Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power engineering research”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Hydrogen Production System Scaling Using a High-Fidelity Simulation-Optimization Framework

Proton exchange membrane (PEM) electrolyzers are widely used for hydrogen production, yet few validated, high-fidelity tools can reliably guide scale-up. Using measured performance from a 50-hour hardware-in-the-loop pilot test, a physics-based, plant-level model of a 1.25 MW PEM electrolyzer and its balance-of-plant (BoP) subsystems is developed and validated. The model couples electrochemistry and thermal/flow submodels and is calibrated against pilot test data via a genetic algorithm (GA) workflow. Validation yields a mean absolute percentage error (APE) of 0.43% for cell voltage and stack power. Two scale-out strategies are then benchmarked under a common 7-day wind-and-photovoltaic (PV) profile: (i) linear duplication of 1.25 MW blocks and (ii) shared-BoP architectures. Sharing BoP between stacks reduces BoP energy by 27% at 10 MW and 34% at 100 MW (vs. linear duplication) and improves system specific energy consumption (SEC) to 52.9 and 52.6 kWh/kg, respectively (from 54.0 kWh/kg with linear duplication). Partial-load studies (25-100% set-point) show that cumulative hydrogen production remains nearly constant down to 50% load because all cases use the same weekly renewable-energy input. Below 50%, the power cap limits how much energy can be used within 168 h, which reduces hydrogen output. The model further indicates that the practical operating optimum lies between 50% and 85% load, where efficiency gains begin to appear without significant loss in hydrogen output. Moreover, the efficiency gains at lower loads are offset by reduced production. The validated framework supports scenario-based engineering trade-off studies for large configurations (10-100 MW) and for operating policies under variable renewables.

08 HYDROGEN↗
DOE OSTI2026

Cradle-to-Grave Lifecycle Analysis of U.S. Medium- and Heavy-Duty Vehicle-Fuel Pathways: A Greenhouse Gas Emissions Assessment of Current (2021) and Future (2035) Technologies

This study presents a cradle-to-grave lifecycle analysis of energy use and greenhouse gas (GHG) emissions for U.S. medium- and heavy-duty vehicles across current (2021) and future (2035) technologies using the Greenhouse gas, Regulated Emissions, and Energy use in Technologies (GREET) model with industry-vetted assumptions. Results vary across vehicle classes but point to common trends: today, battery electric vehicles (BEVs) offer significant (10–60%) GHG emissions reduction compared to diesel internal combustion engine vehicles and are the lowest emissions option per ton-mile of cargo movement, followed by hydrogen fuel cell electric vehicles (FCEVs) (5–50% emissions reduction). Emissions savings depend largely on the duty cycle and fuel economy of the vehicle type. Future vehicle technology advancements result in comparable emission reductions associated with BEVs and hydrogen FCEVs. Weight-limited BEV trucks see less per-ton-mile emissions reduction due to the impact of battery weight on increased vehicle weight and reduced payload capacity. By 2035, improvements in vehicle efficiency can reduce emissions across all powertrains. However, very low levels of emissions require switching vehicles’ use-phase fuel/energy to low-carbon fuels and electricity. Renewable diesel, e-fuels, hydrogen produced from natural gas with carbon capture and storage or renewables, and use of low-carbon electricity can all achieve over 70% reduction in GHG emissions from the current day diesel-based internal combustion engine vehicle.

alternative fuels↗
DOE OSTI2023

Water Recovery From Cooling Tower Plumes

According to studies by the UN and the US State Department, we are on the path to an extreme freshwater shortage by 2030. The US’s largest water withdrawal source is power plants, which account for 39% of total US freshwater withdrawals, mostly for cooling. Cooling towers are the most common cooling system. To solve these problems and enable efficient water- based cooling – Infinite Cooling’s novel technology uses electric fields to ionize the air, charge the escaping water leaving cooling towers and direct the water toward mesh collectors where it collects and gets recycled for use in the cooling system. This technology was developed at MIT and was reduced to practice on a lab-scale prototype, and a prototype at the MIT Cogeneration Power Plant. This DOE award funded taking this technology from a lab-scale prototype to TRL 5 on an operating cooling tower in the field at the MIT Nuclear Research Laboratory. The funding helped to design and optimize an electrostatic plume collection system and test it in high-fidelity lab setting and in actual field conditions on a cooling tower. Throughout the award, Infinite Cooling investigated the formation of plumes on cooling towers, used that information to optimize the design, material and electrical properties of the collection device and quantified the collection yield via flow rate and water quality.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

TEAMER: Pitching Foil Crossflow Turbine Efficiency Data

This dataset documents the efficiency testing of a pitching foil crossflow turbine, conducted at the University of New Hampshire's (UNH) Chase Ocean Engineering Laboratory tow tank facility. The tests explored various pitch phases and amplitudes, ranging from 0 to 18 degrees, across different flow speeds and turbine RPMs. Specifically, testing was performed at pitch amplitudes of 0,3,6,9,12,15 and 18 degrees. The results indicate that turbine efficiency improves with increased pitch amplitude, reaching optimal performance at 12 degrees. Modifications were made to the test frame by UNH to enhance the stiffness of the support structure. The testing specifically mapped the efficiency of a single quadrant of the Ocean Renewable Power Company (ORPC) Autonomous Turbine Generator Unit (ATGU), covering the full range of allowable pitching amplitudes and phases. The dataset provides both raw and processed data, including drag and torque measurements, and contains Python scripts used for data processing and visualization. This research was supported by funding from TEAMER RFTS 1 (Request for Technical Support).

16 TIDAL AND WAVE POWER↗
DOE OSTI2025

Single-Atom-Resolved Vibrational Spectroscopy of a Dislocation

Dislocations in III-nitride semiconductors impede heat transport, leading to localized overheating, which severely limits the performance and reliability of optoelectronic and power devices. Current research on phonon–dislocation interactions primarily addresses bulk materials, focusing on the average effects at specific dislocation densities. However, phonon resistance from dislocation scattering arises from both short-range core interactions and long-range strain field interactions, which remain largely unexplored. Here, in this study, electron energy-loss spectroscopy is used to investigate a GaN dislocation. Vibrational modes localized on specific core atoms are revealed, reflecting short-range interactions. Additionally, phonon energy shifts driven by strain fields surrounding the dislocation are observed, reflecting long-range interactions. Ab initio calculations support these findings and draw out additional details. This work establishes a paradigm for probing defect-induced phonon scattering at the single-atom level, revealing how dislocations affect phonon behavior through atomic reconstruction and strain engineering, thus offering insights for designing improved material functionalities.

III-nitride semiconductors↗
DOE OSTI2025

Enabling Secure and Resilient XFC: A Software/Hardware-Security Co-Design Approach

Extremely fast charging (XFC) has the potential to reduce the charging time of battery electric vehicles (BEV) to be equivalent to the filling time of internal combustion engine vehicles (ICEV), thus eliminating one of the few advantages ICEV still poses for light- and heavy-duty vehicles. Enabling XFC will, however, require coordination and cooperation between the grid, charging stations, and the vehicles themselves, which leads to an inevitable increase in the attack surface for all systems combined. In securing the overall system, we must not only embrace traditional cybersecurity, which is chiefly concerned with communications and the operation of digital systems, but also cyber-physical systems security as the proper operation of XFC is critically dependent on systems’ abilities to know about (sense) and interact with (actuate) the physical world. The project team consists of academic and industry researchers with backgrounds in cybersecurity, cyber-physical systems security, learning in adversarial environments, transportation security, grid security and resilience, wireless power transfer, converter design, and battery management systems.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Autonomous Tools for Attack Surface Reduction

The electric power grid is a complex critical infrastructure that forms the lifeline of modern society, and its secure and reliable operation is of paramount importance to national security and economic well being. However, recent findings documented in authoritative sources indicate the threat of cyber-based attacks growing in numbers and sophistication. However, securing the grid against stealthy cyber attacks is a challenging task due to legacy nature of the infrastructure coupled with dynamic nature of threat landscape and ever growing sophistication of the adversaries. Additionally, the grid’s attack surface continues to grow with the increased dependence on digital communications and control that now extends to each consumer through smart meters and distributed energy resources. Unfortunately, this expansive surface increases the grid’s vulnerability and further exposes critical control systems in both substations and control centers. To respond to this emerging need, we had successfully assembled an interdisciplinary team with academic- industry partnership to successfully conduct research, development, evaluation, demonstration, and commercialization of attack surface reduction tools, whose goal is to significantly reduce the cyber attack surface in the North American power grid. Our proposed project was a synergistic collaborative effort leveraging the synergistic expertise of the team members across power systems, cyber security and CPS security, testbeds, field deployments and demonstration, and successful commercialization. The team consisted of leading experts from two major universities – Iowa State University, Washington State University – complemented by reputed researchers from two DOE national laboratories – Pacific Northwest National Lab, and Argonne National Lab, one major utility vendor GE Global Research, and one utility partner – Cedar Falls Utilities (CFU). The team members have proven track record of successful academic-industry collaboration in interdisciplinary R&D projects, and bring onboard some of the best state-of-the-art testbed resources, industry-grade SCADA/EMS/DMS environment for experimentation and field demonstration.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Evaluation of the Specification for Safety-Related Steel Structures for Nuclear Facilities, ANSI/AISC N690-18, for Application to Nuclear Power Plants

This report describes the assessment of the recently published ANSI/AISC N690-18, Specification for Safety-Related Steel Structures for Nuclear Facilities. This work was performed for the U.S. Nuclear Regulatory Commission for potential endorsement of N690-18 for use in the design of nuclear power plants. Currently the NRC endorses the use of an earlier version: N690-1994 (R2004), and thus, a technical review of the updated N690 Specification, which contains significant changes, is warranted. The N690-18 Specification reflects advances and improvements in steel design gained from experience, analytical studies, and experimental data over the years. The N690-18 specification also contains a new Appendix N9 that addresses the design of safety-related steel-plate composite (SC) walls which are a relatively new type of structural member for which previously there has not been any U.S. code or standard that governs its design. The technical review of N690-18 was performed in order to assess the adequacy of the provisions for use by the NRC in updating its regulatory guidance for nuclear power plants. The research developed the technical basis for acceptance of the new specification and also identified areas where additional staff guidance is needed for the design of safety-related steel structures at nuclear power plants. The results of the research have determined that the N690-18 specification is a significant enhancement from the N690-1994 (R2004) edition. The new specification contains substantial upgrades in the design of structural steel and includes new provisions for design of SC wall sections, which can benefit the nuclear power industry as well as the NRC review process. All of the improvements, if endorsed by the NRC with certain regulatory positions, will allow clearer and more consistent regulatory guidance, and will avoid the need for justification by licensees and related reviews each time certain methods or approaches are used.

42 ENGINEERING↗
DOE OSTI2023

Field Scale Testing of the Thermocatalytic Ethylene Production Process Using Ethane and Actual Coal Fired Flue Gas Co 2

This report provides a summary of the work performed and results obtained from a project supported by the US DOE (DE-FE0031713). In this study, Southern Research (SR) completed field-scale demonstration of a rationally designed novel nano-engineered catalyst driven thermochemical process to produce high yield of ethylene by using CO 2 derived from actual coal-fired flue gas and ethane. This process, referred to here as “CO 2 -ODH” due to CO 2 use via oxidative dehydrogenation (ODH) mechanism, follows a modified pathway to classical steam cracking (SC) process of ethylene production thus paving the way for significantly reduced CO 2 footprint, marginally improved thermodynamics, higher product selectivity and lower reaction temperatures.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

Drivetrain Reliability Collaborative 1.5 (DRC1.5) Project: Joint Industry Megawatt Scale Gearbox Field Tests: Cooperative Research and Development (Final Report) CRADA Number CRD-17-00702

A new Department of Energy (DOE)/NREL industry collaboration called the Drivetrain Reliability Collaborative 1.5 (DRC1.5) will undertake field testing on a commercial multi-megawatt wind turbine drivetrain to collect loading data as installed in the turbine to thoroughly characterize drivetrain loads and responses during actual in-field conditions. A chief outcome is to provide publicly available operational loading data to the industry. This will provide a greater understanding of steady-state, transient, and fault response for both the input and output of the drivetrain; thus, facilitating improvements in the drivetrain components, lubrication system, power converter or turbine controller.

17 WIND ENERGY↗
DOE OSTI2022

Fuel property impacts on gaseous and PM emissions from a multi-mode single-cylinder engine

The U.S. Department of Energy’s Co-Optima initiative has focused on improving fuel economy and vehicle performance while reducing emissions through the simultaneous development of emerging sustainable fuels with beneficial properties and advanced combustion strategies. A major thrust has been the development of advanced compression ignition (ACI) combustion strategies of gasoline range fuels in combination with spark-ignited (SI) combustion in a single engine capable of multi-mode operation to achieve high power density with enhanced part load efficiency. The aim of this study was to further the understanding of how emissions from both ACI and SI strategies operating on the same fuels in the same engine are impacted by different fuel properties. This investigation focused on particulate matter (PM) and gaseous hydrocarbon emissions from 6 different fuels across 3 different combustion modes on the same single-cylinder engine designed for multi-mode operation: SI combustion, partial fuel stratification (PFS), and spark-assisted compression ignition (SACI). In each of these modes, 3 different CA50 phasings were studied such that all 6 fuels could be studied at the same phasings. Three of the six different fuels used were specially formulated in a previous investigation to study the impact of fuel distillation and aromatic content while maintaining the research octane number (RON) and octane sensitivity. Additionally, neat isooctane and two ethanol containing fuels (RD5-87 and Co-Optima E30) were studied. Different fuel and phasing impacts on emissions were observed across the three combustion modes. Fuel properties were found to impact soot PM and particle number more than the CA50 phasing, while the phasing had more impact on NOx emissions. The NOx emissions were reduced in the PFS mode for all fuels compared to SI combustion, but the SACI combustion mode did not reduce NOx emissions. Although PFS produced low soot PM emissions like SI, total PM mass emissions were significantly higher due to large organic carbon (OC) PM mass contribution. Both PFS and SACI had greater particle number emission than SI operation with small nuclei mode particles dominating in PFS compared to large agglomeration particles in SACI.

42 ENGINEERING↗
DOE OSTI2025

Synchronous Machine Governor Upgrade

Conventional generation sources play a critical role in the stability and reliability of the electrical grid, particularly as we transition towards more renewable energy sources. To understand and accurately emulate their behavior for optimizing grid operations and ensuring seamless integration with renewable technologies, it is essential to better emulate the grid- and plant-level impacts of conventional generation sources, such as natural gas (NG) driven heat recovery steam generators (HRSGs) and combustion turbines (CTs). Therefore, a governor model is developed in a programmable logic controller (PLC) to investigate the performance of the conventional generator under various dynamic operating conditions and to identify the impact on grid stability in a controlled environment. The governor model aims to enable the hardware-in-the-loop (HIL) based emulation of these conventional generation sources using the existing 2 MVA synchronous machine/generator that is driven by a flexible 2.5 MW variable speed drive. This setup will allow us to replicate the dynamic characteristics and response behaviors of NG-driven HRSGs and CTs. The controls for the emulated conventional plants follow the industry standard and are adjustable, ensuring they accurately reflect the operational capabilities and limitations of real-world systems. These controls include load-following capabilities, ramp rates, startup and shutdown sequences, and emissions characteristics. By incorporating these adjustable controls, we aim to capture the nuanced impacts of conventional generation, such as their ability to provide ancillary services like frequency regulation, voltage support, and spinning reserve. In this report, we simulate two types of dynamic operations: grid-connected and islanding. For each dynamic operation, representative starting sequences are tested, including turbine purge, ignition, speed ramping up, generator excitation and synchronizing, and breaker close. The HIL based tests provides insights for field deployment, specifically the high-fidelity governor model provides results to predict the potential stability and reliability risk and suggest possible integration measures (e.g., generation and load balancing, tuning of governor control parameters). Ultimately, this enhanced emulation capability will be integrated into our Advanced Research on Integrated Energy Systems (ARIES), enabling us to conduct comprehensive studies on the interactions between conventional and renewable energy sources. By better understanding these interactions, we can develop strategies to optimize the overall performance and reliability of the grid. This will support the deployment of advanced grid management techniques, such as demand response, grid-forming inverters, and energy storage systems. The main contributions are summarized as follows: (1) This report introduces a PLC-based governor model for gas turbines. This model accurately simulates the dynamic behavior of conventional generation sources under various operational scenarios; (2) The model is integrated with an HIL testbed that includes a 2.5 MW variable speed drive and a 2 MVA synchronous machine. This setup enables realistic, real-time emulation of conventional power plants, particularly NG driven HRSGs and CTs; (3) The developed model is adaptable to various gas turbine configurations and allows for precise control over parameters such as MW ramp rates. This flexibility makes it a valuable tool for future research and industry collaboration; and (4) By incorporating the model into the National Renewable Energy Laboratory's Advanced Research on Integrated Energy Systems, the report lays the groundwork for future studies on interactions between conventional and renewable energy sources, enhancing the ability to develop advanced grid management strategies.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Pressure Gain, Stability, and Operability of Methane/Syngas Based RDEs Under Steady and Transient Conditions (Final Project Report)

The scope of this work addresses key issues associated with losses associated with the detonation wave and other processes internal to the RDE operation, as well as it develops modeling tools for the evaluation of these losses and exhaust emissions in RDEs. The main challenge in studying RDEs is that RDE performance is highly reliant on the specifics of the design so much so that simple/canonical systems alone cannot provide useful engineering information, but practical RDE designs are sufficiently complex and involve extreme operational environments that detailed access either experimentally (laser diagnostics, for instance) or computationally (direct numerical simulations) are as yet to become practical. To overcome this challenge, we have conducted a combined experimental/simulation/analytical study investigating key phenomena that control the characteristics of operation of RDEs. As a result, the study has developed tools and methods that can be used to evaluate performance and design approaches using reduced-physics models, with the assumptions validated using detailed simulations, and the model prediction tested using experimental observations. The specific objectives of the research were: (1) Develop and demonstrate a low-loss fully axial injection concept, taking advantage of stratification effects to alter the detonation structure and position the wave favorably within the combustor; (2) Obtain stability and operability characteristics of an RDE across operating conditions to aid in the development of operability and performance rules for the operations of other systems; and (3) Develop quantitative metrics for performance gain as well as quantitative description of the loss mechanisms through a combination of diagnostics development, reduced-order modeling, and detailed simulations. The work conducted here has made contribution on design of low-loss inlets that has broad application within the power generation industry for use with pressure gain combustion. The operability and stability of different designs, while focusing on axial air inlet designs, has been analyzed. The effect of nozzle and injection conditions was studied. Models and simulations of exhaust emissions, focusing on NOx emission has been developed and used to investigate how operation of the RDE affect NOx production using Lagrangian analysis of RDE simulations. This work has built on previous programs, with the goal of further understanding operation of RDEs and elevate the readiness of design consideration. In addition, a suite of diagnostic and modeling tools have been developed to obtain quantitative metrics on performance based on measurements, which can be readily transferred to other experimental configurations.

08 HYDROGEN↗
DOE OSTI2024

Research Highlight - Dispatch Optimization, System Design and Cost Benefit Analysis of a Nuclear Reactor with Molten Salt Thermal Storage

We highlight our work from our previous publication titled "Dispatch Optimization, System Design, and Cost Benefit Analysis of a Nuclear Reactor with Molten Salt Thermal Storage" published in MDPI Energies 2022 (doi.org/10.3390/en15103599). Variable renewable energy availability has increased the volatility in energy prices in most markets. Nuclear power plants, with a large ratio of capital to variable costs, have historically operated as base load energy suppliers but the need for more flexible operation is increasing. We simulate the techno-economic performance of a 950 MWt nuclear power plant, based on the Westinghouse lead-cooled fast reactor, coupled with molten salt thermal storage as a method for flexible energy dispatch. We use the System Advisor Model to model the nuclear reactor thermal power input and power cycle operating modes. We combine this robust engineering model with a mixed-integer linear program model for optimized dispatch scheduling. We then simulate the coupled nuclear and thermal storage system under different market scenarios with varying price volatility. We find that the coupled plant outperforms the base plant under markets where energy price peaks fluctuate by a factor of two or more about the mean price. We show that a calculated power purchase agreement price for the plant improves by up to 10% when operating under California energy market conditions. Sensitivity analysis on the thermal storage cost shows that the optimal design remains unchanged even when doubling costs.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Alvin Tollestrup (1924-2020): A Life in Science

Alvin Tollestrup was a physicist and engineer of uncommon insight, intuition, and ingenuity who was revered in life for his essential leadership in the development of superconducting magnets for high-energy accelerators. He exhibited a matchless mastery of what he called freshman physics — though his mastery hardly ended there — and an uncanny gift for joining careful measurements with transparent calculations to reveal the essence of a subject. To watch Alvin at work was to learn how a true scientist formulates and solves a problem. He had other gifts: a nose for significant problems in both science and technology, the ability to draw talented people to an important cause, and a mentor's instinct for spotting gifted junior colleagues and helping them to mature as engineers and scientists. He was also good company! Alvin brought his keen vision about what constitutes important science, along with powerful ambition for the institution and for fundamental science, to considerat ions about Fermilab's future. His questions were uniformly probing, his opinions unfailingly interesting, and his appetite for work consistently inspiring. Among Alvin's many contributions to experimental particle physics — in a career that spanned seven decades — the rich achievements of the Collider Detector at Fermilab Collaboration, of which he was a founder and an enduring leader, stand out. The discovery of the top quark in 1995 earned worldwide acclaim. He reaped individual accolades as well, including election to the National Academy of Sciences. The National Medal of Technology, conferred in 1989, recognized Alvin’s leading role in developing superconducting magnets for Fermilab's Tevatron. Universities Research Association created the Tollestrup Award for Postdoctoral Research, commemorating Alvin's avuncular support for young scientists. This volume celebrates Alvin Tollestrup’s career and the rich, fulfilling life he led beyond the laboratory. Contributions from colleagues and family illuminate many facets of this remarka! ble figure. May old friends savor the memory of the Alvin they knew, while discovering less-familiar parts of his history; and may readers who did not have the opportunity to know Alvin firsthand find inspiration in his exemplary life in science.

Palmer, Mark↗
DOE OSTI2020

Development of Robotic Inspection Systems for In-situ Characterisation Prior to Decommissioning - 20306

The University of Bristol's South West Nuclear Hub is part of two large UK academic research collaborations aiming to reduce the costs of nuclear power by trialing innovative solutions to major decommissioning challenges. Robotics and Artificial Intelligence in Nuclear (RAIN) and the National Centre for Nuclear Robotics (NCNR) are the two collaborations tasked by the UK research councils to coordinate this activity, for the benefit of the nuclear industry. This paper presents a summary of Bristol's research aimed at generating and demonstrating a series of technologies ready for commercialization. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Fingerprinting Interactions between Proteins and Ligands for Facilitating Machine Learning in Drug Discovery

Molecular recognition is fundamental in biology, underpinning intricate processes through specific protein–ligand interactions. This understanding is pivotal in drug discovery, yet traditional experimental methods face limitations in exploring the vast chemical space. Computational approaches, notably quantitative structure–activity/property relationship analysis, have gained prominence. Molecular fingerprints encode molecular structures and serve as property profiles, which are essential in drug discovery. While two-dimensional (2D) fingerprints are commonly used, three-dimensional (3D) structural interaction fingerprints offer enhanced structural features specific to target proteins. Machine learning models trained on interaction fingerprints enable precise binding prediction. Recent focus has shifted to structure-based predictive modeling, with machine-learning scoring functions excelling due to feature engineering guided by key interactions. Notably, 3D interaction fingerprints are gaining ground due to their robustness. Various structural interaction fingerprints have been developed and used in drug discovery, each with unique capabilities. This review recapitulates the developed structural interaction fingerprints and provides two case studies to illustrate the power of interaction fingerprint-driven machine learning. The first elucidates structure–activity relationships in β2 adrenoceptor ligands, demonstrating the ability to differentiate agonists and antagonists. The second employs a retrosynthesis-based pre-trained molecular representation to predict protein–ligand dissociation rates, offering insights into binding kinetics. Despite remarkable progress, challenges persist in interpreting complex machine learning models built on 3D fingerprints, emphasizing the need for strategies to make predictions interpretable. Binding site plasticity and induced fit effects pose additional complexities. Interaction fingerprints are promising but require continued research to harness their full potential.

3D structural interaction fingerprints↗
DOE OSTI2021

Post-Fukushima Research and Development Strategy for MELCOR

Numerous MELCOR modeling improvements and analyses have been performed in the time since the severe accidents at Fukushima Daiichi Nuclear Power Station that occurred in March 2011. This report briefly summarizes the related accident reconstruction and uncertainty analysis efforts. It further discusses a number of potential pursuits to further advance MELCOR modeling and analysis of the severe accidents at Fukushima Daiichi and severe accident modeling in general. Proposed paths forward include further enhancements to identified MELCOR models primarily impacting core degradation calculations, and continued application of uncertainty analysis methods to improve model performance and a develop deeper understanding of severe accident progression.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗