Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind blades”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Analysis of the National Transonic Facility mishap

The nonlinear dynamic finite element code DYnamic Crash Analysis of STructures (DYCAST) was used to model an accident scenario that occurred at the National Transonic Facility (NTF) wind tunnel. A post mishap investigation revealed that a total of five upstream bulkhead fairing plates were missing, three in one location and two in another. These plates were drawn into the wind tunnel's composite fan blades causing extensive damage. A DYCAST model was developed to determine if one-half of a small thermal shield flange clamp, weighing approximately 2.7 lbs., could have spun off the NTF drive shaft and impacted the bulkhead fairing plates with sufficient energy to cause failure of the attachment bolts. The clamp was presumed to have spun off at a tangent from the NTF drive shaft at a velocity of 1624 in/sec (drive shaft rotating at 580 rpm). The DYCAST analytical model predicts that impact of the 2.7 lbs projectile failed all of the bolts in two of the fairing plates allowing them to escape from the bulkhead ring with a low velocity of a few in/sec.

Fasanella, Edwin L.↗
NASA NTRS1990

Structural properties of laminated Douglas fir/epoxy composite material

This publication contains a compilation of static and fatigue strength data for laminated-wood material made from Douglas fir and epoxy. Results of tests conducted by several organizations are correlated to provide insight into the effects of variables such as moisture, size, lamina-to-lamina joint design, wood veneer grade, and the ratio of cyclic stress to steady stress during fatigue testing. These test data were originally obtained during development of wood rotor blades for large-scale wind turbines of the horizontal-axis (propeller) configuration. Most of the strength property data in this compilation are not found in the published literature. Test sections ranged from round cylinders 2.25 in. in diameter to rectangular slabs 6 by 24 in. in cross section and approximately 30 ft. long. All specimens were made from Douglas fir veneers 0.10 in. thick, bonded together with the WEST epoxy system developed for fabrication and repair of wood boats. Loading was usually parallel to the grain. Size effects (reduction in strength with increase in test volume) are observed in some of the test data, and a simple mathematical model is presented that includes the probability of failure. General characteristics of the wood/epoxy laminate are discussed, including features that make it useful for a wide variety of applications.

Spera, David A.↗
NASA NTRS1985

An examination of the relations between rotor vibratory loads and airframe vibrations

Harmonic rotor hub loads and airframe interactions in steady flight are reviewed, with regard to the objective of achieving lower airframe vibration by modifying blade root loads. Flight test and wind tunnel data are reviewed, along with sample fuselage response data. Trends which could provide a generalized approach to the above objective are found to be very limited. Recent analytical and corresponding experimental blade tuning modifications are reviewed and compared. Rotor vibratory load modification and substantial vibration changes were achieved over a wide range of rotor operating conditions.

Niebanck, C. F.↗
NASA NTRS1930

Test of an adjustable pitch model propeller at four blade settings

This note describes tests of an adjustable blade metal model propeller, both in a free wind stream and in combination with a model fuselage, at four settings of the blades. The model propeller is designed for a uniform nominal pitch/diameter ratio of .7 and the blade settings used correspond to nominal pitch/diameter ratios of .5, .7, .9, and 1.1 at the .6 radius. The tests show that propellers of this type may be considerably changed in setting from the designed pitch angles and yet give excellent performance. The efficiency realized and power absorbed when blades are set at other than the designed angle, are little different than would be obtained from a propeller with uniform pitch equal to the mean pitch of the propeller under test.

Lesley, E P↗
NASA NTRS1979

Wind/water energy converter

Device will convert wind, water, tidal or wave energy into electrical or mechanical energy. Is comprised of windmill-like paddles or blades synchronously geared to orient themselves to wind direction for optimum energy extraction.

Paulkovich, J.↗
NASA NTRS1995

Anechoic wind tunnel study of turbulence effects on wind turbine broadband noise

This paper describes recent results obtained at MIT on the experimental and theoretical modelling of aerodynamic broadband noise generated by a downwind rotor horizontal axis wind turbine. The aerodynamic broadband noise generated by the wind turbine rotor is attributed to the interaction of ingested turbulence with the rotor blades. The turbulence was generated in the MIT anechoic wind tunnel facility with the aid of biplanar grids of various sizes. The spectra and the intensity of the aerodynamic broadband noise have been studied as a function of parameters which characterize the turbulence and of wind turbine performance parameters. Specifically, the longitudinal integral scale of turbulence, the size scale of turbulence, the number of turbine blades, and free stream velocity were varied. Simultaneous measurements of acoustic and turbulence signals were made. The sound pressure level was found to vary directly with the integral scale of the ingested turbulence but not with its intensity level. A theoretical model based on unsteady aerodynamics is proposed.

Loyd, B.↗
NASA NTRS1994

Equations for Estimating the Strength of TV Signals Scattered by Wind Turbines

During the late 1970's and early 1980's, concerns about the potential interference of wind turbine generators with electromagnetic communication signals led to a series of research studies, both in the laboratory and in the field, conducted by the staff of the University of Michigan Radiation Laboratory. These studies were sponsored by organizations such as the U.S. Department of Energy, the Solar Energy Research Institute, and private developers of wind power stations. Research objectives were to identify the mechanisms by which wind turbines might adversely affect communication signals, estimate the severity of these effects for different types of signals (e.g. television, radio, microwave, and navigation), and formulate mathematical models with which to predict the sizes of potential interference zones around wind turbines and wind power plants. This work formed the basis for preliminary standards on assessing electromagnetic interference (EMI) by wind turbines. With the current renewal of interest in wind energy projects, it is appropriate that the many experimental and analytical aspects of this pioneering work be reviewed and correlated. The purpose of this study is to combine test data and theory from previously published and unpublished research reports into a unified and consistent set of equations which are useful for estimating potential levels of television interference from wind turbines. To be comprehensive, these equations will include both horizontal-axis and vertical-axis wind turbines (HAWT's and VAWT's), blade configuration parameters (e.g. number, size, material, twist, and coning), signal frequency and power, and directional characteristics of the receiving antenna. The approach that is followed in this report is as follows. First, some basic equations that describe electromagnetic signals with interference are presented without detailed derivations, since the latter are available in the references. Minor changes in terminology are made for purposes of consistency. Next, the concept of a signal scatter ratio is introduced, which defines the fraction of the signal impinging on a wind turbine that is scattered by its blades onto a nearby receiver. Equations from references are modified for the calculation of experimental scatter ratios (from measured signals containing interference) and idealized scatter ratios (from rotor characteristics and relative locations of the transmitter, the turbine, and the receiver). Experimental and idealized scatter ratios are then calculated and compared for 75 cases from the literature, in which TVI measurements were made around a variety of wind turbines. An empirical equation is then defined for estimating the probability that an actual scatter ratio will differ from an idealized ratio by a given amount. Finally a sample calculation of the size of a potential TV interference zone around a hypothetical wind power station is presented.

Spera, David A.↗
DOE OSTI2025

The influence of wind veer and drivetrain flexibility on fatigue loading for large floating wind turbines

To reduce costs, offshore wind turbines are expected to be designed with significantly increased rotor diameters. Larger turbines become more flexible and span a larger portion of the atmospheric boundary layer. With these changes, the validity of traditional modeling assumptions should be investigated. This work challenges two common assumptions: (1) that the drivetrain can be considered rigid (except in torsion) and does not couple with the rotor and tower and 2) that wind directional change with height (veer) does not greatly influence the fatigue damage in the tower, blades and drivetrain. Two large semi-submersible floating wind turbines are considered: a 15 and a 22 MW reference turbine. Both use direct-drive generators. Aero-hydro-servo-elastic simulations are performed using OpenFAST, with drivetrain bending flexibility and main bearing response implemented in the coupled analysis. The turbines are subjected to a set of load cases at below-, near- and above-rated mean wind speeds, assembled based on the 3 km Norwegian reanalysis (NORA3) hourly wind and wave hindcast data for Utsira Nord, off the coast of Norway. In each load case, conditions with and without veer are simulated to evaluate the influence of veer on damage equivalent loads (DELs) of the turbine tower, blades and main bearings. Further, these load cases are applied to evaluate the influence of drivetrain flexibility on aero-elastic turbine response. The results indicate that, depending on the veer gradient, mean wind speed, operating regime and turbine size, veer can be very important for tower-top DELs and the fluctuations of main bearing radial loads, while main bearing and blade-root flapwise DELs are less affected. Considering these specific load cases and turbine models, drivetrain flexibility is found to significantly influence tower-top DELs of the largest turbine: the tower-top fore-aft and torsional damage equivalent moments of the 22 MW turbine are reduced by more than 20 % at near-rated wind speeds when the drivetrain is modeled as flexible.

17 WIND ENERGY↗
NASA NTRS1988

Measurement of the steady surface pressure distribution on a single rotation large scale advanced prop-fan blade at Mach numbers from 0.03 to 0.78

The aerodynamic pressure distribution was determined on a rotating Prop-Fan blade at the S1-MA wind tunnel facility operated by the Office National D'Etudes et de Recherches Aerospatiale (ONERA) in Modane, France. The pressure distributions were measured at thirteen radial stations on a single rotation Large Scale Advanced Prop-Fan (LAP/SR7) blade, for a sequence of operating conditions including inflow Mach numbers ranging from 0.03 to 0.78. Pressure distributions for more than one power coefficient and/or advanced ratio setting were measured for most of the inflow Mach numbers investigated. Due to facility power limitations the Prop-Fan test installation was a two bladed version of the eight design configuration. The power coefficient range investigated was therefore selected to cover typical power loading per blade conditions which occur within the Prop-Fan operating envelope. The experimental results provide an extensive source of information on the aerodynamic behavior of the swept Prop-Fan blade, including details which were elusive to current computational models and do not appear in the two-dimensional airfoil data.

Bushnell, Peter↗
DOE OSTI2022

The impact of swirl and wake strength on turbulent axisymmetric wake evolution

Here, an experimental investigation of swirl and wake strength influence on axisymmetric turbulent wake evolution was conducted. A novel wake generator design wire mounted in a wind tunnel test section with low free-stream turbulence produced wake Reynolds numbers based on momentum thickness and free-stream velocity in excess of 14000 and swirl numbers up to 0.4 with minimal blockage. Steady-state blade element momentum simulations of reference wind turbine designs indicated that wind turbines operate in the flow regimes studied, indicating the practical aspects of this work. Stereoscopic particle image velocimetry was used to acquire three components of velocity in the swirling wake at locations up to approximately ten diameters downstream. Quantitative measures of wake growth and decay were deduced using available equilibrium similarity scaling for the swirling wake. The results show an increase above 50% in growth and axial velocity decay rate constants over the range of swirl strength studied compared to those of the non-swirling wake. Tangential velocity decay constants were shown to decrease with swirl strength over the range of conditions studied. Notably, changes in wake strength have little influence on growth and decay rates when compared to changes in swirl strength for the flow regimes studied in this work.

17 WIND ENERGY↗
DOE OSTI2023

OC6 project Phase III: validation of the aerodynamic loading on a wind turbine rotor undergoing large motion caused by a floating support structure

Abstract. This paper provides a summary of the work done within Phase III of the Offshore Code Comparison Collaboration, Continued, with Correlation and unCertainty (OC6) project, under the International Energy Agency Wind Technology Collaboration Programme Task 30. This phase focused on validating the aerodynamic loading on a wind turbine rotor undergoing large motion caused by a floating support structure. Numerical models of the Technical University of Denmark 10 MW reference wind turbine were validated using measurement data from a 1:75 scale test performed during the UNsteady Aerodynamics for FLOating Wind (UNAFLOW) project and a follow-on experimental campaign, both performed at the Politecnico di Milano wind tunnel. Validation of the models was performed by comparing the loads for steady (fixed platform) and unsteady (harmonic motion of the platform) wind conditions. For the unsteady wind conditions, the platform was forced to oscillate in the surge and pitch directions under several frequencies and amplitudes. These oscillations result in a wind variation that impacts the rotor loads (e.g., thrust and torque). For the conditions studied in these tests, the system aerodynamic response was almost steady. Only a small hysteresis in airfoil performance undergoing angle of attack variations in attached flow was observed. During the experiments, the rotor speed and blade pitch angle were held constant. However, in real wind turbine operating conditions, the surge and pitch variations would result in rotor speed variations and/or blade pitch actuations, depending on the wind turbine controller region that the system is operating. Additional simulations with these control parameters were conducted to verify the fidelity of different models. Participant results showed, in general, a good agreement with the experimental measurements and the need to account for dynamic inflow when there are changes in the flow conditions due to the rotor speed variations or blade pitch actuations in response to surge and pitch motion. Numerical models not accounting for dynamic inflow effects predicted rotor loads that were 9 % lower in amplitude during rotor speed variations and 18 % higher in amplitude during blade pitch actuations.

17 WIND ENERGY↗
NASA NTRS1994

Role of Wind Tunnels and Computer Codes in the Certification and Qualification of Rotorcraft for Flight in Forecast Icing

The cost and time to certify or qualify a rotorcraft for flight in forecast icing has been a major impediment to the development of ice protection systems for helicopter rotors. Development and flight test programs for those aircraft that have achieved certification or qualification for flight in icing conditions have taken many years, and the costs have been very high. NASA, Sikorsky, and others have been conducting research into alternative means for providing information for the development of ice protection systems, and subsequent flight testing to substantiate the air-worthiness of a rotor ice protection system. Model rotor icing tests conducted in 1989 and 1993 have provided a data base for correlation of codes, and for the validation of wind tunnel icing test techniques. This paper summarizes this research, showing test and correlation trends as functions of cloud liquid water content, rotor lift, flight speed, and ambient temperature. Molds were made of several of the ice formations on the rotor blades. These molds were used to form simulated ice on the rotor blades, and the blades were then tested in a wind tunnel to determine flight performance characteristics. These simulated-ice rotor performance tests are discussed in the paper. The levels of correlation achieved and the role of these tools (codes and wind tunnel tests) in flight test planning, testing, and extension of flight data to the limits of the icing envelope are discussed. The potential application of simulated ice, the NASA LEWICE computer, the Sikorsky Generalized Rotor Performance aerodynamic computer code, and NASA Icing Research Tunnel rotor tests in a rotorcraft certification or qualification program are also discussed. The correlation of these computer codes with tunnel test data is presented, and a procedure or process to use these methods as part of a certification or qualification program is introduced.

Flemming, Robert J.↗
DOE OSTI2022

Large-Eddy Simulation of a wind turbine using a Filtered Actuator Line Model

When dealing with multirotor devices such as quadcopters or wind farms, the cost of blade-resolved large-eddy simulation (LES) becomes prohibitive. Combining LES with a family of lower-fidelity models, called actuator line models (ALMs), has grown in popularity in the past decade. ALM replaces full blade resolution with an array of actuator points or lines parameterized by aerodynamic lift/drag polar plots along the blades. Body forces computed based on these actuator points are then projected onto the LES flow mesh, mimicking the effect of rotating blades on the flow. However, the optimal projection radius and the associated LES grid size is often too restrictive for multirotor simulations. Recently, a new tip-correction-based filtered ALM (F-ALM) was proposed by Martinez-Tossas and Meneveau (2019), which allows coarser-than-optimal grids by avoiding the associated overprediction of thrust. In this work, F-ALM is implemented into a high-order, in-house LES code to simulate National Renewable Energy Laboratory Phase VI wind turbine. It is then followed by a comparison between the baseline ALM and the newly implemented F-ALM in terms of instantaneous and time-averaged flow fields and blade loads, revealing the advantages of F-ALM in preventing the overprediction of power on coarse grids. Finally, this encourages accurate and affordable simulations of multirotor devices in the future.

17 WIND ENERGY↗
NASA NTRS2012

Determination of HART I Blade Structural Properties by Laboratory Testing

The structural properties of higher harmonic Aeroacoustic Rotor Test (HART I) blades were measured using the original set of blades tested in the German-dutch wind tunnel (DNW) in 1994. the measurements include bending and torsion stiffness, geometric offsets, and mass and inertia properties of the blade. the measured properties were compared to the estimated values obtained initially from the blade manufacturer. The previously estimated blade properties showed consistently higher stiffness, up to 30 percent for the flap bending in the blade inboard root section.

Jung, Sung N.↗
NASA NTRSDate not supplied

Blade Mistuning Analysis for Boundary Layer Inlet Flow Distortion-Tolerant Fan Blades

NASA Glenn Research Center has tested the BLI2DTF propulsor including the fan rotor. BLI2DTF stands for Boundary Layer Ingesting Inlet/Distortion-Tolerant Fan. A comparison of the vibratory response between analysis results and experimental wind tunnel test results yielded reasonable agreement, yet some differences were noted. Blade mistuning effects have been identified as a potential cause for these differences. A tuned forced response analysis in a turbomachinery engine rotor system assumes that all of the blades are identical, so that the natural frequencies of individual blades are the same. In contrast to this assumption, the wind tunnel tests of the BLI2DTF rotor system revealed that the individual blade response frequencies varied. These variations in individual blade frequencies may be attributed to blade mistuning due to potential differences in the structural and material properties of individual blades. For an understanding of these variations, it is necessary to analyze the influence of blade mistuning on the BLI2DTF rotor system, which will provide a more precise assessment of its vibratory stresses and high cycle fatigue life. The purpose of the study was to investigate the influence of blade mistuning on the dynamic characteristics of this rotor system. At the same fan operation condition, a comparative forced response analysis was performed for both tuned and mistuned BLI2DTF rotor systems. A comparison of the results from these analyses found that the mistuning effects on the present BLI2DTF rotor system are notable. As a result, fan blade mistuning is to be considered a contributor to the levels of vibratory dynamic stresses observed during the wind tunnel experiment.

Blade mistuning↗
NASA NTRS1974

Low-speed wind tunnel tests of a 50.8-centimeter (20-in.) 1.15-pressure-ratio fan engine model

At a typical STOL aircraft takeoff and landing velocity, wind tunnel aerodynamic and acoustic measurements demonstrated that an inlet lip-area contraction ratio of 1.35 was superior to a ratio of 1.26 at high incidence angles. A 17 percent reduction in net thrust and an increase of 9 decibels in sound pressure level at the blade passing frequency resulted from inlet flow separation at an incidence angle of 50 deg with the 1.26-contraction-ratio inlet. Reverse-thrust forces obtained with blade rotation through the feathered angle were 1.8 times larger than with blade rotation through the flat angle. Reverse-thrust force was reduced from 30 to 50 percent and sound pressure level increased from 3 to 7 decibels at the blade passing frequency between the wind-tunnel-off condition and a typical STOL aircraft landing velocity.

Wesoky, H. L.↗