Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “variable selection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

A parametric study of planform and aeroelastic effects on aerodynamic center, alpha- and q-stability derivatives

Summarized are the aerodynamic center, alpha and q- aeroelastic effects on fighter-type aircraft in the 18,700 N gross range. The results indicate that with proper tailoring of planform (fixed or variable sweep), stiffner and elastic axis location it is possible to minimize trim requirements between selected extreme conditions. The inertial effects were found to be small for this class of aircraft.

Roskam, J.↗
NASA NTRS1976

Performance, emissions, and physical characteristics of a rotating combustion aircraft engine

The RC2-75, a liquid cooled two chamber rotary combustion engine (Wankel type), designed for aircraft use, was tested and representative baseline (212 KW, 285 BHP) performance and emissions characteristics established. The testing included running fuel/air mixture control curves and varied ignition timing to permit selection of desirable and practical settings for running wide open throttle curves, propeller load curves, variable manifold pressure curves covering cruise conditions, and EPA cycle operating points. Performance and emissions data were recorded for all of the points run. In addition to the test data, information required to characterize the engine and evaluate its performance in aircraft use is provided over a range from one half to twice its present power. The exhaust emissions results are compared to the 1980 EPA requirements. Standard day take-off brake specific fuel consumption is 356 g/KW-HR (.585 lb/BHP-HR) for the configuration tested.

Berkowitz, M.↗
NASA NTRS1979

Decoupling control of a long flexible beam in orbit

The paper presents a method of control for large flexible systems using state variable feedback, with a long flexible beam given as an example. These feedback gains are selected: (1) based on the decoupling of the original coordinates and to obtain proper damping and (2) by applying the linear regulator problem to the individual modal coordinates separately. It is shown that the linear control law thus obtained are then evaluated by numerical integration of the non-linear system equations. Also included are results showing the effects (control spillover) on the uncontrolled modes when the number of controllers is less than the number of modes, and the effects of inaccurate knowledge of the control influence coefficients which lead to errors in the calculated feedback gains.

Reddy, A. S. S. R.↗
NASA NTRS1981

VTOL as it applies to resource development in the Canadian north

It is pointed out that, for many of the natural resource development projects planned in Canada between now and the end of the century, it may be necessary for the work force to commute to the site by air. Examples of successful operations, including those involving VTOL, are given. A computer program developed for determining the least expensive type of aircraft for commuting to remote projects is described. It is noted that the program can select both fixed-wing and helicopter aircraft types for a specific project, employing such variables as the size and shift schedules of the work force and the commuting distance. Capital and operating costs of existing and proposed aircraft types, as well as groundside infrastructure operations and maintenance costs, are compared for competing aircraft.

Lightfoot, R. N.↗
NASA NTRS1984

A simulation of remote sensor systems and data processing algorithms for spectral feature classification

A computational model of the deterministic and stochastic processes involved in multispectral remote sensing was designed to evaluate the performance of sensor systems and data processing algorithms for spectral feature classification. Accuracy in distinguishing between categories of surfaces or between specific types is developed as a means to compare sensor systems and data processing algorithms. The model allows studies to be made of the effects of variability of the atmosphere and of surface reflectance, as well as the effects of channel selection and sensor noise. Examples of these effects are shown.

Arduini, R. F.↗
NASA NTRS1985

Extraction of information from major element chemical analyses of lunar basalts

Major element chemical analyses often form the framework within which similarities and differences of analyzed specimens are noted and used to propose or devise models. When percentages are formed the ratios of pairs of components are preserved whereas many familiar statistical and geometrical descriptors are likely to exhibit major changes. This ratio preserving aspect forms the basis for a proposed framework. An analysis of compositional variability within the data set of 42 major element analyses of lunar reference samples was selected to investigate this proposal.

Butler, J. C.↗
NASA NTRS1986

Sensitivity analysis and approximation methods for general eigenvalue problems

Optimization of dynamic systems involving complex non-hermitian matrices is often computationally expensive. Major contributors to the computational expense are the sensitivity analysis and reanalysis of a modified design. The present work seeks to alleviate this computational burden by identifying efficient sensitivity analysis and approximate reanalysis methods. For the algebraic eigenvalue problem involving non-hermitian matrices, algorithms for sensitivity analysis and approximate reanalysis are classified, compared and evaluated for efficiency and accuracy. Proper eigenvector normalization is discussed. An improved method for calculating derivatives of eigenvectors is proposed based on a more rational normalization condition and taking advantage of matrix sparsity. Important numerical aspects of this method are also discussed. To alleviate the problem of reanalysis, various approximation methods for eigenvalues are proposed and evaluated. Linear and quadratic approximations are based directly on the Taylor series. Several approximation methods are developed based on the generalized Rayleigh quotient for the eigenvalue problem. Approximation methods based on trace theorem give high accuracy without needing any derivatives. Operation counts for the computation of the approximations are given. General recommendations are made for the selection of appropriate approximation technique as a function of the matrix size, number of design variables, number of eigenvalues of interest and the number of design points at which approximation is sought.

Murthy, D. V.↗
NASA NTRS1988

Liquid rocket boosters for the Space Shuttle - An outline of trade issues and analysis techniques

Numerous liquid rocket booster configurations were studied to replace the Solid Rocket Boosters on the current Space Shuttle. While improved safety, reliability, performance and economy of operation were sought, the designs also sought to minimize volumetric growth to reduce aerodynamic loads and structural modifications. Aero loads could be significant as a function of booster diameter if extrapolated directly from solid rocket characteristics. Procedures to meet these goals with analytical booster sizing and simple dynamic simulations are shown. Engine chamber pressure proved to be a good independent variable for implications of pressure-fed and pump-fed engines, fuel and material selection. For some configurations, ascent trajectory modifications were suggested: longer vertical rise, lofting, heads-up orientation, and higher first and second stage target altitudes. Since engine manufacture would dominate booster costs, booster simplification of reuse are discussed based on cost estimates.

Kelly, W. D.↗
NASA NTRS1990

High galactic latitude cataclysmic variables

A sample of stars which are either known or are good candidates for being halo cataclysmic variables has been isolated. This sample consists of 84 stars of which 57 are dwarf novae (two of these are probable DQ Her systems), 12 are novalike stars, seven are AM Her objects, and eight are classical novae. Periodicities are known for 27 of the systems. If these stars are indeed halo members, then their distances range from 350 pc to 8 kpc and they represent objects that should be significantly older than their disk counterparts. If they do not represent true halo members, then they are intrinsically very faint systems (Mv greater than +10). Comparing the gross properties of this sample to those for the disk cataclysmic variables, it is found that below the period gap, the mean outburst amplitude for the halo dwarf novae is 3 mag greater than for the disk dwarf novae. For systems with periods less than 4 h, the halo cataclysmic variables have a higher percentage of systems below the period gap than the disk cataclysmic variables. The implications of these findings are discussed, as well as possible sample biases and selection effects.

Howell, Steve B.↗
NASA NTRS1991

Quasi-perpendicular/quasi-parallel divisions of earth's bow shock

Computer-drawn diagrams of the boundaries between quasi-perpendicular and quasi-parallel areas of earth's bow shock are displayed for a few selected cone angles of static interplanetary magnetic field (IMF). The effect on the boundary of variable IMF in the foreshock is also discussed and shown for one nominal case. The boundaries demand caution in applying them to the realistic, dynamic conditions of the solar wind and in interpreting the effects of small cone angles on the distributions of structures at the shock. However, the calculated, first-order boundaries are helpful in defining areas of the shock where contributions from active structures inherent in quasi-parallel geometry may be distinguishable from those derived secondarily from upstream reflected ion dynamics. The boundaries are also compatible with known behavior of daytime ULF geomagnetic waves and pulsations according to models postulating that cone angle-controlled, time-dependent ULF activity around the subsolar point of the bow shock provides the source of geomagnetic excitation.

Greenstadt, E. W.↗
NASA NTRS1994

Optimization of Orifice Geometry for Cross-Flow Mixing in a Cylindrical Duct

Mixing of gaseous jets in a cross-flow has significant applications in engineering, one example of which is the dilution zone of a gas turbine combustor. Despite years of study, the design of jet injection in combustors is largely based on practical experience. A series of experiments was undertaken to delineate the optimal mixer orifice geometry. A cross-flow to core-flow momentum-flux ratio of 40 and a mass flow ratio of 2.5 were selected as representative of an advanced design. An experimental test matrix was designed around three variables: the number of orifices, the orifice aspect ratio (long-to-short dimension), and the orifice angle. A regression analysis was performed on the data to arrive at an interpolating equation that predicted the mixing performance of orifice geometry combinations within the range of the test matrix parameters. Results indicate that mixture uniformity is a non-linear function of the number of orifices, the orifice aspect ratio, and the orifice angle. Optimum mixing occurs when the asymptotic mean jet trajectories are in the range of 0.35 less than r/R less than 0.5 (where r = 0 is at the mixer wall) at z/R = 1.0. At the optimum number of orifices, the difference between shallow-angled slots with large aspect ratios and round holes is minimal and either approach will lead to good mixing performance. At the optimum number of orifices, it appears possible to have two local optimums where one corresponds to an aspect ratio of 1.0 and the other to a high aspect ratio.

Sowa, W. A.↗
NASA NTRS1996

Optimization of Orifice Geometry for Cross-Flow Mixing in a Cylindrical Duct

Mixing of gaseous jets in a cross-flow has significant applications in engineering, one example of which is the dilution zone of a gas turbine combustor. Despite years of study, the design of the jet injection in combustors is largely based on practical experience. The emergence of NO(x) regulations for stationary gas turbines and the anticipation of aero-engine regulations requires an improved understanding of jet mixing as new combustor concepts are introduced. For example, the success of the staged combustor to reduce the emission of NO(x) is almost entirely dependent upon the rapid and complete dilution of the rich zone products within the mixing section. It is these mixing challenges to which the present study is directed. A series of experiments was undertaken to delineate the optimal mixer orifice geometry. A cross-flow to core-flow momentum-flux ratio of 40 and a mass flow ratio of 2.5 were selected as representative of a conventional design. An experimental test matrix was designed around three variables: the number of orifices, the orifice length-to- width ratio, and the orifice angle. A regression analysis was performed on the data to arrive at an interpolating equation that predicted the mixing performance of orifice geometry combinations within the range of the test matrix parameters. Results indicate that the best mixing orifice geometry tested involves eight orifices with a long-to-short side aspect ratio of 3.5 at a twenty-three degree inclination from the center-line of the mixing section.

Kroll, J. T.↗
NASA NTRS2002

Tropospheric Ozone during the TRACE-P Mission: Comparison between TOMS Satellite Retrievals and Aircraft Lidar Data, March 2001

Over the past several years, we have developed two new tropospheric ozone retrievals from the TOMS (Total Ozone Mapping Spectrometer) satellite instrument that are of sufficient resolution to follow pollution episodes. The modified-residual technique uses v. 7 TOMS total ozone and is applicable to tropical regimes in which the wave-one pattern in total ozone is observed. The TOMS-direct method ('TDOT' = TOMS Direct Ozone in the Troposphere) represents a new algorithm that uses TOMS radiances directly to extract tropospheric ozone in regions of constant stratospheric ozone. It is not geographically restricted, using meteorological regimes as the basis for classifying TOMS radiances and for selecting appropriate comparison data. TDOT is useful where tropospheric ozone displays high mixing ratios and variability characteristic of pollution. Some of these episodes were observed downwind of Asian biomass burning during the TRACE-P (Transport and Atmospheric Chemical Evolution-Pacific) field experiment in March 2001. This paper features comparisons among TDOT tropospheric ozone column depth, integrated uv-DIAL measurements made from NASA's DC-8, and ozonesonde data.

Frolov, A. D.↗
NASA NTRS2006

"One-Stop Shopping" for Ocean Remote-Sensing and Model Data

OurOcean Portal 2.0 (http:// ourocean.jpl.nasa.gov) is a software system designed to enable users to easily gain access to ocean observation data, both remote-sensing and in-situ, configure and run an Ocean Model with observation data assimilated on a remote computer, and visualize both the observation data and the model outputs. At present, the observation data and models focus on the California coastal regions and Prince William Sound in Alaska. This system can be used to perform both real-time and retrospective analyses of remote-sensing data and model outputs. OurOcean Portal 2.0 incorporates state-of-the-art information technologies (IT) such as MySQL database, Java Web Server (Apache/Tomcat), Live Access Server (LAS), interactive graphics with Java Applet at the Client site and MatLab/GMT at the server site, and distributed computing. OurOcean currently serves over 20 real-time or historical ocean data products. The data are served in pre-generated plots or their native data format. For some of the datasets, users can choose different plotting parameters and produce customized graphics. OurOcean also serves 3D Ocean Model outputs generated by ROMS (Regional Ocean Model System) using LAS. The Live Access Server (LAS) software, developed by the Pacific Marine Environmental Laboratory (PMEL) of the National Oceanic and Atmospheric Administration (NOAA), is a configurable Web-server program designed to provide flexible access to geo-referenced scientific data. The model output can be views as plots in horizontal slices, depth profiles or time sequences, or can be downloaded as raw data in different data formats, such as NetCDF, ASCII, Binary, etc. The interactive visualization is provided by graphic software, Ferret, also developed by PMEL. In addition, OurOcean allows users with minimal computing resources to configure and run an Ocean Model with data assimilation on a remote computer. Users may select the forcing input, the data to be assimilated, the simulation period, and the output variables and submit the model to run on a backend parallel computer. When the run is complete, the output will be added to the LAS server for

Li, P. Peggy↗
NASA NTRS2005

NASA Tech Briefs, July 2005

Thin-Film Resistance Heat-Flux Sensors Circuit Indicates that Voice-Recording Disks are Nearly Full Optical Sensing of Combustion Instabilities in Gas Turbines Topics include: Crane-Load Contact Sensor; Hexagonal and Pentagonal Fractal Multiband Antennas; Multifunctional Logic Gate Controlled by Temperature; Multifunctional Logic Gate Controlled by Supply Voltage; Power Divider for Waveforms Rich in Harmonics; SCB Quantum Computers Using iSWAP and 1-Qubit Rotations; CSAM Metrology Software Tool; Update on Rover Sequencing and Visualization Program; Selecting Data from a Star Catalog; Rotating Desk for Collaboration by Two Computer Programmers; Variable-Pressure Washer; Magnetically Attached Multifunction Maintenance Rover; Improvements in Fabrication of Sand/Binder Cores for Casting; Solid Freeform Fabrication of Composite-Material Objects; Efficient Computational Model of Hysteresis; Gauges for Highly Precise Metrology of a Compound Mirror; Improved Electrolytic Hydrogen Peroxide Generator; High-Power Fiber Lasers Using Photonic Band Gap Materials; Ontology-Driven Information Integration; Quantifying Traversability of Terrain for a Mobile Robot; More About Arc-Welding Process for Making Carbon Nanotubes; Controlling Laser Spot Size in Outer Space; or Software-Reconfigurable Processors for Spacecraft.

Source record↗
NASA NTRS2014

A Generic Nonlinear Aerodynamic Model for Aircraft

A generic model of the aerodynamic coefficients was developed using wind tunnel databases for eight different aircraft and multivariate orthogonal functions. For each database and each coefficient, models were determined using polynomials expanded about the state and control variables, and an othgonalization procedure. A predicted squared-error criterion was used to automatically select the model terms. Modeling terms picked in at least half of the analyses, which totalled 45 terms, were retained to form the generic nonlinear aerodynamic (GNA) model. Least squares was then used to estimate the model parameters and associated uncertainty that best fit the GNA model to each database. Nonlinear flight simulations were used to demonstrate that the GNA model produces accurate trim solutions, local behavior (modal frequencies and damping ratios), and global dynamic behavior (91% accurate state histories and 80% accurate aerodynamic coefficient histories) under large-amplitude excitation. This compact aerodynamics model can be used to decrease on-board memory storage requirements, quickly change conceptual aircraft models, provide smooth analytical functions for control and optimization applications, and facilitate real-time parametric system identification.

Grauer, Jared A.↗
NASA NTRS1992

Maximum life spiral bevel reduction design

Optimization is applied to the design of a spiral bevel gear reduction for maximum life at a given size. A modified feasible directions search algorithm permits a wide variety of inequality constraints and exact design requirements to be met with low sensitivity to initial values. Gear tooth bending strength and minimum contact ratio under load are included in the active constraints. The optimal design of the spiral bevel gear reduction includes the selection of bearing and shaft proportions in addition to gear mesh parameters. System life is maximized subject to a fixed back-cone distance of the spiral bevel gear set for a specified speed ratio, shaft angle, input torque, and power. Significant parameters in the design are: the spiral angle, the pressure angle, the numbers of teeth on the pinion and gear, and the location and size of the four support bearings. Interpolated polynomials expand the discrete bearing properties and proportions into continuous variables for gradient optimization. After finding the continuous optimum, a designer can analyze near optimal designs for comparison and selection. Design examples show the influence of the bearing lives on the gear parameters in the optimal configurations. For a fixed back-cone distance, optimal designs with larger shaft angles have larger service lives.

Savage, M.↗