SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Solid rocket engine propellant grain structural dynamics including elastic and viscoelastic deformations, stress and shear vibration modes, natural frequency calculations, etc, using Fourier inversions and transforms
Friction factors and velocity profiles in turbulent flow of viscoelastic non-Newtonian fluid, noting correlation between frictional characteristics and Reynolds number
Fracture in viscoelastic bodies, considering stress-strain-time properties and analyzing temperature and failure envelopes
Cassini will be protected during launch ascent through the atmosphere by a lightweight aluminum payload fairing (PLF). As a result of the extreme noise levels generated by the powerful Titan IV at liftoff, and the acoustic transparency of the PLF, Cassini is predicted to experience severe acoustic levels. Furthermore, the high acoustic levels, coupled with the size and configuration of the spacecraft, will induce intense random vibration on the structure and critical spacecraft components. Efforts to mitigate the vibroacoustic environment by modifying the spacecraft structure were pursued. Preliminary studies indicated that a structural damping treatment using viscoelastic materials (VEMs) represented a viable technique of reducing vibration with minimum impact on weight, cost, and redesign. Tuned Vibration Absorbers (TVAs) - compact, single degree-of-freedom mechanical oscillators in which a VEM serves as the spring and damping element - will be used also. The operating principles, design, and installation of the TVAs are described, the test program is outlined, and test results are presented which show that significant vibration attenuation was achieved.
A series of mechanical tests were conducted on a high-conductivity copper alloy, GRCop-84, in order to understand the time dependent response of this material. Tensile, creep, and stress relaxation tests were performed over a wide range of temperatures, strain rates, and stress levels to excite various amounts of time-dependent behavior. At low applied stresses the deformation behavior was found to be fully reversible. Above a certain stress, termed the viscoelastic threshold, irreversible deformation was observed. At these higher stresses the deformation was observed to be viscoplastic. Both reversible and irreversible regions contained time dependent deformation. These experimental data are documented to enable characterization of constitutive models to aid in design of high temperature components.
Composites structures are widely used in aerospace and wind energy applications for their excellent stiffness and strength-to-weight properties. In these structures, structural damping is critical to predict vibration amplitudes, performance, and reliability. Structural damping is of particular interest for slender wings, rotorcraft blades, and wind turbine blades that can exhibit complex vibration phenomena and are frequently modeled with geometrically exact beam theory (GEBT). Standard approaches of stiffness proportional or modal damping merely assign user defined values and cannot predict damping behavior. This work compares stiffness proportional damping to two more advanced damping approaches: modal strain energy and Prony series. The modal strain energy approach uses a sectional analysis tool to calculate the beam stiffness and postprocess internal stresses from GEBT simulations. The internal stresses are then used to calculate modal damping factors. The Prony series is implemented within GEBT to directly model viscoelastic behavior of the composites. These approaches are compared by modeling the evolution of the damping factors of a realistic flexible wind turbine blade with varying rotational speed. Discrepancies between the approaches suggest areas for future modeling development, but differences in nonlinear damping values are less than current uncertainties about the magnitude of structural damping.
Wearable devices benefit from the use of stretchable conjugated polymers (CPs). Traditionally, the design of stretchable CPs is based on the assumption that a low elastic modulus (E) is crucial for achieving high stretchability. However, this research, which analyzes the mechanical properties of 65 CP thin films, challenges this notion. It is discovered that softness alone does not determine stretchability; rather, it is the degree of entanglement that is critical. This means that rigid CPs can also exhibit high stretchability, contradicting conventional wisdom. To inverstigate further, the mechanical behavior, electrical properties, and deformation mechanism of two model CPs: a glassy poly(3-butylthiophene-2,5-diyl) (P3BT) with an E of 2.2 GPa and a viscoelastic poly(3-octylthiophene-2,5-diyl) (P3OT) with an E of 86 MPa, are studied. Ex situ transmission X-ray scattering and polarized UV–vis spectroscopy revealed that only the initial strain (i.e., <20%) exhibits different chain alignment mechanisms between two polymers, while both rigid and soft P3ATs showed similarly behavior at larger strains. In conclusion, by challenging the conventional design metric of low E for high stretchability and highlighting the importance of entanglement, it is hoped to broaden the range of CPs available for use in wearable devices.
Covalent adaptable networks (CANs) offer a compelling strategy to unite the mechanical robustness of thermosets with the reprocessability of thermoplastics, yet achieving simultaneous durability, processability, and true recyclability remains challenging. We introduce diketoenamine (DKE) vitrimers derived from β-triketone methacrylate monomers and demonstrate how rational monomer design dictates network processability, viscoelasticity, and recyclability. By systematically varying the spacer length between the β-triketone (TK) moiety and the polymer backbone, we identify a key structure–property relationship that dictates vitrimer behavior. Networks bearing TK pendants minimally displaced from the backbone suppress creep but exhibit limited stress relaxation, whereas extended spacers yield lower glass transition temperatures, higher effective crosslink densities, and efficient stress dissipation, enabling optical transparency and reprocessability. Extending this platform to ultra-high molecular-weight prepolymers introduces physical entanglements as secondary crosslinks, further enhancing dimensional stability without compromising processability. Both mechanical and chemical recycling validate the closed-loop circularity of these materials. Furthermore, these results establish TK methacrylates as a versatile platform for designing high-performance vitrimers that integrate durability, reprocessability, and true closed-loop recyclability.
Recent developments in additive manufacturing (AM) of glass via silica-filled inks have facilitated fabrication of previously unattainable geometries and compositions. However, the maximum processable size of 15 mm limits the use of these prints in applications such as optics. A key limitation lies in the trade-off between material printability and green strength: increasing silica content in the feedstock improves crack resistance and reduces shrinkage but results in dramatic changes in viscoelastic properties that hinder flowability. Here, this paper presents a novel approach that offers expanded versatility in processable size, feedstock formulation, and printing. Described here is a direct ink writing (DIW) system coupled with an active high-shear micromixer and UV light source, capable of simultaneously printing multiple inks with a wide range of rheological properties. Choice of silica sourc, solvent, UV-curable binder, and dispersant is used to tune the ink rheology and improve printability and mechanical properties. Imparting high shear with the micromixer while UV-curing the extrudate allows for increased ink viscosities and reduced nozzle diameters, enabling printing finer feature sizes. With these advances, thin-walled high-aspect ratio structures and a crack-free glass disk measuring 44 mm in diameter are demonstrated, an increase of 3× in the greatest dimension compared to current state-of-the-art.
Reconfigurable microdevices are being explored in a range of contexts where their life-like abilities to move and change shape are important. While much work has been done to control the motion of these microdevices by engineering their geometry and composition, little is known about their dynamics in complex fluid environments with non-Newtonian rheology. Here in this paper, it is shown how the actuation dynamics of reconfigurable microdevices made by assembly of patchy magnetic microcubes, which are referred to as “microbots,” can be modulated by their interactions with the anisotropic viscoelastic environment of a liquid crystal (LC). The free energy arising from the elastic strain of LC and formation of topological defects around the microbots influences their folding dynamics, which can be tuned by tailoring both the far-field orientation of the LC and the local ordering of the LC at the microbot surfaces. These findings represent a first step toward establishing a general set of design rules to control the dynamics of microbots using complex anisotropic fluids.
Abstract Biomaterials such as spider silk and mussel byssi are fabricated by the dynamic manipulation of intra‐ and intermolecular biopolymer interactions. Organisms modulate solution parameters, such as pH and ion co‐solute concentration, to effect these processes. These biofabrication schemes provide a conceptual framework to develop new dynamic and responsive abiotic soft material systems. Towards these ends, the chemical diversity of readily available ionic compounds offers a broad palette to manipulate the physicochemical properties of polyelectrolytes via ion‐specific interactions. In this study, we show for the first time that the ion‐specific interactions of biomimetic polyelectrolytes engenders a variety of phase separation behaviors, creating dynamic thermal‐ and ion‐responsive soft matter that exhibits a spectrum of physical properties, spanning viscous fluids to viscoelastic and viscoplastic solids. These ion‐dependent characteristics are further rendered general by the merger of lysine and phenylalanine into a single, amphiphilic vinyl monomer. The unprecedented breadth, precision, and dynamicity in the reported ion‐dependent phase behaviors thus introduce a broad array of opportunities for the future development of responsive soft matter; properties that are poised to drive developments in critical areas such as chemical sensing, soft robotics, and additive manufacturing.
Segmented polyureas (PUa) are industrially important class of polymers widely used in coatings, sealant, and adhesive applications. Here, in this paper, we report synthesis, characterization, and modeling of Isophorone Diisocyanate-Diethyl-Toluene-Diamine-Polyether amine (IPDI-DETDA-PO PUa) with varied hard segment contents of 20, 30, and 40 weight percent. For each of the three materials, we study its structure and phase behavior using FTIR, DSC, and TEM, and clearly show the presence of microphase separation between the hard and soft nanodomains. We then measure the linear viscoelastic response of the PUa-s using DMA (frequency sweeps at multiple temperatures). The DMA data are shown to obey the time-temperature superposition. Finally, we develop a new micromechanical model describing the DMA results; the model describes a phase-separated PUa as two “Fractional-order Maxwell gels” branches, connected in parallel, with the first FMG branch representing the “percolated hard phase" and the second one modeling the “filled soft phase". In agreement with the earlier thermodynamic theories, the volume-fraction of the percolated hard phase is related to the hard segment weight-fraction (HSWF), defined as the combined mass of IPDI and DETDA normalized to the total mass of the polymer. The data and model are found to be in a good qualitative and quantitative agreement.
Abstract Dynamic liquid crystalline polymers (dLCPs) incorporate both liquid crystalline mesogens and dynamic bonds into a single polymeric material. These dual functionalities impart order‐dependent thermo‐responsive mechano‐optical properties and enhanced reprocessability/programmability enabling their use as soft actuators, adaptive adhesives, and damping materials. While many previous works studying dynamic LCPs utilize dynamic covalent bonds, metallosupramolecular bonds provide a modular platform where a series of materials can be accessed from a single polymeric feedstock through the variation of the metal ion used. A series of dLCPs were prepared by the addition of metal salts to a telechelic 2,6‐bisbenzimidazolylpyridine (Bip) ligand endcapped LCP to form metallosupramolecular liquid crystal polymers (MSLCPs). The resulting MSLCPs were found to phase separate into hard and soft phases which aids in their mechanical robustness. Variations of the metal salts used to access these materials allowed for control of the thermomechanical, viscoelastic, and adhesive properties with relaxations that can be tailored independently of the mesogenic transition. This work demonstrates that by accessing phase separation through the incorporation of metallosupramolecular moieties, highly processable yet robust MSLCP materials can be realized. This class of materials opens the door to LCPs with bulk flow behavior that can also be utilized as multi‐level adhesives.
One-dimensional site response analysis (1D SRA) remains the standard practice in considering the effect of local soil deposits and predicting site-specific ground motions, although its range of applicability to realistic seismic wavefields is still in question. In this 1D approach, horizontal and vertical ground shaking are assumed to be induced by vertically propagating shear and compressional waves, respectively. A recent study based on analytical two-dimensional (2D) plane waves and simple point source earthquake simulations has shown two mechanistic limitations in this 1D modelling technique for general inclined seismic waves, that is, systematic over-prediction of the vertical motion and wave trapping in the 1D soil column. In this article, we evaluate in detail the applicability of this 1D modelling approach to realistic three-dimensional (3D) simulated seismic wavefields in shallow sedimentary basins. Linear-viscoelastic 1D SRA predictions using two types of input motions that are commonly used in practice—rock outcrop and in-column motions, are compared with the reference true site response results from 3D earthquake simulations in terms of various measures in the frequency and time domain. It is shown that the horizontal motion in the 3D seismic wavefield exhibits dominant shear wave propagation phenomenon, while the vertical motion is a combined effect of compressional and shear waves and can be over-predicted by the 1D approach when the incident seismic waves are inclined. Direct evidence of the wave refraction process that leads to the vertical motion over-prediction is provided. 1D SRA with in-column inputs can yield motions that have significantly longer duration compared to the true 3D site response solution due to trapped waves, casting in doubt the frequent need for increased soil damping in existing site studies to compensate for wave attenuation due to scattering alone. Sensitivity investigation on the increase of soil profile damping by a multiplier D mul shows D mul values compatible with those found in the literature for both horizontal and vertical motions. It is shown that the level of D mul optimized for a best match of the spectral acceleration is dependent on the characteristic of the input motion and a larger D mul is typically required for the vertical component. In contrast, 1D SRA with outcrop motions predicts motions with shorter significant duration due to its inability to capture the basin-edge generated surface waves. A suite of ground motion simulations was performed to assess the sensitivity of the observations to the basin geologic structure including the velocity gradient, rock-basin impedance contrast and basin depth. The analysis results show that the accuracy of the simplified 1D procedure is dependent on the wavefield composition of both the input motions and the true 3D site response solution. While the horizontal motions in shallow sedimentary basins can, to the first order, be reasonably captured by the simplified 1D approach, 1D SRA for the vertical component is in general not reliable and contributions from inclined shear waves should be accounted for in site-specific evaluation of the vertical design ground motion.
ABSTRACT Biohybrids (BHs)based on bentonite and anthocyanins can be produced as alternatives to synthetic colorants. However, no information is available on the interaction of biohybrid with food system. This research studies the rheological properties of gummies containing k‐carrageenan and xanthan gum incorporated with a BH. The incorporation of BH (≤ 2% w/w) increased the flow consistency index and shear thinning effect in melted gummies at 85°C. During cooling from 90°C to 25°C, the presence of BH altered the sol–gel transition temperature typical in carrageenan systems, probably by the formation of carrageenan complexes. At 25°C, all gummies had a solid‐like response with elastic modulus ( G ') higher than viscous modulus ( G "). G ' values increased linearly with BH concentration, and the linear viscoelastic region and breaking strain decreased with BH concentration, indicating that this natural additive acted as a reinforcing material.
Abstract We investigate the effect of alcohol fraction (isopropanol, IPA) in a binary water‐alcohol solvent mixture on the shear and extensional rheological properties, as well as the role of viscoelasticity on fiber formation of poly(acrylic acid) (PAA) in electrospinning. Comparison of the scaling of both specific viscosities η sp and extensional relaxation times λ E of PAA in water–IPA mixtures, showed stronger scaling compared to salt‐free aqueous polyelectrolyte solutions, except for the η sp in the unentangled regime displaying a polyelectrolyte‐like scaling η sp ~ c 0.5 for all IPA%. Such deviation suggested IPA induces association/aggregation of PAA. However, the trends between η sp and λ E magnitudes as a function of IPA% differ for concentrations compared in the entangled regime. The η sp as well as their elastic moduli exhibit a maximum, whereas λ E increases monotonically with IPA%, suggesting a complex interplay of various interactions are dictating their structure in water‐IPA mixtures, affecting their shear and extensional response differently. Electrospinning experiments showed increasing IPA% reduces the onset of both beaded and uniform fibers. Analysis using dimensionless numbers indicated the enhancement of their elasticity by IPA, and the consequent stabilizing effect on their jets/filaments against break‐up during electrospinning, plays a role in the improvement of their fiber formation.
The paper addresses the role of crystal anisotropy on the evolution of heterogeneous temperature fields in plastic-bonded explosives (PBXs) under conditions of weak shock. The modeling approach is based on simplified idealizations of PBX microstructure including RDX grains and estane binder regions subjected to velocity boundary conditions representative of impact conditions in situ. The constitutive description of the microstructure constituents includes a dislocation-based, anisotropic, single crystal plasticity model for the explosive grains and a linear viscoelastic model to represent the estane binder. Large suites of simulations were used to systematically study the correlation in heating of the grains with local wave dynamics, crystal orientation, and the microstructural neighborhood. These correlations were identified through the selection of characteristics of crystal anisotropy including oriented wave speeds and Taylor factor. A key observation is that the wave dispersion within a certain distance from the impact interface plays a dominant role in the temperature field. Beyond this distance, individual crystal orientations play a more dominant role, but cannot entirely account for the observed heterogeneity without consideration of the local microstructure neighborhood.
Abstract This paper develops a deep learning tool based on neural processes (NPs) called the Peri-Net-Pro, to predict the crack patterns in a moving disk and classifies them according to the classification modes with quantified uncertainties. In particular, image classification and regression studies are conducted by means of convolutional neural networks (CNNs) and NPs. First, the amount and quality of the data are enhanced by using peridynamics to theoretically compensate for the problems of the finite element method (FEM) in generating crack pattern images. Second, case studies are conducted with the prototype microelastic brittle (PMB), linear peridynamic solid (LPS), and viscoelastic solid (VES) models obtained by using the peridynamic theory. The case studies are performed to classify the images by using CNNs and determine the suitability of the PMB, LBS, and VES models. Finally, a regression analysis is performed on the crack pattern images with NPs to predict the crack patterns. The regression analysis results confirm that the variance decreases when the number of epochs increases by using the NPs. The training results gradually improve, and the variance ranges decrease to less than 0.035. The main finding of this study is that the NPs enable accurate predictions, even with missing or insufficient training data. The results demonstrate that if the context points are set to the 10th, 100th, 300th, and 784th, the training information is deliberately omitted for the context points of the 10th, 100th, and 300th, and the predictions are different when the context points are significantly lower. However, the comparison of the results of the 100th and 784th context points shows that the predicted results are similar because of the Gaussian processes in the NPs. Therefore, if the NPs are employed for training, the missing information of the training data can be supplemented to predict the results.