SEARCH · Engineering Papers

Results for “shapes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Silicon ribbon growth by a capillary action shaping technique

Substantial improvements in ribbon surface quality are achieved with a higher melt meniscus than that attainable with the film-fed (EFG) growth technique. A capillary action shaping method is described in which meniscus shaping for the desired ribbon geometry occurs at the vertex of a wettable die. As ribbon growth depletes the melt meniscus, capillary action supplies replacement material. Topics discussed cover experimental apparatus and growth procedures; die materials investigations, fabrication and evaluation; process development for 25 mm, 38 mm, 50 mm and 100 mm silicon ribbons; and long grain direct solidification of silicon. Methods for the structural and electrical characterization of cast silicon ribbons are assessed as well as silicon ribbon technology for the 1978 to 1986 period.

Schwuttke, G. H.↗

NASA NTRS1978

Inlet boundary-layer shapes on four aircraft forebodies at Mach 6

Boundary-layer shape measurements at the engine inlet on four different hypersonic aircraft forebody designs (with no engine on the forebody) are reported. The measurements provide a qualitative assessment of the effectiveness of various forebody geometries as engine inlet precompression surfaces. The designs, tested in a hypersonic tunnel at Mach 6 and a nominal freestream Reynolds number of 30,500,000, included a semiconical forebody, a configuration similar to a slab delta wing, a conical nose blended into a flat surface, and a conical, complex forebody shape. Boundary layer height as a function of forebody compression is shown for each design.

Lawing, P. L.↗

NASA NTRS1978

Analysis of simulated measurements of earth emitted radiation using geometric shape factors, and some results from analysis of ESSA 7 and Nimbus 6 data

In the reported study, simulated measurements of earth radiation with wide field-of-view (WFOV) radiometers are reduced to earth fluxes through geometric shape factors. Estimates of emitted flux for global and zonal scales and for regions smaller than the detector field-of-view are compared to fluxes derived directly from a model. Geometric shape factors are used to estimate global, zonal, and regional averages of earth-emitted flux from measurements with WFOV detectors on the ESSA 7 satellite and the Nimbus 6 satellite. Zonal and global averages of emitted flux for each of the 3-month periods of ESSA 7 data are shown in a graph. Another graph shows zonal and global averages of emitted flux for August 1975 obtained with the aid of Nimbus 6. The data are compared to values reported by Green and Smith (1977) who used a spherical harmonic solution.

Weaver, W. L.↗

NASA NTRS1977

Size-dependence in the shape of fresh impact craters on the moon

The transition from small simple craters to large complex or modified craters is characterized by eleven changes in the shape of fresh lunar craters which occur within a diameter range of 10 to 30 km. In the present paper, seven ratio-level variations - those of rim-crest diameter with depth, rim height, flank width, rimwall slope, floor diameter, circularity, and rim-crest evenness - are defined for fresh-appearing craters from the new Apollo data and are expressed mathematically where practicable. These relations constitute a shape model for interpreting fresh craters on the moon. The size dependent changes reflect the occurrence of central peaks, rimwall terraces, and a flat floor within craters measuring 10 to 20 km in diameter.

Pike, R. J.↗

NASA NTRS1978

Line shapes /absorption coefficients/ for satellites and inversion of the data to obtain interaction potentials

Line shapes for cesium broadened by xenon and neopentane have been measured in an absorption cell. The growth of the red satellites, both primary and secondary, were studied on the first five principal series doublets and on the first S-D forbidden doublet. An inversion scheme based on a nearest-neighbor density was employed to invert the measured line shapes and obtain difference potential estimates. It is apparent from the inversion scheme that minor inflections in the difference potential map into strong features in the frequency plane and that contrary to popular assumption, absolute extrema may not be necessary for satellite interpretation. Strength effects observed on the forbidden satellites also demonstrate that the radial dependence of the dipole moment must be accounted for in certain cases.

Exton, R. J.↗

NASA NTRS1979

Variable-shape solar-energy concentrator

Proposed low cost three dimensional tracking solar concentrator fabricated from lightweight, flexible polymeric film membrane is controlled in shape by differential pressure loading. Fine adjustments to shape could be made by mounting electrets or magnets on membrane or applying electric or magnetic field.

Miller, C. G.↗

NASA NTRS1980

Fabricating wedge-shaped beam splitters

Fast economical fabrication produces wedge-shaped beam splitter with 0.3 micrometer edge, compared to conventional methods that have yielded 2 micrometer edges. Typical beam splitter made by new process is prism-shaped with right-triangle cross-section.

Fleetwood, C. M., Jr.↗

NASA NTRS1978

Computer-aided analysis and design of the shape rolling process for producing turbine engine airfoils

Mild steel (AISI 1018) was selected as model cold rolling material and Ti-6A1-4V and Inconel 718 were selected as typical hot rolling and cold rolling alloys, respectively. The flow stress and workability of these alloys were characterized and friction factor at the roll/workpiece interface was determined at their respective working conditions by conducting ring tests. Computer-aided mathematical models for predicting metal flow and stresses, and for simulating the shape rolling process were developed. These models utilized the upper bound and the slab methods of analysis, and were capable of predicting the lateral spread, roll separating force, roll torque, and local stresses, strains and strain rates. This computer-aided design system was also capable of simulating the actual rolling process, and thereby designing the roll pass schedule in rolling of an airfoil or a similar shape.

Lahoti, G. D.↗

NASA NTRS1979

Measured and predicted shock shapes and aerodynamic coefficients for blunted cones at incidence in helium at Mach 20.3

Experimental values of shock shapes (alpha = 0 degrees and 10 degrees) and static aerodynamic coefficients (alpha = -4 degrees to 12 degrees) for sharp and spherically blunted cones having cone half-angles of 30, 45, 60, and 70 degrees and nose bluntness ratios of 0, 0.25, and 0.50 are presented. Shock shapes were also measured at 0 degree angle of attack by using a flat-faced cylinder (90 degree cone) and a hemispherically blunted cylinder (sphere). All tests were conducted in helium (gamma = 5/3) at a free-stream Mach number of 20.3 and a unit free-stream Reynolds number of 22,400,000 per meter. Comparisons between measured values and predicted values were made by using several numerical and simple engineering methods.

Calloway, R. L.↗

NASA NTRS1979

Normal and radial impact of composites with embedded penny-shaped cracks

A method is developed for the dynamic stress analysis of a layered composite containing an embedded penny-shaped crack and subjected to normal and radial impact. The material properties of the layers are chosen such that the crack lies in a layer of matrix material while the surrounding material possesses the average elastic properties of a two-phase medium consisting of a large number of fibers embedded in the matrix. Quantitatively, the time-dependent stresses near the crack border can be described by the dynamic stress intensity factors. Their magnitude depends on time, on the material properties of the composite and on the relative size of the crack compared to the composite local geometry. Results obtained show that, for the same material properties and geometry of the composite, the dynamic stress intensity factors for an embedded (penny-shaped) crack reach their peak values within a shorter period of time and with a lower magnitude than the corresponding dynamic stress intensity factors for a through-crack.

Sih, G. C.↗

NASA NTRS1978

Analysis of solidification interface shape during continuous casting of a slab

An analysis was made of the two-dimensional interface shape of a slab ingot being cast continuously by withdrawing it from a mold. The sides of the ingot are being cooled and the upper boundary of the ingot is in contact with a pool of molten metal. The solidification interface shape was determined from the analysis of the heat flow, utilizing the condition that the solidification interface is at constant temperature and must be normal to the lines of heat flow carrying away latent heat of fusion from the interface. The analysis includes the effect of interface curvature which, for a constant rate of withdrawing the cast ingot from the mold, causes the solidification to be nonuniform along the interface. The analysis was carried out by a conformal mapping procedure.

Siegel, R.↗

NASA NTRS1979

Radiographic Comparison of Human Lung Shape During Normal Gravity and Weightlessness

Chest radiographs in five seated normal volunteers at 1 G and 0 G were made with a view toward comparing human lung shape during normal gravity and weightlessness. Lung shape was assessed by measuring lung heights and widths in upper, middle and lower lung regions. No significant differences were found between any of the 1-G and 0-G measurements, although there was a slight tendency for the lung to become shorter and wider at 0 G. The evidence that gravity causes regional differences in ventilation by direct action on the lung is consistent with the theoretical analysis of West and Matthews (1972).

Michels, D. B.↗

NASA NTRS1980

Active experiments using rocket-borne shaped charge barium releases

A reliable payload system and scaled down shaped charges were developed for carrying out experiments in solar-terrestrial magnetospheric physics. Four Nike-Tomahawk flights with apogees near 450 km were conducted to investigate magnetospheric electric fields, and two Taurus-Tomahawk rockets were flown in experiments on the auroral acceleration process in discrete auroras. In addition, a radial shaped charge was designed for plasma perturbation experiments.

Wescott, E. M.↗

NASA NTRS1980

Measured and predicted shock shapes and aerodynamic coefficients for blunted cones at incidence in air at Mach 5.9

Experimental values of shock shapes (angles of attack of 0 deg and 10 deg) and static aerodynamic coefficients (angles of attack of -4 deg to 12 deg for sharp and spherically blunted cones having cone half angles of 30 deg, 45 deg, 60 deg, and 70 deg, and nose bluntness ratios of 0, 0.25, and 0.50 are presented. Shock shapes were measured at 0 deg angle of attack by using a flat faced cylinder (90 deg cone) and a hemispherically blunted cylinder (sphere). All tests were conducted in air at a free stream Mach number of 5.9 and a unit free stream Reynolds number of 2,800,000 per meter. Comparisons between measured values and predicted values were made by using several numerical and simple engineering methods.

Calloway, R. L.↗

NASA NTRS1979

Position and shape of the Venus bow shock - Pioneer Venus Orbiter observations

Magnetometer data from the Pioneer Venus Orbiter is used to examine the position and shape of this planet's bow shock. Utilizing crossings identified on 86 occasions during the first 65 orbits a mean shock surface is defined for sun-Venus-satellite angles of 60-110 deg. Both the shock shape and variance in location are found to be very similar to the terrestrial case for the range in SVS angle considered. However, while the spread in shock positions at the earth is due predominantly to the magnetopause location varying in response to solar wind dynamic pressure, ionopause altitude variations can have little effect on total obstacle radius. Thus, the Cytherean shock is sometimes observed much closer to or farther from the planet than previously predicted by gasdynamic theory applied to the deflection of flow about a blunt body which acts neither as source nor sink for any portion of the flow.

Slavin, J. A.↗

NASA NTRS1978

Interpretation of the shape factor at Ootacamund, India

The paper deals with equatorial ATS-6 measurements of the shape factor, F, interpreted in terms of the shape of the electron density profile along the ray path. The observed rapid increase in F at sunrise is attributed to EUV production of ionization in the E and F regions. The evening decrease is seen to result from an upward drift of the F region at sunset and the evening decay of the E and bottomside F regions. The nighttime peak, or plateau, is caused by gradual decrease of the electron density profile.

Donnelly, R. F.↗

NASA NTRS1980

Simulation study of geometric shape factor approach to estimating earth emitted flux densities from wide field-of-view radiation measurements

A study was performed on the use of geometric shape factors to estimate earth-emitted flux densities from radiation measurements with wide field-of-view flat-plate radiometers on satellites. Sets of simulated irradiance measurements were computed for unrestricted and restricted field-of-view detectors. In these simulations, the earth radiation field was modeled using data from Nimbus 2 and 3. Geometric shape factors were derived and applied to these data to estimate flux densities on global and zonal scales. For measurements at a satellite altitude of 600 km, estimates of zonal flux density were in error 1.0 to 1.2%, and global flux density errors were less than 0.2%. Estimates with unrestricted field-of-view detectors were about the same for Lambertian and non-Lambertian radiation models, but were affected by satellite altitude. The opposite was found for the restricted field-of-view detectors.

Weaver, W. L.↗

NASA NTRS1980

Flowfield calculations past an entry probe with ablated nose shape

The effects of ablated nose shapes on the flowfield solutions are studied, using a time-dependent finite-difference method developed by Kumar, et al. (1979). Solutions are obtained for the laminar flow of a radiating mixture of H-He in chemical equilibrium past a blunt axisymmetric body at zero angle of attack. The freestream conditions correspond to a point on a typical Jovian entry trajectory, and the initial probe shape is a 45-deg half-angle spherically blunted cone. It is found that as nose bluntness increases, the following occur: in the nose region, shock standoff distances and radiative heating rates increase substantially; surface pressure level increases, but convective heating rates decrease.

Kumar, A.↗