Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “passivating layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 595 records · Page 33

Monocrystalline CdTe solar cells with open-circuit voltage over 1 V and efficiency of 17%

The open-circuit voltages of mature single-junction photovoltaic devices are lower than the bandgap energy of the absorber, typically by a gap of 400 mV. For CdTe, which has a bandgap of 1.5 eV, the gap is larger; for polycrystalline samples, the open-circuit voltage of solar cells with the record efficiency is below 900 mV, whereas for monocrystalline samples it has only recently achieved values barely above 1 V. Here, we report a monocrystalline CdTe/MgCdTe double-heterostructure solar cell with open-circuit voltages of up to 1.096 V. The latticed-matched MgCdTe barrier layers provide excellent passivation to the CdTe absorber, resulting in a carrier lifetime of 3.6 μs. The solar cells are made of 1- to 1.5-μm-thick n-type CdTe absorbers, and passivated hole-selective p-type a-SiC y :H contacts. This design allows CdTe solar cells to be made thinner and more efficient. As a result, the best power conversion efficiency achieved in a device with this structure is 17.0%.

42 ENGINEERING↗

Nanoporous silica gel structures and evolution from reactive force field-based molecular dynamics simulations

Nanoporous silica-rich gel formed on silicate glass surfaces during dissolution in aqueous environment is critical in elucidating the corrosion mechanisms and the long-term residual dissolution behaviors. Silica gel models were created using two types of methods with reactive force field-based molecular dynamics simulations. The results show that the remnant silica gels created from the ISG bulk structure have a more isolated and closed pore morphology and slightly higher glass network connectivity. This contrasts with the gel structures created by hydrogarnet defect formation that exhibit more connected pore morphologies. The remnant gel structures show lower water diffusivity which was explained by the nano-confinement effect of water molecules due to frequent interactions of water molecules with adjacent silica walls and the more isolated pore morphology in the remnant gel structures. These results reveal the complexity in terms of micro and atomic structures of these silica gels, and both structure features have impact on water transport in the gel layer hence the passivating effect that controls the long-term dissolution behavior of these glasses.

36 MATERIALS SCIENCE↗

Highly stabilized and photoluminescence enhancement of ZnS:Mn{sup 2+} nanoparticles in biotin matrix

We synthesized the ZnS:Mn{sup 2+} nanoparticles passivated by biocompatible layer, namely, biotin by chemical precipitation route and studied their temporal evolution for size, structure, optical, and photoluminescence stability. To monitor the structural and optoelectronic properties of the nanoparticles with time, we have characterized the grown product by x-ray diffraction, small angle x-ray scattering, UV visible, and photoluminescence spectroscopic techniques at a regular interval for a period of three months. Results showed that the properties of nanophosphors capped with biotin are remaining the same even after 3 months. Energy dispersive x-ray analysis of 3 month aged sample shows long time compatibility between ZnS:Mn{sup 2+} nanoparticles and the biotin. This is also confirmed by electron microscopy that the growth of the nanoparticles is strongly arrested by the biotin. X-ray photoelectron spectra were also recorded to show the chemical state of the elements. Enhanced ratio of Zn 2p to Mn 2p peaks in the x-ray photoelectron spectra of ZnS:Mn{sup 2+} nanoparticles shows that the Mn{sup 2+} ions are incorporated within ZnS host matrix. We found that biotin capping will enhance the luminescence from ZnS:Mn{sup 2+} nanoparticles as compared to without capped particles. Absence of biotin will gradually degrade the luminescence upon aging while drastic degradation in luminescence intensity was observed after annealing. Properties show that biotin also protected the nanoparticles from any environmental attack.

36 MATERIALS SCIENCE↗

Band alignment at interfaces of amorphous Al{sub 2}O{sub 3} with Ge{sub 1−x}Sn{sub x}- and strained Ge-based channels

Spectroscopy of internal photoemission of electrons from Ge and Ge{sub 1−x}Sn{sub x} (x ≤ 0.08) alloys into amorphous Al{sub 2}O{sub 3} is used to evaluate the energy of the semiconductor valence band top. It is found that in Ge and Ge{sub 1−x}Sn{sub x} the valence bands are aligned within the measurement accuracy (±0.05 eV) irrespective of the strain imposed on the semiconductor or by the kind of passivating inter-layer applied between the semiconductor and alumina. This indicates that the Ge{sub 1−x}Sn{sub x}-stressor approach may be useful for strain engineering in p-channel Ge metal-oxide-semiconductor transistors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nanostructured $\mathrm{GaAs/(Al,Ga)As}$ Waveguide for Low-Density Polariton Condensation from a Bound State in the Continuum

Exciton-polaritons are hybrid light-matter states that arise from strong coupling between an exciton resonance and a photonic cavity mode. As bosonic excitations, they can undergo a phase transition to a condensed state that can emit coherent light without a population inversion. This aspect makes them good candidates for thresholdless lasers, yet short exciton-polariton lifetime has made it difficult to achieve condensation at very low power densities. In this sense, long-lived symmetry-protected states are excellent candidates to overcome the limitations that arise from the finite mirror reflectivity of monolithic microcavities. In this work we use a photonic symmetry-protected bound state in the continuum coupled to an excitonic resonance to achieve state-of-the-art polariton condensation threshold in a GaAs/(Al,Ga)As waveguide. Most important, we show the influence of fabrication control and how surface passivation via atomic layer deposition provides a way to reduce exciton quenching at the grating sidewalls.

74 ATOMIC AND MOLECULAR PHYSICS↗

Evaluation of Carrier Trapping in SiNx Towards Ion Migration Measurements

Sodium ion migration has been implicated in potential induced degradation of the shunting type. The kinetics of sodium migration in silicon nitride can be investigated using a simple capacitance-voltage characterization technique. However, we show that the charge trapping strongly affects the measurement and must be taken into consideration in the experimental approach. Furthermore, we perform a systematic analysis of charge carrier trapping in silicon nitride, allowing us to correct trapping effects that otherwise prevent sodium signal detection. We extract trapping and detrapping time constants both on the order of several hours. This shows that trapping cannot be ignored as it occurs relatively quickly and is constantly evolving in time. Accurate determination of sodium behavior in dielectric layers will facilitate robust co-optimization of these layers for optical, passivation, and barrier properties.

42 ENGINEERING↗

Composition and Band Structure of the Native Oxide Nanolayer on the Ion Beam Treated Surface of the GaAs Wafer

Detailed information on GaAs oxide properties is important for solving the problem of passivating and dielectric layers in the GaAs-based electronics. The elemental and chemical compositions of the native oxide layer grown on the atomically clean surface of an n-GaAs (100) wafer etched by Ar{sup +} ions have been studied by synchrotron-based photoelectron spectroscopy. It has been revealed that the oxide layer is essentially enriched in the Ga{sub 2}O{sub 3} phase which is known to be a quite good dielectric as compared to As{sub 2}O{sub 3}. The gallium to arsenic ratio reaches the value as high as [Ga]/[As] = 1.5 in the course of oxidation. The Ga-enrichment occurs supposedly due to diffusion away of As released in preferential oxidation of Ga atoms. A band diagram was constructed for the native oxide nanolayer on the n-GaAs wafer. It has been shown that this natural nanostructure has features of a p–n heterojunction.

36 MATERIALS SCIENCE↗

In Situ High-Temperature TEM Observation of Inconel Corrosion by Molten Chloride Salts with N 2 , O 2 , or H 2 O

Here, in situ transmission electron microscopy (TEM) diffraction and imaging techniques are used to monitor and quantify corrosion of Inconel-625 by pure molten chloride salts (MgCl 2 – NaCl – KCl) at 500 °C–800 °C in 1.0 atm inert N 2 or pure O2, or by salts which are controllably hydrated in a high vacuum chamber. The isothermal corrosion rate R in inert N 2 increases from 203 ± 30 μ m year –1 at 700 °C to 463 ± 30 μ m year –1 at 800 °C. An oxygen ambient causes a six-fold increase to R = 1261 ± 170 μ m year –1 at 700 °C. Salt hydration dramatically accelerates corrosion to R > 3 × 10 5 μ m year –1 at 700 °C while it leads to a more moderate R = 95 ± 20 and 486 ± 30 μ m year –1 at 500 °C and 600 °C, respectively. These isothermal corrosion rates indicate that the molten chloride corrosion is significantly accelerated by salt hydration at temperatures above 600 °C, where corrosion is aggravated by increased generation and solubility of corrosive HCl gases. Hence, to reduce rate of corrosion it is important to both avoid incorporation of H 2 O into the system at each stage and ensure proper flushing of the system before increasing the temperature beyond 600 °C. Compositional analysis of the corroded cells indicate that corrosion in O 2 ambient is dominated by oxidation of metals by O 2 gas dissolved in the chloride melt, but corrosion in H 2 O ambients is caused by chlorination of metals by dissolved HCl gas and MgOH + ions. So, to reduce rate of corrosion, steps should be taken to tailor chloride melt compositions that has low solubility for HCl and O 2 . All of our corroded samples exhibit passive-protective oxide layers of Cr, Mg, and Ni. In addition, distinct volatile compounds of Ni, Mo and Cr involving NiCl 2 , (Na,K) 2 MoO 4 and CrO 2 (OH) 2 are detected in N 2 , H 2 O, and O 2 ambients, respectively. We believe that corrosion acceleration can be minimized by minimizing formation of volatile by-products or promoting reactions that could convert these volatile compounds to solid phases, as these volatile compounds led to destruction of protective oxide layers.

14 SOLAR ENERGY↗

Computational Approach for Improving Three-Dimensional Sub-Surface Earth Structure for Regional Earthquake Hazard Simulations in the San Francisco Bay Area

In our Exascale Computing Project (ECP) we seek to simulate earthquake ground motions at much higher frequency than is currently possible. Previous simulations in the SFBA were limited to 0.5-1 Hz or lower (Aagaard et al. 2008, 2010), while we have recently simulated the response to 5 Hz. In order to improve confidence in simulated ground motions, we must accurately represent the three-dimensional (3D) sub-surface material properties that govern seismic wave propagation over a broad region. We are currently focusing on the San Francisco Bay Area (SFBA) with a Cartesian domain of size 120 x 80 x 35 km, but this area will be expanded to cover a larger domain. Currently, the United States Geologic Survey (USGS) has a 3D model of the SFBA for seismic simulations. However, this model suffers from two serious shortcomings relative to our application: 1) it does not fit most of the available low frequency (< 1 Hz) seismic waveforms from moderate (magnitude M 3.5-5.0) earthquakes; and 2) it is represented with much lower resolution than necessary for the high frequency simulations (> 5 Hz) we seek to perform. The current model will serve as a starting model for full waveform tomography based on 3D sensitivity kernels. This report serves as the deliverable for our ECP FY2017 Quarter 4 milestone to FY 2018 “Computational approach to developing model updates”. We summarize the current state of 3D seismic simulations in the SFBA and demonstrate the performance of the USGS 3D model for a few selected paths. We show the available open-source waveform data sets for model updates, based on moderate earthquakes recorded in the region. We present a plan for improving the 3D model utilizing the available data and further development of our SW4 application. We project how the model could be improved and present options for further improvements focused on the shallow geotechnical layers using dense passive recordings of ambient and human-induced noise.

58 GEOSCIENCES↗

Chemical composition of the SiO2/InSb interface as determined by X-ray photoelectron spectroscopy

In connection with the relatively poor insulating characteristics of the native oxides of most III-V compound semiconductors, there has been interest in the development of deposited dielectric layers for surface passivation and MOS device fabrication on III-V compound semiconductor substrates. The chemical system of SiO2 deposited on single-crystal InSb substrates has been proposed for the fabrication of IR CCD. The considered investigation is concerned with a detailed examination of the chemical nature of the interactions between deposited and native oxides using X-ray photoelectron spectroscopy (XPS) in conjunction with a chemical-etching technique for depth profiling. The compositional structure of the interfaces obtained in the SiO2/native oxide/InSb system is derived on the basis of an intensity analysis of XPS spectra. Thermal oxidation of the InSb substrate is found to result in an In-rich native oxide and excess elemental Sb at the native oxide/substrate interface.

Vasquez, R. P.↗

The composition and vertical structure of the lower cloud deck on Venus

Excluding the insertion of a probe into the lower Venus atmosphere, the only means of examining the atmospheric properties below the upper cloud layer are by passive or active radio techniques. Particularly, in a radio occultation experiment, the amplitude and Doppler data of a signal which has been refracted by the dense Venus atmosphere provide temperature, pressure, atmospheric density, cloud mass content, and some information about the cloud composition. The Venus orbiting spacecraft Pioneer Venus has provided radio occultation data for more than two years. The present investigation has the primary goal to use the absorption coefficient profiles derived from the radio occultation experiment to determine the mass content and composition of the Venusian lower deck. Attention is given to an experiment description, liquid content calculations, the mass content equation, the subtraction of gaseous absorbers, dielectric constant measurements, the concentration profile, the spherical shell model, and mass content profiles for all orbits.

Cimino, J.↗

Effects of impurities on silicon solar-cell performance

Model analyses indicate that sophisticated solar cell designs (back surface fields, optical reflectors, surface passivation, and double layer antireflective coatings) can produce devices with conversion efficiencies above 20%. To realize this potential, the quality of the silicon from which the cells are made must be improved; and these excellent electrical properties must be maintained during device processing. As the cell efficiency rises, the sensitivity to trace contaminants also increases. For example, the threshold Ti impurity concentraion at which cell performance degrades is more than an order of magnitude lower for an 18% cell than for a 16% cell. Similar behavior occurs for numerous other metal species which introduce deep level traps that stimulate the recombination of photogenerated carriers in silicon. Purification via crystal growth in conjunction with gettering steps to preserve the large diffusion length of the as grown material can lead to the production of devices with efficiencies above 18%, as verified experimentally.

Hopkins, R. H.↗

Impurity effects in silicon for high efficiency solar cells

Model analyses indicate that sophisticated solar cell designs including, e.g., back surface fields, optical reflectors, surface passivation, and double layer antireflective coatings can produce devices with conversion efficiencies above 20 percent (AM1). To realize this potential, the quality of the silicon from which the cells are made must be improved; and these excellent electrical properties must be maintained during device processing. As the cell efficiency rises, the sensitivity to trace contaminants also increases. For example, the threshold Ti impurity concentration at which cell performance degrades is more than an order of magnitude lower for an 18-percent cell. Similar behavior occurs for numerous other metal species which introduce deep level traps that stimulate the recombination of photogenerated carriers in silicon. Purification via crystal growth in conjunction with gettering steps to preserve the large diffusion length of the as-grown material can lead to the production of devices with efficiencies aboved 18 percent, as has been verified experimentally.

Hopkins, R. H.↗

Mechanisms leading to net drag reduction in manipulated turbulent boundary layers

Turbulent boundary layers have been manipulated successfully using passive devices called BLADES (boundary-layer alteration devices) leading to net drag reduction. Measurements of various turbulence quantities including intermittency have led to the identification of some of the mechanisms involved in skin-friction reduction. Velocity and vorticity fluctuations associated with oncoming large scales are inhibited significantly by the manipulator blades and the vorticity shed in their wake. The manipulated boundary layers exhibit a reduced intermittency in the outer part of the layer. The effects of manipulation relax with downstream distance and the boundary layer returns toward normal conditions after 100 or 150 boundary-layer thicknesses.

Guezennec, Y. G.↗

Multilayer mirrors and filters for imaging the earth's inner magnetosphere

The requirements for imaging the inner magnetosphere in the light of 304-A He(+) emission are examined. The expected EUV emission spectrum of the inner magnetosphere is used to establish guidelines for the performance of the imager's multilayer mirrors and filters. The design of multilayer mirrors and the results of a computer search that determines the best multilayer mirror design for this application are discussed. B4C, Be, Si, and SiC are identified as promising top-layer materials for a multilayer 304-A mirror, while Al, Mg, and Mg2Si are recommended for other layers. Si-passivated Te and a combination of Al or Si with B or C are promising filter materials for this application.

Schulze, Dean W.↗

The effects of ion implantation on the tribology of perfluoropolyether-lubricated 440C stainless steel couples

The lubricating lifetime of thin films of a perfluoropolyether (PFPE) based on hexafluoropropene oxide in the presence of ion implanted 440C stainless steel is presented. Stainless steel discs, either unimplanted or implanted with N2, C, Ti, Ti + N2, or Ti + C had a thin film of PFPE (60-400 A) applied to them reproducibly (+/- 20 percent) and uniformly (+/- 15 percent) using a device developed for this study. The lifetimes of these films were quantified by measuring the number of sliding-wear cycles required to induce an increase in the friction coefficient from an initial value characteristic of the lubricated wear couple to a final, or failure value, characteristic of an unlubricated, unimplanted couple. The tests were performed in a dry nitrogen atmosphere (less than 1 percent RH) at room temperature using a 3 N normal load with a relative sliding speed of 0.05 m/s. The lubricated lifetime of the 440C couple was increased by an order of magnitude by implanting the disc with Ti. Ranked from most to least effective, the implanted species were: Ti; Ti+C; unimplanted; N2; C approximately equals Ti+N2. The mechanism postulated to explain these results involves the formation of a passivating or reactive layer which inhibits or facilitates the production of active sites. The corresponding surface microstructures induced by ion implantation, obtained using x-ray diffraction and conversion electron Mossbauer spectroscopy, ranked from most to least effective in enhancing lubricant lifetime were: amorphous Fe-Cr-Ti; amorphous Fe-Cr-Ti-C + TiC; unimplanted; epsilon-(Fe,Cr)(sub x)N, x = 2 or 3; amorphous Fe-Cr-C approximately equals amorphous Fe-Cr-Ti-N.

Shogrin, Bradley↗

Hypercars: The next industrial revolution

The auto industry -- one-seventh of the GNP, and the highest expression of the Iron Age -- is about to trigger the biggest transformation in industrial structure since the microchip. Ultralight cars molded from net-shape advanced composites can be several-fold lighter than present steel cars, yet safer, sportier, and more comfortable, durable, and beautiful. Modern hybrid-electric drives boost efficiency approximately 1.3-1.5x in heavy steel cars, but approximately 5-20x in ultralight, very slippery plafforms. Synergistically combined into ultralight-hybrid 'hypercars,' these elements can yield state-of-the-shelf family cars that average 150-300+ mi/gal -- twice that with state-of-the-art technologies -- yet can also be superior in all other respects, probably including cost: carbon-fiber monocoques can actually be cheaper to mass-produce that steel unibodies. Designing cars more like aircraft and less like tanks requires not only an approximately 400-500 kg curb mass and very low air and road drag, but also an aerospace philosophy of engineering integration. Mass, cost, and complexity turn out to compound with heavy hybrids but to decompound with ultralight hybrids, owing partly to radical simplification. Excellent aerodynamics, preferable including advanced techniques for passive boundary-layer control, will be the key to successful design integration. Transforming automaking is a competitive and environmental imperative, could form the nucleus of a green industrial Renaissance, and would enhance national security by, among other things, saving as much oil as OPEC now extracts. However, this transformation faces serious cultural barriers. For example, hypercars will be more like computers with wheels than like cars with chips -- they'll have an order of magnitude more code than today's cars -- but Detroit is not a software culture. Just the transition from stamped and welded steel to integrated and adhesive-joined synthetics is difficult enough. Nonetheless, hypercars are rapidly heading to market in the late 1990s, because approximately 25 current and intending automakers are eager to capture their potentially decisive competitive advantages -- including order-of-magnitude reductions in product cycle time, tooling cost, assembly effort, and parts count. Hypercars will succeed, and may well sweep the market, not because of mandates or subsidies, but because of manufacturers' quest for competitive advantage and customers' desire for better, smarter cars.

Lovins, Amory B.↗