the Pareto front. The optimal geometry was found across six channel Reynolds numbers ranging from 1000 to 5000 to analyze how varying inlet conditions affects the optimal design. A set of optimal designs that maximizes heat transfer and minimizes pressure drop was identified, and a thermal stress analysis was performed on the optimal design. This work has developed a digital framework for the expedient topology design and evaluation of PCHE designs for gas-cooled microreactor applications. Correlations for the Nusselt number and Darcy friction factor were developed that can be useful for thermal hydraulic analyses using system codes. A thermal stress analysis was conducted and a brief discussion of the status of code cases of PCHEs for nuclear applications is given. Testing and thermomechanical modeling is needed to facilitate future code compliance of PCHEs for high pressure and high temperature applications.

42 ENGINEERING↗

Effect of changing the mean camber of an airfoil section

Methodical experiments with the series of airfoil sections of the same relative thickness and of variable relative cambers can be utilized for determining the effect of the camber on the aerodynamic properties of airfoil sections.

AIRFOILS - S T AE 13A (S C 96-104) (ROYER) - CHARA↗

A parametric study on leading-edge slots used on wind turbine airfoils at various angles of attack

Here in the present work, a narrow span-wise rectangular channel (referred to as a slot) is introduced and drilled near the leading edge of a finite-span cambered airfoil to study its impact on the overall aerodynamic performance. This slot starts from the vicinity of the leading edge and exits from the pressure-side of the airfoil after making a slight turn. NACA 4412 is used as the baseline airfoil profile, and the influence of several geometrical parameters of the slot at the chord-based Reynolds number of 1.6 M, and different angles of attack (AoAs) ranging from 0 to 16° on the lift and drag coefficients are investigated. The effect of slot's width (thickness), inlet angle, and vertical position are studied, and the appropriate range of values for each variable is determined. For one of the best cases examined, a lift coefficient improvement as large as 30% is observed, while the drag penalty is insignificant. Computational fluid dynamics (CFD) method is used for modeling and analysis, and the results are validated against both published data and the data from a set of wind-tunnel experiments.

17 WIND ENERGY↗

Wind Turbine Airfoil Design Tools

SAND2025-11738O Wind Turbine Airfoil Design Tools is a software tool that connects existing open-source airfoil analysis tools with optimization software to produce modern airfoil design for wind turbine applications. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

Maniaci, David↗

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors. Part 1: Analysis and design of stages A, B, and C

A conventional rotor and stator, two dual-airfoil tandem rotors, and one dual-airfoil tandem stator were designed. The two tandem rotors were each designed with different percentages of the overall lift produced by the front airfoil. Velocity diagrams and blade leading and trailing edge metal angles selected for the conventional rotor and stator blading were used in the design of the tandem blading. Rotor inlet hub/tip ratio was 0.8. Design values of rotor tip velocity and stage pressure ratio were 757 ft/sec and 1.30, respectively.

Brent, J. A.↗

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors. Part 3: Data and performance for stage C

Stage C, comprised of tandem-airfoil rotor C and tandem-airfoil stator B, was designed and tested to establish performance data for comparison with the performance of conventional single-airfoil blading. Velocity diagrams and blade leading and trailing edge metal angles selected for the conventional rotor and stator blading were used in the design of the tandem blading. The rotor had an inlet hub/tip ratio of 0.8 and a design tip velocity of 757 ft/sec. At design equivalent rotor speed, rotor C achieved a maximum adiabatic efficiency of 91.8% at a pressure ratio of 1.31. The stage maximum adiabatic efficiency was 86.5% at a pressure ratio of 1.31.

Brent, J. A.↗

Single stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors. Part 4: Data and performance for stage B

Stage B, composed of tandem-airfoil rotor B and stator B, was tested with uniform inlet flow and with hub radial, tip radial and 90 degree one-per-revolution circumferential distortion of the inlet flow as part of an overall program to evaluate the effectiveness of tandem airfoils for increasing the design point loading capability and stable operating range of rotor and stator blading. The results of this series of tests provide overall performance and blade element data for evaluating: (1) the potential of tandem blading for extending the loading limit and stable operating range of a stage representative of a middle stage of an advanced high pressure compressor, (2) the effect of loading split between the two airfoils in tandem on the performance of tandem blading, and (3) the effects of inlet flow distortion on the stage performance. The rotor had an inlet hub/tip ratio of 0.8 and a design tip velocity of 757 ft/sec. With uniform inlet flow, rotor B achieved a maximum adiabatic efficiency of 88.4% at design equivalent rotor speed and a pressure ratio of 1.31. The stage maximum adiabatic efficiency at design equivalent rotor speed with uniform inlet flow was 82.5% at a pressure ratio of 1.28. Tip radial and circumferential distortion of the inlet flow caused substantial reductions in surge margin.

Brent, J. A.↗

Low-speed aerodynamic characteristics of an airfoil optimized for maximum lift coefficient

An investigation has been conducted in the Langley low-turbulence pressure tunnel to determine the two-dimensional characteristics of an airfoil optimized for maximum lift coefficient. The design maximum lift coefficient was 2.1 at a Reynolds number of 9.7 million. The airfoil with a smooth surface and with surface roughness was tested at angles of attack from 6 deg to 26 deg, Reynolds numbers (based on airfoil chord) from 2.0 million to 12.9 million, and Mach numbers from 0.10 to 0.35. The experimental results are compared with values predicted by theory. The experimental pressure distributions observed at angles of attack up to at least 12 deg were similar to the theoretical values except for a slight increase in the experimental upper-surface pressure coefficients forward of 26 percent chord and a more severe gradient just behind the minimum-pressure-coefficient location. The maximum lift coefficients were measured with the model surface smooth and, depending on test conditions, varied from 1.5 to 1.6 whereas the design value was 2.1.

Bingham, G. J.↗

Computational considerations in application of the finite element method for analysis of unsteady flow around airfoils.

Difficulties related to the application of the finite element method for numerical solution of the Navier-Stokes equation are discussed. The unsteady flow around a stationary and oscillating NACA 0012 airfoil was analyzed. In an effort to establish the range of applicability of the developed numerical method, the accuracy and stability problems in representing unsteady flow patterns and determining pressure distribution around the airfoil were investigated. Error involved in determining the velocity field and in the numerical integration of the discretized equations were analyzed in terms of geometry of the finite element gridwork, boundary conditions for stationary and oscillating airfoils, angles of attack and flow conditions.

Bratanow, T.↗

The effects of leading-edge serrations on reducing flow unsteadiness about airfoils, an experimental and analytical investigation

High frequency surface pressure measurements were obtained from wind-tunnel tests over the Reynolds number range 1.2 times one million to 6.2 times one million on a rectangular wing of NACA 63-009 airfoil section. Measurements were also obtained with a wide selection of leading-edge serrations added to the basic airfoil. Under a two-dimensional laminar bubble very close to the leading edge of the basic airfoil there is a large apatial peak in rms pressure. Frequency analysis of the pressure signals in this region show a large, high-frequency energy peak which is interpreted as an oscillation in size and position of the bubble. The serrations divide the bubble into segments and reduce the peak rms pressures. A low Reynolds number flow visualization test on a hydrofoil in water was also conducted. A von Karman vortex street was found trailing from the rear of the foil. Its frequency is at a much lower Strouhal number than in the high Reynolds number experiment, and is related to the trailing-edge and boundary-layer thicknesses.

Schwind, R. G.↗

Low speed aerodynamic characteristics of a 17 percent thick airfoil section designed for general aviation applications

Wind-tunnel tests have been conducted to determine the low-speed two-dimensional aerodynamic characteristics of a 17-percent-thick airfoil designed for general aviation applications (GA(W)-1). The results were compared with predictions based on a theoretical method for calculating the viscous flow about the airfoil. The tests were conducted over a Mach number range from 0.10 to 0.28. Reynolds numbers based on airfoil chord varied from 2.0 million to 20.0 million. Maximum section lift coefficients greater than 2.0 were obtained and section lift-drag ratio at a lift coefficient of 1.0 (climb condition) varied from about 65 to 85 as the Reynolds number increased from about 2.0 million to 6.0 million.

Mcghee, R. J.↗

Low-speed aerodynamic characteristics of airfoil sections with rounded trailing edges in forward and reverse flow

Low-speed wind-tunnel tests were conducted to determine the two-dimensional aerodynamic characteristics of 6-, 12-, and 18-percent-thick airfoil sections with rounded trailing edges in both forward and reverse flow. The shapes incorporated camber with both the leading and trailing edges rounded to provide reasonable aerodynamic performance with either edge directed toward the free-stream flow. The tests were conducted with the airfoils in both normal and reverse orientations relative to the free stream. The Mach number was varied from 0.16 to 0.36 and the angle of attack was varied from minus 10 to 24 million. Reynolds number, based on the airfoil chord, was varied from about 1.0 to 12.0 million.

Beasley, W. D.↗

Dynamic stall modeling and correlation with experimental data on airfoils and rotors

Two methods for modeling dynamic stall have been developed. The alpha, A, B method generates lift and pitching moments as functions of angle of attack and its first two time derivatives. The coefficients are derived from experimental data for oscillating airfoils. The Time Delay Method generates the coefficients from steady state airfoil characteristics and an associated time delay in stall beyond the steady state stall angle. Correlation with three types of test data shows that the alpha, A, B method is somewhat better for use in predicting helicopter rotor response in forward flight. Correlation with lift and moment hysteresis loops generated for oscillating airfoils was good for both models.

Carlson, R. G.↗

New airfoil sections for general aviation aircraft

A program has been undertaken to develop new airfoil sections suitable for general aviation aircraft, utilizing theoretical and experimental advanced technology developed in recent years primarily for subsonic jet transport and military aircraft. The airfoil development program is one component of the Advanced Technology Light Twin program sponsored by NASA Langley Research Center. Two-dimensional tests of a new airfoil have demonstrated high cruising performance over a fairly wide C sub 1 range, and a C sub 1 max value of 3.69 with Fowler flap and no leading-edge devices. Experimental and theoretical development of additional configurations is under way.

Wentz, W. H., Jr.↗

Investigation of acoustic effects of leading-edge serrations on airfoils

This paper presents and interprets a series of extensive studies of the application of leading-edge serrations as a device for reducing the vortex noise radiated from stationary and rotating airfoils in low Reynolds number flow. In these studies, a variety of serrations were attached at selected locations near the leading edge of stationary and rotating airfoils. The noise levels of the airfoils were reduced considerably with the serrations attached. An explanation of the aeroacoustic flow mechanisms involved is given.

Hersh, A. S.↗

Low-speed aerodynamic characteristics of a 13.1-percent-thick, high-lift airfoil

Experimental study of the low-speed, sectional characteristics of a high-lift airfoil, and comparison of these characteristics with the predictions of the theoretical methods used in the airfoil's design. The 13.1% thick UI-1720 airfoil was found to achieve the predicted maximum lift coefficient of nearly 2.0. No upper-surface flow separation was found below the stall angle of attack of 16 deg; it appeared that stall was due to an abrupt leading-edge flow separation.

Sivier, K. R.↗