Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AIR FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Laser-spectroscopic measurement techniques for hypersonic, turbulent wind tunnel flows

A review is given of the nature, present status, and capabilities of two laser spectroscopic methods for the simultaneous measurement of temperature, density, and their fluctuations owing to turbulence in high speed wind tunnel flows. One method is based on the two frequency excitation of nitric oxide seeded into a nitrogen flow, using tunable dye lasers. The second, more recent method relies on the excitation of oxygen in air flows using a tunable, ArF excimer laser. Signal are obtained from both the laser induced fluorescence and from Raman scattering of the same laser pulse. Measurements are demonstrated in the turbulent boundary layer of a Mach-2 channel flow.

Mckenzie, Robert L.↗
NASA NTRS1995

Characterization of a hot-film probe for hypersonic flow

The critical issues concerning the application of constant-temperature hot-film anemometry to hypersonic flow are reviewed and extended. Mass-flux static calibrations were conducted in a Mach 10 helium flow, while mass-flux and total-temperature static calibrations were made in a Mach 6 air flow. In addition, comparative hot-film/hot-wire turbulence measurements were made in a Mach 11 helium boundary layer to provide insight into the dynamic response of the hot film. The measurements indicate that substrate conduction 'losses' dominate the static response of the hot-film probe, thus resulting in poor sensitivity to mass-flux and total temperature. Furthermore, it has been found that it is not possible to isolate mass-flux fluctuations at high overheat ratios for the current hot-film design. Thus, the sapphire-substrate hot-film anemometer is a robust, high-bandwidth instrument limited to qualitative transition and turbulence measurements. Finally, the extension of this technique to providing quantitative information is dependent upon the development of lower thermal-conductivity substrate materials.

Sheplak, M.↗
NASA NTRS1956

Exhaust Nozzles for Supersonic Flight with Turbojet Engines

Good internal performance over a wide range of flight conditions can be obtained with either a plug nozzle or a variable ejector nozzle that can provide a divergent shroud at high pressure ratios. For both the ejector and the plug nozzle, external flow can sometimes cause serious drag losses and, for some plug-nozzle installations, external flow can cause serious internal performance losses. Plug-nozzle cooling and design of the secondary-air-flow systems for ejectors were also considered .

Shillito, Thomas B.↗
NASA NTRS2018

P43K-3884 Characterizing Martian Crater Circulations with the NASA Ames Mars GCM

Observations made in Gale Crater by instruments on the MSL Curiosity Rover show that the diurnal amplitude of the surface pressure is increased and the depth of the Convective Boundary Layer (CBL) is decreased relative to other lander locations on flatter regions of Mars (Haberle et al., 2014; Moores et al., 2015). Mesoscale modeling studies of Gale Crater suggest that crater circulations produce these effects. Tyler & Barnes (2013) show that local upslope/downslope flows along the crater rim and Mt. Sharp amplify the diurnal pressure cycle. These same flows are thought to be at least partly responsible for the suppression of the CBL because upward air flow at the rim and in the center (due to Mt. Sharp) forces subsidence over the lowest regions of the crater during the day. Regional flows, largely due to the location of Gale near the dichotomy boundary, may also play a role in shaping the circulation internal to the crater. Whether the behavior of the CBL and the amplified diurnal pressure cycle are phenomena observed in craters morphologically different from Gale (i.e. bowl-shaped, irregular, degraded) is not yet understood. We will explore these questions by characterizing the behavior of these processes as they are shaped by the morphology of craters greater than 100 km in diameter. We use the NASA Ames Mars Global Circulation Model (GCM) that now utilizes the NOAA/GFDL cubed-sphere finite-volume dynamical core to examine ~100 craters of varying size and shape from a database of known Martian craters (Robbins & Hynek, 2014). Run at 7.5 km resolution, the GCM is capable of resolving surface winds, temperature, and pressure inside craters of this size allowing for the analysis of dozens of craters simulated at various seasons and within the context of synoptic and global-scale phenomena.

Batterson, Courtney MaryLou↗
NASA NTRS1946

Comparison of Several Methods of Predicting the Pressure Loss at Altitude Across a Baffled Aircraft-Engine Cylinder

Several methods of predicting the compressible-flow pressure loss across a baffled aircraft-engine cylinder were analytically related and were experimentally investigated on a typical air-cooled aircraft-engine cylinder. Tests with and without heat transfer covered a wide range of cooling-air flows and simulated altitudes from sea level to 40,000 feet. Both the analysis and the test results showed that the method based on the density determined by the static pressure and the stagnation temperature at the baffle exit gave results comparable with those obtained from methods derived by one-dimensional-flow theory. The method based on a characteristic Mach number, although related analytically to one-dimensional-flow theory, was found impractical in the present tests because of the difficulty encountered in defining the proper characteristic state of the cooling air. Accurate predictions of altitude pressure loss can apparently be made by these methods, provided that they are based on the results of sea-level tests with heat transfer.

Neustein, Joseph↗
NASA NTRS1987

Drop size distribution and air velocity measurements in air assist swirl atomizer sprays

Detailed measurements of mean drop size (SMD) and size distribution parameters have been made using a Fraunhofer diffraction particle sizing instrument in a series of sprays generated by an air assist swirl atomizer. Thirty-six different combinations of fuel and air mass flow rates were examined with liquid flow rates up to 14 lbm/hr and atomizing air flow rates up to 10 lbm/hr. Linear relationships were found between SMD and liquid to air mass flow rate ratios. SMD increased with distance downstream along the center line and also with radial distance from the axis. Increase in obscuration with distance downstream was due to an increase in number density of particles as the result of deceleration of drops and an increase in the exposed path length of the laser beam. Velocity components of the atomizing air flow field measured by a laser anemometer show swirling jet air flow fields with solid body rotation in the core and free vortex flow in the outer regions.

Mao, C.-P.↗
NASA NTRS2008

Parametric Study of High Frequency Pulse Detonation Tubes

This paper describes development of high frequency pulse detonation tubes similar to a small pulse detonation engine (PDE). A high-speed valve injects a charge of a mixture of fuel and air at rates of up to 1000 Hz into a constant area tube closed at one end. The reactants detonate in the tube and the products exit as a pulsed jet. High frequency pressure transducers are used to monitor the pressure fluctuations in the device and thrust is measured with a balance. The effects of injection frequency, fuel and air flow rates, tube length, and injection location are considered. Both H2 and C2H4 fuels are considered. Optimum (maximum specific thrust) fuel-air compositions and resonant frequencies are identified. Results are compared to PDE calculations. Design rules are postulated and applications to aerodynamic flow control and propulsion are discussed.

Cutler, Anderw D.↗
NASA NTRS1977

Soot formation in a turbulent swirling flow

The qualitative understanding of soot formation in simple models of gas turbine primary-zone combustors is summarized. Soot formation in flame radiation and air pollution was investigated. Results are presented, namely: (1) if the fuel is premixed with air in approximately stoichiometric proportions, the sequence of states that a fluid element undergoes as it burns is quite different from the sequence when liquid or vapor fuel is injected into an air-flow; (2) swirling flows, as are typical or swirl-can combustors, when burning, can amplify small aerodynamic disturbances upstream of the swirl vanes; and (3) different fuels form significantly different amounts of soot. Each of these effects makes major changes in the amount of soot formed in a given combustor.

Hoult, D. P.↗
NASA NTRS1924

Velocity and pressure distribution behind bodies in an air current

The following experiments on the air flow behind bodies were made for the purpose of assisting in the explanation of the phenomena connected with air resistance. The first two series of experiments dealt with the phenomena behind a cylinder. The third series of experiments was carried out behind a streamlined strut.

PRESSURE DISTRIBUTION - BODIES↗
NASA NTRS1941

The temperature of unheated bodies in a high-speed gas stream

The present report deals with temperature measurements on cylinders of 0.2 to 3 millimeters diameter in longitudinal and transverse air flow at speeds of 100 to 300 meters per second. Within the explored test range, that is, the probable laminar boundary layer region, the temperature of the cylinders in axial flow is practically independent of the speed and in good agreement with Pohlhausen's theoretical values; Whereas, in transverse flow, cylinders of certain diameter manifest a close relationship with speed, the ratio of the temperature above the air of the body to the adiabatic stagnation temperature decreases with rising speed and then rises again from a Mach number of 0.6. The importance of this "specific temperature" of the body for heat-transfer studies at high speed is discussed.

Eckert, E↗
NASA NTRS1996

Analysis of the Hydrodynamics and Heat Transfer Aspects of Microgravity Two-Phase Flows

Experimental results for void fractions, flow regimes, and heat transfer rates in two-phase, liquid-gas flows are summarized in this paper. The data was collected on-board NASA's KC-135 reduced gravity aircraft in a 9.525 mm circular tube (i.d.), uniformly heated at the outer surface. Water and air flows were examined as well as three glycerol/water solutions and air. Results are reported for the water-air data.

Rezkallah, Kamiel S.↗
NASA NTRS1991

Planar temperature measurement in compressible flows using laser-induced iodine fluorescence

A laser-induced iodine fluorescence technique that is suitable for the planar measurement of temperature in cold nonreacting compressible air flows is investigated analytically and demonstrated in a known flow field. The technique is based on the temperature dependence of the broadband fluorescence from iodine excited by the 514-nm line of an argon-ion laser. Temperatures ranging from 165 to 245 K were measured in the calibration flow field. This technique makes complete, spatially resolved surveys of temperature practical in highly three-dimensional, low-temperature compressible flows.

Hartfield, Roy J., Jr.↗
NASA NTRS1976

Emissions of an AVCO Lycoming 0-320-DIAD air cooled light aircraft engine as a function of fuel-air ratio, timing, and air temperature and humidity

A carbureted aircraft engine was operated over a range of test conditions to establish the exhaust levels over the EPA seven-mode emissions cycle. Baseline (full rich production limit) exhaust emissions at an induction air temperature of 59 F and near zero relative humidity were 90 percent of the EPA standard for HC, 35 percent for NOx, and 161 percent for CO. Changes in ignition timing around the standard 25 deg BTDC from 30 deg BTDC to 20 deg BTDC had little effect on the exhaust emissions. Retarding the timing to 15 deg BTDC increased both the HC and CO emissions and decreased NOx emissions. HC and CO emissions decreased as the carburetor was leaned out, while NOx emissions increased. The EPA emission standards were marginally achieved at two leanout conditions. Variations in the quantity of cooling air flow over the engine had no effect on exhaust emissions. Temperature-humidity effects at the higher values of air temperature and relative humidity tested indicated that the HC and CO emissions increased significantly, while the NOx emissions decreased.

Meng, P. R.↗
NASA NTRS1934

Analysis of spinning in a monoplane wing by the induction method as compared with the strip method

The problem of autorotation has been attacked by various authors, in particular Fuchs and Schmidt who applied the so-called strip method which is based upon the assumption that the forces and moments per unit length acting in each section of the wing are equal to those on an infinite cylindrical wing of equal section in an air flow of intensity and direction resulting from the apparent relative motion of this section with respect to the surrounding air. In other words they disregarded the induced velocities, which, however, are of such importance that their omission is bound to result in appreciable errors, as we attempt to prove in this report.

Poggi, L↗
NASA NTRS2017

Spontaneous Ignition of Hydrothermal Flames in Supercritical Ethanol Water Solutions

Results are reported from recent tests where hydrothermal flames spontaneously ignited in a Supercritical Water Oxidation (SCWO) Test Cell. Hydrothermal flames are generally categorized as flames that occur when appropriate concentrations of fuel and oxidizer are present in supercritical water (SCW); i.e., water at conditions above its critical point (218 atm and 374 C). A co-flow injector was used to inject fuel, comprising an aqueous solution of 30-vol to 50-vol ethanol, and air into a reactor held at constant pressure and filled with supercritical water at approximately 240 atm and 425 C. Hydrothermal flames auto-ignited and quickly stabilized as either laminar or turbulent diffusion flames, depending on the injection velocities and test cell conditions. Two orthogonal views, one of which provided a backlit shadowgraphic image, provided visual observations. Optical emission measurements of the steady state flame were made over a spectral range spanning the ultraviolet (UV) to the near infrared (NIR) using a high-resolution, high-dynamic-range spectrometer. Depending on the fuel air flow ratios varying degrees of sooting were observed and are qualitatively compared using light absorption comparisons from backlit images.

hydrothermal flame↗
NASA NTRS2009

Plasma torch for ignition, flameholding and enhancement of combustion in high speed flows

Preheating of fuel and injection into a plasma torch plume fro adjacent the plasma torch plume provides for only ignition with reduced delay but improved fuel-air mixing and fuel atomization as well as combustion reaction enhancement. Heat exchange also reduced erosion of the anode of the plasma torch. Fuel mixing atomization, fuel mixture distribution enhancement and combustion reaction enhancement are improved by unsteady plasma torch energization, integral formation of the heat exchanger, fuel injection nozzle and plasma torch anode in a more compact, low-profile arrangement which is not intrusive on a highspeed air flow with which the invention is particularly effective and further enhanced by use of nitrogen as a feedstock material and inclusion of high pressure gases in the fuel to cause effervescence during injection.

O'Brien, Walter F.↗
DOE OSTI2023

An Integrated Approach to Predicting Ash Deposition and Heat Transfer in Coal-Fired Boilers

The overall goal of this project is to develop via measurements and simulations an advanced online technology to predict, monitor and manage fireside ash deposition in a coal-fired boiler allowing for more efficient operations under a range of load conditions and fuel property variability. With this in place fuel sorting and blending can be done upstream and operations can be optimized to compensate for load and fuel properties. In support of this objective, three experimental campaigns were undertaken during the course of the project to measure ash deposition rates within the boiler at different fuel flow rates and its ash composition variability. Simulations of the experimental conditions representing actual geometry, operational scenarios in terms of air flow rates, coal flow rates as well as coal compositions, heating values, and particle size distributions were also carried out. Deposition rates were predicted using a unique particle kinetic energy and viscosity based ash deposition methodology whose validity was ascertained by comparing against deposition rate measurements for widely varying operating conditions and ash compositions in a lab-scale furnace. With a unique end-to-end combustion modeling methodology established and different simulation scenarios carried out, the results from our computational fluid dynamic (CFD) simulations in conjunction with the plant data summarized in this report were used to refine Microbeam Technology Incorporated’s MTI CSPI-CT Tool to predict and monitor fire-side ash deposition under a range of load conditions and fuel property variability in real time.

01 COAL, LIGNITE, AND PEAT↗