Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “test configuration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Surface flow and heating distributions on a cylinder in near wake of Aeroassist Flight Experiment (AFE) configuration at incidence in Mach 10 Air

Experimental heat transfer distributions and surface streamline directions are presented for a cylinder in the near wake of the Aeroassist Flight Experiment forebody configuration. Tests were conducted in air at a nominal free stream Mach number of 10, with post shock Reynolds numbers based on model base height of 6,450 to 50,770, and angles of attack of 5, 0, -5, and -10 degrees. Heat transfer data were obtained with thin film resistance gage and surface streamline directions by the oil flow technique. Comparisons between measured values and predicted values were made by using a Navier-Stokes computer code.

Wells, William L.↗
NASA NTRS1990

Analysis of small-scale rotor hover performance data

Rotor hover-performance data from a 1/6-scale helicopter rotor are analyzed and the data sets compared for the effects of ambient wind, test stand configuration, differing test facilities, and scaling. The data are also compared to full scale hover data. The data exhibited high scatter, not entirely due to ambient wind conditions. Effects of download on the test stand proved to be the most significant influence on the measured data. Small-scale data correlated resonably well with full scale data; the correlation did not improve with Reynolds number corrections.

Kitaplioglu, Cahit↗
NASA NTRS1990

Radiometric tests on wet and dry antenna reflector surface panels

The results of X-band noise temperature tests on two types of antenna surface panels are presented. The first type tested was a solid antenna panel, while the second type was a perforated panel with 3/16-in.-diameter holes. Measurements were made at 8.45 GHz using an X-band radiometric system. Included in this article are measured noise temperature contributions from: (1) thermal diffusive white paint on solid and perforated panels, and (2) water sprayed on both painted and unpainted perforated panels. Experiments on perforated panels were restricted to the 3/16-in.-diameter hole panels formerly used on Deep Space Network 64-m antennas. Rigorous calibration equations, applicable to a variety of antenna panel and dichroic plate test configurations, are presented. It was demonstrated that an accurate, stable radiometric measurement system of the type used for the results of this research makes it possible to obtain information that would be much more difficult to obtain using other techniques.

Otoshi, T. Y.↗
NASA NTRS1989

Active phase compensation system for fiber optic holography

Fiber optic delivery systems promise to extend the application of holography to severe environments by simplifying test configurations and permitting the laser to be remotely placed in a more benign location. However, the introduction of optical fiber leads to phase stability problems. Environmental effects cause the pathlengths of the fibers to change randomly, preventing the formation of stationary interference patterns which are required for holography. An active phase control system has been designed and used with an all-fiber optical system to stabilize the phase difference between light emitted from two fibers, and to step the phase difference by 90 deg without applying any constraints on the placement of the fibers. The accuracy of the phase steps is shown to be better than 0.02 deg., and a stable phase difference can be maintained for 30 min. This system can be applied to both conventional and electro-optic holography, as well as to any system where the maintenance of an accurate phase difference between two coherent beams is required.

Mercer, Carolyn R.↗
NASA NTRS1990

Turbulent flow separation control over a backward-facing ramp via transverse and swept grooves

Separation control experiments were conducted in a 51-71-cm shear-flow control tunnel using a backward-facing ramp to investigate the performance of transverse and swept grooves for controlling a two-dimensional turbulent separated flow at low speeds and moderate Reynolds numbers. In the experiments, transverse grooves, located in the maximum +dP/dx region, with a height-to-width ratio greater than 2.5, reduced the reattachment distance by 20 percent over the baseline configuration. Unlike transverse and longitudinal grooves of equivalent size, the 45-degree swept-groove configurations tested enhanced separation.

Selby, G. V.↗
NASA NTRS1989

An Experimental Method for Measuring Water Droplet Impingement Efficiency on Two- and Three-dimensional Bodies

An experimental method was developed to determine the droplet impingement characteristics on 2-D and 3-D bodies. The experimental results provide the essential droplet impingement data required to validate water droplet trajectory codes, which are used in the analysis of aircraft icing. A body, whose water droplet impingement characteristics are required, is covered at strategic locations by thin strips of moisture absorbing (blotter) paper, and is exposed to an air stream containing a water dye solution spray cloud. Water droplet impingement data are extracted from the dyed blotter strips by measuring the optical reflectance of the dye deposit on the strips, using an automated reflectometer. Models tested include a 4-inch diameter cylinder, a NACA 652015 airfoil section, a MS(1)-0317 supercritical airfoil section, three simulated ice shapes, an axisymmetric inlet and a Boeing 737-300 inlet model. Detailed descriptions of the dye tracer technique, instrumentation, data reduction method and the results obtained are presented. Analytical predictions of collection efficiency characteristics for most test configurations are included for comparison.

Trajectory code validation↗
NASA NTRS1991

Illuminance and luminance distributions of a prototype ambient illumination system for Space Station Freedom

Preliminary results of research conducted in the late 1970's indicate that perceptual qualities of an enclosure can be influenced by the distribution of illumination within the enclosure. Subjective impressions such as spaciousness, perceptual clarity, and relaxation or tenseness, among others, appear to be related to different combinations of surface luminance. A prototype indirect ambient illumination system was developed which will allow crew members to alter surface luminance distributions within an enclosed module, thus modifying perceptual cues to match crew preferences. A traditional lensed direct lighting system was compared to the prototype utilizing the full-scale mockup of Space Station Freedom developed by Marshall Space Flight Center. The direct lensed system was installed in the habitation module with the indirect prototype deployed in the U.S. laboratory module. Analysis centered on the illuminance and luminance distributions resultant from these systems and the implications of various luminaire spacing options. All test configurations were evaluated for compliance with NASA Standard 3000, Man-System Integration Standards.

Mullican, R. C.↗
NASA NTRS1991

A portable Ka-band front-end test package for beam-waveguide antenna performance evaluation. Part 1: Design and ground tests

A unique experimental method was used to test the beam waveguide (BWG) antenna at Deep Space Station (DDS) 13 in the Goldstone Deep Space Communications Complex near Barstow, California. The methodology involved the use of portable test packages to make measurements of operating noise temperatures and antenna efficiencies (as functions of antenna pointing angles) at the Cassegrain focal point and the final focal point located in a subterranean pedestal room. Degradations caused by the BWG mirror systems were determined by making comparisons of the measured parameters at the two focal points of the antenna. Previous articles were concerned with the design, performance characteristics, and test results obtained with an X-band test package operating at 32 GHz. Noise temperature measurement results are presented for the Ka-band test package in an on-the-ground test configuration.

Otoshi, T. Y.↗
NASA NTRS1992

Development of Test-Analysis Models (TAM) for correlation of dynamic test and analysis results

The primary objective of structural analysis of aerospace applications is to obtain a verified finite element model (FEM). The verified FEM can be used for loads analysis, evaluate structural modifications, or design control systems. Verification of the FEM is generally obtained as the result of correlating test and FEM models. A test analysis model (TAM) is very useful in the correlation process. A TAM is essentially a FEM reduced to the size of the test model, which attempts to preserve the dynamic characteristics of the original FEM in the analysis range of interest. Numerous methods for generating TAMs have been developed in the literature. The major emphasis of this paper is a description of the procedures necessary for creation of the TAM and the correlation of the reduced models with the FEM or the test results. Herein, three methods are discussed, namely Guyan, Improved Reduced System (IRS), and Hybrid. Also included are the procedures for performing these analyses using MSC/NASTRAN. Finally, application of the TAM process is demonstrated with an experimental test configuration of a ten bay cantilevered truss structure.

Angelucci, Filippo↗
NASA NTRS1992

The NASA/Industry Design Analysis Methods for Vibrations (DAMVIBS) Program - Boeing helicopters airframe finite element modeling

Finite-element modeling of the airframe vibration of the Army/Boeing CH-47D helicopter is conducted with comparisons to experimental data in an effort to improve the design process. A NASTRAN FEM is developed that is fully representative of the test configuration and includes the support fixture, shakers, and the aircraft/shaker suspension system. The analysis is conducted with specific attention given to the prediction of reasonable forced amplitudes throughout the airframe. Reasonable correlation is noted between the FEM and experimental results, although improved correlation can be obtained by including more accurate damping values and secondary effects such as stringer shear loading. It is shown that the general stress model does not provide an adequate dynamic analysis on which to base design improvements. A more detailed model is required that emphasizes highly detailed helicopter elements and employs a finer mesh particularly in the description of the mass distribution.

Gabel, R.↗
NASA NTRS1992

High pressure turbomachinery ground test facility

Turbomachinery test facilities are at present scarce to non-existent world-wide. The turbomachinery test facility at Stennis Space Center will provide for advanced development and research and development capabilities for liquid hydrogen/liquid oxygen propellant rocket engine components. The facility will provide ultra-high pressure via gas generators to deliver the needed turbine drive on various turbomachinery. State of the art process control systems will provide the vital pressure, temperature and flow requirements during tests. These systems will better control adverse transient conditions during start-up and shutdown, and by using advanced control theory, as well as incorporate test article health monitoring. Also, digital data acquisition systems will obtain high frequency (up to 20 KHz) and low frequency (up to 1 KHz) data during the test. Pressures of up to 15,000 psi will be generated to pressurize high pressure tanks supplying cryogens to various test article inlets thus pushing turbopump materials and manufacturing processes to their limits. By planning for future projects the test facility will be easily adaptable to multi-program test configurations over a range of thermodynamic positions.

Scheuermann, Patrick E.↗
NASA NTRS1992

Vortical flow control on a wing-body combination using tangential blowing

The objective of the experimental program reported here was to evaluate the possibility of using tangential blowing to create roll and yaw control on a delta wing-forebody combination at high angles of attack. It is found that the vortical flow over the model can be manipulated more efficiently by blowing on the nose section rather than fuselage. Large rolling moments and side forces are generated by blowing from forebody compared to wing blowing. For a wing-body combination, a model with a blunt nose is found to be less sensitive to flow asymmetry than a sharp-nosed configuration. Rolling moment changes sign from prestall to stall for all the configurations tested.

Celik, Zeki Z.↗
NASA NTRS1992

Data storage and retrieval system abstract

The STX mass storage system design is intended for environments requiring high speed access to large volumes of data (terabyte and greater). Prior to commitment to a product design plan, STX conducted an exhaustive study of the commercially available off-the-shelf hardware and software. STX also conducted research into the area of emerging technologies in networks and storage media so that the design could easily accommodate new interfaces and peripherals as they came on the market. All the selected system elements were brought together in a demo suite sponsored jointly by STX and ALLIANT where the system elements were evaluated based on actual operation using a client-server mirror image configuration. Testing was conducted to assess the various component overheads and results were compared against vendor data claims. The resultant system, while adequate to meet our capacity requirements, fell short of transfer speed expectations. A product team lead by STX was assembled and chartered with solving the bottleneck issues. Optimization efforts yielded a 60 percent improvement in throughput performance. The ALLIANT computer platform provided the I/O flexibility needed to accommodate a multitude of peripheral interfaces including the following: up to twelve 25MB/s VME I/O channels; up to five HiPPI I/O full duplex channels; IPI-s, SCSI, SMD, and RAID disk array support; standard networking software support for TCP/IP, NFS, and FTP; open architecture based on standard RISC processors; and V.4/POSIX-based operating system (Concentrix). All components including the software are modular in design and can be reconfigured as needs and system uses change. Users can begin with a small system and add modules as needed in the field. Most add-ons can be accomplished seamlessly without revision, recompilation or re-linking of software.

Matheson, Barbara↗
NASA NTRS1993

Thermal performance testing of the Explorer Platform

The Explorer Platform (EP) has been designed to accommodate on-orbit payload and bus module changeout via Space Transportation System (STS) servicing. Such a versatile spacecraft platform designed to experience widely different environmental exposures and operational conditions, coupled with program constraints on schedule and budget, presented a challenge to implementing a technically sound thermal vacuum/thermal balance test program. This paper discusses thermal performance tests implemented at the subsystem and system levels, and the risks accepted resulting from test sequence, configuration. and tests omitted from the program. No thermal cycling or thermal balance tests were performed on the integrated spacecraft level, although both the Payload (EUVE) and Platform (EP) received independent testing. The decision to take this approach is discussed with respect to the thermal design and the associated risks taken to maintain budget and schedule.

Wasson, David↗
NASA NTRS1991

Design and performance of an Automatic Gain Control system for the High Energy X-Ray Timing Experiment

The High Energy X-Ray Timing Experiment (HEXTE), currently under development for the X-Ray Timing Explorer (XTE) mission, employs a closed loop gain control system to attain 0.5 percent stabilization of each of eight-phoswich detector gains. This Automatic Gain Control (AGC) system utilizes a split window discriminator scheme to control the response of each detector pulse height analyzer to gated Am-241 X-ray events at 60 keV. A prototype AGC system has been implemented and tested within the gain perturbation environment expected to be experienced by the HEXTE instrument in flight. The AGC system and test configuration are described. Response, stability and noise characteristics are measured and compared with theoretical predictions. The system is found to be generally suitable for the HEXTE application.

Pelling, Michael R.↗
NASA NTRS1948

The Effect of Boundary-layer Control by Suction and Several High-lift Devices on the Longitudinal Aerodynamic Characteristics of a 47.5 Degree Sweptback Wing-fuselage Combination

An investigation has been made in the Langley full-scale tunnel of a 47.5 degree sweptback wing-fuselage combination equipped for boundary-layer control by suction. The wing aspect ratio was 3.5, the taper ratio was 0.5, and the airfoil sections normal to the quarter-chord line were NACA 64(sub 1)-A112. The wing configurations tested included the wing with various combinations of extensible leading-edge and split flaps. The effect of Reynolds number, suction-slot location and suction flow coefficient on the aerodynamic characteristics was determined for the model at zero yaw over a range of angle of attack.

WING-FUSELAGE COMBINATIONS - AIRPLANES↗
NASA NTRS1956

Simulated afterburner performance with hydrogen peroxide injection for thrust augmentation

Combustion performance of three afterburner configurations was evaluated at simulated altitude flight conditions with liquid augmentation to the primary combustor. Afterburner combustion efficiency and stability were better with injection of high-strength hydrogen peroxide than with no injection or with water injection. Improvements were observed in afterburner configurations with and without flameholders and in a short-length afterburner. At a peroxide-air ratio of 0.3, combustion was stable and 85 to 90 percent efficient in all configurations tested. Calculated augmented net-thrust ratios for peroxide injection with afterburning were approximately 60 percent greater than those for water injection.

Metzler, Allen J↗
NASA NTRS1954

Effect of Horizontal-Tail Span and Vertical Location on the Aerodynamic Characteristics of an Unswept Tail Assembly in Sideslip

An investigation has been conducted in the Langley stability tunnel on a vertical-tail model with a stub fuselage in combination with various horizontal tails to determine the effect of horizontal-tail span and vertical location of the horizontal tail relative to the vertical tail on the aerodynamic characteristics of an unswept tail assembly in sideslip. The results of the investigation indicated that the induced loading carried by the horizontal tail produced a rolling moment about the point of attachment to the vertical tail which was strongly influenced by horizontal-tail span and vertical locations. The greatest effect of horizontal-tail span on the rolling-moment derivative of the complete tail assembly was obtained for horizontal-tail locations near the top of the vertical tail. Span loadings which were reduced to the static-stability derivatives were calculated for each configuration tested by applying the well-known finite-step method used for wings to the intersecting surfaces of the vertical and horizontal tails. The finite-step method provides a simple and effective means of investigating the span loadings of intersecting surfaces.

Riley, Donald R↗